From: Dan Williams <dcbw@redhat.com>
To: breed@users.sourceforge.net
Cc: netdev@vger.kernel.org, jgarzik@pobox.com,
"John W. Linville" <linville@tuxdriver.com>,
networkmanager-list@gnome.org
Subject: [2.6.15 patch] wireless/airo: add IWENCODEEXT and IWAUTH support
Date: Mon, 30 Jan 2006 11:58:00 -0500 [thread overview]
Message-ID: <1138640281.12551.5.camel@dhcp83-115.boston.redhat.com> (raw)
This patch adds IWENCODEEXT and IWAUTH support to the airo driver for
WEP and unencrypted operation. No WPA though. It allows the driver to
operate more willingly with wpa_supplicant and NetworkManager.
Signed-off-by: Dan Williams <dcbw@redhat.com>
--- a/drivers/net/wireless/airo.c 2006-01-30 10:14:23.000000000 -0500
+++ b/drivers/net/wireless/airo.c 2006-01-30 11:05:15.000000000 -0500
@@ -5802,11 +5802,13 @@ static int airo_set_wap(struct net_devic
Cmd cmd;
Resp rsp;
APListRid APList_rid;
- static const unsigned char bcast[ETH_ALEN] = { 255, 255, 255, 255, 255, 255 };
+ static const u8 any[ETH_ALEN] = { 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF };
+ static const u8 off[ETH_ALEN] = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 };
if (awrq->sa_family != ARPHRD_ETHER)
return -EINVAL;
- else if (!memcmp(bcast, awrq->sa_data, ETH_ALEN)) {
+ else if (!memcmp(any, awrq->sa_data, ETH_ALEN) ||
+ !memcmp(off, awrq->sa_data, ETH_ALEN)) {
memset(&cmd, 0, sizeof(cmd));
cmd.cmd=CMD_LOSE_SYNC;
if (down_interruptible(&local->sem))
@@ -6297,6 +6299,267 @@ static int airo_get_encode(struct net_de
/*------------------------------------------------------------------*/
/*
+ * Wireless Handler : set extended Encryption parameters
+ */
+static int airo_set_encodeext(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ struct airo_info *local = dev->priv;
+ struct iw_point *encoding = &wrqu->encoding;
+ struct iw_encode_ext *ext = (struct iw_encode_ext *)extra;
+ CapabilityRid cap_rid; /* Card capability info */
+ int perm = ( encoding->flags & IW_ENCODE_TEMP ? 0 : 1 );
+ u16 currentAuthType = local->config.authType;
+ int idx, key_len, alg = ext->alg; /* Check encryption mode */
+ wep_key_t key;
+
+ /* Is WEP supported ? */
+ readCapabilityRid(local, &cap_rid, 1);
+ /* Older firmware doesn't support this...
+ if(!(cap_rid.softCap & 2)) {
+ return -EOPNOTSUPP;
+ } */
+ readConfigRid(local, 1);
+
+ /* Determine and validate the key index */
+ idx = encoding->flags & IW_ENCODE_INDEX;
+ if (idx) {
+ if (idx < 1 || idx > ((cap_rid.softCap & 0x80) ? 4:1))
+ return -EINVAL;
+ idx--;
+ } else
+ idx = get_wep_key(local, 0xffff);
+
+ if (encoding->flags & IW_ENCODE_DISABLED)
+ alg = IW_ENCODE_ALG_NONE;
+
+ /* Just setting the transmit key? */
+ if (ext->ext_flags & IW_ENCODE_EXT_SET_TX_KEY) {
+ set_wep_key(local, idx, NULL, 0, perm, 1);
+ } else {
+ /* Set the requested key first */
+ memset(key.key, 0, MAX_KEY_SIZE);
+ switch (alg) {
+ case IW_ENCODE_ALG_NONE:
+ key.len = 0;
+ break;
+ case IW_ENCODE_ALG_WEP:
+ if (ext->key_len > MIN_KEY_SIZE) {
+ key.len = MAX_KEY_SIZE;
+ } else if (ext->key_len > 0) {
+ key.len = MIN_KEY_SIZE;
+ } else {
+ return -EINVAL;
+ }
+ key_len = min (ext->key_len, key.len);
+ memcpy(key.key, ext->key, key_len);
+ break;
+ default:
+ return -EINVAL;
+ }
+ /* Send the key to the card */
+ set_wep_key(local, idx, key.key, key.len, perm, 1);
+ }
+
+ /* Read the flags */
+ if(encoding->flags & IW_ENCODE_DISABLED)
+ local->config.authType = AUTH_OPEN; // disable encryption
+ if(encoding->flags & IW_ENCODE_RESTRICTED)
+ local->config.authType = AUTH_SHAREDKEY; // Only Both
+ if(encoding->flags & IW_ENCODE_OPEN)
+ local->config.authType = AUTH_ENCRYPT; // Only Wep
+ /* Commit the changes to flags if needed */
+ if (local->config.authType != currentAuthType)
+ set_bit (FLAG_COMMIT, &local->flags);
+
+ return -EINPROGRESS;
+}
+
+
+/*------------------------------------------------------------------*/
+/*
+ * Wireless Handler : get extended Encryption parameters
+ */
+static int airo_get_encodeext(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ struct airo_info *local = dev->priv;
+ struct iw_point *encoding = &wrqu->encoding;
+ struct iw_encode_ext *ext = (struct iw_encode_ext *)extra;
+ CapabilityRid cap_rid; /* Card capability info */
+ int idx, max_key_len;
+
+ /* Is it supported ? */
+ readCapabilityRid(local, &cap_rid, 1);
+ if(!(cap_rid.softCap & 2)) {
+ return -EOPNOTSUPP;
+ }
+ readConfigRid(local, 1);
+
+ max_key_len = encoding->length - sizeof(*ext);
+ if (max_key_len < 0)
+ return -EINVAL;
+
+ idx = encoding->flags & IW_ENCODE_INDEX;
+ if (idx) {
+ if (idx < 1 || idx > ((cap_rid.softCap & 0x80) ? 4:1))
+ return -EINVAL;
+ idx--;
+ } else
+ idx = get_wep_key(local, 0xffff);
+
+ encoding->flags = idx + 1;
+ memset(ext, 0, sizeof(*ext));
+
+ /* Check encryption mode */
+ switch(local->config.authType) {
+ case AUTH_ENCRYPT:
+ encoding->flags = IW_ENCODE_ALG_WEP | IW_ENCODE_ENABLED;
+ break;
+ case AUTH_SHAREDKEY:
+ encoding->flags = IW_ENCODE_ALG_WEP | IW_ENCODE_ENABLED;
+ break;
+ default:
+ case AUTH_OPEN:
+ encoding->flags = IW_ENCODE_ALG_NONE | IW_ENCODE_DISABLED;
+ break;
+ }
+ /* We can't return the key, so set the proper flag and return zero */
+ encoding->flags |= IW_ENCODE_NOKEY;
+ memset(extra, 0, 16);
+
+ /* Copy the key to the user buffer */
+ ext->key_len = get_wep_key(local, idx);
+ if (ext->key_len > 16) {
+ ext->key_len=0;
+ }
+
+ return 0;
+}
+
+
+/*------------------------------------------------------------------*/
+/*
+ * Wireless Handler : set extended authentication parameters
+ */
+static int airo_set_auth(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu, char *extra)
+{
+ struct airo_info *local = dev->priv;
+ struct iw_param *param = &wrqu->param;
+ u16 currentAuthType = local->config.authType;
+
+ switch (param->flags & IW_AUTH_INDEX) {
+ case IW_AUTH_WPA_VERSION:
+ case IW_AUTH_CIPHER_PAIRWISE:
+ case IW_AUTH_CIPHER_GROUP:
+ case IW_AUTH_KEY_MGMT:
+ case IW_AUTH_RX_UNENCRYPTED_EAPOL:
+ case IW_AUTH_PRIVACY_INVOKED:
+ /*
+ * airo does not use these parameters
+ */
+ break;
+
+ case IW_AUTH_DROP_UNENCRYPTED:
+ if (param->value) {
+ /* Only change auth type if unencrypted */
+ if (currentAuthType == AUTH_OPEN)
+ local->config.authType = AUTH_ENCRYPT;
+ } else {
+ local->config.authType = AUTH_OPEN;
+ }
+
+ /* Commit the changes to flags if needed */
+ if (local->config.authType != currentAuthType)
+ set_bit (FLAG_COMMIT, &local->flags);
+ break;
+
+ case IW_AUTH_80211_AUTH_ALG: {
+ /* FIXME: What about AUTH_OPEN? This API seems to
+ * disallow setting our auth to AUTH_OPEN.
+ */
+ if (param->value & IW_AUTH_ALG_SHARED_KEY) {
+ local->config.authType = AUTH_SHAREDKEY;
+ } else if (param->value & IW_AUTH_ALG_OPEN_SYSTEM) {
+ local->config.authType = AUTH_ENCRYPT;
+ } else
+ return -EINVAL;
+ break;
+
+ /* Commit the changes to flags if needed */
+ if (local->config.authType != currentAuthType)
+ set_bit (FLAG_COMMIT, &local->flags);
+ }
+
+ case IW_AUTH_WPA_ENABLED:
+ /* Silently accept disable of WPA */
+ if (param->value > 0)
+ return -EOPNOTSUPP;
+ break;
+
+ default:
+ return -EOPNOTSUPP;
+ }
+ return -EINPROGRESS;
+}
+
+
+/*------------------------------------------------------------------*/
+/*
+ * Wireless Handler : get extended authentication parameters
+ */
+static int airo_get_auth(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu, char *extra)
+{
+ struct airo_info *local = dev->priv;
+ struct iw_param *param = &wrqu->param;
+ u16 currentAuthType = local->config.authType;
+
+ switch (param->flags & IW_AUTH_INDEX) {
+ case IW_AUTH_DROP_UNENCRYPTED:
+ switch (currentAuthType) {
+ case AUTH_SHAREDKEY:
+ case AUTH_ENCRYPT:
+ param->value = 1;
+ break;
+ default:
+ param->value = 0;
+ break;
+ }
+ break;
+
+ case IW_AUTH_80211_AUTH_ALG:
+ switch (currentAuthType) {
+ case AUTH_SHAREDKEY:
+ param->value = IW_AUTH_ALG_SHARED_KEY;
+ break;
+ case AUTH_ENCRYPT:
+ default:
+ param->value = IW_AUTH_ALG_OPEN_SYSTEM;
+ break;
+ }
+ break;
+
+ case IW_AUTH_WPA_ENABLED:
+ param->value = 0;
+ break;
+
+ default:
+ return -EOPNOTSUPP;
+ }
+ return 0;
+}
+
+
+/*------------------------------------------------------------------*/
+/*
* Wireless Handler : set Tx-Power
*/
static int airo_set_txpow(struct net_device *dev,
@@ -7051,6 +7314,15 @@ static const iw_handler airo_handler[]
(iw_handler) airo_get_encode, /* SIOCGIWENCODE */
(iw_handler) airo_set_power, /* SIOCSIWPOWER */
(iw_handler) airo_get_power, /* SIOCGIWPOWER */
+ (iw_handler) NULL, /* -- hole -- */
+ (iw_handler) NULL, /* -- hole -- */
+ (iw_handler) NULL, /* SIOCSIWGENIE */
+ (iw_handler) NULL, /* SIOCGIWGENIE */
+ (iw_handler) airo_set_auth, /* SIOCSIWAUTH */
+ (iw_handler) airo_get_auth, /* SIOCGIWAUTH */
+ (iw_handler) airo_set_encodeext, /* SIOCSIWENCODEEXT */
+ (iw_handler) airo_get_encodeext, /* SIOCGIWENCODEEXT */
+ (iw_handler) NULL, /* SIOCSIWPMKSA */
};
/* Note : don't describe AIROIDIFC and AIROOLDIDIFC in here.
next reply other threads:[~2006-01-30 16:58 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-01-30 16:58 Dan Williams [this message]
2006-01-30 19:04 ` [2.6.15 patch] wireless/airo: add IWENCODEEXT and IWAUTH support Robert Love
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1138640281.12551.5.camel@dhcp83-115.boston.redhat.com \
--to=dcbw@redhat.com \
--cc=breed@users.sourceforge.net \
--cc=jgarzik@pobox.com \
--cc=linville@tuxdriver.com \
--cc=netdev@vger.kernel.org \
--cc=networkmanager-list@gnome.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox