Re: sata_nv times out for BD-ROM iHOS104-08

["Cengiz Günay" <cgunay@emory.edu>]

[-- Attachment #1: Type: text/plain, Size: 499 bytes --]

On Sat, Feb 20, 2010 at 8:01 PM, Tejun Heo <tj@kernel.org> wrote:
> Hmmm... So, DRQ gets cleared?  That's strange.  When then the 18 extra
> bytes happen?  Can you please try this one?

It worked!

$ lsscsi
...
[4:0:0:0]    cd/dvd  ATAPI    iHOS104          WL08  /dev/sr0
...

I was able to read a regular DVD in the drive. According to dmesg the
negotiated speed was down to UDMA/33, so I am not sure about the
performance of the drive.

Full dmesg attached.

Thanks!
Cengiz

[-- Attachment #2: dmesg-sata_nv-swncq-polling-pio --]
[-- Type: application/octet-stream, Size: 77185 bytes --]

Linux version 2.6.32testing (root@salon) (gcc version 4.3.3 (Debian 4.3.3-10) ) #4 SMP PREEMPT Sun Feb 21 11:06:46 EST 2010
KERNEL supported cpus:
  Intel GenuineIntel
  AMD AuthenticAMD
  NSC Geode by NSC
  Cyrix CyrixInstead
  Centaur CentaurHauls
  Transmeta GenuineTMx86
  Transmeta TransmetaCPU
  UMC UMC UMC UMC
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009c400 (usable)
 BIOS-e820: 000000000009c400 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007fef0000 (usable)
 BIOS-e820: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
 BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
DMI 2.4 present.
Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
last_pfn = 0x7fef0 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
  00000-9FFFF write-back
  A0000-BFFFF uncachable
  C0000-CDFFF write-protect
  CE000-FFFFF uncachable
MTRR variable ranges enabled:
  0 base 000000000 mask F80000000 write-back
  1 base 07FF00000 mask FFFF00000 uncachable
  2 disabled
  3 disabled
  4 disabled
  5 disabled
  6 disabled
  7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-00000000377fe000
 0000000000 - 0000400000 page 4k
 0000400000 - 0037400000 page 2M
 0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 10000-15000
RAMDISK: 36bae000 - 37feff4b
Allocated new RAMDISK: 013e6000 - 02827f4b
Move RAMDISK from 0000000036bae000 - 0000000037feff4a to 013e6000 - 02827f4a
ACPI: RSDP 000f7900 00024 (v02 Nvidia)
ACPI: XSDT 7fef30c0 0004C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: FACP 7fefa600 000F4 (v03 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: DSDT 7fef3240 07354 (v01 NVIDIA ASUSACPI 00001000 MSFT 03000000)
ACPI: FACS 7fef0000 00040
ACPI: HPET 7fefa840 00038 (v01 Nvidia ASUSACPI 42302E31 AWRD 00000098)
ACPI: MCFG 7fefa8c0 0003C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: APIC 7fefa740 0008E (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: SSDT 7fefae20 0032C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: Local APIC address 0xfee00000
1158MB HIGHMEM available.
887MB LOWMEM available.
  mapped low ram: 0 - 377fe000
  low ram: 0 - 377fe000
  node 0 low ram: 00000000 - 377fe000
  node 0 bootmap 00011000 - 00017f00
(9 early reservations) ==> bootmem [0000000000 - 00377fe000]
  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
  #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
  #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
  #3 [0001000000 - 00013de7c4]    TEXT DATA BSS ==> [0001000000 - 00013de7c4]
  #4 [000009c400 - 0000100000]    BIOS reserved ==> [000009c400 - 0000100000]
  #5 [00013df000 - 00013e5149]              BRK ==> [00013df000 - 00013e5149]
  #6 [0000010000 - 0000011000]          PGTABLE ==> [0000010000 - 0000011000]
  #7 [00013e6000 - 0002827f4b]      NEW RAMDISK ==> [00013e6000 - 0002827f4b]
  #8 [0000011000 - 0000018000]          BOOTMAP ==> [0000011000 - 0000018000]
found SMP MP-table at [c00f5d50] f5d50
Zone PFN ranges:
  DMA      0x00000010 -> 0x00001000
  Normal   0x00001000 -> 0x000377fe
  HighMem  0x000377fe -> 0x0007fef0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0: 0x00000010 -> 0x0000009c
    0: 0x00000100 -> 0x0007fef0
On node 0 totalpages: 523900
free_area_init_node: node 0, pgdat c1324fc0, node_mem_map c2829200
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 3948 pages, LIFO batch:0
  Normal zone: 1744 pages used for memmap
  Normal zone: 221486 pages, LIFO batch:31
  HighMem zone: 2318 pages used for memmap
  HighMem zone: 294372 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x10de8201 base: 0xfeff0000
SMP: Allowing 4 CPUs, 2 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009c000 - 000000000009d000
PM: Registered nosave memory: 000000000009d000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 7ff00000 (gap: 7ff00000:60100000)
NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 11 pages/cpu @c3c00000 s23512 r0 d21544 u1048576
pcpu-alloc: s23512 r0 d21544 u1048576 alloc=1*4194304
pcpu-alloc: [0] 0 1 2 3 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 519806
Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32testing root=/dev/mapper/nvidia_ceebaiib1 ro
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Initializing HighMem for node 0 (000377fe:0007fef0)
Memory: 2052264k/2096064k available (2319k kernel code, 42156k reserved, 912k data, 404k init, 1186760k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff6b000 - 0xfffff000   ( 592 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
    lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
      .init : 0xc1329000 - 0xc138e000   ( 404 kB)
      .data : 0xc1243e41 - 0xc1328128   ( 912 kB)
      .text : 0xc1000000 - 0xc1243e41   (2319 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:384
Extended CMOS year: 2000
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
console [tty0] enabled
hpet clockevent registered
Fast TSC calibration using PIT
Detected 2133.591 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 4267.18 BogoMIPS (lpj=2133591)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20090903
..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found apic 0 pin 0) ...
....... works.
CPU0: Intel(R) Core(TM)2 CPU          6400  @ 2.13GHz stepping 06
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4266.83 BogoMIPS (lpj=2133415)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
CPU1: Intel(R) Core(TM)2 CPU          6400  @ 2.13GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (8534.01 BogoMIPS).
CPU0 attaching sched-domain:
 domain 0: span 0-1 level MC
  groups: 0 1
CPU1 attaching sched-domain:
 domain 0: span 0-1 level MC
  groups: 1 0
PM: Adding info for No Bus:platform
Time: 15:42:34  Date: 02/21/10
NET: Registered protocol family 16
PM: Adding info for No Bus:vtcon0
EISA bus registered
ACPI: bus type pci registered
PM: Adding info for No Bus:id
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
PM: Adding info for No Bus:default
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PM: Adding info for acpi:LNXSYSTM:00
PM: Adding info for acpi:LNXCPU:00
PM: Adding info for acpi:LNXCPU:01
PM: Adding info for acpi:LNXCPU:02
PM: Adding info for acpi:LNXCPU:03
PM: Adding info for acpi:LNXSYBUS:00
PM: Adding info for acpi:PNP0C0C:00
PM: Adding info for acpi:PNP0A08:00
PM: Adding info for acpi:PNP0C02:00
PM: Adding info for acpi:device:00
PM: Adding info for acpi:device:01
PM: Adding info for acpi:device:02
PM: Adding info for acpi:device:03
PM: Adding info for acpi:device:04
PM: Adding info for acpi:device:05
PM: Adding info for acpi:device:06
PM: Adding info for acpi:device:07
PM: Adding info for acpi:device:08
PM: Adding info for acpi:device:09
PM: Adding info for acpi:device:0a
PM: Adding info for acpi:device:0b
PM: Adding info for acpi:device:0c
PM: Adding info for acpi:device:0d
PM: Adding info for acpi:device:0e
PM: Adding info for acpi:device:0f
PM: Adding info for acpi:device:10
PM: Adding info for acpi:device:11
PM: Adding info for acpi:device:12
PM: Adding info for acpi:device:13
PM: Adding info for acpi:device:14
PM: Adding info for acpi:device:15
PM: Adding info for acpi:device:16
PM: Adding info for acpi:device:17
PM: Adding info for acpi:device:18
PM: Adding info for acpi:device:19
PM: Adding info for acpi:PNP0C02:01
PM: Adding info for acpi:PNP0000:00
PM: Adding info for acpi:PNP0200:00
PM: Adding info for acpi:PNP0100:00
PM: Adding info for acpi:PNP0103:00
PM: Adding info for acpi:PNP0B00:00
PM: Adding info for acpi:PNP0800:00
PM: Adding info for acpi:PNP0C04:00
PM: Adding info for acpi:device:1a
PM: Adding info for acpi:device:1b
PM: Adding info for acpi:device:1c
PM: Adding info for acpi:device:1d
PM: Adding info for acpi:device:1e
PM: Adding info for acpi:device:1f
PM: Adding info for acpi:NVRAIDBUS:00
PM: Adding info for acpi:ATK0110:00
PM: Adding info for acpi:PNP0C0F:00
PM: Adding info for acpi:PNP0C0F:01
PM: Adding info for acpi:PNP0C0F:02
PM: Adding info for acpi:PNP0C0F:03
PM: Adding info for acpi:PNP0C0F:04
PM: Adding info for acpi:PNP0C0F:05
PM: Adding info for acpi:PNP0C0F:06
PM: Adding info for acpi:PNP0C0F:07
PM: Adding info for acpi:PNP0C0F:08
PM: Adding info for acpi:PNP0C0F:09
PM: Adding info for acpi:PNP0C0F:0a
PM: Adding info for acpi:PNP0C0F:0b
PM: Adding info for acpi:PNP0C0F:0c
PM: Adding info for acpi:PNP0C0F:0d
PM: Adding info for acpi:PNP0C0F:0e
PM: Adding info for acpi:PNP0C0F:0f
PM: Adding info for acpi:PNP0C0F:10
PM: Adding info for acpi:PNP0C0F:11
PM: Adding info for acpi:PNP0C0F:12
PM: Adding info for acpi:PNP0C0F:13
PM: Adding info for acpi:PNP0C0F:14
PM: Adding info for acpi:PNP0C0F:15
PM: Adding info for acpi:PNP0C0F:16
PM: Adding info for acpi:PNP0C0F:17
PM: Adding info for acpi:PNP0C0F:18
PM: Adding info for acpi:PNP0C0F:19
PM: Adding info for acpi:PNP0C0F:1a
PM: Adding info for acpi:PNP0C0F:1b
PM: Adding info for acpi:PNP0C0F:1c
PM: Adding info for acpi:PNP0C0F:1d
PM: Adding info for acpi:PNP0C0F:1e
PM: Adding info for acpi:PNP0C0F:1f
PM: Adding info for acpi:PNP0C0F:20
PM: Adding info for acpi:PNP0C0F:21
PM: Adding info for acpi:PNP0C0F:22
PM: Adding info for acpi:PNP0C0F:23
PM: Adding info for acpi:PNP0C0F:24
PM: Adding info for acpi:PNP0C0F:25
PM: Adding info for acpi:PNP0C0F:26
PM: Adding info for acpi:PNP0C0F:27
PM: Adding info for acpi:PNP0C0F:28
PM: Adding info for acpi:PNP0C02:02
PM: Adding info for acpi:PNP0C01:00
PM: Adding info for acpi:LNXTHERM:00
PM: Adding info for acpi:PNP0C0B:00
PM: Adding info for acpi:LNXTHERM:01
PM: Adding info for acpi:LNXPWRBN:00
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
PM: Adding info for No Bus:pci0000:00
PM: Adding info for No Bus:0000:00
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:05.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:05.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:07.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:07.0: PME# disabled
pci 0000:00:0a.1: reg 20 io port: [0x5000-0x503f]
pci 0000:00:0a.1: reg 24 io port: [0x5100-0x513f]
pci 0000:00:0a.1: PME# supported from D3hot D3cold
pci 0000:00:0a.1: PME# disabled
pci 0000:00:0b.0: reg 10 32bit mmio: [0xd5006000-0xd5006fff]
pci 0000:00:0b.0: supports D1 D2
pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.0: PME# disabled
pci 0000:00:0b.1: reg 10 32bit mmio: [0xd5007000-0xd50070ff]
pci 0000:00:0b.1: supports D1 D2
pci 0000:00:0b.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.1: PME# disabled
pci 0000:00:0d.0: reg 20 io port: [0xf000-0xf00f]
pci 0000:00:0e.0: reg 10 io port: [0x9f0-0x9f7]
pci 0000:00:0e.0: reg 14 io port: [0xbf0-0xbf3]
pci 0000:00:0e.0: reg 18 io port: [0x970-0x977]
pci 0000:00:0e.0: reg 1c io port: [0xb70-0xb73]
pci 0000:00:0e.0: reg 20 io port: [0xd400-0xd40f]
pci 0000:00:0e.0: reg 24 32bit mmio: [0xd5004000-0xd5004fff]
pci 0000:00:0f.0: reg 10 io port: [0x9e0-0x9e7]
pci 0000:00:0f.0: reg 14 io port: [0xbe0-0xbe3]
pci 0000:00:0f.0: reg 18 io port: [0x960-0x967]
pci 0000:00:0f.0: reg 1c io port: [0xb60-0xb63]
pci 0000:00:0f.0: reg 20 io port: [0xe800-0xe80f]
pci 0000:00:0f.0: reg 24 32bit mmio: [0xd5005000-0xd5005fff]
pci 0000:00:10.1: reg 10 32bit mmio: [0xd5000000-0xd5003fff]
pci 0000:00:10.1: PME# supported from D3hot D3cold
pci 0000:00:10.1: PME# disabled
pci 0000:01:00.0: reg 10 32bit mmio: [0xd0000000-0xd0ffffff]
pci 0000:01:00.0: reg 14 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xd1000000-0xd1ffffff]
pci 0000:01:00.0: reg 24 io port: [0xa000-0xa07f]
pci 0000:01:00.0: reg 30 32bit mmio pref: [0xd2000000-0xd201ffff]
pci 0000:00:02.0: bridge io port: [0xa000-0xafff]
pci 0000:00:02.0: bridge 32bit mmio: [0xd0000000-0xd2ffffff]
pci 0000:00:02.0: bridge 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:06:06.0: reg 10 32bit mmio: [0xd4001000-0xd40017ff]
pci 0000:06:06.0: reg 14 io port: [0xb000-0xb07f]
pci 0000:06:06.0: supports D2
pci 0000:06:06.0: PME# supported from D2 D3hot D3cold
pci 0000:06:06.0: PME# disabled
pci 0000:06:07.0: reg 10 io port: [0xb400-0xb4ff]
pci 0000:06:07.0: reg 14 32bit mmio: [0xd4000000-0xd40000ff]
pci 0000:06:07.0: reg 30 32bit mmio pref: [0xd3000000-0xd301ffff]
pci 0000:06:07.0: supports D1 D2
pci 0000:06:07.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:06:07.0: PME# disabled
pci 0000:00:10.0: transparent bridge
pci 0000:00:10.0: bridge io port: [0xb000-0xbfff]
pci 0000:00:10.0: bridge 32bit mmio: [0xd3000000-0xd4ffffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
PM: Adding info for pci:0000:00:00.0
PM: Adding info for pci:0000:00:00.1
PM: Adding info for pci:0000:00:00.2
PM: Adding info for pci:0000:00:00.3
PM: Adding info for pci:0000:00:00.4
PM: Adding info for pci:0000:00:01.0
PM: Adding info for pci:0000:00:01.1
PM: Adding info for pci:0000:00:01.2
PM: Adding info for pci:0000:00:01.3
PM: Adding info for pci:0000:00:01.4
PM: Adding info for pci:0000:00:01.5
PM: Adding info for pci:0000:00:01.6
PM: Adding info for pci:0000:00:02.0
PM: Adding info for pci:0000:00:04.0
PM: Adding info for pci:0000:00:05.0
PM: Adding info for pci:0000:00:06.0
PM: Adding info for pci:0000:00:07.0
PM: Adding info for pci:0000:00:09.0
PM: Adding info for pci:0000:00:0a.0
PM: Adding info for pci:0000:00:0a.1
PM: Adding info for pci:0000:00:0a.2
PM: Adding info for pci:0000:00:0b.0
PM: Adding info for pci:0000:00:0b.1
PM: Adding info for pci:0000:00:0d.0
PM: Adding info for pci:0000:00:0e.0
PM: Adding info for pci:0000:00:0f.0
PM: Adding info for pci:0000:00:10.0
PM: Adding info for pci:0000:00:10.1
PM: Adding info for pci:0000:01:00.0
PM: Adding info for No Bus:0000:01
PM: Adding info for No Bus:0000:02
PM: Adding info for No Bus:0000:03
PM: Adding info for No Bus:0000:04
PM: Adding info for No Bus:0000:05
PM: Adding info for pci:0000:06:06.0
PM: Adding info for pci:0000:06:07.0
PM: Adding info for No Bus:0000:06
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
PM: Adding info for No Bus:vga_arbiter
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
PCI: Using ACPI for IRQ routing
PM: Adding info for No Bus:lo
hpet0: at MMIO 0xfeff0000, IRQs 2, 8, 31
hpet0: 3 comparators, 32-bit 25.000000 MHz counter
Switching to clocksource tsc
pnp: PnP ACPI init
PM: Adding info for No Bus:pnp0
ACPI: bus type pnp registered
PM: Adding info for pnp:00:00
PM: Adding info for pnp:00:01
PM: Adding info for pnp:00:02
PM: Adding info for pnp:00:03
PM: Adding info for pnp:00:04
PM: Adding info for pnp:00:05
PM: Adding info for pnp:00:06
PM: Adding info for pnp:00:07
PM: Adding info for pnp:00:08
PM: Adding info for pnp:00:09
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
system 00:01: ioport range 0x4000-0x407f has been reserved
system 00:01: ioport range 0x4080-0x40ff has been reserved
system 00:01: ioport range 0x4400-0x447f has been reserved
system 00:01: ioport range 0x4480-0x44ff has been reserved
system 00:01: ioport range 0x4800-0x487f has been reserved
system 00:01: ioport range 0x4880-0x48ff has been reserved
system 00:02: ioport range 0x4d0-0x4d1 has been reserved
system 00:02: ioport range 0x800-0x87f has been reserved
system 00:02: ioport range 0x290-0x297 has been reserved
system 00:02: ioport range 0x880-0x88f has been reserved
system 00:08: iomem range 0xe0000000-0xefffffff has been reserved
system 00:09: iomem range 0xdbc00-0xdbfff has been reserved
system 00:09: iomem range 0xf0000-0xf7fff could not be reserved
system 00:09: iomem range 0xf8000-0xfbfff could not be reserved
system 00:09: iomem range 0xfc000-0xfffff could not be reserved
system 00:09: iomem range 0xfeff0000-0xfeff00ff has been reserved
system 00:09: iomem range 0x7fef0000-0x7fefffff could not be reserved
system 00:09: iomem range 0xffff0000-0xffffffff has been reserved
system 00:09: iomem range 0x0-0x9ffff could not be reserved
system 00:09: iomem range 0x100000-0x7feeffff could not be reserved
system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:09: iomem range 0xfeff0000-0xfeff03ff could not be reserved
PM: Adding info for No Bus:mem
PM: Adding info for No Bus:kmem
PM: Adding info for No Bus:null
PM: Adding info for No Bus:port
PM: Adding info for No Bus:zero
PM: Adding info for No Bus:full
PM: Adding info for No Bus:random
PM: Adding info for No Bus:urandom
PM: Adding info for No Bus:kmsg
pci 0000:06:07.0: BAR 6: address space collision on of device [0xd3000000-0xd301ffff]
pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
pci 0000:00:02.0:   IO window: 0xa000-0xafff
pci 0000:00:02.0:   MEM window: 0xd0000000-0xd2ffffff
pci 0000:00:02.0:   PREFETCH window: 0x000000c0000000-0x000000cfffffff
pci 0000:00:04.0: PCI bridge, secondary bus 0000:02
pci 0000:00:04.0:   IO window: disabled
pci 0000:00:04.0:   MEM window: disabled
pci 0000:00:04.0:   PREFETCH window: disabled
pci 0000:00:05.0: PCI bridge, secondary bus 0000:03
pci 0000:00:05.0:   IO window: disabled
pci 0000:00:05.0:   MEM window: disabled
pci 0000:00:05.0:   PREFETCH window: disabled
pci 0000:00:06.0: PCI bridge, secondary bus 0000:04
pci 0000:00:06.0:   IO window: disabled
pci 0000:00:06.0:   MEM window: disabled
pci 0000:00:06.0:   PREFETCH window: disabled
pci 0000:00:07.0: PCI bridge, secondary bus 0000:05
pci 0000:00:07.0:   IO window: disabled
pci 0000:00:07.0:   MEM window: disabled
pci 0000:00:07.0:   PREFETCH window: disabled
pci 0000:00:10.0: PCI bridge, secondary bus 0000:06
pci 0000:00:10.0:   IO window: 0xb000-0xbfff
pci 0000:00:10.0:   MEM window: 0xd3000000-0xd4ffffff
pci 0000:00:10.0:   PREFETCH window: 0x80000000-0x800fffff
pci 0000:00:02.0: setting latency timer to 64
pci 0000:00:04.0: setting latency timer to 64
pci 0000:00:05.0: setting latency timer to 64
pci 0000:00:06.0: setting latency timer to 64
pci 0000:00:07.0: setting latency timer to 64
pci 0000:00:10.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io:  [0xa000-0xafff]
pci_bus 0000:01: resource 1 mem: [0xd0000000-0xd2ffffff]
pci_bus 0000:01: resource 2 pref mem [0xc0000000-0xcfffffff]
pci_bus 0000:06: resource 0 io:  [0xb000-0xbfff]
pci_bus 0000:06: resource 1 mem: [0xd3000000-0xd4ffffff]
pci_bus 0000:06: resource 2 pref mem [0x80000000-0x800fffff]
pci_bus 0000:06: resource 3 io:  [0x00-0xffff]
pci_bus 0000:06: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
pci 0000:01:00.0: Boot video device
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 20743k freed
PM: Adding info for No Bus:mcelog
PM: Adding info for No Bus:msr0
PM: Adding info for No Bus:msr1
PM: Adding info for platform:pcspkr
PM: Adding info for No Bus:snapshot
highmem bounce pool size: 64 pages
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 1733
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
pcieport 0000:00:02.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:02.0:pcie08
pcieport 0000:00:04.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:04.0:pcie08
pcieport 0000:00:05.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:05.0:pcie08
pcieport 0000:00:06.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:06.0:pcie08
pcieport 0000:00:07.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:07.0:pcie08
PM: Adding info for No Bus:pnp1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PM: Adding info for No Bus:tty
PM: Adding info for No Bus:console
PM: Adding info for No Bus:tty0
PM: Adding info for No Bus:vcs
PM: Adding info for No Bus:vcsa
PM: Adding info for No Bus:vcs1
PM: Adding info for No Bus:vcsa1
PM: Adding info for No Bus:tty1
PM: Adding info for No Bus:tty2
PM: Adding info for No Bus:tty3
PM: Adding info for No Bus:tty4
PM: Adding info for No Bus:tty5
PM: Adding info for No Bus:tty6
PM: Adding info for No Bus:tty7
PM: Adding info for No Bus:tty8
PM: Adding info for No Bus:tty9
PM: Adding info for No Bus:tty10
PM: Adding info for No Bus:tty11
PM: Adding info for No Bus:tty12
PM: Adding info for No Bus:tty13
PM: Adding info for No Bus:tty14
PM: Adding info for No Bus:tty15
PM: Adding info for No Bus:tty16
PM: Adding info for No Bus:tty17
PM: Adding info for No Bus:tty18
PM: Adding info for No Bus:tty19
PM: Adding info for No Bus:tty20
PM: Adding info for No Bus:tty21
PM: Adding info for No Bus:tty22
PM: Adding info for No Bus:tty23
PM: Adding info for No Bus:tty24
PM: Adding info for No Bus:tty25
PM: Adding info for No Bus:tty26
PM: Adding info for No Bus:tty27
PM: Adding info for No Bus:tty28
PM: Adding info for No Bus:tty29
PM: Adding info for No Bus:tty30
PM: Adding info for No Bus:tty31
PM: Adding info for No Bus:tty32
PM: Adding info for No Bus:tty33
PM: Adding info for No Bus:tty34
PM: Adding info for No Bus:tty35
PM: Adding info for No Bus:tty36
PM: Adding info for No Bus:tty37
PM: Adding info for No Bus:tty38
PM: Adding info for No Bus:tty39
PM: Adding info for No Bus:tty40
PM: Adding info for No Bus:tty41
PM: Adding info for No Bus:tty42
PM: Adding info for No Bus:tty43
PM: Adding info for No Bus:tty44
PM: Adding info for No Bus:tty45
PM: Adding info for No Bus:tty46
PM: Adding info for No Bus:tty47
PM: Adding info for No Bus:tty48
PM: Adding info for No Bus:tty49
PM: Adding info for No Bus:tty50
PM: Adding info for No Bus:tty51
PM: Adding info for No Bus:tty52
PM: Adding info for No Bus:tty53
PM: Adding info for No Bus:tty54
PM: Adding info for No Bus:tty55
PM: Adding info for No Bus:tty56
PM: Adding info for No Bus:tty57
PM: Adding info for No Bus:tty58
PM: Adding info for No Bus:tty59
PM: Adding info for No Bus:tty60
PM: Adding info for No Bus:tty61
PM: Adding info for No Bus:tty62
PM: Adding info for No Bus:tty63
PM: Adding info for No Bus:ptmx
PM: Adding info for No Bus:hpet
PM: Adding info for No Bus:isa
PM: Adding info for No Bus:ram0
PM: Adding info for No Bus:1:0
PM: Adding info for No Bus:ram1
PM: Adding info for No Bus:1:1
PM: Adding info for No Bus:ram2
PM: Adding info for No Bus:1:2
PM: Adding info for No Bus:ram3
PM: Adding info for No Bus:1:3
PM: Adding info for No Bus:ram4
PM: Adding info for No Bus:1:4
PM: Adding info for No Bus:ram5
PM: Adding info for No Bus:1:5
PM: Adding info for No Bus:ram6
PM: Adding info for No Bus:1:6
PM: Adding info for No Bus:ram7
PM: Adding info for No Bus:1:7
PM: Adding info for No Bus:ram8
PM: Adding info for No Bus:1:8
PM: Adding info for No Bus:ram9
PM: Adding info for No Bus:1:9
PM: Adding info for No Bus:ram10
PM: Adding info for No Bus:1:10
PM: Adding info for No Bus:ram11
PM: Adding info for No Bus:1:11
PM: Adding info for No Bus:ram12
PM: Adding info for No Bus:1:12
PM: Adding info for No Bus:ram13
PM: Adding info for No Bus:1:13
PM: Adding info for No Bus:ram14
PM: Adding info for No Bus:1:14
PM: Adding info for No Bus:ram15
PM: Adding info for No Bus:1:15
brd: module loaded
PNP: No PS/2 controller found. Probing ports directly.
PM: Adding info for platform:i8042
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
PM: Adding info for serio:serio0
PM: Adding info for serio:serio1
PM: Adding info for No Bus:mice
PM: Adding info for No Bus:psaux
mice: PS/2 mouse device common for all mice
PM: Adding info for platform:eisa.0
EISA: Probing bus 0 at eisa.0
PM: Removing info for platform:eisa.0
cpuidle: using governor ladder
TCP cubic registered
Using IPI No-Shortcut mode
PM: Adding info for No Bus:cpu_dma_latency
PM: Adding info for No Bus:network_latency
PM: Adding info for No Bus:network_throughput
PM: Checking image partition /dev/hda6
PM: Resume from disk failed.
  Magic number: 14:826:740
Freeing unused kernel memory: 404k freed
NET: Registered protocol family 1
PM: Adding info for No Bus:cooling_device0
fan PNP0C0B:00: registered as cooling_device0
ACPI: Fan [FAN] (on)
PM: Adding info for No Bus:thermal_zone0
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (40 C)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Uniform Multi-Platform E-IDE driver
SCSI subsystem initialized
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ohci_hcd 0000:00:0b.0: PCI INT A -> Link[APCF] -> GSI 23 (level, low) -> IRQ 23
ohci_hcd 0000:00:0b.0: setting latency timer to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0b.0: created debug files
ohci_hcd 0000:00:0b.0: supports USB remote wakeup
ohci_hcd 0000:00:0b.0: irq 23, io mem 0xd5006000
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
ehci_hcd: block sizes: qh 60 qtd 96 itd 160 sitd 96
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
r8169 0000:06:07.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17
r8169 0000:06:07.0: no PCI Express capability
PM: Adding info for No Bus:eth0
eth0: RTL8169sb/8110sb at 0xf8b2e000, 00:14:d1:1a:ac:15, XID 10000000 IRQ 17
udev: renamed network interface eth0 to eth1
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ohci1394 0000:06:06.0: PCI INT A -> Link[APC1] -> GSI 16 (level, low) -> IRQ 16
PM: Adding info for ieee1394:fw-host0
PM: Adding info for No Bus:fw-host0
libata version 3.00 loaded.
ohci_hcd 0000:00:0b.0: OHCI controller state
ohci_hcd 0000:00:0b.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:0b.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:0b.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:0b.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0000:00:0b.0: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:0b.0: hcca frame #0003
ohci_hcd 0000:00:0b.0: roothub.a 01000208 POTPGT=1 NPS NDP=8(8)
ohci_hcd 0000:00:0b.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:0b.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:0b.0: roothub.portstatus [0] 0x00010301 CSC LSDA PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [1] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [2] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [3] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [4] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [5] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [6] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [7] 0x00000100 PPS
usb usb1: default language 0x0409
usb usb1: udev 1, busnum 1, minor = 0
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32testing ohci_hcd
usb usb1: SerialNumber: 0000:00:0b.0
PM: Adding info for usb:usb1
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
PM: Adding info for usb:1-0:1.0
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: trying to enable port power on non-switchable hub
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.1
drivers/usb/core/inode.c: creating file '001'
PM: Adding info for No Bus:ep_00
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
ehci_hcd 0000:00:0b.1: PCI INT B -> Link[APCL] -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:0b.1: setting latency timer to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
drivers/usb/core/inode.c: creating file '002'
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:0b.1: reset hcs_params 0x101888 dbg=1 cc=1 pcc=8 !ppc ports=8
ehci_hcd 0000:00:0b.1: reset portroute 0 0 0 0 0 0 0 0 
ehci_hcd 0000:00:0b.1: reset hcc_params a086 caching frame 256/512/1024 park
ehci_hcd 0000:00:0b.1: park 0
ehci_hcd 0000:00:0b.1: debug port 1
ehci_hcd 0000:00:0b.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0b.1: cache line size of 32 is not supported
ehci_hcd 0000:00:0b.1: supports USB remote wakeup
ehci_hcd 0000:00:0b.1: irq 22, io mem 0xd5007000
ehci_hcd 0000:00:0b.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0b.1: init command 010009 (park)=0 ithresh=1 period=256 RUN
usb usb1: uevent
usb usb1: uevent
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16]  MMIO=[d4001000-d40017ff]  Max Packet=[2]  IR/IT contexts=[4/8]
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
usb usb2: default language 0x0409
usb usb2: udev 1, busnum 2, minor = 128
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.32testing ehci_hcd
usb usb2: SerialNumber: 0000:00:0b.1
PM: Adding info for usb:usb2
usb usb2: uevent
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
PM: Adding info for usb:2-0:1.0
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 20ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: trying to enable port power on non-switchable hub
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.1
drivers/usb/core/inode.c: creating file '001'
PM: Adding info for No Bus:ep_00
amd74xx 0000:00:0d.0: UDMA133 controller
amd74xx 0000:00:0d.0: IDE controller (0x10de:0x0265 rev 0xa1)
amd74xx 0000:00:0d.0: IDE port disabled
amd74xx 0000:00:0d.0: BIOS didn't set cable bits correctly. Enabling workaround.
amd74xx 0000:00:0d.0: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xf008-0xf00f
Probing IDE interface ide0...
ohci1394: fw-host0: Serial EEPROM has suspicious values, attempting to set max_packet_size to 512 bytes
usb usb2: uevent
usb usb2: uevent
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010300 CSC LSDA PPS
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [5] = 0x00010100 CSC PPS
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 2: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 3: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 6: status 0501 change 0001
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 8 chg 004e evt 0000
hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:0b.1: port 2 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
usb 2-2: new high speed USB device using ehci_hcd and address 3
ehci_hcd 0000:00:0b.1: port 2 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
usb 2-2: default language 0x0409
ehci_hcd 0000:00:0b.1: detected XactErr len 0/8 retry 1
usb 2-2: udev 3, busnum 2, minor = 130
usb 2-2: New USB device found, idVendor=058f, idProduct=6362
usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-2: Product: Mass Storage Device
usb 2-2: Manufacturer: Generic
usb 2-2: SerialNumber: 058F312D81B
PM: Adding info for usb:2-2
usb 2-2: uevent
usb 2-2: usb_probe_device
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: adding 2-2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-2:1.0
usb 2-2:1.0: uevent
PM: Adding info for No Bus:ep_01
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev2.3
drivers/usb/core/inode.c: creating file '003'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: port 3, status 0501, change 0000, 480 Mb/s
usb 2-2: uevent
usb 2-2: uevent
Initializing USB Mass Storage driver...
usb-storage 2-2:1.0: usb_probe_interface
usb-storage 2-2:1.0: usb_probe_interface - got id
scsi0 : SCSI emulation for USB Mass Storage devices
PM: Adding info for scsi:host0
PM: Adding info for No Bus:host0
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
ehci_hcd 0000:00:0b.1: port 3 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
usb 2-3: new high speed USB device using ehci_hcd and address 4
ehci_hcd 0000:00:0b.1: port 3 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
hda: PIONEER DVD-RW DVR-111D, ATAPI CD/DVD-ROM drive
usb 2-3: default language 0x0409
usb 2-3: udev 4, busnum 2, minor = 131
usb 2-3: New USB device found, idVendor=05e3, idProduct=0605
usb 2-3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-3: Product: USB2.0 Hub
PM: Adding info for usb:2-3
usb 2-3: uevent
usb 2-3: usb_probe_device
usb 2-3: configuration #1 chosen from 1 choice
usb 2-3: adding 2-3:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3:1.0
usb 2-3:1.0: uevent
hub 2-3:1.0: usb_probe_interface
hub 2-3:1.0: usb_probe_interface - got id
hub 2-3:1.0: USB hub found
hub 2-3:1.0: 4 ports detected
usb 2-3: uevent
hub 2-3:1.0: standalone hub
hub 2-3:1.0: individual port power switching
hub 2-3:1.0: individual port over-current protection
hub 2-3:1.0: Single TT
hub 2-3:1.0: TT requires at most 32 FS bit times (2664 ns)
hub 2-3:1.0: Port indicators are supported
hub 2-3:1.0: power on to power good time: 100ms
hub 2-3:1.0: local power source is good
hub 2-3:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.4
drivers/usb/core/inode.c: creating file '004'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: port 6, status 0501, change 0000, 480 Mb/s
usb 2-3: uevent
ehci_hcd 0000:00:0b.1: port 6 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
hub 2-3:1.0: port 1: status 0101 change 0001
usb 2-6: new high speed USB device using ehci_hcd and address 5
ehci_hcd 0000:00:0b.1: port 6 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 2-3: link qh256-0001/c1d96b40 start 1 [1/0 us]
usb 2-6: udev 5, busnum 2, minor = 132
usb 2-6: New USB device found, idVendor=0409, idProduct=0059
usb 2-6: New USB device strings: Mfr=0, Product=0, SerialNumber=0
PM: Adding info for usb:2-6
usb 2-6: uevent
usb 2-6: usb_probe_device
usb 2-6: configuration #1 chosen from 1 choice
usb 2-6: adding 2-6:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6:1.0
usb 2-6:1.0: uevent
hub 2-6:1.0: usb_probe_interface
hub 2-6:1.0: usb_probe_interface - got id
hub 2-6:1.0: USB hub found
hub 2-6:1.0: 4 ports detected
hub 2-6:1.0: standalone hub
hub 2-6:1.0: individual port power switching
hub 2-6:1.0: individual port over-current protection
hub 2-6:1.0: Single TT
hub 2-6:1.0: TT requires at most 16 FS bit times (1332 ns)
hub 2-6:1.0: Port indicators are supported
hub 2-6:1.0: power on to power good time: 100ms
usb 2-6: uevent
hub 2-6:1.0: local power source is good
hub 2-6:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.5
usb 2-6: uevent
drivers/usb/core/inode.c: creating file '005'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
hub 2-6:1.0: port 1: status 0301 change 0001
hub 2-6:1.0: port 3: status 0101 change 0001
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-3:1.0: state 7 ports 4 chg 0002 evt 0000
hub 2-3:1.0: port 1, status 0101, change 0000, 12 Mb/s
usb 2-6: link qh256-0001/c1d96cc0 start 2 [1/0 us]
usb 2-3.1: new high speed USB device using ehci_hcd and address 6
usb 2-3.1: udev 6, busnum 2, minor = 133
usb 2-3.1: New USB device found, idVendor=0409, idProduct=0059
usb 2-3.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
PM: Adding info for usb:2-3.1
usb 2-3.1: uevent
usb 2-3.1: usb_probe_device
usb 2-3.1: configuration #1 chosen from 1 choice
usb 2-3.1: adding 2-3.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1:1.0
usb 2-3.1:1.0: uevent
hub 2-3.1:1.0: usb_probe_interface
hub 2-3.1:1.0: usb_probe_interface - got id
hub 2-3.1:1.0: USB hub found
hub 2-3.1:1.0: 4 ports detected
hub 2-3.1:1.0: standalone hub
hub 2-3.1:1.0: individual port power switching
hub 2-3.1:1.0: individual port over-current protection
hub 2-3.1:1.0: Single TT
hub 2-3.1:1.0: TT requires at most 16 FS bit times (1332 ns)
hub 2-3.1:1.0: Port indicators are supported
hub 2-3.1:1.0: power on to power good time: 100ms
hub 2-3.1:1.0: local power source is good
hub 2-3.1:1.0: enabling power on all ports
usb 2-3.1: uevent
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.6
drivers/usb/core/inode.c: creating file '006'
PM: Adding info for No Bus:ep_00
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
hub 1-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
usb 2-3.1: uevent
PM: Adding info for ieee1394:001106000000bd66
PM: Adding info for No Bus:001106000000bd66
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[001106000000bd66]
PM: Adding info for ieee1394:001a66fffee31809
PM: Adding info for No Bus:001a66fffee31809
ieee1394: Node added: ID:BUS[0-01:1023]  GUID[001a66fffee31809]
PM: Adding info for ieee1394:001a66fffee31809-0
PM: Adding info for No Bus:001a66fffee31809-0
PM: Adding info for ieee1394:001a66fffee31809-1
PM: Adding info for No Bus:001a66fffee31809-1
PM: Adding info for No Bus:ide0
PM: Adding info for No Bus:ide0
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/66 mode selected
ide0 at 0x170-0x177,0x376 on irq 15
PM: Adding info for ide:0.0
sata_nv 0000:00:0e.0: version 3.5
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:0e.0: Using SWNCQ mode
sata_nv 0000:00:0e.0: setting latency timer to 64
scsi1 : sata_nv
PM: Adding info for scsi:host1
PM: Adding info for No Bus:host1
scsi2 : sata_nv
PM: Adding info for scsi:host2
PM: Adding info for No Bus:host2
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 21
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 21
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
sata_nv 0000:00:0f.0: PCI INT A -> Link[APSJ] -> GSI 20 (level, low) -> IRQ 20
sata_nv 0000:00:0f.0: Using SWNCQ mode
sata_nv 0000:00:0f.0: setting latency timer to 64
scsi3 : sata_nv
PM: Adding info for scsi:host3
PM: Adding info for No Bus:host3
scsi4 : sata_nv
PM: Adding info for scsi:host4
PM: Adding info for No Bus:host4
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 20
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 20
hub 2-3.1:1.0: port 1: status 0301 change 0001
hub 2-3.1:1.0: port 2: status 0101 change 0001
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
hub 2-6:1.0: state 7 ports 4 chg 000a evt 0000
hub 2-6:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
hub 2-6:1.0: port 1 not reset yet, waiting 10ms
usb 2-6.1: new low speed USB device using ehci_hcd and address 7
hub 2-6:1.0: port 1 not reset yet, waiting 10ms
usb 2-3.1: link qh256-0001/c1dcd640 start 3 [1/0 us]
usb 2-6.1: skipped 1 descriptor after interface
usb 2-6.1: default language 0x0409
usb 2-6.1: udev 7, busnum 2, minor = 134
usb 2-6.1: New USB device found, idVendor=2222, idProduct=3100
usb 2-6.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-6.1: Product: Macally ECOMouse 
usb 2-6.1: Manufacturer: Macally Peripherals 
PM: Adding info for usb:2-6.1
usb 2-6.1: uevent
usb 2-6.1: usb_probe_device
usb 2-6.1: configuration #1 chosen from 1 choice
usb 2-6.1: adding 2-6.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.1:1.0
usb 2-6.1:1.0: uevent
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.7
drivers/usb/core/inode.c: creating file '007'
PM: Adding info for No Bus:ep_00
usb 2-6.1: uevent
hub 2-6:1.0: port 3, status 0101, change 0000, 12 Mb/s
usb 2-6.1: uevent
usbcore: registered new interface driver hiddev
usbhid 2-6.1:1.0: usb_probe_interface
usbhid 2-6.1:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:3100.0001
PM: Adding info for No Bus:input0
input: Macally Peripherals  Macally ECOMouse  as /devices/pci0000:00/0000:00:0b.1/usb2/2-6/2-6.1/2-6.1:1.0/input/input0
PM: Adding info for No Bus:mouse0
generic-usb 0003:2222:3100.0001: input: USB HID v1.00 Mouse [Macally Peripherals  Macally ECOMouse ] on usb-0000:00:0b.1-6.1/input0
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
hub 2-6:1.0: port 3 not reset yet, waiting 10ms
usb 2-6.3: new full speed USB device using ehci_hcd and address 8
hub 2-6:1.0: port 3 not reset yet, waiting 10ms
ata3: SATA link down (SStatus 0 SControl 300)
usb 2-6.3: ep0 maxpacket = 8
usb 2-6.3: default language 0x0409
usb 2-6.3: udev 8, busnum 2, minor = 135
usb 2-6.3: New USB device found, idVendor=05e3, idProduct=0604
usb 2-6.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-6.3: Product: USB Hub
PM: Adding info for usb:2-6.3
usb 2-6.3: uevent
usb 2-6.3: usb_probe_device
usb 2-6.3: configuration #1 chosen from 1 choice
usb 2-6.3: adding 2-6.3:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.3:1.0
usb 2-6.3:1.0: uevent
hub 2-6.3:1.0: usb_probe_interface
hub 2-6.3:1.0: usb_probe_interface - got id
hub 2-6.3:1.0: USB hub found
usb 2-6.3: uevent
hub 2-6.3:1.0: 4 ports detected
hub 2-6.3:1.0: standalone hub
hub 2-6.3:1.0: individual port power switching
hub 2-6.3:1.0: individual port over-current protection
hub 2-6.3:1.0: power on to power good time: 100ms
hub 2-6.3:1.0: local power source is good
hub 2-6.3:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.8
drivers/usb/core/inode.c: creating file '008'
PM: Adding info for No Bus:ep_00
hub 2-3.1:1.0: state 7 ports 4 chg 0006 evt 0000
usb 2-6.3: uevent
hub 2-3.1:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
hub 2-3.1:1.0: port 1 not reset yet, waiting 10ms
usb 2-3.1.1: new low speed USB device using ehci_hcd and address 9
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: SAMSUNG SP2504C, VT100-41, max UDMA7
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
hub 2-3.1:1.0: port 1 not reset yet, waiting 10ms
hub 2-6.3:1.0: port 3: status 0301 change 0001
ata1.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access     ATA      SAMSUNG SP2504C  VT10 PQ: 0 ANSI: 5
PM: Adding info for scsi:target1:0:0
PM: Adding info for scsi:1:0:0:0
PM: Adding info for No Bus:1:0:0:0
PM: Adding info for No Bus:1:0:0:0
usb 2-3.1.1: skipped 1 descriptor after interface
usb 2-3.1.1: skipped 1 descriptor after interface
usb 2-3.1.1: default language 0x0409
usb 2-3.1.1: udev 9, busnum 2, minor = 136
usb 2-3.1.1: New USB device found, idVendor=10d5, idProduct=0004
usb 2-3.1.1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
usb 2-3.1.1: Product: PS2 to USB AdapterA3
PM: Adding info for usb:2-3.1.1
usb 2-3.1.1: uevent
usb 2-3.1.1: usb_probe_device
usb 2-3.1.1: configuration #1 chosen from 1 choice
usb 2-3.1.1: uevent
usb 2-3.1.1: adding 2-3.1.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.1:1.0
usb 2-3.1.1:1.0: uevent
usbhid 2-3.1.1:1.0: usb_probe_interface
usbhid 2-3.1.1:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:10D5:0004.0002
PM: Adding info for No Bus:input1
input: PS2 to USB AdapterA3 as /devices/pci0000:00/0000:00:0b.1/usb2/2-3/2-3.1/2-3.1.1/2-3.1.1:1.0/input/input1
usb 2-3.1.1: link qh8-0e01/c1dcde40 start 4 [1/2 us]
generic-usb 0003:10D5:0004.0002: input: USB HID v1.10 Keyboard [PS2 to USB AdapterA3] on usb-0000:00:0b.1-3.1.1/input0
PM: Adding info for No Bus:ep_81
usb 2-3.1.1: adding 2-3.1.1:1.1 (config #1, interface 1)
PM: Adding info for usb:2-3.1.1:1.1
usb 2-3.1.1:1.1: uevent
usbhid 2-3.1.1:1.1: usb_probe_interface
usbhid 2-3.1.1:1.1: usb_probe_interface - got id
PM: Adding info for hid:0003:10D5:0004.0003
PM: Adding info for No Bus:input2
input: PS2 to USB AdapterA3 as /devices/pci0000:00/0000:00:0b.1/usb2/2-3/2-3.1/2-3.1.1/2-3.1.1:1.1/input/input2
usb 2-3.1.1: link qh8-0e01/c1dcdf40 start 5 [1/2 us]
PM: Adding info for No Bus:mouse1
generic-usb 0003:10D5:0004.0003: input: USB HID v1.10 Mouse [PS2 to USB AdapterA3] on usb-0000:00:0b.1-3.1.1/input1
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev2.9
drivers/usb/core/inode.c: creating file '009'
PM: Adding info for No Bus:ep_00
usb 2-3.1.1: uevent
hub 2-3.1:1.0: port 2, status 0101, change 0000, 12 Mb/s
hub 2-3.1:1.0: port 2 not reset yet, waiting 10ms
usb 2-6.3: link qh128-0e01/c1dcdfc0 start 6 [1/2 us]
usb 2-3.1.2: new high speed USB device using ehci_hcd and address 10
hub 2-3.1:1.0: port 2 not reset yet, waiting 10ms
usb 2-3.1.2: default language 0x0409
usb 2-3.1.2: udev 10, busnum 2, minor = 137
usb 2-3.1.2: New USB device found, idVendor=05e3, idProduct=0605
usb 2-3.1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-3.1.2: Product: USB2.0 Hub
PM: Adding info for usb:2-3.1.2
usb 2-3.1.2: uevent
usb 2-3.1.2: usb_probe_device
usb 2-3.1.2: configuration #1 chosen from 1 choice
usb 2-3.1.2: adding 2-3.1.2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.2:1.0
usb 2-3.1.2:1.0: uevent
hub 2-3.1.2:1.0: usb_probe_interface
hub 2-3.1.2:1.0: usb_probe_interface - got id
hub 2-3.1.2:1.0: USB hub found
hub 2-3.1.2:1.0: 4 ports detected
hub 2-3.1.2:1.0: standalone hub
hub 2-3.1.2:1.0: individual port power switching
hub 2-3.1.2:1.0: individual port over-current protection
hub 2-3.1.2:1.0: Single TT
hub 2-3.1.2:1.0: TT requires at most 32 FS bit times (2664 ns)
hub 2-3.1.2:1.0: Port indicators are supported
hub 2-3.1.2:1.0: power on to power good time: 100ms
usb 2-3.1.2: uevent
hub 2-3.1.2:1.0: local power source is good
hub 2-3.1.2:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.10
drivers/usb/core/inode.c: creating file '010'
PM: Adding info for No Bus:ep_00
hub 2-6:1.0: state 7 ports 4 chg 0000 evt 0008
usb 2-3.1.2: uevent
hub 2-3.1:1.0: state 7 ports 4 chg 0000 evt 0002
hub 2-6.3:1.0: state 7 ports 4 chg 0008 evt 0000
hub 2-6.3:1.0: port 3, status 0301, change 0000, 1.5 Mb/s
usb 2-6.3.3: new low speed USB device using ehci_hcd and address 11
hub 2-3.1.2:1.0: port 1: status 0101 change 0001
hub 2-3.1.2:1.0: port 2: status 0301 change 0001
usb 2-6.3.3: skipped 1 descriptor after interface
usb 2-6.3.3: skipped 1 descriptor after interface
usb 2-6.3.3: default language 0x0409
usb 2-6.3.3: udev 11, busnum 2, minor = 138
usb 2-6.3.3: New USB device found, idVendor=2222, idProduct=0013
usb 2-6.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-6.3.3: Product: Macally iKeySlim
usb 2-6.3.3: Manufacturer: Macally Peripherals 
PM: Adding info for usb:2-6.3.3
usb 2-6.3.3: uevent
usb 2-6.3.3: usb_probe_device
usb 2-6.3.3: configuration #1 chosen from 1 choice
usb 2-6.3.3: uevent
usb 2-6.3.3: adding 2-6.3.3:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.3.3:1.0
usb 2-6.3.3:1.0: uevent
usbhid 2-6.3.3:1.0: usb_probe_interface
usbhid 2-6.3.3:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:0013.0004
PM: Adding info for No Bus:input3
input: Macally Peripherals  Macally iKeySlim as /devices/pci0000:00/0000:00:0b.1/usb2/2-6/2-6.3/2-6.3.3/2-6.3.3:1.0/input/input3
usb 2-6.3.3: link qh8-0e01/c1c92380 start 7 [1/2 us]
generic-usb 0003:2222:0013.0004: input: USB HID v1.10 Keyboard [Macally Peripherals  Macally iKeySlim] on usb-0000:00:0b.1-6.3.3/input0
PM: Adding info for No Bus:ep_81
usb 2-6.3.3: adding 2-6.3.3:1.1 (config #1, interface 1)
PM: Adding info for usb:2-6.3.3:1.1
usb 2-6.3.3:1.1: uevent
usbhid 2-6.3.3:1.1: usb_probe_interface
usbhid 2-6.3.3:1.1: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:0013.0005
PM: Adding info for No Bus:input4
input: Macally Peripherals  Macally iKeySlim as /devices/pci0000:00/0000:00:0b.1/usb2/2-6/2-6.3/2-6.3.3/2-6.3.3:1.1/input/input4
usb 2-6.3.3: link qh8-0e01/c1c924c0 start 0 [1/2 us]
PM: Adding info for No Bus:mouse2
generic-usb 0003:2222:0013.0005: input: USB HID v1.10 Mouse [Macally Peripherals  Macally iKeySlim] on usb-0000:00:0b.1-6.3.3/input1
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev2.11
drivers/usb/core/inode.c: creating file '011'
PM: Adding info for No Bus:ep_00
hub 2-6.3:1.0: state 7 ports 4 chg 0000 evt 0008
usb 2-6.3.3: uevent
usb 2-3.1.2: link qh256-0001/c1c92540 start 9 [1/0 us]
hub 2-3.1.2:1.0: state 7 ports 4 chg 0006 evt 0000
hub 2-3.1.2:1.0: port 1, status 0101, change 0000, 12 Mb/s
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ohci_hcd 0000:00:0b.0: auto-stop root hub
usb 2-3.1.2.1: new high speed USB device using ehci_hcd and address 12
ata2.00: ATA-7: ST3250620AS, 3.AAC, max UDMA/133
ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
hub 2-3.1.2:1.0: port 1 not reset yet, waiting 10ms
ata2.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access     ATA      ST3250620AS      3.AA PQ: 0 ANSI: 5
PM: Adding info for scsi:target2:0:0
PM: Adding info for scsi:2:0:0:0
PM: Adding info for No Bus:2:0:0:0
PM: Adding info for No Bus:2:0:0:0
usb 2-3.1.2.1: default language 0x0409
usb 2-3.1.2.1: udev 12, busnum 2, minor = 139
usb 2-3.1.2.1: New USB device found, idVendor=090c, idProduct=1000
usb 2-3.1.2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3.1.2.1: Product: DISK 2.0
usb 2-3.1.2.1: Manufacturer: USB
usb 2-3.1.2.1: SerialNumber: PHN84K6AD8PLXSVC
PM: Adding info for usb:2-3.1.2.1
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1: usb_probe_device
usb 2-3.1.2.1: configuration #1 chosen from 1 choice
usb 2-3.1.2.1: adding 2-3.1.2.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.2.1:1.0
usb 2-3.1.2.1:1.0: uevent
usb-storage 2-3.1.2.1:1.0: usb_probe_interface
usb-storage 2-3.1.2.1:1.0: usb_probe_interface - got id
scsi5 : SCSI emulation for USB Mass Storage devices
PM: Adding info for scsi:host5
PM: Adding info for No Bus:host5
usb-storage: device found at 12
usb-storage: waiting for device to settle before scanning
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:ep_02
PM: Adding info for No Bus:usbdev2.12
drivers/usb/core/inode.c: creating file '012'
PM: Adding info for No Bus:ep_00
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1: uevent
hub 2-3.1.2:1.0: port 2, status 0301, change 0000, 1.5 Mb/s
usb 2-3.1.2.2: new low speed USB device using ehci_hcd and address 13
hub 2-3.1.2:1.0: port 2 not reset yet, waiting 10ms
usb 2-3.1.2.2: skipped 1 descriptor after interface
usb 2-3.1.2.2: default language 0x0409
usb 2-3.1.2.2: udev 13, busnum 2, minor = 140
usb 2-3.1.2.2: New USB device found, idVendor=046d, idProduct=c050
usb 2-3.1.2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-3.1.2.2: Product: USB-PS/2 Optical Mouse
usb 2-3.1.2.2: Manufacturer: Logitech
PM: Adding info for usb:2-3.1.2.2
usb 2-3.1.2.2: uevent
usb 2-3.1.2.2: usb_probe_device
usb 2-3.1.2.2: configuration #1 chosen from 1 choice
usb 2-3.1.2.2: adding 2-3.1.2.2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.2.2:1.0
usb 2-3.1.2.2:1.0: uevent
usbhid 2-3.1.2.2:1.0: usb_probe_interface
usbhid 2-3.1.2.2:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:046D:C050.0006
usb 2-3.1.2.2: uevent
PM: Adding info for No Bus:input5
input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:0b.1/usb2/2-3/2-3.1/2-3.1.2/2-3.1.2.2/2-3.1.2.2:1.0/input/input5
PM: Adding info for No Bus:mouse3
generic-usb 0003:046D:C050.0006: input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:0b.1-3.1.2.2/input0
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.13
drivers/usb/core/inode.c: creating file '013'
PM: Adding info for No Bus:ep_00
hub 2-3.1.2:1.0: state 7 ports 4 chg 0000 evt 0002
usb 2-3.1.2.2: uevent
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATAPI: ATAPI   iHOS104, WL08, max UDMA/100
ata4.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access     Generic  USB SD Reader    1.00 PQ: 0 ANSI: 0
PM: Adding info for scsi:target0:0:0
PM: Adding info for scsi:0:0:0:0
PM: Adding info for No Bus:0:0:0:0
PM: Adding info for No Bus:0:0:0:0
scsi 0:0:0:1: Direct-Access     Generic  USB CF Reader    1.01 PQ: 0 ANSI: 0
PM: Adding info for scsi:0:0:0:1
PM: Adding info for No Bus:0:0:0:1
PM: Adding info for No Bus:0:0:0:1
scsi 0:0:0:2: Direct-Access     Generic  USB SM Reader    1.02 PQ: 0 ANSI: 0
PM: Adding info for scsi:0:0:0:2
PM: Adding info for No Bus:0:0:0:2
PM: Adding info for No Bus:0:0:0:2
scsi 0:0:0:3: Direct-Access     Generic  USB MS Reader    1.03 PQ: 0 ANSI: 0
PM: Adding info for scsi:0:0:0:3
PM: Adding info for No Bus:0:0:0:3
PM: Adding info for No Bus:0:0:0:3
usb-storage: device scan complete
PM: Adding info for No Bus:1:0:0:0
sd 1:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sda
 sda:
PM: Adding info for No Bus:2:0:0:0
PM: Adding info for No Bus:0:0:0:0
PM: Adding info for No Bus:0:0:0:1
PM: Adding info for No Bus:0:0:0:2
sd 2:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
PM: Adding info for No Bus:0:0:0:3
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sdb
 sdb:
PM: Adding info for No Bus:sdc
PM: Adding info for No Bus:8:32
PM: Adding info for No Bus:sdd
PM: Adding info for No Bus:8:48
sd 0:0:0:0: [sdc] Attached SCSI removable disk
 sda1 sda2 sda3 <
PM: Adding info for No Bus:sde
PM: Adding info for No Bus:8:64
PM: Adding info for No Bus:sdf
PM: Adding info for No Bus:8:80
sd 0:0:0:1: [sdd] Attached SCSI removable disk
sd 0:0:0:2: [sde] Attached SCSI removable disk
sd 0:0:0:3: [sdf] Attached SCSI removable disk
 unknown partition table
PM: Adding info for No Bus:8:16
sd 2:0:0:0: [sdb] Attached SCSI disk
 >
PM: Adding info for No Bus:sda1
PM: Adding info for No Bus:sda2
PM: Adding info for No Bus:sda3
PM: Adding info for No Bus:8:0
sd 1:0:0:0: [sda] Attached SCSI disk
scsi 5:0:0:0: Direct-Access     USB      DISK 2.0         0403 PQ: 0 ANSI: 0 CCS
PM: Adding info for scsi:target5:0:0
PM: Adding info for scsi:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
usb-storage: device scan complete
sd 5:0:0:0: [sdg] 3981312 512-byte logical blocks: (2.03 GB/1.89 GiB)
sd 5:0:0:0: [sdg] Write Protect is off
sd 5:0:0:0: [sdg] Mode Sense: 43 00 00 00
sd 5:0:0:0: [sdg] Assuming drive cache: write through
PM: Adding info for No Bus:sdg
sd 5:0:0:0: [sdg] Assuming drive cache: write through
 sdg: sdg1
PM: Adding info for No Bus:sdg1
PM: Adding info for No Bus:8:96
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sd 5:0:0:0: [sdg] Attached SCSI removable disk
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 60 00
ata4.00: cmd a0/01:00:00:60:00/00:00:00:00:00/a0 tag 0 dma 96 in
         res 40/00:02:00:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4: EH complete
ata4: limiting SATA link speed to 1.5 Gbps
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 60 00
ata4.00: cmd a0/01:00:00:60:00/00:00:00:00:00/a0 tag 0 dma 96 in
         res 40/00:02:00:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4: EH complete
ata4.00: limiting speed to UDMA/66:PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 60 00
ata4.00: cmd a0/01:00:00:60:00/00:00:00:00:00/a0 tag 0 dma 96 in
         res 40/00:02:00:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/66
ata4: EH complete
ata4.00: limiting speed to UDMA/33:PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 60 00
ata4.00: cmd a0/01:00:00:60:00/00:00:00:00:00/a0 tag 0 dma 96 in
         res 40/00:02:00:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/33
scsi scan: 96 byte inquiry failed.  Consider BLIST_INQUIRY_36 for this device
ata4: EH complete
scsi 4:0:0:0: CD-ROM            ATAPI    iHOS104          WL08 PQ: 0 ANSI: 5
PM: Adding info for scsi:target4:0:0
PM: Adding info for scsi:4:0:0:0
PM: Adding info for No Bus:4:0:0:0
PM: Adding info for No Bus:4:0:0:0
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.1: uevent
usb 2-2:1.0: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
ide-cd driver 5.00
PM: Adding info for No Bus:0.0
ide-cd: hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
Uniform CD-ROM driver Revision: 3.20
PM: Adding info for No Bus:hda
PM: Adding info for No Bus:3:0
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
PM: Adding info for No Bus:device-mapper
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
PM: Adding info for No Bus:dm-0
PM: Adding info for No Bus:254:0
PM: Adding info for No Bus:dm-1
PM: Adding info for No Bus:dm-2
PM: Adding info for No Bus:254:2
PM: Adding info for No Bus:254:1
PM: Adding info for No Bus:dm-3
PM: Adding info for No Bus:254:3
PM: Adding info for No Bus:dm-4
PM: Adding info for No Bus:254:4
PM: Adding info for No Bus:dm-5
PM: Adding info for No Bus:254:5
PM: Removing info for No Bus:254:1
PM: Removing info for No Bus:dm-1
PM: Adding info for No Bus:dm-1
PM: Adding info for No Bus:254:1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
xor: automatically using best checksumming function: pIII_sse
   pIII_sse  :  7516.000 MB/sec
xor: using function: pIII_sse (7516.000 MB/sec)
raid6: int32x1    878 MB/s
raid6: int32x2    839 MB/s
raid6: int32x4    703 MB/s
raid6: int32x8    585 MB/s
raid6: mmxx1     2742 MB/s
raid6: mmxx2     3167 MB/s
raid6: sse1x1    1890 MB/s
raid6: sse1x2    2441 MB/s
raid6: sse2x1    3546 MB/s
raid6: sse2x2    4222 MB/s
raid6: using algorithm sse2x2 (4222 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
PM: Marking nosave pages: 000000000009c000 - 0000000000100000
PM: Basic memory bitmaps created
PM: Basic memory bitmaps freed
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
udev: starting version 146
usb usb1: uevent
usb 1-0:1.0: uevent
usb usb2: uevent
usb 2-0:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-3: uevent
usb 2-3.1: uevent
usb 2-3.1.1: uevent
usb 2-3.1.1:1.0: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.2: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.2: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2:1.0: uevent
usb 2-3.1:1.0: uevent
usb 2-3:1.0: uevent
usb 2-6: uevent
usb 2-6.1: uevent
usb 2-6.1:1.0: uevent
usb 2-6.3: uevent
usb 2-6.3.3: uevent
usb 2-6.3.3:1.0: uevent
usb 2-6.3.3:1.1: uevent
usb 2-6.3:1.0: uevent
usb 2-6:1.0: uevent
usb usb1: uevent
usb usb2: uevent
usb usb2: uevent
usb usb1: uevent
PM: Adding info for No Bus:input6
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input6
ACPI: Power Button [PWRB]
PM: Adding info for No Bus:input7
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input7
ACPI: Power Button [PWRF]
usb 2-6: uevent
usb 2-3: uevent
usb 2-2: uevent
usb 2-3: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
ACPI: SSDT 7fefa940 00175 (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
PM: Adding info for No Bus:cooling_device1
processor LNXCPU:00: registered as cooling_device1
ACPI: SSDT 7fefad50 000CE (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
PM: Adding info for No Bus:cooling_device2
processor LNXCPU:01: registered as cooling_device2
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-6: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-6.3: uevent
usb 2-6.1: uevent
usb 2-3.1: uevent
usb 2-6.3: uevent
usb 2-2:1.0: uevent
usb 2-6.1: uevent
usb 2-3.1: uevent
usb 2-3.1.2: uevent
usb 2-3.1.1: uevent
usb 2-3.1.2: uevent
usb 2-6.3.3: uevent
usb 2-3.1.1: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.2: uevent
usb 2-6.3.3: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.2: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
PM: Adding info for No Bus:rtc
Real Time Clock Driver v1.12b
PM: Adding info for No Bus:hwmon0
PM: Adding info for No Bus:event0
PM: Adding info for No Bus:event1
PM: Adding info for No Bus:event2
PM: Adding info for No Bus:event3
PM: Adding info for No Bus:event4
PM: Adding info for No Bus:event5
PM: Adding info for No Bus:event6
PM: Adding info for No Bus:event7
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2.2: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2.2: uevent
usb 2-6.3.3:1.0: uevent
usb 2-6.3.3: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-6.3.3:1.0: uevent
PM: Adding info for No Bus:raw1394
ieee1394: raw1394: /dev/raw1394 device initialized
ACPI: I/O resource nForce2_smbus [0x5000-0x503f] conflicts with ACPI region SM00 [0x5000-0x5005]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
nForce2_smbus 0000:00:0a.1: Error probing SMB1.
PM: Adding info for i2c:i2c-0
i2c i2c-0: nForce2 SMBus adapter at 0x5100
usb 2-6.1:1.0: uevent
usb 2-6.1: uevent
usb 2-6.1:1.0: uevent
usb 2-6.1: uevent
usb 2-6.1:1.0: uevent
usb 2-6.1:1.0: uevent
usb 2-6.3.3:1.1: uevent
usb 2-6.3.3: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.1: uevent
usb 2-6.3.3:1.1: uevent
usb 2-3.1.1:1.0: uevent
usb 2-3.1.1: uevent
usb 2-6.3.3:1.1: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.1: uevent
usb 2-6.3.3: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.1:1.0: uevent
usb 2-6.3.3:1.1: uevent
PM: Adding info for No Bus:dv1394-0
PM: Adding info for No Bus:timer
PM: Adding info for No Bus:seq
hda: UDMA/66 mode selected
hda: task_no_data_intr: status=0x41 { DriveReady Error }
hda: task_no_data_intr: error=0x04 { AbortedCommand }
hda: possibly failed opcode: 0xe3
PM: Adding info for No Bus:sequencer
PM: Adding info for No Bus:sequencer2
ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
HDA Intel 0000:00:10.1: PCI INT B -> Link[AAZA] -> GSI 23 (level, low) -> IRQ 23
HDA Intel 0000:00:10.1: setting latency timer to 64
PM: Adding info for No Bus:input8
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:10.1/input/input8
PM: Adding info for No Bus:event8
PM: Adding info for No Bus:card0
PM: Adding info for No Bus:pcmC0D1p
PM: Adding info for No Bus:adsp
PM: Adding info for No Bus:pcmC0D0p
PM: Adding info for No Bus:pcmC0D0c
PM: Adding info for No Bus:dsp
PM: Adding info for No Bus:audio
PM: Adding info for No Bus:hwC0D0
PM: Adding info for No Bus:controlC0
PM: Adding info for No Bus:mixer
ata4.00: limiting speed to PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 4:0:0:0: CDB: Mode Sense(10): 5a 00 2a 00 00 00 00 00 80 00
ata4.00: cmd a0/01:00:00:80:00/00:00:00:00:00/a0 tag 0 dma 16512 in
         res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO4
ata4: EH complete
sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
PM: Adding info for No Bus:sr0
PM: Adding info for No Bus:11:0
sr 4:0:0:0: Attached scsi CD-ROM sr0
PM: Adding info for No Bus:sg0
sd 1:0:0:0: Attached scsi generic sg0 type 0
PM: Adding info for No Bus:sg1
sd 2:0:0:0: Attached scsi generic sg1 type 0
PM: Adding info for No Bus:sg2
sd 0:0:0:0: Attached scsi generic sg2 type 0
PM: Adding info for No Bus:sg3
sd 0:0:0:1: Attached scsi generic sg3 type 0
PM: Adding info for No Bus:sg4
sd 0:0:0:2: Attached scsi generic sg4 type 0
PM: Adding info for No Bus:sg5
sd 0:0:0:3: Attached scsi generic sg5 type 0
PM: Adding info for No Bus:sg6
sd 5:0:0:0: Attached scsi generic sg6 type 0
PM: Adding info for No Bus:sg7
sr 4:0:0:0: Attached scsi generic sg7 type 5
PM: Adding info for No Bus:vcs2
PM: Adding info for No Bus:vcsa2
PM: Adding info for No Bus:vcs3
PM: Adding info for No Bus:vcsa3
PM: Adding info for No Bus:vcs4
PM: Adding info for No Bus:vcsa4
PM: Adding info for No Bus:vcs5
PM: Adding info for No Bus:vcsa5
PM: Adding info for No Bus:vcs6
PM: Adding info for No Bus:vcsa6
hda: UDMA/66 mode selected
hda: task_no_data_intr: status=0x41 { DriveReady Error }
hda: task_no_data_intr: error=0x04 { AbortedCommand }
hda: possibly failed opcode: 0xe3
EXT3 FS on dm-2, internal journal
i2c /dev entries driver
PM: Adding info for No Bus:i2c-0
it87: Found IT8712F chip at 0x290, revision 7
it87: in3 is VCC (+5V)
it87: in7 is VCCH (+5V Stand-By)
ACPI: I/O resource it87 [0x295-0x296] conflicts with ACPI region HWRE [0x295-0x296]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
fuse init (API version 7.13)
PM: Adding info for No Bus:fuse
kjournald starting.  Commit interval 5 seconds
EXT3 FS on dm-5, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
PM: Adding info for No Bus:254:3-fuseblk
PM: Adding info for No Bus:254:1-fuseblk
Adding 4194296k swap on /mnt/oldlin/4G-memory.swap.  Priority:-1 extents:1057 across:4264956k 
r8169: eth1: link up
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PM: Adding info for No Bus:0:16
PM: Adding info for No Bus:0:17
PM: Adding info for No Bus:0:18
PM: Adding info for No Bus:vcs10
PM: Adding info for No Bus:vcsa10
usb 2-6.1: link qh8-0e01/c216bac0 start 2 [1/2 us]
usb 2-3.1.2.2: link qh8-0e01/c216bd00 start 3 [1/2 us]
usb 2-6.1: unlink qh8-0e01/c216bac0 start 2 [1/2 us]
usb 2-3.1.2.2: unlink qh8-0e01/c216bd00 start 3 [1/2 us]
ehci_hcd 0000:00:0b.1: reused qh c216bac0 schedule
usb 2-6.1: link qh8-0e01/c216bac0 start 2 [1/2 us]
ehci_hcd 0000:00:0b.1: reused qh c216bd00 schedule
usb 2-3.1.2.2: link qh8-0e01/c216bd00 start 3 [1/2 us]
irda_init()
NET: Registered protocol family 23
usbcore: registered new interface driver stir4200
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
warning: `ntpd' uses 32-bit capabilities (legacy support in use)
usb usb1: uevent
usb 1-0:1.0: uevent
usb usb2: uevent
usb 2-0:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-3: uevent
usb 2-3.1: uevent
usb 2-3.1.1: uevent
usb 2-3.1.1:1.0: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.2: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.2: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2:1.0: uevent
usb 2-3.1:1.0: uevent
usb 2-3:1.0: uevent
usb 2-6: uevent
usb 2-6.1: uevent
usb 2-6.1:1.0: uevent
usb 2-6.3: uevent
usb 2-6.3.3: uevent
usb 2-6.3.3:1.0: uevent
usb 2-6.3.3:1.1: uevent
usb 2-6.3:1.0: uevent
usb 2-6:1.0: uevent
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.14
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
CPUFREQ: Per core ondemand sysfs interface is deprecated - up_threshold
CPUFREQ: Per core ondemand sysfs interface is deprecated - ignore_nice_load
PM: Adding info for No Bus:vcs7
PM: Adding info for No Bus:vcsa7
Linux agpgart interface v0.103
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
nvidia 0000:01:00.0: PCI INT A -> Link[APC5] -> GSI 16 (level, low) -> IRQ 16
nvidia 0000:01:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86 Kernel Module  185.18.36  Fri Aug 14 17:18:04 PDT 2009
PM: Adding info for i2c:i2c-1
PM: Adding info for No Bus:i2c-1
PM: Adding info for i2c:i2c-2
PM: Adding info for No Bus:i2c-2
PM: Adding info for i2c:i2c-3
PM: Adding info for No Bus:i2c-3