Re: [PATCH v4 2/2] mtd: rawnand: Add NAND controller support on Intel LGM SoC

["Ramuthevar, Vadivel MuruganX" <vadivel.muruganx.ramuthevar@linux.intel.com>]

Hi Boris,

On 30/4/2020 9:01 pm, Boris Brezillon wrote:
> On Thu, 30 Apr 2020 14:36:00 +0200
> Boris Brezillon <boris.brezillon@collabora.com> wrote:
> 
>> On Thu, 30 Apr 2020 17:07:03 +0800
>> "Ramuthevar, Vadivel MuruganX"
>> <vadivel.muruganx.ramuthevar@linux.intel.com> wrote:
>>
>>>>>> The question is, is it the same value we have in nand_pa or it is
>>>>>> different?
>>>>>>         
>>>>> Different address which is 0xE1400000 NAND_BASE_PHY address.
>>>>
>>>> Then why didn't you tell me they didn't match when I suggested to pass
>>>
>>> sorry, because you keep asking nand_pa after that only I realized that.
>>>    
>>>> nand_pa? So now the question is, what does this address represent?
>>>
>>>                  EBU-MODULE
>>>    _________     _______________________
>>> |         |   |            |NAND CTRL  |
>>> | FPI BUS |==>| CS0(0x174) | 0xE100    ( 0xE14/0xE1C) NAND_PHY_BASE
>>> |_________|   |_CS1(0x17C)_|__________ |
>>>
>>> EBU_CONRTROLLER_BASE : 0xE0F0_0000
>>> HSNAND_BASE: 0xE100_0000
>>> NAND_CS0: 0xE140_0000
>>> NAND_CS1: 0xE1C0_0000
>>>
>>> MEM_REGION_BASE_CS0: 0x17400 (internal to ebu controller )
>>> MEM_REGION_BASE_CS1: 0x17C00
>>>    
>>
>> Hm, I wonder if we shouldn't use a 'ranges' property to describe this
>> address translation. Something like
>>
>> 	ebu@xxx {
>> 		ranges = <0x17400000 0xe1400000 0x1000>,
>> 			 <0x17c00000 0xe1c00000 0x1000>;
>> 		reg = <0x17400000>, <0x17c00000>;
>> 		reg-names = "cs-0", "cs-1";
>> 	}
>>
>> The translated address (0xE1X00000) will be available in res->start,
>> and the non-translated one (0x17X00000) can be retrieved with
>> of_get_address(). All you'd have to do then would be calculate the
>> mask:
>>
>> 	mask = (translated_address & original_address) >> 22;
>> 	num_comp_bits = fls(mask);
>> 	WARN_ON(mask != GENMASK(num_comp_bits - 1, 0));
>>
>> Which allows you to properly set the ADDR_SEL() register without
>> relying on some hardcoded values:
>>
>> 	writel(original_address | EBU_ADDR_SEL_REGEN |
>> 	       EBU_ADDR_COMP_BITS(num_comp_bits),
>> 	       ebu_host->ebu + EBU_ADDR_SEL(csid));
>>
>> That's quite important if we want to merge the xway NAND driver with
>> this one.
> 
> Looks like the translation is done at the FPI bus declaration level (see
> [1]). We really need to see the big picture to take a wise decision
> about the bindings. Would you mind pasting your dsti/dts files
> somewhere? It feels like the NAND controller is a sub-part of a more
> generic 'memory' controller, in which case the NAND controller should be
> declared as a child of this generic memory bus (called localbus in [1],
> but maybe EBU is more accurate).
> 
> [1]https://github.com/xieyaxiongfly/Atheros_CSI_tool_OpenWRT_src/blob/master/target/linux/lantiq/files-4.14/arch/mips/boot/dts/vr9.dtsi#L162


  ebu_nand: ebu_nand@e0f00000 {
                  compatible = "intel,lgm-ebu-nand";
                  reg = <0xe0f00000 0x100
                  0xe1000000 0x300
                  0xe1400000 0x80000
                  0xe1c00000 0x10000>;
                  reg-names = "ebunand", "hsnand", "nand_cs0", nand_cs1";
                  dmas = <&dma0 8>, <&dma0 9>;
                  dma-names = "ebu_rx", "ebu_tx";
                  clocks =  <&cgu0 LGM_GCLK_EBU>;
          };


	 &ebu_nand {
	         status = "disabled";
	        nand,cs = <1>;
	        nand-ecc-mode = "hw";
	        pinctrl-names = "default";
	        pinctrl-0 = <&ebu_nand_base &ebu_cs1>;
	};

>