From: Baolu Lu <baolu.lu@linux.intel.com>
To: Jacob Pan <jacob.jun.pan@linux.intel.com>,
LKML <linux-kernel@vger.kernel.org>,
iommu@lists.linux.dev, Joerg Roedel <joro@8bytes.org>
Cc: baolu.lu@linux.intel.com, David Woodhouse <dwmw2@infradead.org>,
Raj Ashok <ashok.raj@intel.com>,
"Tian, Kevin" <kevin.tian@intel.com>, Yi Liu <yi.l.liu@intel.com>,
stable@vger.kernel.org, Sukumar Ghorai <sukumar.ghorai@intel.com>
Subject: Re: [PATCH] iommu/vt-d: Fix PASID directory pointer coherency
Date: Sat, 4 Feb 2023 11:43:01 +0800 [thread overview]
Message-ID: <de4d0617-ceef-efca-69f1-a095ce91588e@linux.intel.com> (raw)
In-Reply-To: <20230203220714.1283383-1-jacob.jun.pan@linux.intel.com>
On 2023/2/4 6:07, Jacob Pan wrote:
> On platforms that do not support IOMMU Extended capability bit 0
> Page-walk Coherency, CPU caches are not snooped when IOMMU is accessing
> any translation structures. IOMMU access goes only directly to
> memory. Intel IOMMU code was missing a flush for the PASID table
> directory that resulted in the unrecoverable fault as shown below.
Thanks for the fix.
> This patch adds a clflush when activating a PASID table directory.
> There's no need to do clflush of the PASID directory pointer when we
> deactivate a context entry in that IOMMU hardware will not see the old
> PASID directory pointer after we clear the context entry.
>
> [ 0.555386] DMAR: DRHD: handling fault status reg 3
> [ 0.555805] DMAR: [DMA Read NO_PASID] Request device [00:0d.2] fault addr 0x1026a4000 [fault reason 0x51] SM: Present bit in Directory Entry is clear
> [ 0.556348] DMAR: Dump dmar1 table entries for IOVA 0x1026a4000
> [ 0.556348] DMAR: scalable mode root entry: hi 0x0000000102448001, low 0x0000000101b3e001
> [ 0.556348] DMAR: context entry: hi 0x0000000000000000, low 0x0000000101b4d401
> [ 0.556348] DMAR: pasid dir entry: 0x0000000101b4e001
> [ 0.556348] DMAR: pasid table entry[0]: 0x0000000000000109
> [ 0.556348] DMAR: pasid table entry[1]: 0x0000000000000001
> [ 0.556348] DMAR: pasid table entry[2]: 0x0000000000000000
> [ 0.556348] DMAR: pasid table entry[3]: 0x0000000000000000
> [ 0.556348] DMAR: pasid table entry[4]: 0x0000000000000000
> [ 0.556348] DMAR: pasid table entry[5]: 0x0000000000000000
> [ 0.556348] DMAR: pasid table entry[6]: 0x0000000000000000
> [ 0.556348] DMAR: pasid table entry[7]: 0x0000000000000000
> [ 0.556348] DMAR: PTE not present at level 4
>
> Cc: <stable@vger.kernel.org>
> Reported-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
> Signed-off-by: Ashok Raj <ashok.raj@intel.com>
> Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Add a Fixes tag so that people know how far this fix should be back
ported.
> ---
> drivers/iommu/intel/iommu.c | 6 ++++++
> 1 file changed, 6 insertions(+)
>
> diff --git a/drivers/iommu/intel/iommu.c b/drivers/iommu/intel/iommu.c
> index 59df7e42fd53..b4878c7ac008 100644
> --- a/drivers/iommu/intel/iommu.c
> +++ b/drivers/iommu/intel/iommu.c
> @@ -1976,6 +1976,12 @@ static int domain_context_mapping_one(struct dmar_domain *domain,
> pds = context_get_sm_pds(table);
> context->lo = (u64)virt_to_phys(table->table) |
> context_pdts(pds);
> + /*
> + * Scalable-mode PASID directory pointer is not snooped if the
> + * coherent bit is not set.
> + */
> + if (!ecap_coherent(iommu->ecap))
> + clflush_cache_range(table->table, sizeof(void *));
This isn't comprehensive. The clflush should be called whenever the
pasid directory table is allocated or updated.
>
> /* Setup the RID_PASID field: */
> context_set_sm_rid2pasid(context, PASID_RID2PASID);
Best regards,
baolu
next prev parent reply other threads:[~2023-02-04 3:43 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-02-03 22:07 [PATCH] iommu/vt-d: Fix PASID directory pointer coherency Jacob Pan
2023-02-04 3:43 ` Baolu Lu [this message]
2023-02-06 17:25 ` Jacob Pan
2023-02-07 0:41 ` Tian, Kevin
2023-02-07 18:09 ` Jacob Pan
2023-02-07 7:10 ` Baolu Lu
2023-02-07 18:08 ` Jacob Pan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=de4d0617-ceef-efca-69f1-a095ce91588e@linux.intel.com \
--to=baolu.lu@linux.intel.com \
--cc=ashok.raj@intel.com \
--cc=dwmw2@infradead.org \
--cc=iommu@lists.linux.dev \
--cc=jacob.jun.pan@linux.intel.com \
--cc=joro@8bytes.org \
--cc=kevin.tian@intel.com \
--cc=linux-kernel@vger.kernel.org \
--cc=stable@vger.kernel.org \
--cc=sukumar.ghorai@intel.com \
--cc=yi.l.liu@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox