[LTP] [PATCH v3] commands/mkswap: Added new testcase to test mkswap(8).

[Guangwen Feng <fenggw-fnst@cn.fujitsu.com>]

Hi!

Thanks for your review!
I will modify the test case according to your suggestion.

Best Regards,
Guangwen Feng

On 2015/11/17 00:31, Cyril Hrubis wrote:
> Hi!
>> +TCID=mkswap01
>> +TST_TOTAL=10
>> +. test.sh
>> +
>> +setup()
>> +{
>> +	tst_require_root
>> +
>> +	tst_check_cmds blkid blockdev free mkswap
>                         ^
> 			uuidgen is missing here
> 
>> +	tst_tmpdir
>> +
>> +	TST_CLEANUP=cleanup
>> +
>> +	tst_acquire_device
>> +
>> +	UUID=`uuidgen`
>> +
>> +	DEVICE_SIZE=$((`blockdev --getsize64 $TST_DEVICE`/1024))
>> +
>> +	PAGE_SIZE=`getconf PAGE_SIZE`
>> +}
>> +
>> +cleanup()
>> +{
>> +	tst_release_device
>> +
>> +	tst_rmdir
>> +}
>> +
>> +mkswap_verify()
>> +{
>> +	local mkswap_op=$1
>> +	local op_arg=$2
>> +	local device=$3
>> +	local size=$4
>> +
>> +	local ret=0
>> +
>> +	local before=`free | grep "Swap" | awk '{print $2}'`
> 
> We can do better with:
> 
> awk '/SwapTotal/ {print $2}' /proc/meminfo
> 
> No need to call free and no need to use grep :).
> 
>> +	local swapsize=${4:-$DEVICE_SIZE}
>> +
>> +	if [ "$mkswap_op" = "-p" ]; then
>> +		local pagesize=$op_arg
>> +	else
>> +		local pagesize=$PAGE_SIZE
>> +	fi
>> +
>> +	if [ "$mkswap_op" = "-L" ] || [ "$mkswap_op" = "-U" ]; then
>> +		local swapfile=$op_arg
>> +	else
>> +		mkswap_op=
>> +		local swapfile=$device
>> +	fi
> 
> Can you actually pass the device for the test instead of passing
> $TST_DEVICE which is kind of pointles when you can use $TST_DEVICE in
> the mkswap_test() for the mkswap command?
> 
>> +	swapon $mkswap_op $swapfile 2>/dev/null
>> +	if [ $? -ne 0 ]; then
>> +		tst_resm TINFO "Can not do swapon on $swapfile."
>> +		if [ $pagesize -ne $PAGE_SIZE ]; then
>> +			tst_resm TINFO "Page size specified by 'mkswap -p' \
>> +is not equal to system's page size."
>> +			tst_resm TINFO "Swapon failed expectedly."
>> +			return $ret
>                               ^
>                         Just do return 0 here, it's more confusing as
> 			it should be as this is.
>> +		fi
>> +
>> +		if [ $swapsize -gt $DEVICE_SIZE ]; then
>> +			tst_resm TINFO "Device size specified by 'mkswap' \
>> +greater than real size."
>> +			tst_resm TINFO "Swapon failed expectedly."
>> +			return $ret
> 
> Here as well.
> 
>> +		fi
>> +
>> +		tst_resm TINFO "Swapon failed unexpectedly."
>> +		return 1
>> +	fi
>> +
>> +	local after=`free | grep "Swap" | awk '{print $2}'`
> 
> Here you can simplify the command as well.
> 
>> +	local est=16
> 
> You shoud intialize the ret=0 here.
> 
>> +	if [ $((after-before)) -lt $((swapsize-pagesize/1024-est)) ] || \
>> +		[ $((after-before)) -gt $((swapsize-pagesize/1024+est)) ]; then
>> +		ret=1
>> +	fi
> 
> What is the story behind the est? It should probably be worth comment
> when the size could be 16kB off or at least on which system does this
> happens.
> 
> And I would compute the difference only once and store it to a variable,
> but that is minor.
> 
>> +	swapoff $mkswap_op $swapfile 2>/dev/null
>> +	if [ $? -ne 0 ]; then
>> +		tst_resm TINFO "Can not do swapoff on $swapfile."
>> +	fi
>> +
>> +	return $ret
> 
> Otherwise it looks good.
>