[PATCH v3 0/3] arm64: dts: qcom: x1e80100-hp-x14: dt for HP Omnibook X Laptop 14

[PATCH v3 0/3] arm64: dts: qcom: x1e80100-hp-x14: dt for HP Omnibook X Laptop 14

[Jens Glathe via B4 Relay]

Introduce device tree for the HP Omnibook X Laptop 14-fe0750ng
(hp-omnibook-x14). It is a Laptop based on the Qualcomm Snapdragon
X Elite SoC. There seem to be other SKUs, some with Wifi-7 (WCN7850)
instead of Wifi-6E (WCN6855). This dt explicitly supports WCN6855,
I haven't found a good way yet to describe both.
    
PDF link: https://www8.hp.com/h20195/V2/GetPDF.aspx/c08989140

Supported features:
    
- Keyboard (no function keys though)
- Display (IPS 2240x1400, 300nits)
- PWM brightness control (works via brightnessctl)
- Touchpad
- Touchscreen
- PCIe ports (pcie4, pcie6a)
- USB type-c, type-a
- WCN6855 Wifi-6E
- WCN6855 Bluetooth
- ADSP and CDSP
- X1 GPU
- GPIO Keys (Lid switch)
- Audio definition (works via USB)
- prepared for DP Altmode

Bringup work has started with the Asus Vivobook S15 as initial template,
worked from there by comparing and copying from the CRD, QCP, 
Yoga Slim 7, Thinkpad T14s. Special thanks to all the people that helped
on #aarch64-laptops [1] with comments and suggestions.
I tested on my laptop, mostly. Since the dt is also in Ubuntu-Concept X1E
[2] there is also test exposure there, with some feedback.

For WiFi to work you need a board file matching the board string [3]. By 
experiment and pure guess I found the already existing calibration for
HP_G8_LANCIA_14 to be quite nice, it gives 866MB/s link speed here. A 
patch proposal [5] has been sent.

For this patchset to work you also need patch [4] in the tree,
otherwise uart14 for BT will be mising.

[1] https://oftc.irclog.whitequark.org/aarch64-laptops
[2] https://discourse.ubuntu.com/t/ubuntu-24-10-concept-snapdragon-x-elite/48800
[3] "bus=pci,vendor=17cb,device=1103,subsystem-vendor=105b,subsystem-device=e108,qmi-chip-id=2,qmi-board-id=255"
[4] https://lore.kernel.org/all/20241007-x1e80100-pwrseq-qcp-v1-0-f7166510ab17@linaro.org/
[5] https://lore.kernel.org/all/f6693075-60ea-4fed-8453-9e124e94203b@oldschoolsolutions.biz/

To: Bjorn Andersson <andersson@kernel.org>
To: Konrad Dybcio <konradybcio@kernel.org>
To: Rob Herring <robh@kernel.org>
To: Krzysztof Kozlowski <krzk+dt@kernel.org>
To: Conor Dooley <conor+dt@kernel.org>
To: Kalle Valo <kvalo@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>

Changes in v3:
- removed patch for the BOE panel from the set, already merged
  c1bae6802ee9 drm/panel-edp: Add unknown BOE panel for HP Omnibook X14
- added link to the WiFi board file patch
- Link to v2: https://lore.kernel.org/r/20241130-hp-omnibook-x14-v2-0-72227bc6bbf4@oldschoolsolutions.biz

Changes in v2:
- amended usb_mp_dwc3 definition to reference both phys that are used,
  as suggested by Krishna Kurapati
- Link to v1: https://lore.kernel.org/r/20241124-hp-omnibook-x14-v1-0-e4262f0254fa@oldschoolsolutions.biz

---
Jens Glathe (3):
      dt-bindings: arm: qcom: Add HP Omnibook X 14
      firmware: qcom: scm: Allow QSEECOM for HP Omnibook X14
      arm64: dts: qcom: x1e80100-hp-x14: dt for HP Omnibook X Laptop 14

 Documentation/devicetree/bindings/arm/qcom.yaml    |    1 +
 arch/arm64/boot/dts/qcom/Makefile                  |    1 +
 .../boot/dts/qcom/x1e80100-hp-omnibook-x14.dts     | 1693 ++++++++++++++++++++
 drivers/firmware/qcom/qcom_scm.c                   |    1 +
 4 files changed, 1696 insertions(+)
---
base-commit: 02d920be494a5f953319e7589d23a8ba3f00ce05
change-id: 20241116-hp-omnibook-x14-90539fac715d

Best regards,
-- 
Jens Glathe <jens.glathe@oldschoolsolutions.biz>

[PATCH v3 1/3] dt-bindings: arm: qcom: Add HP Omnibook X 14

[Jens Glathe via B4 Relay]

From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>

Add compatible values for the HP Omnibook X Laptop 14-fe0750ng,
using "hp,omnibook-x14"

The laptop is based on the Snapdragon X Elite (x1e80100) SoC.

PDF link: https://www8.hp.com/h20195/V2/GetPDF.aspx/c08989140

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index ca39903935104..62e197a1e7603 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -1103,6 +1103,7 @@ properties:
           - enum:
               - asus,vivobook-s15
               - dell,xps13-9345
+              - hp,omnibook-x14
               - lenovo,yoga-slim7x
               - microsoft,romulus13
               - microsoft,romulus15

-- 
2.43.0

[PATCH v3 2/3] firmware: qcom: scm: Allow QSEECOM for HP Omnibook X14

[Jens Glathe via B4 Relay]

From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>

add "hp,omnibook-x14" as compatible device for QSEECOM

This is required to get access to efivars and uefi boot loader support.

Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
 drivers/firmware/qcom/qcom_scm.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/firmware/qcom/qcom_scm.c b/drivers/firmware/qcom/qcom_scm.c
index 72bf87ddcd969..2e148fb7167be 100644
--- a/drivers/firmware/qcom/qcom_scm.c
+++ b/drivers/firmware/qcom/qcom_scm.c
@@ -1769,6 +1769,7 @@ EXPORT_SYMBOL_GPL(qcom_scm_qseecom_app_send);
  */
 static const struct of_device_id qcom_scm_qseecom_allowlist[] __maybe_unused = {
 	{ .compatible = "dell,xps13-9345" },
+	{ .compatible = "hp,omnibook-x14" },
 	{ .compatible = "lenovo,flex-5g" },
 	{ .compatible = "lenovo,thinkpad-t14s" },
 	{ .compatible = "lenovo,thinkpad-x13s", },

-- 
2.43.0

[PATCH v3 3/3] arm64: dts: qcom: x1e80100-hp-x14: dt for HP Omnibook X Laptop 14

[Jens Glathe via B4 Relay]

From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>

Introduce device tree for the HP Omnibook X Laptop 14-fe0750ng
(hp-omnibook-x14). It is a Laptop based on the Qualcomm Snapdragon
X Elite SoC. There seem to be other SKUs, some with Wifi-7 (WCN7850)
instead of Wifi-6E (WCN6855). This dt explicitly supports WCN6855,
I haven't found a good way yet to describe both.

PDF link: https://www8.hp.com/h20195/V2/GetPDF.aspx/c08989140

Supported features:

- Keyboard (no function keys though)
- Display
- PWM brightness control (works via brightnessctl)
- Touchpad
- Touchscreen
- PCIe ports (pcie4, pcie6a)
- USB type-c, type-a
- WCN6855 Wifi-6E
- WCN6855 Bluetooth
- ADSP and CDSP
- X1 GPU
- GPIO Keys (Lid switch)
- Audio definition (works via USB)

Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
 arch/arm64/boot/dts/qcom/Makefile                  |    1 +
 .../boot/dts/qcom/x1e80100-hp-omnibook-x14.dts     | 1693 ++++++++++++++++++++
 2 files changed, 1694 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 9bb8b191aeb51..0916b4232574e 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -286,6 +286,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= x1e78100-lenovo-thinkpad-t14s.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-asus-vivobook-s15.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-crd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-dell-xps13-9345.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-hp-omnibook-x14.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-lenovo-yoga-slim7x.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-microsoft-romulus13.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-microsoft-romulus15.dtb
diff --git a/arch/arm64/boot/dts/qcom/x1e80100-hp-omnibook-x14.dts b/arch/arm64/boot/dts/qcom/x1e80100-hp-omnibook-x14.dts
new file mode 100644
index 0000000000000..cd860a246c450
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/x1e80100-hp-omnibook-x14.dts
@@ -0,0 +1,1693 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2024, Xilin Wu <wuxilin123@gmail.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "x1e80100.dtsi"
+#include "x1e80100-pmics.dtsi"
+
+/ {
+	model = "HP Omnibook X 14";
+	compatible = "hp,omnibook-x14", "qcom,x1e80100";
+	chassis-type = "laptop";
+
+	aliases {
+		serial0 = &uart21;
+		serial1 = &uart14;
+	};
+
+	wcd938x: audio-codec {
+		compatible = "qcom,wcd9385-codec";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wcd_default>;
+
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+		qcom,micbias4-microvolt = <1800000>;
+		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+		qcom,rx-device = <&wcd_rx>;
+		qcom,tx-device = <&wcd_tx>;
+
+		reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;
+
+		vdd-buck-supply = <&vreg_l15b_1p8>;
+		vdd-rxtx-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l15b_1p8>;
+		vdd-mic-bias-supply = <&vreg_bob1>;
+
+		#sound-dai-cells = <1>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pmk8550_pwm 0 5000000>;
+
+		brightness-levels = <0 2048 4096 8192 16384 65535>;
+		num-interpolated-steps = <20>;
+		default-brightness-level = <80>;
+
+		enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>;
+		power-supply = <&vreg_edp_bl>;
+
+		pinctrl-0 = <&edp_bl_en>, <&edp_bl_pwm>;
+		pinctrl-names = "default";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&hall_int_n_default>;
+		pinctrl-names = "default";
+
+		switch-lid {
+			gpios = <&tlmm 92 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			wakeup-source;
+			wakeup-event-action = <EV_ACT_DEASSERTED>;
+		};
+	};
+
+	pmic-glink {
+		compatible = "qcom,x1e80100-pmic-glink",
+			     "qcom,sm8550-pmic-glink",
+			     "qcom,pmic-glink";
+		orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
+				    <&tlmm 123 GPIO_ACTIVE_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Left-side port, closer to the screen */
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss0_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss0_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss0_ss_in: endpoint {
+						remote-endpoint = <&retimer_ss0_ss_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss0_con_sbu_in: endpoint {
+						remote-endpoint = <&retimer_ss0_con_sbu_out>;
+					};
+				};
+			};
+		};
+
+		/* Left-side port, farther from the screen */
+		connector@1 {
+			compatible = "usb-c-connector";
+			reg = <1>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss1_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss1_ss_in: endpoint {
+						remote-endpoint = <&retimer_ss1_ss_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss1_con_sbu_in: endpoint {
+						remote-endpoint = <&retimer_ss1_con_sbu_out>;
+					};
+				};
+			};
+		};
+	};
+
+	reserved-memory {
+		linux,cma {
+			compatible = "shared-dma-pool";
+			size = <0x0 0x8000000>;
+			reusable;
+			linux,cma-default;
+		};
+	};
+
+	sound {
+		compatible = "qcom,x1e80100-sndcard";
+		model = "X1E80100-HP-OMNIBOOK-X14";
+		audio-routing = "SpkrLeft IN", "WSA WSA_SPK1 OUT",
+				"SpkrRight IN", "WSA WSA_SPK2 OUT",
+				"IN1_HPHL", "HPHL_OUT",
+				"IN2_HPHR", "HPHR_OUT",
+				"AMIC2", "MIC BIAS2",
+				"VA DMIC0", "MIC BIAS3",
+				"VA DMIC1", "MIC BIAS3",
+				"VA DMIC2", "MIC BIAS1",
+				"VA DMIC3", "MIC BIAS1",
+				"VA DMIC0", "VA MIC BIAS3",
+				"VA DMIC1", "VA MIC BIAS3",
+				"VA DMIC2", "VA MIC BIAS1",
+				"VA DMIC3", "VA MIC BIAS1",
+				"TX SWR_INPUT1", "ADC2_OUTPUT";
+
+		wcd-playback-dai-link {
+			link-name = "WCD Playback";
+
+			cpu {
+				sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+			};
+
+			codec {
+				sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wcd-capture-dai-link {
+			link-name = "WCD Capture";
+
+			cpu {
+				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+			};
+
+			codec {
+				sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wsa-dai-link {
+			link-name = "WSA Playback";
+
+			cpu {
+				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+			};
+
+			codec {
+				sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&lpass_wsamacro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		va-dai-link {
+			link-name = "VA Capture";
+
+			cpu {
+				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+			};
+
+			codec {
+				sound-dai = <&lpass_vamacro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+	};
+
+	vreg_edp_3p3: regulator-edp-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_EDP_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&edp_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_edp_bl: regulator-edp-bl {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VBL9";
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		gpio = <&pmc8380_3_gpios 10 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&edp_bl_reg_en>;
+
+		regulator-boot-on;
+	};
+
+	vreg_misc_3p3: regulator-misc-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_MISC_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pm8550ve_8_gpios 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&misc_3p3_reg_en>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vreg_nvme: regulator-nvme {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_NVME_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&nvme_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr0_1p15: regulator-rtmr0-1p15 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_1P15";
+		regulator-min-microvolt = <1150000>;
+		regulator-max-microvolt = <1150000>;
+
+		gpio = <&pmc8380_5_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb0_pwr_1p15_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr0_1p8: regulator-rtmr0-1p8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_1P8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&pm8550ve_9_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb0_1p8_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr0_3p3: regulator-rtmr0-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb0_3p3_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr1_1p15: regulator-rtmr1-1p15 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR1_1P15";
+		regulator-min-microvolt = <1150000>;
+		regulator-max-microvolt = <1150000>;
+
+		gpio = <&tlmm 188 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb1_pwr_1p15_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr1_1p8: regulator-rtmr1-1p8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR1_1P8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 175 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb1_pwr_1p8_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr1_3p3: regulator-rtmr1-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR1_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 186 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb1_pwr_3p3_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_vph_pwr: regulator-vph-pwr {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vreg_vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vreg_wcn_3p3: regulator-wcn-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&wcn_sw_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	/*
+	 * TODO: These two regulators are actually part of the removable M.2
+	 * card and not the CRD mainboard. Need to describe this differently.
+	 * Functionally it works correctly, because all we need to do is to
+	 * turn on the actual 3.3V supply above.
+	 */
+	vreg_wcn_0p95: regulator-wcn-0p95 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_0P95";
+		regulator-min-microvolt = <950000>;
+		regulator-max-microvolt = <950000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	vreg_wcn_1p9: regulator-wcn-1p9 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_1P9";
+		regulator-min-microvolt = <1900000>;
+		regulator-max-microvolt = <1900000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	wcn6855-pmu {
+		compatible = "qcom,wcn6855-pmu";
+
+		vddaon-supply = <&vreg_wcn_0p95>;
+		vddio-supply = <&vreg_wcn_1p9>;
+		vddpcie1p3-supply = <&vreg_wcn_1p9>;
+		vddpcie1p9-supply = <&vreg_wcn_1p9>;
+		vddpmu-supply = <&vreg_wcn_0p95>;
+		vddpmumx-supply = <&vreg_wcn_0p95>;
+		vddpmucx-supply = <&vreg_wcn_0p95>;
+		vddrfa0p95-supply = <&vreg_wcn_0p95>;
+		vddrfa1p3-supply = <&vreg_wcn_1p9>;
+		vddrfa1p9-supply = <&vreg_wcn_1p9>;
+
+		wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
+		bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&wcn_wlan_bt_en>;
+		pinctrl-names = "default";
+
+		regulators {
+			vreg_pmu_rfa_cmn_0p8: ldo0 {
+				regulator-name = "vreg_pmu_rfa_cmn_0p8";
+			};
+
+			vreg_pmu_aon_0p8: ldo1 {
+				regulator-name = "vreg_pmu_aon_0p8";
+			};
+
+			vreg_pmu_wlcx_0p8: ldo2 {
+				regulator-name = "vreg_pmu_wlcx_0p8";
+			};
+
+			vreg_pmu_wlmx_0p8: ldo3 {
+				regulator-name = "vreg_pmu_wlmx_0p8";
+			};
+
+			vreg_pmu_btcmx_0p8: ldo4 {
+				regulator-name = "vreg_pmu_btcmx_0p8";
+			};
+
+			vreg_pmu_pcie_1p8: ldo5 {
+				regulator-name = "vreg_pmu_pcie_1p8";
+			};
+
+			vreg_pmu_pcie_0p9: ldo6 {
+				regulator-name = "vreg_pmu_pcie_0p9";
+			};
+
+			vreg_pmu_rfa_0p8: ldo7 {
+				regulator-name = "vreg_pmu_rfa_0p8";
+			};
+
+			vreg_pmu_rfa_1p2: ldo8 {
+				regulator-name = "vreg_pmu_rfa_1p2";
+			};
+
+			vreg_pmu_rfa_1p7: ldo9 {
+				regulator-name = "vreg_pmu_rfa_1p7";
+			};
+		};
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8550-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-bob1-supply = <&vreg_vph_pwr>;
+		vdd-bob2-supply = <&vreg_vph_pwr>;
+		vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>;
+		vdd-l2-l13-l14-supply = <&vreg_bob1>;
+		vdd-l5-l16-supply = <&vreg_bob1>;
+		vdd-l6-l7-supply = <&vreg_bob2>;
+		vdd-l8-l9-supply = <&vreg_bob1>;
+		vdd-l12-supply = <&vreg_s5j_1p2>;
+		vdd-l15-supply = <&vreg_s4c_1p8>;
+		vdd-l17-supply = <&vreg_bob2>;
+
+		vreg_bob1: bob1 {
+			regulator-name = "vreg_bob1";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob2: bob2 {
+			regulator-name = "vreg_bob2";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1b_1p8: ldo1 {
+			regulator-name = "vreg_l1b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p0: ldo2 {
+			regulator-name = "vreg_l2b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4b_1p8: ldo4 {
+			regulator-name = "vreg_l4b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_3p0: ldo5 {
+			regulator-name = "vreg_l5b_3p0";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b_1p8: ldo6 {
+			regulator-name = "vreg_l6b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b_2p8: ldo7 {
+			regulator-name = "vreg_l7b_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8b_3p0: ldo8 {
+			regulator-name = "vreg_l8b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b_2p9: ldo9 {
+			regulator-name = "vreg_l9b_2p9";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10b_1p8: ldo10 {
+			regulator-name = "vreg_l10b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12b_1p2: ldo12 {
+			regulator-name = "vreg_l12b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13b_3p0: ldo13 {
+			regulator-name = "vreg_l13b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14b_3p0: ldo14 {
+			regulator-name = "vreg_l14b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15b_1p8: ldo15 {
+			regulator-name = "vreg_l15b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16b_2p9: ldo16 {
+			regulator-name = "vreg_l16b_2p9";
+			regulator-min-microvolt = <2912000>;
+			regulator-max-microvolt = <2912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17b_2p5: ldo17 {
+			regulator-name = "vreg_l17b_2p5";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-l1-supply = <&vreg_s5j_1p2>;
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s4-supply = <&vreg_vph_pwr>;
+
+		vreg_s4c_1p8: smps4 {
+			regulator-name = "vreg_s4c_1p8";
+			regulator-min-microvolt = <1856000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1c_1p2: ldo1 {
+			regulator-name = "vreg_l1c_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c_0p8: ldo2 {
+			regulator-name = "vreg_l2c_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c_0p8: ldo3 {
+			regulator-name = "vreg_l3c_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vdd-l1-supply = <&vreg_s1f_0p7>;
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s4c_1p8>;
+		vdd-s1-supply = <&vreg_vph_pwr>;
+
+		vreg_l1d_0p8: ldo1 {
+			regulator-name = "vreg_l1d_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2d_0p9: ldo2 {
+			regulator-name = "vreg_l2d_0p9";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3d_1p8: ldo3 {
+			regulator-name = "vreg_l3d_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-3 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
+
+		vreg_l2e_0p8: ldo2 {
+			regulator-name = "vreg_l2e_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-4 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "f";
+
+		vdd-l1-supply = <&vreg_s5j_1p2>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
+		vdd-s1-supply = <&vreg_vph_pwr>;
+
+		vreg_s1f_0p7: smps1 {
+			regulator-name = "vreg_s1f_0p7";
+			regulator-min-microvolt = <700000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1f_1p0: ldo1 {
+			regulator-name = "vreg_l1f_1p0";
+			regulator-min-microvolt = <1024000>;
+			regulator-max-microvolt = <1024000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2f_1p0: ldo2 {
+			regulator-name = "vreg_l2f_1p0";
+			regulator-min-microvolt = <1024000>;
+			regulator-max-microvolt = <1024000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3f_1p0: ldo3 {
+			regulator-name = "vreg_l3f_1p0";
+			regulator-min-microvolt = <1024000>;
+			regulator-max-microvolt = <1024000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-6 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "i";
+
+		vdd-l1-supply = <&vreg_s4c_1p8>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s1-supply = <&vreg_vph_pwr>;
+		vdd-s2-supply = <&vreg_vph_pwr>;
+
+		vreg_s1i_0p9: smps1 {
+			regulator-name = "vreg_s1i_0p9";
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s2i_1p0: smps2 {
+			regulator-name = "vreg_s2i_1p0";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1i_1p8: ldo1 {
+			regulator-name = "vreg_l1i_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2i_1p2: ldo2 {
+			regulator-name = "vreg_l2i_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3i_0p8: ldo3 {
+			regulator-name = "vreg_l3i_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-7 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "j";
+
+		vdd-l1-supply = <&vreg_s1f_0p7>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s5-supply = <&vreg_vph_pwr>;
+
+		vreg_s5j_1p2: smps5 {
+			regulator-name = "vreg_s5j_1p2";
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1j_0p8: ldo1 {
+			regulator-name = "vreg_l1j_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2j_1p2: ldo2 {
+			regulator-name = "vreg_l2j_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3j_0p8: ldo3 {
+			regulator-name = "vreg_l3j_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&gpu {
+	status = "okay";
+
+	zap-shader {
+		firmware-name = "qcom/x1e80100/hp/omnibook-x14/qcdxkmsuc8380.mbn";
+	};
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	keyboard@3a {
+		compatible = "hid-over-i2c";
+		reg = <0x3a>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		pinctrl-0 = <&kybd_default>;
+		pinctrl-names = "default";
+
+		wakeup-source;
+	};
+
+	touchpad@15 {
+		compatible = "hid-over-i2c";
+		reg = <0x15>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		pinctrl-0 = <&tpad_default>;
+		pinctrl-names = "default";
+
+		wakeup-source;
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	/* type-c PS8830 Retimer #2 0x8 */
+	/* is active on Windows */
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	typec-mux@8 {
+		compatible = "parade,ps8830";
+		reg = <0x08>;
+
+		clocks = <&rpmhcc RPMH_RF_CLK3>;
+
+		vdd-supply = <&vreg_rtmr0_1p15>;
+		vdd33-supply = <&vreg_rtmr0_3p3>;
+		vdd33-cap-supply = <&vreg_rtmr0_3p3>;
+		vddar-supply = <&vreg_rtmr0_1p15>;
+		vddat-supply = <&vreg_rtmr0_1p15>;
+		vddio-supply = <&vreg_rtmr0_1p8>;
+
+		reset-gpios = <&pm8550_gpios 10 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&rtmr0_default>;
+		pinctrl-names = "default";
+
+		orientation-switch;
+		retimer-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				retimer_ss0_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss0_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				retimer_ss0_ss_in: endpoint {
+					remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				retimer_ss0_con_sbu_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss0_con_sbu_in>;
+				};
+			};
+		};
+	};
+};
+
+&i2c4 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	/* is active on Windows */
+};
+
+&i2c5 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	eusb3_repeater: redriver@47 {
+		compatible = "nxp,ptn3222";
+		reg = <0x47>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+
+		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb3_reset_n>;
+		pinctrl-names = "default";
+
+	};
+};
+
+&i2c7 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	typec-mux@8 {
+		compatible = "parade,ps8830";
+		reg = <0x8>;
+
+		clocks = <&rpmhcc RPMH_RF_CLK4>;
+
+		vdd-supply = <&vreg_rtmr1_1p15>;
+		vdd33-supply = <&vreg_rtmr1_3p3>;
+		vdd33-cap-supply = <&vreg_rtmr1_3p3>;
+		vddar-supply = <&vreg_rtmr1_1p15>;
+		vddat-supply = <&vreg_rtmr1_1p15>;
+		vddio-supply = <&vreg_rtmr1_1p8>;
+
+		reset-gpios = <&tlmm 176 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&rtmr1_default>;
+		pinctrl-names = "default";
+
+		orientation-switch;
+		retimer-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				retimer_ss1_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss1_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				retimer_ss1_ss_in: endpoint {
+					remote-endpoint = <&usb_1_ss1_qmpphy_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				retimer_ss1_con_sbu_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss1_con_sbu_in>;
+				};
+			};
+
+		};
+	};
+};
+
+&i2c8 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	touchscreen@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l15b_1p8>;
+
+		pinctrl-0 = <&ts0_default>;
+		pinctrl-names = "default";
+	};
+};
+
+&i2c9 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	/* is active on Windows */
+};
+
+&lpass_tlmm {
+	spkr_01_sd_n_active: spkr-01-sd-n-active-state {
+		pins = "gpio12";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+};
+
+&lpass_vamacro {
+	pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
+	pinctrl-names = "default";
+
+	vdd-micb-supply = <&vreg_l1b_1p8>;
+	qcom,dmic-sample-rate = <4800000>;
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	data-lanes = <0 1>;
+};
+
+&mdss_dp1 {
+	status = "okay";
+};
+
+&mdss_dp1_out {
+	data-lanes = <0 1>;
+};
+
+&mdss_dp3 {
+	compatible = "qcom,x1e80100-dp";
+	/delete-property/ #sound-dai-cells;
+
+	status = "okay";
+
+	aux-bus {
+		panel {
+			compatible = "edp-panel";
+			power-supply = <&vreg_edp_3p3>;
+
+			backlight = <&backlight>;
+
+			port {
+				edp_panel_in: endpoint {
+					remote-endpoint = <&mdss_dp3_out>;
+				};
+			};
+		};
+	};
+
+	ports {
+		port@1 {
+			reg = <1>;
+
+			mdss_dp3_out: endpoint {
+				data-lanes = <0 1 2 3>;
+				link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+				remote-endpoint = <&edp_panel_in>;
+			};
+		};
+	};
+};
+
+&mdss_dp3_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pcie4 {
+	perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie4_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie4_phy {
+	vdda-phy-supply = <&vreg_l3i_0p8>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&pcie4_port0 {
+	wifi@0 {
+		compatible = "pci17cb,1107";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+		vddaon-supply = <&vreg_pmu_aon_0p8>;
+		vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+		vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn_0p8>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p8>;
+	};
+};
+
+&pcie6a {
+	perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
+
+	vddpe-3v3-supply = <&vreg_nvme>;
+
+	pinctrl-0 = <&pcie6a_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie6a_phy {
+	vdda-phy-supply = <&vreg_l1d_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pm8550_gpios {
+	rtmr0_default: rtmr0-reset-n-active-state {
+		pins = "gpio10";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+
+	usb0_3p3_reg_en: usb0-3p3-reg-en-state {
+		pins = "gpio11";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+};
+
+&pm8550ve_8_gpios {
+	misc_3p3_reg_en: misc-3p3-reg-en-state {
+		pins = "gpio6";
+		function = "normal";
+		bias-disable;
+		drive-push-pull;
+		input-disable;
+		output-enable;
+		power-source = <1>; /* 1.8 V */
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+	};
+};
+
+&pm8550ve_9_gpios {
+	usb0_1p8_reg_en: usb0-1p8-reg-en-state {
+		pins = "gpio8";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+};
+
+&pmc8380_3_gpios {
+	edp_bl_en: edp-bl-en-state {
+		pins = "gpio4";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		input-disable;
+		output-enable;
+	};
+
+	edp_bl_reg_en: edp-bl-reg-en-state {
+		pins = "gpio10";
+		function = "normal";
+	};
+
+};
+
+&pmk8550_gpios {
+	edp_bl_pwm: edp-bl-pwm-state {
+		pins = "gpio5";
+		function = "func3";
+	};
+};
+
+&pmk8550_pwm {
+	status = "okay";
+};
+
+&pmc8380_5_gpios {
+	usb0_pwr_1p15_reg_en: usb0-pwr-1p15-reg-en-state {
+		pins = "gpio8";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+};
+
+&qupv3_0 {
+	status = "okay";
+};
+
+&qupv3_1 {
+	status = "okay";
+};
+
+&qupv3_2 {
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/x1e80100/hp/omnibook-x14/qcadsp8380.mbn",
+			"qcom/x1e80100/hp/omnibook-x14/adsp_dtbs.elf";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/x1e80100/hp/omnibook-x14/qccdsp8380.mbn",
+			"qcom/x1e80100/hp/omnibook-x14/cdsp_dtbs.elf";
+
+	status = "okay";
+};
+
+&smb2360_0_eusb2_repeater {
+	vdd18-supply = <&vreg_l3d_1p8>;
+	vdd3-supply = <&vreg_l2b_3p0>;
+
+	status = "okay";
+};
+
+&smb2360_1_eusb2_repeater {
+	vdd18-supply = <&vreg_l3d_1p8>;
+	vdd3-supply = <&vreg_l14b_3p0>;
+
+	status = "okay";
+};
+
+&swr0 {
+	pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	/* WSA8845, Left Speaker */
+	left_spkr: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrLeft";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <1 2 3 7 10 13>;
+	};
+
+	/* WSA8845, Right Speaker */
+	right_spkr: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrRight";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <4 5 6 7 11 13>;
+	};
+};
+
+&swr1 {
+	status = "okay";
+
+	/* WCD9385 RX */
+	wcd_rx: codec@0,4 {
+		compatible = "sdw20217010d00";
+		reg = <0 4>;
+		qcom,rx-port-mapping = <1 2 3 4 5>;
+	};
+};
+
+&swr2 {
+	status = "okay";
+
+	/* WCD9385 TX */
+	wcd_tx: codec@0,3 {
+		compatible = "sdw20217010d00";
+		reg = <0 3>;
+		qcom,tx-port-mapping = <2 2 3 4>;
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <34 2>, /* Unused */
+			       <44 4>, /* SPI (TPM) */
+			       <72 2>, /* Secure EC I2C connection (?) */
+			       <238 1>; /* UFS Reset */
+
+	bt_en_default: bt-en-sleep {
+		pins = "gpio116";
+		function = "gpio";
+		output-low;
+		bias-disable;
+		drive-strength = <16>;
+	};
+
+	edp_reg_en: edp-reg-en-state {
+		pins = "gpio70";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	eusb3_reset_n: eusb3-reset-n-state {
+		pins = "gpio6";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	hall_int_n_default: hall-int-n-state {
+		pins = "gpio92";
+		function = "gpio";
+		bias-disable;
+	};
+
+	kybd_default: kybd-default-state {
+		pins = "gpio67";
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	nvme_reg_en: nvme-reg-en-state {
+		pins = "gpio18";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pcie4_default: pcie4-default-state {
+		clkreq-n-pins {
+			pins = "gpio147";
+			function = "pcie4_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio146";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio148";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	pcie6a_default: pcie6a-default-state {
+		clkreq-n-pins {
+			pins = "gpio153";
+			function = "pcie6a_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio152";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio154";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	rtmr1_default: rtmr1-reset-n-active-state {
+		pins = "gpio176";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tpad_default: tpad-default-state {
+		pins = "gpio3";
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	ts0_default: ts0-default-state {
+		int-n-pins {
+			pins = "gpio51";
+			function = "gpio";
+			bias-pull-up;
+		};
+
+		reset-n-pins {
+			pins = "gpio48";
+			function = "gpio";
+			output-high;
+			drive-strength = <16>;
+		};
+	};
+
+	usb1_pwr_1p15_reg_en: usb1-pwr-1p15-reg-en-state {
+		pins = "gpio188";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	usb1_pwr_1p8_reg_en: usb1-pwr-1p8-reg-en-state {
+		pins = "gpio175";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	usb1_pwr_3p3_reg_en: usb1-pwr-3p3-reg-en-state {
+		pins = "gpio186";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wcd_default: wcd-reset-n-active-state {
+		pins = "gpio191";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+
+	wcn_sw_en: wcn-sw-en-state {
+		pins = "gpio214";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wcn_wlan_bt_en: wcn-wlan-bt-en-state {
+		pins = "gpio116", "gpio117";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&uart14 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn6855-bt";
+		max-speed = <3200000>;
+
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn_0p8>;
+		vddaon-supply = <&vreg_pmu_aon_0p8>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p8>;
+		vddbtcmx-supply = <&vreg_pmu_btcmx_0p8>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
+	};
+};
+
+&usb_1_ss0_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	phys = <&smb2360_0_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_1_ss0_qmpphy {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l1j_0p8>;
+
+	status = "okay";
+};
+
+&usb_1_ss0 {
+	status = "okay";
+};
+
+&usb_1_ss0_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_ss0_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss0_hs_in>;
+};
+
+&usb_1_ss0_qmpphy_out {
+	remote-endpoint = <&retimer_ss0_ss_in>;
+};
+
+&usb_1_ss1_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	phys = <&smb2360_1_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_1_ss1_qmpphy {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l2d_0p9>;
+
+	status = "okay";
+};
+
+&usb_1_ss1 {
+	status = "okay";
+};
+
+&usb_1_ss1_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_ss1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss1_hs_in>;
+};
+
+&usb_1_ss1_qmpphy_out {
+	remote-endpoint = <&retimer_ss1_ss_in>;
+};
+
+&usb_mp {
+	status = "okay";
+};
+
+&usb_mp_dwc3 {
+	phys = <&usb_mp_hsphy0>, <&usb_mp_qmpphy0>;
+	phy-names = "usb2-0", "usb3-0";
+};
+
+&usb_mp_hsphy0 {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb3_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy0 {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3c_0p8>;
+
+	status = "okay";
+};

-- 
2.43.0

Re: [PATCH v3 3/3] arm64: dts: qcom: x1e80100-hp-x14: dt for HP Omnibook X Laptop 14

[Konrad Dybcio]

On 2.12.2024 8:41 PM, Jens Glathe via B4 Relay wrote:
> From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
> 
> Introduce device tree for the HP Omnibook X Laptop 14-fe0750ng
> (hp-omnibook-x14). It is a Laptop based on the Qualcomm Snapdragon
> X Elite SoC. There seem to be other SKUs, some with Wifi-7 (WCN7850)
> instead of Wifi-6E (WCN6855). This dt explicitly supports WCN6855,
> I haven't found a good way yet to describe both.
> 
> PDF link: https://www8.hp.com/h20195/V2/GetPDF.aspx/c08989140
> 
> Supported features:
> 
> - Keyboard (no function keys though)
> - Display
> - PWM brightness control (works via brightnessctl)
> - Touchpad
> - Touchscreen
> - PCIe ports (pcie4, pcie6a)
> - USB type-c, type-a
> - WCN6855 Wifi-6E
> - WCN6855 Bluetooth
> - ADSP and CDSP
> - X1 GPU
> - GPIO Keys (Lid switch)
> - Audio definition (works via USB)
> 
> Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad

Re: (subset) [PATCH v3 0/3] arm64: dts: qcom: x1e80100-hp-x14: dt for HP Omnibook X Laptop 14

[Bjorn Andersson]

On Mon, 02 Dec 2024 20:41:28 +0100, Jens Glathe wrote:
> Introduce device tree for the HP Omnibook X Laptop 14-fe0750ng
> (hp-omnibook-x14). It is a Laptop based on the Qualcomm Snapdragon
> X Elite SoC. There seem to be other SKUs, some with Wifi-7 (WCN7850)
> instead of Wifi-6E (WCN6855). This dt explicitly supports WCN6855,
> I haven't found a good way yet to describe both.
> 
> PDF link: https://www8.hp.com/h20195/V2/GetPDF.aspx/c08989140
> 
> [...]

Applied, thanks!

[1/3] dt-bindings: arm: qcom: Add HP Omnibook X 14
      commit: 6ba121febf852718afa48d0ca062a74fa7cafe1c
[3/3] arm64: dts: qcom: x1e80100-hp-x14: dt for HP Omnibook X Laptop 14
      commit: 6f18b8d4142c3174e08136f0b1ce400441d53330

Best regards,
-- 
Bjorn Andersson <andersson@kernel.org>