From: Matthias Hentges <oe@hentges.net>
To: Stephen Hemminger <shemminger@osdl.org>
Cc: Jeff Garzik <jeff@garzik.org>, Andrew Morton <akpm@osdl.org>,
Linux Kernel <linux-kernel@vger.kernel.org>,
Netdev List <netdev@vger.kernel.org>
Subject: Re: sky2 (was Re: 2.6.18-mm2)
Date: Sun, 08 Oct 2006 19:00:01 +0200 [thread overview]
Message-ID: <1160326801.4575.27.camel@mhcln03> (raw)
In-Reply-To: <20061008092001.0c83a359@localhost.localdomain>
[-- Attachment #1.1: Type: text/plain, Size: 1191 bytes --]
Am Sonntag, den 08.10.2006, 09:20 -0700 schrieb Stephen Hemminger:
> On Sun, 08 Oct 2006 15:41:45 +0200
> Matthias Hentges <oe@hentges.net> wrote:
[...]
> > I have verified this behavior (works fine w/o debug patch, freezes with
> > patch applied) with:
> > - 2.6.19-rc1-git4
> > - 2.6.18-git something
> > - 2.6.18-mm3
> >
>
> Does 2.6.18 work?
2.6.18 does not require the patch ( in fact, the patch won't apply at
all) and thus does not freeze when the NIC goes down.
> What is the PCI config of the device (lspci -vvvx)?
I've attached the lspci dump of both onboard sky2 NICs.
> What is the chip version (dmesg | grep sky2)?
>
+root@mhcln01:..patches/generic/coretemp >dmesg |grep sky2
[ 34.833453] sky2 v1.7 addr 0xfa9fc000 irq 17 Yukon-EC (0xb6) rev 2
[ 34.833527] sky2 eth0: addr 00:17:31:f4:f1:8c
[ 34.833663] sky2 v1.7 addr 0xfa8fc000 irq 16 Yukon-EC (0xb6) rev 2
[ 34.833729] sky2 eth1: addr 00:17:31:f4:f7:cc
[ 42.165687] sky2 eth1: enabling interface
[ 43.847972] sky2 eth1: Link is up at 100 Mbps, full duplex, flow
control both
--
Matthias 'CoreDump' Hentges
My OS: Debian SID. Geek by Nature, Linux by Choice
[-- Attachment #1.2: lspci-vvvv_sky2-1.txt --]
[-- Type: text/plain, Size: 1533 bytes --]
03:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller (rev 20)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8053 Gigabit Ethernet controller PCIe (Asus)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 216
Region 0: Memory at fa8fc000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at a800 [size=256]
Expansion ROM at fa8c0000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Address: 00000000fee0100c Data: 4152
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <256ns, L1 unlimited
Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
[-- Attachment #1.3: lspci-vvvv_sky2-2.txt --]
[-- Type: text/plain, Size: 1533 bytes --]
04:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller (rev 20)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8053 Gigabit Ethernet controller PCIe (Asus)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 217
Region 0: Memory at fa9fc000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at b800 [size=256]
Expansion ROM at fa9c0000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Address: 00000000fee0300c Data: 414a
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <256ns, L1 unlimited
Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
[-- Attachment #2: Dies ist ein digital signierter Nachrichtenteil --]
[-- Type: application/pgp-signature, Size: 189 bytes --]
next prev parent reply other threads:[~2006-10-08 17:00 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20060928155053.7d8567ae.akpm@osdl.org>
2006-09-28 23:07 ` sky2 (was Re: 2.6.18-mm2) Jeff Garzik
2006-09-28 23:19 ` Stephen Hemminger
2006-09-30 0:26 ` Matthias Hentges
2006-10-04 2:57 ` Matthias Hentges
2006-10-04 3:26 ` Stephen Hemminger
2006-10-07 19:48 ` Matthias Hentges
2006-10-08 13:41 ` Matthias Hentges
2006-10-08 16:20 ` Stephen Hemminger
2006-10-08 17:00 ` Matthias Hentges [this message]
2006-10-10 0:02 ` Beber
2006-09-28 23:25 ` Andrew Morton
2006-09-28 23:30 ` Stephen Hemminger
2006-09-29 16:04 ` Andrea Gelmini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1160326801.4575.27.camel@mhcln03 \
--to=oe@hentges.net \
--cc=akpm@osdl.org \
--cc=jeff@garzik.org \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=shemminger@osdl.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).