Re: [net-next,PATCH 2/2] net: stmmac: dwmac-stm32: stm32: add management of stm32mp25 for stm32

[Christophe ROULLIER <christophe.roullier@foss.st.com>]

On 6/19/24 15:14, Marek Vasut wrote:
> On 6/19/24 9:41 AM, Christophe ROULLIER wrote:
>
> Hi,
>
>>>>>>>> +static int stm32mp2_configure_syscfg(struct 
>>>>>>>> plat_stmmacenet_data *plat_dat)
>>>>>>>> +{
>>>>>>>> +    struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
>>>>>>>> +    u32 reg = dwmac->mode_reg;
>>>>>>>> +    int val = 0;
>>>>>>>> +
>>>>>>>> +    switch (plat_dat->mac_interface) {
>>>>>>>> +    case PHY_INTERFACE_MODE_MII:
>>>>>>>> +        break;
>>>>>>>
>>>>>>> dwmac->enable_eth_ck does not apply to MII mode ? Why ?
>>>>>>
>>>>>> It is like MP1 and MP13, nothing to set in syscfg register for 
>>>>>> case MII mode wo crystal.
>>>>>
>>>>> Have a look at STM32MP15xx RM0436 Figure 83. Peripheral clock 
>>>>> distribution for Ethernet.
>>>>>
>>>>> If RCC (top-left corner of the figure) generates 25 MHz MII clock 
>>>>> (yellow line) on eth_clk_fb (top-right corner), can I set 
>>>>> ETH_REF_CLK_SEL to position '1' and ETH_SEL[2] to '0' and feed ETH 
>>>>> (right side) clk_rx_i input with 25 MHz clock that way ?
>>>>>
>>>>> I seems like this should be possible, at least theoretically. Can 
>>>>> you check with the hardware/silicon people ?
>>>> No it is not possible (it will work if speed (and frequency) is 
>>>> fixed 25Mhz=100Mbps, but for speed 10Mbps (2,5MHz) it will not work.
>>>
>>> Could the pll4_p_ck or pll3_q_ck generate either 25 MHz or 2.5 MHz 
>>> as needed in that case ? Then it would work, right ?
>>
>> Yes you can set frequency you want for pll4 or pll3, if you set 25MHz 
>> and auto-negotiation of speed is 100Mbps it should work (pad ETH_CK 
>> of 25MHz clock the PHY and eth_clk_fb set to 25MHz for clk_RX)
>>
>> but if autoneg of speed is 10Mbps, then 2.5MHz is needed for clk_RX 
>> (you will provide 25Mhz)
>
> What if:
>
> - Aneg is 10 Mbps
> - PLL4_P_CK/PLL3_Q_CK = 2.5 MHz
> - ETH_REF_CLK_SEL = 1
> - ETH_SEL[2] = 0
>
> ?
>
> Then, clk_rx_i is 2.5 MHz, right ?
Yes that right
>
> Does this configuration work ?
For me no, because PHY Ethernet Oscillator/cristal need in PAD 25Mhz or 
50Mhz, I think it is does not work if oscillator frequency provided is 
2.5MHz (To my knowledge there is no Ethernet PHY which have oscillator 
working to 2.5MHz)
>
>> . For RMII case, frequency from pll (eth_clk_fb) is automatically 
>> adjust in function of speed value, thanks to diviser /2, /20 with 
>> mac_speed_o.