* 2.6.12 can not support via rhine?
@ 2005-06-23 4:17 guorke
2005-06-23 4:21 ` guorke
2005-06-23 18:09 ` Bjorn Helgaas
0 siblings, 2 replies; 4+ messages in thread
From: guorke @ 2005-06-23 4:17 UTC (permalink / raw)
To: linux-kernel
hi
when i reboot use 2.6.11,it's ok.
but when i use 2.6.12 kernel, i get this:
via rhine device dose not seem to be present , delaying eth0 initialzation..
but in 2.6.11, it's say ok, I must say i have add via rhine support.
this following is difference output demsg :
diff -y dmesg_2.6.11 dmesg_2.6.12
VFS: Mounted root (ext3 filesystem) readonly. VFS:
Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 220k freed |
Freeing unused kernel memory: 224k freed
kjournald starting. Commit interval 5 seconds <
EXT3 FS on hda1, internal journal EXT3
FS on hda1, internal journal
Adding 265064k swap on /dev/hda2. Priority:-1 extents:1 Adding
265064k swap on /dev/hda2. Priority:-1 extents:1
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald <
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 12 <
PCI: setting IRQ 12 as level-triggered <
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 12 (level, low) -> <
eth0: VIA Rhine II at 0x1e800, 00:05:5d:fb:7d:29, IRQ 12. <
eth0: MII PHY found at address 8, status 0x782d advertising 0 <
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 <
like no via rhine.
Thanks
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: 2.6.12 can not support via rhine?
2005-06-23 4:17 2.6.12 can not support via rhine? guorke
@ 2005-06-23 4:21 ` guorke
2005-06-23 5:04 ` guorke
2005-06-23 18:09 ` Bjorn Helgaas
1 sibling, 1 reply; 4+ messages in thread
From: guorke @ 2005-06-23 4:21 UTC (permalink / raw)
To: linux-kernel
VFS: Mounted root (ext3 filesystem) readonly. |VFS: Mounted root (ext3
filesystem) readonly.
better is
Freeing unused kernel memory: 220k freed | Freeing unused kernel
memory... freed
kjournald starting. Commit interval 5 seconds <
EXT3 FS on hda1, internal journal | EXT3 FS on hda1,
internal journal
Adding 265064k swap on /dev/hda2..... | Adding 265064k swap
/dev/hda2. ...
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004.. <
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 12 <
PCI: setting IRQ 12 as level-triggered <
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 12 (level, low) -> <
eth0: VIA Rhine II at 0x1e800, 00:05:5d:fb:7d:29, IRQ 12. <
eth0: MII PHY found at address 8, status 0x782d advertising <
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 <
On 6/23/05, guorke <gourke@gmail.com> wrote:
> hi
> when i reboot use 2.6.11,it's ok.
> but when i use 2.6.12 kernel, i get this:
>
> via rhine device dose not seem to be present , delaying eth0 initialzation..
> but in 2.6.11, it's say ok, I must say i have add via rhine support.
> this following is difference output demsg :
> diff -y dmesg_2.6.11 dmesg_2.6.12
>
> VFS: Mounted root (ext3 filesystem) readonly. VFS:
> Mounted root (ext3 filesystem) readonly.
> Freeing unused kernel memory: 220k freed |
> Freeing unused kernel memory: 224k freed
> kjournald starting. Commit interval 5 seconds <
> EXT3 FS on hda1, internal journal EXT3
> FS on hda1, internal journal
> Adding 265064k swap on /dev/hda2. Priority:-1 extents:1 Adding
> 265064k swap on /dev/hda2. Priority:-1 extents:1
> via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald <
> ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 12 <
> PCI: setting IRQ 12 as level-triggered <
> ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 12 (level, low) -> <
> eth0: VIA Rhine II at 0x1e800, 00:05:5d:fb:7d:29, IRQ 12. <
> eth0: MII PHY found at address 8, status 0x782d advertising 0 <
> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 <
>
> like no via rhine.
>
> Thanks
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: 2.6.12 can not support via rhine?
2005-06-23 4:21 ` guorke
@ 2005-06-23 5:04 ` guorke
0 siblings, 0 replies; 4+ messages in thread
From: guorke @ 2005-06-23 5:04 UTC (permalink / raw)
To: linux-kernel
who can give helps?
Thanks
On 6/23/05, guorke <gourke@gmail.com> wrote:
> VFS: Mounted root (ext3 filesystem) readonly. |VFS: Mounted root (ext3
> filesystem) readonly.
> better is
> Freeing unused kernel memory: 220k freed | Freeing unused kernel
> memory... freed
> kjournald starting. Commit interval 5 seconds <
> EXT3 FS on hda1, internal journal | EXT3 FS on hda1,
> internal journal
> Adding 265064k swap on /dev/hda2..... | Adding 265064k swap
> /dev/hda2. ...
> via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004.. <
> ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 12 <
> PCI: setting IRQ 12 as level-triggered <
> ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 12 (level, low) -> <
> eth0: VIA Rhine II at 0x1e800, 00:05:5d:fb:7d:29, IRQ 12. <
> eth0: MII PHY found at address 8, status 0x782d advertising <
> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 <
>
>
>
> On 6/23/05, guorke <gourke@gmail.com> wrote:
> > hi
> > when i reboot use 2.6.11,it's ok.
> > but when i use 2.6.12 kernel, i get this:
> >
> > via rhine device dose not seem to be present , delaying eth0 initialzation..
> > but in 2.6.11, it's say ok, I must say i have add via rhine support.
> > this following is difference output demsg :
> > diff -y dmesg_2.6.11 dmesg_2.6.12
> >
> > VFS: Mounted root (ext3 filesystem) readonly. VFS:
> > Mounted root (ext3 filesystem) readonly.
> > Freeing unused kernel memory: 220k freed |
> > Freeing unused kernel memory: 224k freed
> > kjournald starting. Commit interval 5 seconds <
> > EXT3 FS on hda1, internal journal EXT3
> > FS on hda1, internal journal
> > Adding 265064k swap on /dev/hda2. Priority:-1 extents:1 Adding
> > 265064k swap on /dev/hda2. Priority:-1 extents:1
> > via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald <
> > ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 12 <
> > PCI: setting IRQ 12 as level-triggered <
> > ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 12 (level, low) -> <
> > eth0: VIA Rhine II at 0x1e800, 00:05:5d:fb:7d:29, IRQ 12. <
> > eth0: MII PHY found at address 8, status 0x782d advertising 0 <
> > eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 <
> >
> > like no via rhine.
> >
> > Thanks
> >
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: 2.6.12 can not support via rhine?
2005-06-23 4:17 2.6.12 can not support via rhine? guorke
2005-06-23 4:21 ` guorke
@ 2005-06-23 18:09 ` Bjorn Helgaas
1 sibling, 0 replies; 4+ messages in thread
From: Bjorn Helgaas @ 2005-06-23 18:09 UTC (permalink / raw)
To: guorke; +Cc: linux-kernel
On Wednesday 22 June 2005 10:17 pm, guorke wrote:
> when i reboot use 2.6.11,it's ok.
> but when i use 2.6.12 kernel, i get this:
>
> via rhine device dose not seem to be present , delaying eth0 initialzation..
> but in 2.6.11, it's say ok, I must say i have add via rhine support.
Are you sure your 2.6.12 .config has CONFIG_VIA_RHINE set?
Could you post the complete 2.6.11 and 2.6.12 dmesg logs? I couldn't
quite follow the excerpts your posted.
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2005-06-23 18:13 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-06-23 4:17 2.6.12 can not support via rhine? guorke
2005-06-23 4:21 ` guorke
2005-06-23 5:04 ` guorke
2005-06-23 18:09 ` Bjorn Helgaas
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox