From: "Michael Chan" <mchan@broadcom.com>
To: davem@davemloft.net
Cc: jgarzik@pobox.com, netdev@oss.sgi.com
Subject: [PATCH 2.6.12-rc5 7/9] tg3: Add loopback test
Date: Thu, 26 May 2005 10:59:06 -0700 [thread overview]
Message-ID: <1117130346.3744.59.camel@rh4> (raw)
In-Reply-To: <1117128795.3744.22.camel@rh4>
[-- Attachment #1: Type: text/plain, Size: 133 bytes --]
The test will loopback one packet in MAC loopback mode and verify the
packet data.
Signed-off-by: Michael Chan <mchan@broadcom.com>
[-- Attachment #2: tg3-d7.patch --]
[-- Type: text/x-patch, Size: 3431 bytes --]
diff -Nru d6/drivers/net/tg3.c d7/drivers/net/tg3.c
--- d6/drivers/net/tg3.c 2005-05-25 12:59:31.000000000 -0700
+++ d7/drivers/net/tg3.c 2005-05-25 12:59:38.000000000 -0700
@@ -7576,6 +7576,117 @@
return err;
}
+static int tg3_test_loopback(struct tg3 *tp)
+{
+ u32 mac_mode, send_idx, rx_start_idx, rx_idx, tx_idx, opaque_key;
+ u32 desc_idx;
+ struct sk_buff *skb, *rx_skb;
+ u8 *tx_data;
+ dma_addr_t map;
+ int num_pkts, tx_len, rx_len, i, err;
+ struct tg3_rx_buffer_desc *desc;
+
+ if (!netif_running(tp->dev))
+ return -ENODEV;
+
+ err = -EIO;
+
+ tg3_abort_hw(tp, 1);
+
+ /* Clearing this flag to keep interrupts disabled */
+ tp->tg3_flags &= ~TG3_FLAG_INIT_COMPLETE;
+ tg3_reset_hw(tp);
+
+ mac_mode = (tp->mac_mode & ~MAC_MODE_PORT_MODE_MASK) |
+ MAC_MODE_PORT_INT_LPBACK | MAC_MODE_LINK_POLARITY |
+ MAC_MODE_PORT_MODE_GMII;
+ tw32(MAC_MODE, mac_mode);
+
+ tx_len = 1514;
+ skb = dev_alloc_skb(tx_len);
+ tx_data = skb_put(skb, tx_len);
+ memcpy(tx_data, tp->dev->dev_addr, 6);
+ memset(tx_data + 6, 0x0, 8);
+
+ tw32(MAC_RX_MTU_SIZE, tx_len + 4);
+
+ for (i = 14; i < tx_len; i++)
+ tx_data[i] = (u8) (i & 0xff);
+
+ map = pci_map_single(tp->pdev, skb->data, tx_len, PCI_DMA_TODEVICE);
+
+ tw32_f(HOSTCC_MODE, tp->coalesce_mode | HOSTCC_MODE_ENABLE |
+ HOSTCC_MODE_NOW);
+
+ udelay(10);
+
+ rx_start_idx = tp->hw_status->idx[0].rx_producer;
+
+ send_idx = 0;
+ num_pkts = 0;
+
+ tg3_set_txd(tp, send_idx, map, tx_len, 0, 1);
+
+ send_idx++;
+ num_pkts++;
+
+ tw32_tx_mbox(MAILBOX_SNDHOST_PROD_IDX_0 + TG3_64BIT_REG_LOW, send_idx);
+ tr32(MAILBOX_SNDHOST_PROD_IDX_0 + TG3_64BIT_REG_LOW);
+
+ udelay(10);
+
+ for (i = 0; i < 10; i++) {
+ tw32_f(HOSTCC_MODE, tp->coalesce_mode | HOSTCC_MODE_ENABLE |
+ HOSTCC_MODE_NOW);
+
+ udelay(10);
+
+ tx_idx = tp->hw_status->idx[0].tx_consumer;
+ rx_idx = tp->hw_status->idx[0].rx_producer;
+ if ((tx_idx == send_idx) &&
+ (rx_idx == (rx_start_idx + num_pkts)))
+ break;
+ }
+
+ pci_unmap_single(tp->pdev, map, tx_len, PCI_DMA_TODEVICE);
+ dev_kfree_skb(skb);
+
+ if (tx_idx != send_idx)
+ goto out;
+
+ if (rx_idx != rx_start_idx + num_pkts)
+ goto out;
+
+ desc = &tp->rx_rcb[rx_start_idx];
+ desc_idx = desc->opaque & RXD_OPAQUE_INDEX_MASK;
+ opaque_key = desc->opaque & RXD_OPAQUE_RING_MASK;
+ if (opaque_key != RXD_OPAQUE_RING_STD)
+ goto out;
+
+ if ((desc->err_vlan & RXD_ERR_MASK) != 0 &&
+ (desc->err_vlan != RXD_ERR_ODD_NIBBLE_RCVD_MII))
+ goto out;
+
+ rx_len = ((desc->idx_len & RXD_LEN_MASK) >> RXD_LEN_SHIFT) - 4;
+ if (rx_len != tx_len)
+ goto out;
+
+ rx_skb = tp->rx_std_buffers[desc_idx].skb;
+
+ map = pci_unmap_addr(&tp->rx_std_buffers[desc_idx], mapping);
+ pci_dma_sync_single_for_cpu(tp->pdev, map, rx_len, PCI_DMA_FROMDEVICE);
+
+ for (i = 14; i < tx_len; i++) {
+ if (*(rx_skb->data + i) != (u8) (i & 0xff))
+ goto out;
+ }
+ err = 0;
+
+ /* tg3_free_rings will unmap and free the rx_skb */
+out:
+ return err;
+}
+
static void tg3_self_test(struct net_device *dev, struct ethtool_test *etest,
u64 *data)
{
@@ -7613,6 +7724,10 @@
etest->flags |= ETH_TEST_FL_FAILED;
data[3] = 1;
}
+ if (tg3_test_loopback(tp) != 0) {
+ etest->flags |= ETH_TEST_FL_FAILED;
+ data[4] = 1;
+ }
tg3_halt(tp, RESET_KIND_SHUTDOWN, 1);
if (netif_running(dev)) {
next prev parent reply other threads:[~2005-05-26 17:59 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-05-26 17:33 [PATCH 2.6.12-rc5 0/9] tg3: Add ethtool selftest Michael Chan
2005-05-26 17:56 ` [PATCH 2.6.12-rc5 1/9] tg3: Add basic selftest infrastructure Michael Chan
2005-05-26 17:57 ` [PATCH 2.6.12-rc5 2/9] tg3: Add nvram test Michael Chan
2005-05-26 17:57 ` [PATCH 2.6.12-rc5 3/9] tg3: Add link test Michael Chan
2005-05-26 17:58 ` [PATCH 2.6.12-rc5 4/9] tg3: Add parameter to tg3_halt Michael Chan
2005-05-26 17:58 ` [PATCH 2.6.12-rc5 5/9] tg3: Add register test Michael Chan
2005-05-26 17:58 ` [PATCH 2.6.12-rc5 6/9] tg3: Add memory test Michael Chan
2005-05-26 17:59 ` Michael Chan [this message]
2005-05-26 17:59 ` [PATCH 2.6.12-rc5 8/9] tg3: Add interrupt test Michael Chan
2005-05-26 18:00 ` [PATCH 2.6.12-rc5 9/9] tg3: Fix bug in tg3_load_firmware_cpu Michael Chan
2005-05-26 19:13 ` Jeff Garzik
2005-05-26 22:10 ` David S. Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1117130346.3744.59.camel@rh4 \
--to=mchan@broadcom.com \
--cc=davem@davemloft.net \
--cc=jgarzik@pobox.com \
--cc=netdev@oss.sgi.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).