[LTP] [PATCH] commands/mkswap: Added new testcase to test mkswap(8).

[Guangwen Feng <fenggw-fnst@cn.fujitsu.com>]

Hi!
Thanks for review!

On 2015/11/09 10:00, Lei Li wrote:
>> +setup()
>> +{
>> +    tst_require_root
>> +
>> +    tst_check_cmds losetup free mkswap
>> +
>> +    tst_tmpdir
>> +
>> +    TST_CLEANUP=cleanup
>> +
>> +    tst_acquire_device
>> +
>> +    local path=`losetup -a | grep "$TMPDIR"  | awk '{print $3}' | \
>> +        cut -d '(' -f2 | cut -d ')' -f1`
>> +    DEVICE_SIZE=$((`ls -l $path | awk '{print $5}'`/1024))
> Hi!
>     This testcase uses a loop device instead of a block device, but tst_acquire_device may offer you a block device, /opt/ltp/runltp -b /dev/sdb1 for example, then, "path" may be invilidate, and syntax error occurs in the line :
> 
> DEVICE_SIZE=$((`ls -l $path | awk '{print $5}'`/1024))
> 
> So, examination whether the "path" is validate is necessary.
> 

Indeed, I missed the condition of block device.
I think I could use DEVICE_SIZE=$((`blockdev --getsize64 $TST_DEVICE`/1024)) instead of via path.

>> +
>> +    PAGE_SIZE=`getconf PAGE_SIZE`
>> +}
>> +
>> +cleanup()
>> +{
>> +    tst_release_device
>> +
>> +    tst_rmdir
>> +}
>> +
>> +mkswap_verify()
>> +{
>> +    local ret=0
>> +
>> +    local before=`free | grep "Swap" | awk '{print $2}'`
>> +
>> +    if [ -z "$4" ]; then
>> +        local swapsize=$DEVICE_SIZE
>> +    else
>> +        local swapsize=$4
>> +    fi
>> +
>> +    if [ "$1" = "-p" ]; then
>> +        local pagesize=$2
>> +    else
>> +        local pagesize=$PAGE_SIZE
>> +    fi
>> +
>> +    if [ "$1" = "-L" ]; then
>> +        local swap_op="-L"
>> +        local swapfile=$2
>> +    elif [ "$1" = "-U" ]; then
>> +        local swap_op="-U"
>> +        local swapfile=$2
>> +    else
>> +        local swap_op=""
>> +        local swapfile=$3
>> +    fi
>> +
>> +    swapon $swap_op $swapfile 2>/dev/null
>> +    if [ $? -ne 0 ]; then
>> +        tst_resm TINFO "can not do swapon on $swapfile."
>> +        if [ $pagesize -ne $PAGE_SIZE ]; then
>> +            return $ret
>> +        fi
>> +
>> +        if [ $swapsize -gt $DEVICE_SIZE ]; then
>> +            return $ret
>> +        fi
>> +    fi
>> +
>> +    local after=`free | grep "Swap" | awk '{print $2}'`
>> +
>> +    local est=16
>> +    if [ $((after-before)) -lt $((swapsize-pagesize/1024-est)) ] || \
>> +        [ $((after-before)) -gt $((swapsize-pagesize/1024+est)) ]; then
>> +        ret=1
>> +    fi
> 
> How do you get this formula? I'm a newbie here :-)
> 

I just compare device size used for swap with the actual increment of swap.
The increment should be equal to the device size minus a page size, but in some cases, the result fluctuates.

>> +
>> +    swapoff $swap_op $swapfile 2>/dev/null
>> +    if [ $? -ne 0 ]; then
>> +        tst_resm TINFO "can not do swapoff on $swapfile."
>> +    fi
>> +
>> +    return $ret
>> +}
>> +
>> +mkswap_test()
>> +{
>> +    local mkswap_op=$1
>> +    local op_arg=$2
>> +    local device=$3
>> +    local size=$4
>> +
>> +    local mkswap_cmd="mkswap $mkswap_op $op_arg $device $size"
>> +
>> +    ${mkswap_cmd} >temp 2>&1
>> +    if [ $? -ne 0 ]; then
>> +        grep -q -E "unknown option|invalid option|Usage" temp
>> +        if [ $? -eq 0 ]; then
>> +            tst_resm TCONF "'${mkswap_cmd}' not supported."
>> +            return
>> +        else
>> +            tst_resm TFAIL "'${mkswap_cmd}' failed."
>> +            cat temp
>> +            return
>> +        fi
>> +    fi
>> +
>> +    if [ -n "$device" ]; then
>> +        mkswap_verify "$mkswap_op" "$op_arg" "$device" "$size"
>> +        if [ $? -ne 0 ]; then
>> +            tst_resm TFAIL "'${mkswap_cmd}' failed, not expected."
>> +            return
>> +        fi
>> +    fi
>> +
>> +    tst_resm TPASS "'${mkswap_cmd}' passed."
>> +}
>> +
>> +test1()
>> +{
>> +    mkswap_test "" "" "$TST_DEVICE"
>> +}
>> +
>> +test2()
>> +{
>> +    mkswap_test "" "" "$TST_DEVICE" "10000"
>> +}
>> +
>> +test3()
>> +{
>> +    mkswap_test "-f" "" "$TST_DEVICE" "30000"
>> +}
> The size of loop device is 20000 currently, but there is no guarantee that value will not be changed in the future. "10000" and "30000" may be inappropriate at that time.In my opinion, it is more reasonable like this:
> 
> test2()
> {
>     mkswap_test "" "" "$TST_DEVICE" "$((DEVICE_SIZE-10000))"
> }
> 
> test3()
> {
>     mkswap_test "-f" "" "$TST_DEVICE" "$((DEVICE_SIZE+10000))"
> }

Yes, it's more reasonably, thanks.

>> +
>> +test4()
>> +{
>> +    mkswap_test "-c" "" "$TST_DEVICE"
>> +}
>> +
>> +test5()
>> +{
>> +    mkswap_test "-p" "2048" "$TST_DEVICE"
>> +}
>> +
>> +test6()
>> +{
>> +    mkswap_test "-L" "testswap" "$TST_DEVICE"
>> +}
>> +
>> +test7()
>> +{
>> +    mkswap_test "-v1" "" "$TST_DEVICE"
>> +}
>> +
>> +test8()
>> +{
>> +    mkswap_test "-U" "ffffffff-ffff-ffff-ffff-ffffffffffff" "$TST_DEVICE"
>> +}
>> +
>> +test9()
>> +{
>> +    mkswap_test "-V"
>> +}
>> +
>> +test10()
>> +{
>> +    mkswap_test "-h"
>> +}
>> +
>> +setup
>> +
>> +for i in $(seq 1 ${TST_TOTAL})
>> +do
>> +    test$i
>> +done
>> +
>> +tst_exit
>>
>