Re: Solution - AMI megaraid driver doesn't work with Linux 2.4.x kernels

Re: Solution - AMI megaraid driver doesn't work with Linux 2.4.x kernels

[Venkatesh Ramamurthy]

Can you provide the dmesg output of your system after loading the driver
either successfully or unsucessfully.

----- Original Message -----
From: "Rafael Martinez" <rafael@viewpoint.no>
To: <linux-kernel@vger.kernel.org>
Sent: Thursday, May 03, 2001 11:37 AM
Subject: Solution - AMI megaraid driver doesn't work with Linux 2.4.x
kernels


> Hei
>
> The Ami megatrends driver (at least for 471, 475, and 493) does not work
> with 2.4.x kernels.
>
> The solution we got from Ami is to update the firmware of these cards to
> version FW G158. This update will fix all the problems with ami
> raid-devices in 2.4.x kernel without changing the driver.
>
> We don't know when AMI will release a fixed firmware (hope soon) but we
got it by
> e-mail. If there is anybody with the same problem I can sent the
> firmware-update by mail.
>
> Sincerely
> Rafael Martinez
>
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/
>

Solution - AMI megaraid driver doesn't work with Linux 2.4.x kernels

[Rafael Martinez]

Hei

The Ami megatrends driver (at least for 471, 475, and 493) does not work 
with 2.4.x kernels.

The solution we got from Ami is to update the firmware of these cards to
version FW G158. This update will fix all the problems with ami
raid-devices in 2.4.x kernel without changing the driver.

We don't know when AMI will release a fixed firmware (hope soon) but we got it by
e-mail. If there is anybody with the same problem I can sent the
firmware-update by mail.

Sincerely
Rafael Martinez

Re: Solution - AMI megaraid driver doesn't work with Linux 2.4.x kernels

[Rafael Martinez]

---Reply to mail from Venkatesh Ramamurthy about Solution - AMI  megaraid driver doesn't work with Linux 2.4.x kernels
> Can you provide the dmesg output of your system after loading the driver
> either successfully or unsucessfully.
> 

Successfully: (Raid 5 4x18GB)
------------------------------------------------------
megaraid: v1.14g (Release Date: Feb 5, 2001; 11:42)
megaraid: found 0x101e:0x1960:idx 0:bus 9:slot 0:func 0
scsi3 : Found a MegaRAID controller at 0xf884e000, IRQ: 17
scsi3 : Enabling 64 bit support
megaraid: [G158:3.11] detected 1 logical drives
scsi3 : AMI MegaRAID G158 254 commands 16 targs 2 chans 40 luns
scsi3: scanning channel 1 for devices.
  Vendor: ESG-SHV   Model: SCA HSBP M9       Rev: 0.10
  Type:   Processor                          ANSI SCSI revision: 02
scsi3: scanning channel 2 for devices.
scsi3: scanning virtual channel for logical drives.
  Vendor: MegaRAID  Model: LD0 RAID5 52527R  Rev: G158
  Type:   Direct-Access                      ANSI SCSI revision: 02
Attached scsi disk sdb at scsi3, channel 2, id 0, lun 0
SCSI device sdb: 107575296 512-byte hdwr sectors (55079 MB)
 sdb: sdb1
-------------------------------------------------------

When it was unsucessfully, it stoppet in the last line with:
sdb: unknown partition table 
(With kernel 2.4.2-2smp from redhat (RH7.1) and "official" 2.4.2, 2.4.3)

The only different between the to instalations is the firmware version
C158 --> G158 of the ami card.

The kernel is a 2.4.2-2smp from redhat (RH7.1). I will test the system with an
"official" ;-) kernel today.

Rafael Martinez

---End reply