From: Andrea Righi <arighi@nvidia.com>
To: Tejun Heo <tj@kernel.org>
Cc: David Vernet <void@manifault.com>,
Changwoo Min <changwoo@igalia.com>,
sched-ext@lists.linux.dev, Emil Tsalapatis <emil@etsalapatis.com>,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH sched_ext/for-7.1-fixes] sched_ext: Fix deadlock between scx_root_disable() and concurrent forks
Date: Sun, 17 May 2026 12:56:34 +0200 [thread overview]
Message-ID: <agme4i4w5K6Ab9cM@gpd4> (raw)
In-Reply-To: <39ab37b4e79c6e5361a907c06ab27e72@kernel.org>
Hi Tejun,
On Sat, May 16, 2026 at 02:41:20PM -1000, Tejun Heo wrote:
> scx_root_disable() enters SCX_DISABLING before it grabs scx_enable_mutex to
> clear [__]scx_switching_all. task_should_scx() short-circuits on DISABLING,
> so forks in that window land on fair while next_active_class() still skips
> fair - the new tasks stall.
>
> This can deadlock the disable path itself: scx_alloc_and_add_sched() runs
> under scx_enable_mutex and creates a helper kthread; if that new kthread is
> one of the stalled fair tasks, the mutex holder waits forever and
> scx_root_disable() can never make progress. Only sub-sched support exposes
> this, since sub-sched enables are the only path where
> scx_alloc_and_add_sched() can race the root's disable.
>
> Move the DISABLING check after @scx_switching_all so that whenever
> @scx_switching_all is set, forks keep going to scx and stay in lockstep with
> __scx_switched_all. Once both are cleared (together under the mutex),
> DISABLING applies normally.
>
> Fixes: 337ec00b1d9c ("sched_ext: Implement cgroup sub-sched enabling and disabling")
> Signed-off-by: Tejun Heo <tj@kernel.org>
> ---
> kernel/sched/ext.c | 23 ++++++++++++++++++++++-
> 1 file changed, 22 insertions(+), 1 deletion(-)
>
> --- a/kernel/sched/ext.c
> +++ b/kernel/sched/ext.c
> @@ -5092,10 +5092,31 @@ static const struct kset_uevent_ops scx_
> */
> bool task_should_scx(int policy)
> {
> - if (!scx_enabled() || unlikely(scx_enable_state() == SCX_DISABLING))
> + /* if disabled, nothing should be on it */
> + if (!scx_enabled())
> return false;
> +
> + /* scx is taking over all SCHED_OTHER and SCHED_EXT tasks */
> if (READ_ONCE(scx_switching_all))
> return true;
> +
> + /*
> + * scx is tearing down - keep new SCHED_EXT tasks out.
> + *
> + * Must come after scx_switching_all test. While both are set, we must
> + * return true via the branch above: [__]scx_switching_all are cleared
> + * together under scx_enable_mutex, and a fork routed to fair while
> + * __scx_switched_all is still on would stall because
> + * next_active_class() skips fair.
Just being extra picky: [__]scx_switching_all are cleared together sequentially,
but not atomically (in fact the order is what matters). To make it more clear,
how about rephrasing the comment block above like this:
* Must come after the scx_switching_all test. scx_root_disable()
* clears __scx_switched_all before scx_switching_all (both under
* scx_enable_mutex), so while scx_switching_all is observed as true,
* __scx_switched_all may still be on. A fork routed to fair in that
* window would stall because next_active_class() skips fair.
> + *
> + * This can develop into a deadlock - scx holds scx_enable_mutex across
> + * kthread_create() in scx_alloc_and_add_sched(); if the new kthread is
> + * the stalled task, the disable path can never grab the mutex to clear
> + * scx_switching_all.
> + */
> + if (unlikely(scx_enable_state() == SCX_DISABLING))
> + return false;
> +
> return policy == SCHED_EXT;
> }
>
Other than that, looks good to me.
Reviewed-by: Andrea Righi <arighi@nvidia.com>
Thanks,
-Andrea
next prev parent reply other threads:[~2026-05-17 10:56 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-05-17 0:41 [PATCH sched_ext/for-7.1-fixes] sched_ext: Fix deadlock between scx_root_disable() and concurrent forks Tejun Heo
2026-05-17 10:56 ` Andrea Righi [this message]
2026-05-17 17:25 ` Tejun Heo
2026-05-17 17:43 ` [PATCH v2 " Tejun Heo
2026-05-17 18:47 ` Andrea Righi
2026-05-17 19:08 ` Tejun Heo
2026-05-17 19:15 ` Tejun Heo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=agme4i4w5K6Ab9cM@gpd4 \
--to=arighi@nvidia.com \
--cc=changwoo@igalia.com \
--cc=emil@etsalapatis.com \
--cc=linux-kernel@vger.kernel.org \
--cc=sched-ext@lists.linux.dev \
--cc=tj@kernel.org \
--cc=void@manifault.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox