[PATCH v8 0/2] Adding device tree and binding for NVIDIA GB200-UT3.0b

[PATCH v8 0/2] Adding device tree and binding for NVIDIA GB200-UT3.0b

[Donald Shannon]

Patch 1 adds the binding for the NVIDIA GB200-UT3.0b platform.
Patch 2 adds the device tree for the NVIDIA GB200-UT3.0b platform.

This is an Aspeed AST2600 based unit testing platform for GB200.
UT3.0b is different than nvidia-gb200nvl-bmc due to networking topology
differences, additional gpio expanders, and voltage regulator gating
some devices.

Reference to Ast2600 SOC [1].
Reference to Blackwell GB200NVL Platform [2].

Link: https://www.aspeedtech.com/server_ast2600/ [1]
Link: https://nvdam.widen.net/s/wwnsxrhm2w/blackwell-datasheet-3384703 [2]
Signed-off-by: Donald Shannon <donalds@nvidia.com>
---
Changes v1 -> v2:
  - Changed phy-mode to rgmii-id [Lunn]
  - Removed redundant max-speed for mac0 [Lunn]
  - Fixed typo from gb200nvl to gb200 in Makefile
Changes v2 -> v3:
 - Fixed whitespace issues [Krzysztof]
 - Fixed schema validation issues from my end ( there are still issues
 with the aspeed dtsi file that are not related to this new dts)
 [Herring]
 - Reordered to follow style guide [Krzysztof]
 - Removed redundant status okays
 - Changed vcc to vdd for the power gating on the gpio expanders
Changes v3 -> v4:
  - Added changelog [Krzysztof]
  - Added nvidia,gb200-ut30b board binding [Krzysztof]
  - Removed unused imports
  - Reordered a couple other style guide violations
  - Added back in a couple needed "status okay"s
Changes v4 -> v5:
 - Resumed my patch after a pause
 - Don't plan to make this include of nvidia-gb200nvl-bmc due to some
 platform differences
 - Fixed io expanders that weren't gated by the 3.3V standby regulator
 - Fixed incorrect interrupt pin for one IO expander
 - Removed some IO expanders and I2C busses
Changes v5 -> v6:
 - Fixed subject line
 - Added missing gpio-key compatible type to buttons
 - Added Acked-by for Krzysztof
Changes v6 -> v7:
  - Removed Acked-by Krzysztof
Changes v7 -> v8:
  - Added missing linux,code for identify and uid button
  - Added Acked-by for Krzysztof
---

Donald Shannon (2):
  dt-bindings: arm: aspeed: Add NVIDIA GB200-UT3.0b  board
  ARM: dts: aspeed: Add NVIDIA GB200 UT3.0b board

 .../bindings/arm/aspeed/aspeed.yaml           |    1 +
 arch/arm/boot/dts/aspeed/Makefile             |    1 +
 .../aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts  | 1030 +++++++++++++++++
 3 files changed, 1032 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts


base-commit: 05adbee3ad528100ab0285c15c91100e19e10138
-- 
2.43.0

[PATCH v8 1/2] dt-bindings: arm: aspeed: Add NVIDIA GB200-UT3.0b board

[Donald Shannon]

This is an Aspeed AST2600 based unit testing platform for GB200.
UT3.0b is different than nvidia-gb200nvl-bmc due to networking topology
differences, additional gpio expanders, and voltage regulator gating
some devices.

Reference to Ast2600 SOC [1].
Reference to Blackwell GB200NVL Platform [2].

Link: https://www.aspeedtech.com/server_ast2600/ [1]
Link: https://nvdam.widen.net/s/wwnsxrhm2w/blackwell-datasheet-3384703 [2]
Signed-off-by: Donald Shannon <donalds@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
index 456dbf7b5ec8..624581db2330 100644
--- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
+++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
@@ -99,6 +99,7 @@ properties:
               - inventec,starscream-bmc
               - inventec,transformer-bmc
               - jabil,rbp-bmc
+              - nvidia,gb200-ut30b
               - nvidia,gb200nvl-bmc
               - qcom,dc-scm-v1-bmc
               - quanta,s6q-bmc
-- 
2.43.0

[PATCH v8 2/2] ARM: dts: aspeed: Add NVIDIA GB200 UT3.0b board

[Donald Shannon]

This is an Aspeed AST2600 based unit testing platform for GB200.
UT3.0b is different than nvidia-gb200nvl-bmc due to networking topology
differences, additional gpio expanders, and voltage regulator gating
some devices.

Reference to Ast2600 SOC [1].
Reference to Blackwell GB200NVL Platform [2].

Link: https://www.aspeedtech.com/server_ast2600/ [1]
Link: https://nvdam.widen.net/s/wwnsxrhm2w/blackwell-datasheet-3384703 [2]
Signed-off-by: Donald Shannon <donalds@nvidia.com>
---
 arch/arm/boot/dts/aspeed/Makefile             |    1 +
 .../aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts  | 1030 +++++++++++++++++
 2 files changed, 1031 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts

diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
index aba7451ab749..37edc4625a9f 100644
--- a/arch/arm/boot/dts/aspeed/Makefile
+++ b/arch/arm/boot/dts/aspeed/Makefile
@@ -51,6 +51,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-lenovo-hr630.dtb \
 	aspeed-bmc-lenovo-hr855xg2.dtb \
 	aspeed-bmc-microsoft-olympus.dtb \
+	aspeed-bmc-nvidia-gb200-ut30b.dtb \
 	aspeed-bmc-nvidia-gb200nvl-bmc.dtb \
 	aspeed-bmc-opp-lanyang.dtb \
 	aspeed-bmc-opp-mowgli.dtb \
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts
new file mode 100644
index 000000000000..3a5404d8cc77
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts
@@ -0,0 +1,1030 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "AST2600 GB200 UT3.0b BMC";
+	compatible = "nvidia,gb200-ut30b", "aspeed,ast2600";
+
+	aliases {
+		serial2 = &uart3;
+		serial4 = &uart5;
+		i2c16   = &imux16;
+		i2c17   = &imux17;
+		i2c18   = &imux18;
+		i2c19   = &imux19;
+		i2c20   = &imux20;
+		i2c21   = &imux21;
+		i2c22   = &imux22;
+		i2c23   = &imux23;
+		i2c24   = &imux24;
+		i2c25   = &imux25;
+		i2c26   = &imux26;
+		i2c27   = &imux27;
+		i2c28   = &imux28;
+		i2c29   = &imux29;
+		i2c30   = &imux30;
+		i2c31   = &imux31;
+		i2c32   = &imux32;
+		i2c33   = &imux33;
+		i2c34   = &imux34;
+		i2c35   = &imux35;
+		i2c36   = &imux36;
+		i2c37   = &imux37;
+		i2c38   = &imux38;
+		i2c39   = &imux39;
+		i2c40	= &e1si2c0;
+		i2c41	= &e1si2c1;
+		i2c42	= &e1si2c2;
+		i2c43	= &e1si2c3;
+		i2c48	= &i2c17mux0;
+		i2c49	= &i2c17mux1;
+		i2c50	= &i2c17mux2;
+		i2c51	= &i2c17mux3;
+		i2c52	= &i2c25mux0;
+		i2c53	= &i2c25mux1;
+		i2c54	= &i2c25mux2;
+		i2c55	= &i2c25mux3;
+		i2c56	= &i2c29mux0;
+		i2c57	= &i2c29mux1;
+		i2c58	= &i2c29mux2;
+		i2c59	= &i2c29mux3;
+	};
+
+	buttons {
+		compatible = "gpio-keys";
+		button-power {
+			label = "power_btn";
+			linux,code = <116>;
+			gpios = <&sgpiom0 156 GPIO_ACTIVE_LOW>;
+		};
+		button-uid {
+			label = "uid_btn";
+			linux,code = <478>;
+			gpios = <&sgpiom0 154 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-0 {
+			label = "uid_led";
+			gpios = <&sgpiom0 27 GPIO_ACTIVE_LOW>;
+		};
+		led-1 {
+			label = "fault_led";
+			gpios = <&sgpiom0 29 GPIO_ACTIVE_LOW>;
+		};
+		led-2 {
+			label = "power_led";
+			gpios = <&sgpiom0 31 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reg_3v3_stby: regulator-3v3-standby {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3-standby";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio0 ASPEED_GPIO(M, 3) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		vga_memory: framebuffer@9f000000 {
+			no-map;
+			reg = <0x9f000000 0x01000000>; /* 16M */
+		};
+
+		ramoops@a0000000 {
+			compatible = "ramoops";
+			reg = <0xa0000000 0x100000>; /* 1MB */
+			record-size = <0x10000>; /* 64KB */
+			max-reason = <2>; /* KMSG_DUMP_OOPS */
+		};
+
+		gfx_memory: framebuffer {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+		};
+
+		video_engine_memory: jpegbuffer {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x02000000>;	/* 32M */
+			alignment = <0x01000000>;
+		};
+	};
+};
+
+// Enable Primary flash on FMC for bring up activity
+&fmc {
+	status = "okay";
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+		status = "okay";
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			u-boot@0 {
+				// 896KB
+				reg = <0x0 0xe0000>;
+				label = "u-boot";
+			};
+
+			kernel@100000 {
+				// 9MB
+				reg = <0x100000 0x900000>;
+				label = "kernel";
+			};
+
+			rofs@a00000 {
+				// 55292KB (extends to end of 64MB SPI - 4KB)
+				reg = <0xa00000 0x35FF000>;
+				label = "rofs";
+			};
+		};
+	};
+};
+
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi2_default>;
+	status = "okay";
+	// Data SPI is 64MB in size
+	flash@0 {
+		label = "config";
+		spi-max-frequency = <50000000>;
+		status = "okay";
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			u-boot-env@0 {
+				// 256KB
+				reg = <0x0 0x40000>;
+				label = "u-boot-env";
+			};
+
+			rwfs@40000 {
+				// 16MB
+				reg = <0x40000 0x1000000>;
+				label = "rwfs";
+			};
+
+			log@1040000 {
+				// 40MB
+				reg = <0x1040000 0x2800000>;
+				label = "log";
+			};
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mac0 {
+	pinctrl-names = "default";
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	pinctrl-0 = <&pinctrl_rgmii1_default>;
+	status = "okay";
+};
+
+// USB Port B Controller
+&ehci1 {
+	status = "okay";
+};
+
+// USB Port B Controller
+&uhci {
+	status = "okay";
+};
+
+// USB port A vhub
+&vhub {
+	status = "okay";
+};
+
+&rng {
+	status = "okay";
+};
+
+&video {
+	memory-region = <&video_engine_memory>;
+	status = "okay";
+};
+
+&gpio0 {
+	gpio-line-names =
+		/*A0-A7*/ "", "", "", "", "", "", "", "",
+		/*B0-B7*/ "", "", "", "", "", "", "", "",
+		/*C0-C7*/ "SGPIO_I2C_MUX_SEL-O", "", "", "", "", "", "", "",
+		/*D0-D7*/ "", "", "", "UART1_MUX_SEL-O", "", "FPGA_PEX_RST_L-O", "", "",
+		/*E0-E7*/ "RTL8221_PHY_RST_L-O", "RTL8211_PHY_INT_L-I",	"", "UART3_MUX_SEL-O",
+					"", "", "", "SGPIO_BMC_EN-O",
+		/*F0-F7*/ "", "", "", "", "", "", "", "",
+		/*G0-G7*/ "", "", "", "", "", "", "", "",
+		/*H0-H7*/ "", "", "", "", "", "", "", "",
+		/*I0-I7*/ "", "", "", "", "", "QSPI2_RST_L-O", "GLOBAL_WP_BMC-O", "BMC_DDR4_TEN-O",
+		/*J0-J7*/ "", "", "", "", "", "", "", "",
+		/*K0-K7*/ "", "", "", "", "", "", "", "",
+		/*L0-L7*/ "", "", "", "", "", "", "", "",
+		/*M0-M7*/ "PCIE_EP_RST_EN-O", "BMC_FRU_WP-O", "FPGA_RST_L-O", "STBY_POWER_EN-O",
+					"STBY_POWER_PG-I", "PCIE_EP_RST_L-O", "", "",
+		/*N0-N7*/ "", "", "", "", "", "", "", "",
+		/*O0-O7*/ "", "", "", "", "", "", "", "",
+		/*P0-P7*/ "", "", "", "", "", "", "", "",
+		/*Q0-Q7*/ "", "", "", "", "", "", "", "",
+		/*R0-R7*/ "", "", "", "", "", "", "", "",
+		/*S0-S7*/ "", "", "", "", "", "", "", "",
+		/*T0-T7*/ "", "", "", "", "", "", "", "",
+		/*U0-U7*/ "", "", "", "", "", "", "", "",
+		/*V0-V7*/ "AP_EROT_REQ-O", "EROT_AP_GNT-I", "", "","PCB_TEMP_ALERT-I", "","", "",
+		/*W0-W7*/ "", "", "", "", "", "", "", "",
+		/*X0-X7*/ "", "", "TPM_MUX_SEL-O", "", "", "", "", "",
+		/*Y0-Y7*/ "", "", "", "EMMC_RST-O", "","", "", "",
+		/*Z0-Z7*/ "BMC_READY-O","", "", "", "", "", "", "";
+};
+
+&gpio1 {
+	/* 36 1.8V GPIOs */
+	gpio-line-names =
+		/*A0-A7*/ "", "", "", "", "", "", "", "",
+		/*B0-B7*/ "", "", "", "", "", "", "IO_EXPANDER_INT_L-I","",
+		/*C0-C7*/ "", "", "", "", "", "", "", "",
+		/*D0-D7*/ "", "", "", "", "", "", "SPI_HOST_TPM_RST_L-O", "SPI_BMC_FPGA_INT_L-I",
+		/*E0-E7*/ "", "", "", "", "", "", "", "";
+};
+
+&sgpiom0 {
+	ngpios = <128>;
+	status = "okay";
+	gpio-line-names =
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"RUN_POWER_FAULT_L-I","SYS_RST_IN_L-O",
+		"RUN_POWER_PG-I","PWR_BRAKE_L-O",
+		"SYS_RST_OUT_L-I","RUN_POWER_EN-O",
+		"L0L1_RST_REQ_OUT_L-I","SHDN_FORCE_L-O",
+		"L2_RST_REQ_OUT_L-I","SHDN_REQ_L-O",
+		"SHDN_OK_L-I","UID_LED_N-O",
+		"BMC_I2C1_FPGA_ALERT_L-I","SYS_FAULT_LED_N-O",
+		"BMC_I2C0_FPGA_ALERT_L-I","PWR_LED_N-O",
+		"FPGA_RSVD_FFU3-I","",
+		"FPGA_RSVD_FFU2-I","",
+		"FPGA_RSVD_FFU1-I","",
+		"FPGA_RSVD_FFU0-I","BMC_I2C_SSIF_ALERT_L-O",
+		"CPU_BOOT_DONE-I","JTAG_MUX_SELECT-O",
+		"SPI_BMC_FPGA_INT_L-I","RTC_CLR_L-O",
+		"THERM_BB_WARN_L-I","UART_MUX_SEL-O",
+		"THERM_BB_OVERT_L-I","",
+		"CPU0_UPHY3_PRSNT1_L-I","IOBRD0_RUN_POWER_EN-O",
+		"CPU0_UPHY3_PRSNT0_L-I","IOBRD1_RUN_POWER_EN-O",
+		"CPU0_UPHY2_PRSNT1_L-I","FPGA_RSVD_FFU4-O",
+		"CPU0_UPHY2_PRSNT0_L-I","FPGA_RSVD_FFU5-O",
+		"CPU0_UPHY1_PRSNT1_L-I","FPGA_RSVD_FFU6-O",
+		"CPU0_UPHY1_PRSNT0_L-I","FPGA_RSVD_FFU7-O",
+		"CPU0_UPHY0_PRSNT1_L-I","RSVD_NV_PLT_DETECT-O",
+		"CPU0_UPHY0_PRSNT0_L-I","SPI1_INT_L-O",
+		"CPU1_UPHY3_PRSNT1_L-I","",
+		"CPU1_UPHY3_PRSNT0_L-I","HMC_EROT_MUX_STATUS",
+		"CPU1_UPHY2_PRSNT1_L-I","",
+		"CPU1_UPHY2_PRSNT0_L-I","",
+		"CPU1_UPHY1_PRSNT1_L-I","",
+		"CPU1_UPHY1_PRSNT0_L-I","",
+		"CPU1_UPHY0_PRSNT1_L-I","",
+		"CPU1_UPHY0_PRSNT0_L-I","",
+		"FAN1_PRESENT_L-I","",
+		"FAN0_PRESENT_L-I","",
+		"","",
+		"IPEX_CABLE_PRSNT_L-I","",
+		"M2_1_PRSNT_L-I","",
+		"M2_0_PRSNT_L-I","",
+		"CPU1_UPHY4_PRSNT1_L-I","",
+		"CPU0_UPHY4_PRSNT0_L-I","",
+		"","",
+		"I2C_RTC_ALERT_L-I","",
+		"FAN7_PRESENT_L-I","",
+		"FAN6_PRESENT_L-I","",
+		"FAN5_PRESENT_L-I","",
+		"FAN4_PRESENT_L-I","",
+		"FAN3_PRESENT_L-I","",
+		"FAN2_PRESENT_L-I","",
+		"IOBRD0_IOX_INT_L-I","",
+		"IOBRD1_PRSNT_L-I","",
+		"IOBRD0_PRSNT_L-I","",
+		"IOBRD1_PWR_GOOD-I","",
+		"IOBRD0_PWR_GOOD-I","",
+		"","",
+		"","",
+		"FAN_FAIL_IN_L-I","",
+		"","",
+		"","",
+		"","",
+		"PDB_CABLE_PRESENT_L-I","",
+		"","",
+		"CHASSIS_PWR_BRK_L-I","",
+		"","",
+		"IOBRD1_IOX_INT_L-I","",
+		"10GBE_SMBALRT_L-I","",
+		"PCIE_WAKE_L-I","",
+		"I2C_M21_ALERT_L-I","",
+		"I2C_M20_ALERT_L-I","",
+		"TRAY_FAST_SHDN_L-I","",
+		"UID_BTN_N-I","",
+		"PWR_BTN_L-I","",
+		"PSU_SMB_ALERT_L-I","",
+		"","",
+		"","",
+		"NODE_LOC_ID[0]-I","",
+		"NODE_LOC_ID[1]-I","",
+		"NODE_LOC_ID[2]-I","",
+		"NODE_LOC_ID[3]-I","",
+		"NODE_LOC_ID[4]-I","",
+		"NODE_LOC_ID[5]-I","",
+		"FAN10_PRESENT_L-I","",
+		"FAN9_PRESENT_L-I","",
+		"FAN8_PRESENT_L-I","",
+		"FPGA1_READY_HMC-I","",
+		"DP_HPD-I","",
+		"HMC_I2C3_FPGA_ALERT_L-I","",
+		"HMC_I2C2_FPGA_ALERT_L-I","",
+		"FPGA0_READY_HMC-I","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"LEAK_DETECT_ALERT_L-I","",
+		"MOD1_B2B_CABLE_PRESENT_L-I","",
+		"MOD1_CLINK_CABLE_PRESENT_L-I","",
+		"FAN11_PRESENT_L-I","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"RSVD_SGPIO_IN_CRC[0]","RSVD_SGPIO_O_CRC[7]",
+		"RSVD_SGPIO_IN_CRC[1]","RSVD_SGPIO_O_CRC[6]",
+		"RSVD_SGPIO_IN_CRC[2]","RSVD_SGPIO_O_CRC[5]",
+		"RSVD_SGPIO_IN_CRC[3]","RSVD_SGPIO_O_CRC[4]",
+		"RSVD_SGPIO_IN_CRC[4]","RSVD_SGPIO_O_CRC[3]",
+		"RSVD_SGPIO_IN_CRC[5]","RSVD_SGPIO_O_CRC[2]",
+		"RSVD_SGPIO_IN_CRC[6]","RSVD_SGPIO_O_CRC[1]",
+		"RSVD_SGPIO_IN_CRC[7]","RSVD_SGPIO_O_CRC[0]";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+// Enabling SOL
+&uart3 {
+	status = "okay";
+};
+
+// BMC Debug Console
+&uart5 {
+	status = "okay";
+};
+
+&uart_routing { };
+
+// I2C1, SSIF IPMI interface
+&i2c0 {
+	clock-frequency = <400000>;
+	status = "okay";
+	ssif-bmc@10 {
+		compatible = "ssif-bmc";
+		reg = <0x10>;
+	};
+};
+
+// I2C3
+// BMC_I2C0_FPGA - Primary FPGA
+&i2c2 {
+	clock-frequency = <400000>;
+	multi-master;
+	status = "okay";
+};
+
+// I2C5
+// RTC Driver
+// IO Expander
+&i2c4 {
+	clock-frequency = <400000>;
+	status = "okay";
+	// Module 0, Expander @0x21
+	exp4: gpio@21 {
+		compatible = "nxp,pca9555";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+		vcc-supply = <&reg_3v3_stby>;
+		gpio-line-names =
+			"RTC_MUX_SEL-O",
+			"PCI_MUX_SEL-O",
+			"TPM_MUX_SEL-O",
+			"FAN_MUX-SEL-O",
+			"SGMII_MUX_SEL-O",
+			"DP_MUX_SEL-O",
+			"UPHY3_USB_SEL-O",
+			"NCSI_MUX_SEL-O",
+			"BMC_PHY_RST-O",
+			"RTC_CLR_L-O",
+			"BMC_12V_CTRL-O",
+			"PS_RUN_IO0_PG-I",
+			"",
+			"",
+			"",
+			"";
+	};
+};
+
+// I2C6
+// Module 0/1 I2C MUX x3
+&i2c5 {
+	clock-frequency = <400000>;
+	multi-master;
+	status = "okay";
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&reg_3v3_stby>;
+
+		imux16: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux17: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			i2c-mux@74 {
+				compatible = "nxp,pca9546";
+				reg = <0x74>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				i2c-mux-idle-disconnect;
+				vdd-supply = <&reg_3v3_stby>;
+
+				i2c17mux0: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				i2c17mux1: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				i2c17mux2: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				i2c17mux3: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+			};
+		};
+
+		imux18: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux19: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9546";
+		reg = <0x72>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&reg_3v3_stby>;
+
+		imux20: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux21: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpio@20 {
+				compatible = "nxp,pca9555";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				vcc-supply = <&reg_3v3_stby>;
+				gpio-line-names =
+					"RST_CX_0_L-O",
+					"RST_CX_1_L-O",
+					"CX0_SSD0_PRSNT_L-I",
+					"CX1_SSD1_PRSNT_L-I",
+					"CX_BOOT_CMPLT_CX0-I",
+					"CX_BOOT_CMPLT_CX1-I",
+					"CX_TWARN_CX0_L-I",
+					"CX_TWARN_CX1_L-I",
+					"CX_OVT_SHDN_CX0-I",
+					"CX_OVT_SHDN_CX1-I",
+					"FNP_L_CX0-O",
+					"FNP_L_CX1-O",
+					"",
+					"MCU_GPIO-I",
+					"MCU_RST_N-O",
+					"MCU_RECOVERY_N-O";
+			};
+		};
+
+		imux22: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux23: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	i2c-mux@73 {
+		compatible = "nxp,pca9546";
+		reg = <0x73>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&reg_3v3_stby>;
+
+		imux24: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux25: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2c-mux@70 {
+				compatible = "nxp,pca9546";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				i2c-mux-idle-disconnect;
+				vdd-supply = <&reg_3v3_stby>;
+
+				i2c25mux0: i2c@0 {
+					reg = <0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+
+				i2c25mux1: i2c@1 {
+					reg = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+
+				i2c25mux2: i2c@2 {
+					reg = <2>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+
+				i2c25mux3: i2c@3 {
+					reg = <3>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+			};
+		};
+
+		imux26: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux27: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9546";
+		reg = <0x75>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&reg_3v3_stby>;
+
+		imux28: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux29: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2c-mux@74 {
+				compatible = "nxp,pca9546";
+				reg = <0x74>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				i2c-mux-idle-disconnect;
+				vdd-supply = <&reg_3v3_stby>;
+
+				i2c29mux0: i2c@0 {
+					reg = <0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+
+				i2c29mux1: i2c@1 {
+					reg = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+
+				i2c29mux2: i2c@2 {
+					reg = <2>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+
+				i2c29mux3: i2c@3 {
+					reg = <3>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+			};
+		};
+
+		imux30: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux31: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	i2c-mux@76 {
+		compatible = "nxp,pca9546";
+		reg = <0x76>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&reg_3v3_stby>;
+
+		imux32: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux33: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux34: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux35: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	i2c-mux@77 {
+		compatible = "nxp,pca9546";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&reg_3v3_stby>;
+
+		imux36: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux37: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux38: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux39: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+// I2C7
+// Module 0/1 Leak Sensors
+// Module 0/1 Fan Controllers
+&i2c6 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	pmic@12 {
+		compatible = "ti,lm5066i";
+		reg = <0x12>;
+		shunt-resistor-micro-ohms = <190>;
+	};
+
+	pmic@14 {
+		compatible = "ti,lm5066i";
+		reg = <0x14>;
+		shunt-resistor-micro-ohms = <190>;
+	};
+
+	pwm@20 {
+		compatible = "maxim,max31790";
+		reg = <0x20>;
+	};
+
+	pwm@23 {
+		compatible = "maxim,max31790";
+		reg = <0x23>;
+	};
+
+	pwm@2c {
+		compatible = "maxim,max31790";
+		reg = <0x2c>;
+	};
+
+	pwm@2f {
+		compatible = "maxim,max31790";
+		reg = <0x2f>;
+	};
+};
+
+// I2C9
+// M.2
+&i2c8 {
+	clock-frequency = <400000>;
+	multi-master;
+	status = "okay";
+};
+
+// I2C10
+// Module 0/1 IO Expanders
+&i2c9 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	// Module 0, Expander @0x20
+	exp0: gpio@20 {
+		compatible = "nxp,pca9555";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+		vcc-supply = <&reg_3v3_stby>;
+		gpio-line-names =
+			"FPGA_THERM_OVERT_L-I",
+			"FPGA_READY_BMC-I",
+			"HMC_BMC_DETECT-O",
+			"HMC_PGOOD-O",
+			"",
+			"BMC_STBY_CYCLE-O",
+			"FPGA_EROT_FATAL_ERROR_L-I",
+			"WP_HW_EXT_CTRL_L-O",
+			"EROT_FPGA_RST_L-O",
+			"FPGA_EROT_RECOVERY_L-O",
+			"BMC_EROT_FPGA_SPI_MUX_SEL-O",
+			"USB_HUB_RESET_L-O",
+			"NCSI_CS1_SEL-O",
+			"SGPIO_EN_L-O",
+			"B2B_IOEXP_INT_L-I",
+			"I2C_BUS_MUX_RESET_L-O";
+	};
+
+	// UT3.0b Expander @0x22
+	exp2: gpio@22 {
+		compatible = "nxp,pca9555";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+		vcc-supply = <&reg_3v3_stby>;
+		gpio-line-names =
+			"BMC1_FANCTRL_FAIL_L-I",
+			"IOEXP_BMC_RST_12V-O",
+			"NODE_RST_STBY_H-O",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"";
+	};
+
+	// UT3.0b Expander @0x23
+	exp3: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+		vcc-supply = <&reg_3v3_stby>;
+		gpio-line-names =
+			"PEXSW_FL_SPI_MUX_SEL-O",
+			"PEX_SW_FATAL_ERROR_3V3_L-I",
+			"IOEXP_PDB_NODE_EN_L-O",
+			"NODE_PWOK_ISO-I",
+			"BMC_FAN_PWR_EN-O",
+			"BMC_ETHERNET_INT-I",
+			"BMC_ENET_RST-O",
+			"IOEXP_BMC_RST_SENSE-O",
+			"BMC_ID-I",
+			"TPM_MUX_3V3_SEL_N-O",
+			"IOEXP_TPM_RST_N-O",
+			"TPM_DOWN_SPI_INT_L-I",
+			"PS_BRD_PGOOD-I",
+			"FP_BUTTON_POWER_N-I",
+			"FP_BUTTON_RESET_N-I",
+			"FP_LED_POWER_GPIOEXP_N-O";
+	};
+};
+
+// I2C11
+// BMC FRU EEPROM
+// BMC Temp Sensor
+&i2c10 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	// BMC FRU EEPROM - 256 bytes
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <8>;
+	};
+};
+
+// I2C12
+&i2c11 {
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+// I2C15
+// Module 1 UPHY3 SMBus
+&i2c14 {
+	clock-frequency = <100000>;
+	multi-master;
+	status = "okay";
+
+	//E1.S drive slot 0-3
+	i2c-mux@77 {
+		compatible = "nxp,pca9546";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&reg_3v3_stby>;
+
+		e1si2c0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		e1si2c1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		e1si2c2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		e1si2c3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
-- 
2.43.0

Re: [PATCH v8 2/2] ARM: dts: aspeed: Add NVIDIA GB200 UT3.0b board

[Andrew Jeffery]

Hi Donald,

Sorry for the delay.

On Fri, 2025-08-15 at 15:43 -0700, Donald Shannon wrote:
> This is an Aspeed AST2600 based unit testing platform for GB200.
> UT3.0b is different than nvidia-gb200nvl-bmc due to networking topology
> differences, additional gpio expanders, and voltage regulator gating
> some devices.
> 
> Reference to Ast2600 SOC [1].
> Reference to Blackwell GB200NVL Platform [2].
> 
> Link: https://www.aspeedtech.com/server_ast2600/ [1]
> Link: https://nvdam.widen.net/s/wwnsxrhm2w/blackwell-datasheet-3384703 [2]
> Signed-off-by: Donald Shannon <donalds@nvidia.com>
> ---
>  arch/arm/boot/dts/aspeed/Makefile             |    1 +
>  .../aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts  | 1030 +++++++++++++++++
>  2 files changed, 1031 insertions(+)
>  create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts
> 
> diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
> index aba7451ab749..37edc4625a9f 100644
> --- a/arch/arm/boot/dts/aspeed/Makefile
> +++ b/arch/arm/boot/dts/aspeed/Makefile
> 

*snip*

> +&gpio0 {
> +       gpio-line-names =
> +               /*A0-A7*/ "", "", "", "", "", "", "", "",
> +               /*B0-B7*/ "", "", "", "", "", "", "", "",
> +               /*C0-C7*/ "SGPIO_I2C_MUX_SEL-O", "", "", "", "", "", "", "",
> +               /*D0-D7*/ "", "", "", "UART1_MUX_SEL-O", "", "FPGA_PEX_RST_L-O", "", "",
> +               /*E0-E7*/ "RTL8221_PHY_RST_L-O", "RTL8211_PHY_INT_L-I", "", "UART3_MUX_SEL-O",
> +                                       "", "", "", "SGPIO_BMC_EN-O",
> +               /*F0-F7*/ "", "", "", "", "", "", "", "",
> +               /*G0-G7*/ "", "", "", "", "", "", "", "",
> +               /*H0-H7*/ "", "", "", "", "", "", "", "",
> +               /*I0-I7*/ "", "", "", "", "", "QSPI2_RST_L-O", "GLOBAL_WP_BMC-O", "BMC_DDR4_TEN-O",
> +               /*J0-J7*/ "", "", "", "", "", "", "", "",
> +               /*K0-K7*/ "", "", "", "", "", "", "", "",
> +               /*L0-L7*/ "", "", "", "", "", "", "", "",
> +               /*M0-M7*/ "PCIE_EP_RST_EN-O", "BMC_FRU_WP-O", "FPGA_RST_L-O", "STBY_POWER_EN-O",
> +                                       "STBY_POWER_PG-I", "PCIE_EP_RST_L-O", "", "",
> +               /*N0-N7*/ "", "", "", "", "", "", "", "",
> +               /*O0-O7*/ "", "", "", "", "", "", "", "",
> +               /*P0-P7*/ "", "", "", "", "", "", "", "",
> +               /*Q0-Q7*/ "", "", "", "", "", "", "", "",
> +               /*R0-R7*/ "", "", "", "", "", "", "", "",
> +               /*S0-S7*/ "", "", "", "", "", "", "", "",
> +               /*T0-T7*/ "", "", "", "", "", "", "", "",
> +               /*U0-U7*/ "", "", "", "", "", "", "", "",
> +               /*V0-V7*/ "AP_EROT_REQ-O", "EROT_AP_GNT-I", "", "","PCB_TEMP_ALERT-I", "","", "",
> +               /*W0-W7*/ "", "", "", "", "", "", "", "",
> +               /*X0-X7*/ "", "", "TPM_MUX_SEL-O", "", "", "", "", "",
> +               /*Y0-Y7*/ "", "", "", "EMMC_RST-O", "","", "", "",
> +               /*Z0-Z7*/ "BMC_READY-O","", "", "", "", "", "", "";
> +};
> +
> +&gpio1 {
> +       /* 36 1.8V GPIOs */
> +       gpio-line-names =
> +               /*A0-A7*/ "", "", "", "", "", "", "", "",
> +               /*B0-B7*/ "", "", "", "", "", "", "IO_EXPANDER_INT_L-I","",
> +               /*C0-C7*/ "", "", "", "", "", "", "", "",
> +               /*D0-D7*/ "", "", "", "", "", "", "SPI_HOST_TPM_RST_L-O", "SPI_BMC_FPGA_INT_L-I",
> +               /*E0-E7*/ "", "", "", "", "", "", "", "";
> +};
> +
> +&sgpiom0 {

So the style guide asks the referenced nodes to be ordered either
alphabetically, or in DTSI order[1] (which should be unit-address
order).

[1]: https://docs.kernel.org/devicetree/bindings/dts-coding-style.html#order-of-nodes

What we have to the quoted section above isn't in alphabetical order.
To this point it was DTSI order, but that breaks here too.

My preference is that nodes in the DTS referencing the DTSI are
alphabetical (as we can't see the unit address for ordering). Can you
please fix it?

You mention in your cover letter that ordering was addressed in v3 -
did we lose that along the way?

*snip*

> +
> +&uart_routing { };

Drop this?

Cheers,

Andrew