* Re: Realtek 8111c weirdness problems, apic/msi, and normal bug [not found] <1207407804.14885.27.camel@localhost> @ 2008-04-06 6:23 ` Andrew Morton 2008-04-06 14:06 ` Francois Romieu 0 siblings, 1 reply; 9+ messages in thread From: Andrew Morton @ 2008-04-06 6:23 UTC (permalink / raw) To: Kasper Sandberg; +Cc: LKML Mailinglist, linux-acpi, netdev Let's add some cc's. On Sat, 05 Apr 2008 17:03:24 +0200 Kasper Sandberg <lkml@metanurb.dk> wrote: > Hello. > > I have a Gigabyte-X48-DQ6 motherboard which contains two realtek 8111c > pci express gigabit ethernet controllers. > > The driver for these are r8169 > > To cut to the results that matters(IMO) most, is that on .25-rc8-git3, > the driver detects these cards, both of them, on different interrupts, > however, none of the nics work if i have both msi and apic enabled. If i > boot with pci=nomsi, and apic is enabled, both ports work (however one > "insignificant" bug remains), if i boot with noapic boot parameter, but > msi is enabled, both controllers are again found, and they work, however > that insignificant bug is also present here. > > The insignificant bug is, that one of the interfaces appears to always > report as link up, despite me not having any cable in it. > > So apparently the conflict is if i have BOTH apic and msi. > > That leads me to a question, untill this is resolved, which > configuration do i want? apic with no msi, or msi with no apic? > > I also have some more information, however i do not know if its useful > at all: On a .23 livecd, which has both msi and apic, something > different happens. What happens is that both controllers are detected, > however only 1 of them works, ethtool reports that the working > controller properly detects link up/down, and that its TP with 1gbit. > This is the ethtool output for the .23 livecd with apic and msi: > Settings for eth0: > Supported ports: [ TP ] > Supported link modes: 10baseT/Half 10baseT/Full > 100baseT/Half 100baseT/Full > 1000baseT/Full > Supports auto-negotiation: Yes > Advertised link modes: 10baseT/Half 10baseT/Full > 100baseT/Half 100baseT/Full > 1000baseT/Full > Advertised auto-negotiation: Yes > Speed: 1000Mb/s > Duplex: Full > Port: Twisted Pair > PHYAD: 0 > Transceiver: internal > Auto-negotiation: on > Supports Wake-on: pumbg > Wake-on: g > Current message level: 0x00000033 (51) > Link detected: yes > > > Settings for eth1: > Supported ports: [ FIBRE ] > Supported link modes: 1000baseT/Full > Supports auto-negotiation: Yes > Advertised link modes: Not reported > Advertised auto-negotiation: Yes > Speed: 1000Mb/s > Duplex: Full > Port: FIBRE > PHYAD: 0 > Transceiver: internal > Auto-negotiation: on > Supports Wake-on: pumbg > Wake-on: g > Current message level: 0x00000033 (51) > Link detected: no > > and as you can see, eth1 is completely messed up, thinking its fibre, > and stuff.. > > it appears that on this configuration, both nic's were registered > in /proc/interrupts as IO-APIC-fasteoi. > --- > > I realize that more information will probably be needed to fix this bug, > however, as you probably will want to cc linux-netdev or apic/msi or > what it is, i will refrain from posting that now. > > However, i can pretty much provide/try anything, so what would you want > me to get? > /proc/interrupts, dmesg, ethtool on .25 apic/nomsi? > /proc/interrupts, dmesg, ethtool on .25 msi/noapic? > /proc/interrupts, dmesg, ethtool on .25 msi/apic? > i also saw a strange message with .25 msi/apic, where when i rmmod r8169 > and modprobe it again, it couldnt parse something, should i try get this > again? > > > In any case, just let me know what information you want, or patches you > wish me to test, and it will be done. > ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Realtek 8111c weirdness problems, apic/msi, and normal bug 2008-04-06 6:23 ` Realtek 8111c weirdness problems, apic/msi, and normal bug Andrew Morton @ 2008-04-06 14:06 ` Francois Romieu 2008-04-07 4:09 ` Kasper Sandberg 0 siblings, 1 reply; 9+ messages in thread From: Francois Romieu @ 2008-04-06 14:06 UTC (permalink / raw) To: Kasper Sandberg; +Cc: Andrew Morton, LKML Mailinglist, linux-acpi, netdev Andrew Morton <akpm@linux-foundation.org> : [...] > > /proc/interrupts, dmesg, ethtool on .25 apic/nomsi? Complete dmesg and lspci -vvxn for a start. -- Ueimor ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Realtek 8111c weirdness problems, apic/msi, and normal bug 2008-04-06 14:06 ` Francois Romieu @ 2008-04-07 4:09 ` Kasper Sandberg 2008-04-10 12:17 ` Kasper Sandberg 0 siblings, 1 reply; 9+ messages in thread From: Kasper Sandberg @ 2008-04-07 4:09 UTC (permalink / raw) To: Francois Romieu; +Cc: Andrew Morton, LKML Mailinglist, linux-acpi, netdev Hello. I apologize, but it will have to wait a few days, as the fan on the graphics card just broke, and it overheats almost instantly. I will post as soon as possible, sorry for the inconvenience. On Sun, 2008-04-06 at 16:06 +0200, Francois Romieu wrote: > Andrew Morton <akpm@linux-foundation.org> : > [...] > > > /proc/interrupts, dmesg, ethtool on .25 apic/nomsi? > > Complete dmesg and lspci -vvxn for a start. > ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Realtek 8111c weirdness problems, apic/msi, and normal bug 2008-04-07 4:09 ` Kasper Sandberg @ 2008-04-10 12:17 ` Kasper Sandberg 2008-04-11 1:11 ` Kasper Sandberg 0 siblings, 1 reply; 9+ messages in thread From: Kasper Sandberg @ 2008-04-10 12:17 UTC (permalink / raw) To: Francois Romieu; +Cc: Andrew Morton, LKML Mailinglist, linux-acpi, netdev On Mon, 2008-04-07 at 06:09 +0200, Kasper Sandberg wrote: > Hello. > > I apologize, but it will have to wait a few days, as the fan on the > graphics card just broke, and it overheats almost instantly. > > I will post as soon as possible, sorry for the inconvenience. > > On Sun, 2008-04-06 at 16:06 +0200, Francois Romieu wrote: > > Andrew Morton <akpm@linux-foundation.org> : > > [...] > > > > /proc/interrupts, dmesg, ethtool on .25 apic/nomsi? > > > > Complete dmesg and lspci -vvxn for a start. Okay, the box is up again, sorry for the delay.. hmm, is this dmesg cut off? (its right after booting, but maybe the buffer isnt big enough?) 000 - 0xc0318df8 (2147 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. CPA: page pool initialized 1 of 1 pages preallocated SLUB: Genslabs=12, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 Calibrating delay using timer specific routine.. 3201.59 BogoMIPS (lpj=1600795) Mount-cache hash table entries: 512 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 512K Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. using mwait in idle threads. Compat vDSO mapped to ffffe000. CPU: Intel(R) Celeron(R) CPU 420 @ 1.60GHz stepping 01 Checking 'hlt' instruction... OK. Freeing SMP alternatives: 0k freed net_namespace: 152 bytes NET: Registered protocol family 16 PCI: PCI BIOS revision 3.00 entry at 0xfb6c0, last bus=7 PCI: Using configuration type 1 Setting up standard PCI resources SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO PCI: Transparent bridge - 0000:00:1e.0 PCI: Discovered primary peer bus ff [IRQ] PCI: Using IRQ router PIIX/ICH [8086/2916] at 0000:00:1f.0 hpet clockevent registered PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: 0xe4000000-0xe6ffffff PREFETCH window: 0x00000000d0000000-0x00000000dfffffff PCI: Bridge: 0000:00:06.0 IO window: 9000-9fff MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.0 IO window: a000-afff MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.3 IO window: b000-bfff MEM window: 0xe9100000-0xe91fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.4 IO window: c000-cfff MEM window: 0xe7000000-0xe7ffffff PREFETCH window: 0x00000000e9000000-0x00000000e90fffff PCI: Bridge: 0000:00:1c.5 IO window: d000-dfff MEM window: 0xe8000000-0xe8ffffff PREFETCH window: 0x00000000e9200000-0x00000000e92fffff PCI: Bridge: 0000:00:1e.0 IO window: disabled. MEM window: 0xe9300000-0xe93fffff PREFETCH window: disabled. PCI: setting IRQ 10 as level-triggered PCI: Found IRQ 10 for device 0000:00:01.0 PCI: Sharing IRQ 10 with 0000:00:06.0 PCI: Sharing IRQ 10 with 0000:00:1a.0 PCI: Sharing IRQ 10 with 0000:00:1c.0 PCI: Sharing IRQ 10 with 0000:00:1c.4 PCI: Sharing IRQ 10 with 0000:05:00.0 PCI: Setting latency timer of device 0000:00:01.0 to 64 PCI: Found IRQ 10 for device 0000:00:06.0 PCI: Sharing IRQ 10 with 0000:00:01.0 PCI: Sharing IRQ 10 with 0000:00:1a.0 PCI: Sharing IRQ 10 with 0000:00:1c.0 PCI: Sharing IRQ 10 with 0000:00:1c.4 PCI: Sharing IRQ 10 with 0000:05:00.0 PCI: Setting latency timer of device 0000:00:06.0 to 64 PCI: Found IRQ 10 for device 0000:00:1c.0 PCI: Sharing IRQ 10 with 0000:00:01.0 PCI: Sharing IRQ 10 with 0000:00:06.0 PCI: Sharing IRQ 10 with 0000:00:1a.0 PCI: Sharing IRQ 10 with 0000:00:1c.4 PCI: Sharing IRQ 10 with 0000:05:00.0 PCI: Setting latency timer of device 0000:00:1c.0 to 64 PCI: setting IRQ 15 as level-triggered PCI: Found IRQ 15 for device 0000:00:1c.3 PCI: Sharing IRQ 15 with 0000:00:1d.1 PCI: Sharing IRQ 15 with 0000:00:1f.2 PCI: Setting latency timer of device 0000:00:1c.3 to 64 PCI: Found IRQ 10 for device 0000:00:1c.4 PCI: Sharing IRQ 10 with 0000:00:01.0 PCI: Sharing IRQ 10 with 0000:00:06.0 PCI: Sharing IRQ 10 with 0000:00:1a.0 PCI: Sharing IRQ 10 with 0000:00:1c.0 PCI: Sharing IRQ 10 with 0000:05:00.0 PCI: Setting latency timer of device 0000:00:1c.4 to 64 PCI: setting IRQ 11 as level-triggered PCI: Found IRQ 11 for device 0000:00:1c.5 PCI: Sharing IRQ 11 with 0000:06:00.0 PCI: Setting latency timer of device 0000:00:1c.5 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered highmem bounce pool size: 64 pages SGI XFS with ACLs, no debug enabled io scheduler noop registered io scheduler cfq registered (default) pci 0000:01:00.0: Boot video device PCI: Setting latency timer of device 0000:00:01.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:01.0:pcie00] PCI: Setting latency timer of device 0000:00:06.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:06.0:pcie00] PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] PCI: Setting latency timer of device 0000:00:1c.3 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.3:pcie00] Allocate Port Service[0000:00:1c.3:pcie02] PCI: Setting latency timer of device 0000:00:1c.4 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.4:pcie00] Allocate Port Service[0000:00:1c.4:pcie02] PCI: Setting latency timer of device 0000:00:1c.5 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.5:pcie00] Allocate Port Service[0000:00:1c.5:pcie02] Driver 'sd' needs updating - please use bus_type methods ahci 0000:00:1f.2: version 3.0 PCI: Found IRQ 15 for device 0000:00:1f.2 PCI: Sharing IRQ 15 with 0000:00:1d.1 Switched to high resolution mode on CPU 0 ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pmp pio slum part PCI: Setting latency timer of device 0000:00:1f.2 to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci scsi4 : ahci scsi5 : ahci ata1: SATA max UDMA/133 abar m2048@0xe9406000 port 0xe9406100 irq 217 ata2: SATA max UDMA/133 abar m2048@0xe9406000 port 0xe9406180 irq 217 ata3: SATA max UDMA/133 abar m2048@0xe9406000 port 0xe9406200 irq 217 ata4: SATA max UDMA/133 abar m2048@0xe9406000 port 0xe9406280 irq 217 ata5: SATA max UDMA/133 abar m2048@0xe9406000 port 0xe9406300 irq 217 ata6: SATA max UDMA/133 abar m2048@0xe9406000 port 0xe9406380 irq 217 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-6: ST3500320NS, SN04, max UDMA/133 ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: ATA-6: ST3500320NS, SN04, max UDMA/133 ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata2.00: configured for UDMA/133 ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) ata5: SATA link down (SStatus 0 SControl 300) ata6: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA ST3500320NS SN04 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk scsi 1:0:0:0: Direct-Access ATA ST3500320NS SN04 PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sdb2 sdb3 sd 1:0:0:0: [sdb] Attached SCSI disk PCI: setting IRQ 5 as level-triggered PCI: Found IRQ 5 for device 0000:00:1a.7 PCI: Sharing IRQ 5 with 0000:00:1a.2 PCI: Sharing IRQ 5 with 0000:00:1d.2 PCI: Sharing IRQ 5 with 0000:00:1f.3 PCI: Sharing IRQ 5 with 0000:07:06.0 PCI: Setting latency timer of device 0000:00:1a.7 to 64 ehci_hcd 0000:00:1a.7: EHCI Host Controller ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 PCI: cache line size of 32 is not supported by device 0000:00:1a.7 ehci_hcd 0000:00:1a.7: irq 5, io mem 0xe9405000 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected PCI: setting IRQ 7 as level-triggered PCI: Found IRQ 7 for device 0000:00:1d.7 PCI: Sharing IRQ 7 with 0000:00:1d.0 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 7, io mem 0xe9404000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 6 ports detected USB Universal Host Controller Interface driver v3.0 PCI: Found IRQ 10 for device 0000:00:1a.0 PCI: Sharing IRQ 10 with 0000:05:00.0 PCI: Setting latency timer of device 0000:00:1a.0 to 64 uhci_hcd 0000:00:1a.0: UHCI Host Controller uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1a.0: irq 10, io base 0x0000e000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected PCI: setting IRQ 3 as level-triggered PCI: Found IRQ 3 for device 0000:00:1a.1 PCI: Setting latency timer of device 0000:00:1a.1 to 64 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1a.1: irq 3, io base 0x0000e100 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected PCI: Found IRQ 5 for device 0000:00:1a.2 PCI: Sharing IRQ 5 with 0000:00:1a.7 PCI: Sharing IRQ 5 with 0000:00:1d.2 PCI: Sharing IRQ 5 with 0000:00:1f.3 PCI: Sharing IRQ 5 with 0000:07:06.0 PCI: Setting latency timer of device 0000:00:1a.2 to 64 uhci_hcd 0000:00:1a.2: UHCI Host Controller uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1a.2: irq 5, io base 0x0000e200 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected PCI: Found IRQ 7 for device 0000:00:1d.0 PCI: Sharing IRQ 7 with 0000:00:1d.7 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 uhci_hcd 0000:00:1d.0: irq 7, io base 0x0000e300 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected PCI: Found IRQ 15 for device 0000:00:1d.1 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 uhci_hcd 0000:00:1d.1: irq 15, io base 0x0000e400 usb usb7: configuration #1 chosen from 1 choice hub 7-0:1.0: USB hub found hub 7-0:1.0: 2 ports detected PCI: Found IRQ 5 for device 0000:00:1d.2 PCI: Sharing IRQ 5 with 0000:00:1a.2 PCI: Sharing IRQ 5 with 0000:00:1a.7 PCI: Sharing IRQ 5 with 0000:00:1f.3 PCI: Sharing IRQ 5 with 0000:07:06.0 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 uhci_hcd 0000:00:1d.2: irq 5, io base 0x0000e500 usb usb8: configuration #1 chosen from 1 choice hub 8-0:1.0: USB hub found hub 8-0:1.0: 2 ports detected serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice md: raid1 personality registered for level 1 usb 8-2: new low speed USB device using uhci_hcd and address 2 usb 8-2: configuration #1 chosen from 1 choice input: Logitech Logitech USB Keyboard as /class/input/input0 input: USB HID v1.10 Keyboard [Logitech Logitech USB Keyboard] on usb-0000:00:1d.2-2 input: Logitech Logitech USB Keyboard as /class/input/input1 input: USB HID v1.10 Mouse [Logitech Logitech USB Keyboard] on usb-0000:00:1d.2-2 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode input: ImPS/2 Generic Wheel Mouse as /class/input/input2 md: Autodetecting RAID arrays. md: Scanned 6 and added 6 devices. md: autorun ... md: considering sdb3 ... md: adding sdb3 ... md: sdb2 has different UUID to sdb3 md: sdb1 has different UUID to sdb3 md: adding sda3 ... md: sda2 has different UUID to sdb3 md: sda1 has different UUID to sdb3 md: created md2 md: bind<sda3> md: bind<sdb3> md: running: <sdb3><sda3> raid1: raid set md2 active with 2 out of 2 mirrors md: considering sdb2 ... md: adding sdb2 ... md: sdb1 has different UUID to sdb2 md: adding sda2 ... md: sda1 has different UUID to sdb2 md: created md1 md: bind<sda2> md: bind<sdb2> md: running: <sdb2><sda2> raid1: raid set md1 active with 2 out of 2 mirrors md: considering sdb1 ... md: adding sdb1 ... md: adding sda1 ... md: created md0 md: bind<sda1> md: bind<sdb1> md: running: <sdb1><sda1> raid1: raid set md0 active with 2 out of 2 mirrors md: ... autorun DONE. Filesystem "md1": Disabling barriers, not supported by the underlying device XFS mounting filesystem md1 Ending clean XFS mount for filesystem: md1 VFS: Mounted root (xfs filesystem) readonly. Freeing unused kernel memory: 180k freed PCI: setting IRQ 14 as level-triggered PCI: Found IRQ 14 for device 0000:00:1b.0 PCI: Setting latency timer of device 0000:00:1b.0 to 64 hda_codec: Unknown model for ALC882, trying auto-probe from BIOS... r8169 Gigabit Ethernet driver 2.2LK loaded PCI: Found IRQ 10 for device 0000:05:00.0 PCI: Sharing IRQ 10 with 0000:00:1a.0 PCI: Setting latency timer of device 0000:05:00.0 to 64 eth0: RTL8168c/8111c at 0xf887a000, 00:1d:7d:06:7b:39, XID 3c2000c0 IRQ 216 Linux agpgart interface v0.103 nvidia: module license 'NVIDIA' taints kernel. r8169 Gigabit Ethernet driver 2.2LK loaded PCI: Found IRQ 11 for device 0000:06:00.0 PCI: Setting latency timer of device 0000:06:00.0 to 64 eth1: RTL8168c/8111c at 0xf887c000, 00:1d:7d:06:75:d8, XID 3c2000c0 IRQ 215 PCI: Setting latency timer of device 0000:01:00.0 to 64 NVRM: loading NVIDIA UNIX x86 Kernel Module 169.12 Thu Feb 14 17:53:07 PST 2008 Filesystem "md1": Disabling barriers, not supported by the underlying device r8169: eth1: link down r8169: eth0: link up r8169: eth1: link down r8169: eth0: link up r8169: eth1: link up r8169: eth1: link up Filesystem "md0": Disabling barriers, not supported by the underlying device XFS mounting filesystem md0 Ending clean XFS mount for filesystem: md0 quadstation ~ # cat /proc/cmdline root=/dev/md1 noapic 00:00.0 0600: 8086:29e0 (rev 01) Subsystem: 1458:5000 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information <?> 00: 86 80 e0 29 06 00 90 20 01 00 00 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 58 14 00 50 30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 00:01.0 0604: 8086:29e1 (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: e4000000-e6ffffff Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [88] Subsystem: 1458:5000 Capabilities: [80] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0 +,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0100c Data: 4139 Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #2, Speed 5GT/s, Width x16, ASPM L0s, Latency L0 <512ns, L1 <64us ClockPM- Suprise- LLActRep- BwNot+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise- Slot # 20, PowerLimit 75.000000; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet + Interlock- Changed: MRL- PresDet+ LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Kernel driver in use: pcieport-driver 00: 86 80 e1 29 07 04 10 00 01 00 04 06 08 00 01 00 10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 00 00 20: 00 e4 f0 e6 01 d0 f1 df 00 00 00 00 00 00 00 00 30: 00 00 00 00 88 00 00 00 00 00 00 00 0a 01 08 00 00:06.0 0604: 8086:29e9 (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 00009000-00009fff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [88] Subsystem: 1458:5000 Capabilities: [80] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0 +,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0100c Data: 4141 Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #3, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <1us, L1 <4us ClockPM- Suprise- LLActRep- BwNot+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise- Slot # 0, PowerLimit 0.000000; Interlock- NoCompl+ SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Kernel driver in use: pcieport-driver 00: 86 80 e9 29 07 04 10 00 01 00 04 06 08 00 01 00 10: 00 00 00 00 00 00 00 00 00 02 02 00 90 90 00 00 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 88 00 00 00 00 00 00 00 0a 01 00 00 00:1a.0 0c03: 8086:2937 (rev 02) (prog-if 00 [UHCI]) Subsystem: 1458:5004 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 10 Region 4: I/O ports at e000 [size=32] Capabilities: [50] PCIe advanced features <?> Kernel driver in use: uhci_hcd 00: 86 80 37 29 05 00 90 02 02 00 03 0c 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 e0 00 00 00 00 00 00 00 00 00 00 58 14 04 50 30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00 00:1a.1 0c03: 8086:2938 (rev 02) (prog-if 00 [UHCI]) Subsystem: 1458:5004 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 3 Region 4: I/O ports at e100 [size=32] Capabilities: [50] PCIe advanced features <?> Kernel driver in use: uhci_hcd 00: 86 80 38 29 05 00 90 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 e1 00 00 00 00 00 00 00 00 00 00 58 14 04 50 30: 00 00 00 00 50 00 00 00 00 00 00 00 03 02 00 00 00:1a.2 0c03: 8086:2939 (rev 02) (prog-if 00 [UHCI]) Subsystem: 1458:5004 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 5 Region 4: I/O ports at e200 [size=32] Capabilities: [50] PCIe advanced features <?> Kernel driver in use: uhci_hcd 00: 86 80 39 29 05 00 90 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 e2 00 00 00 00 00 00 00 00 00 00 58 14 04 50 30: 00 00 00 00 50 00 00 00 00 00 00 00 05 03 00 00 00:1a.7 0c03: 8086:293c (rev 02) (prog-if 20 [EHCI]) Subsystem: 1458:5006 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 5 Region 0: Memory at e9405000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ehci_hcd 00: 86 80 3c 29 06 00 90 02 02 20 03 0c 00 00 00 00 10: 00 50 40 e9 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 58 14 06 50 30: 00 00 00 00 50 00 00 00 00 00 00 00 05 03 00 00 00:1b.0 0403: 8086:293e (rev 02) Subsystem: 1458:a022 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 14 Region 0: Memory at e9400000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0 +,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE- FLReset+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00: 86 80 3e 29 06 00 10 00 02 00 03 04 08 00 00 00 10: 04 00 40 e9 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 58 14 22 a0 30: 00 00 00 00 50 00 00 00 00 00 00 00 0e 01 00 00 00:1c.0 0604: 8086:2940 (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000a000-0000afff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <1us, L1 <4us ClockPM- Suprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+ Slot # 10, PowerLimit 10.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0100c Data: 4149 Capabilities: [90] Subsystem: 1458:5001 Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0 +,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport-driver 00: 86 80 40 29 07 04 10 00 02 00 04 06 08 00 81 00 10: 00 00 00 00 00 00 00 00 00 03 03 00 a0 a0 00 00 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 00 00 00:1c.3 0604: 8086:2946 (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: e9100000-e91fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <256ns, L1 <4us ClockPM- Suprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+ Slot # 13, PowerLimit 10.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet + Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0100c Data: 4151 Capabilities: [90] Subsystem: 1458:5001 Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0 +,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport-driver 00: 86 80 46 29 07 04 10 00 02 00 04 06 08 00 81 00 10: 00 00 00 00 00 00 00 00 00 04 04 00 b0 b0 00 00 20: 10 e9 10 e9 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 0f 04 00 00 00:1c.4 0604: 8086:2948 (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: e7000000-e7ffffff Prefetchable memory behind bridge: 00000000e9000000-00000000e90fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <256ns, L1 <4us ClockPM- Suprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+ Slot # 14, PowerLimit 10.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet + Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0100c Data: 4159 Capabilities: [90] Subsystem: 1458:5001 Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0 +,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport-driver 00: 86 80 48 29 07 04 10 00 02 00 04 06 08 00 81 00 10: 00 00 00 00 00 00 00 00 00 05 05 00 c0 c0 00 20 20: 00 e7 f0 e7 01 e9 01 e9 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 00 00 00:1c.5 0604: 8086:294a (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: e8000000-e8ffffff Prefetchable memory behind bridge: 00000000e9200000-00000000e92fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #6, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <256ns, L1 <4us ClockPM- Suprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+ Slot # 15, PowerLimit 10.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet + Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0100c Data: 4161 Capabilities: [90] Subsystem: 1458:5001 Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0 +,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pcieport-driver 00: 86 80 4a 29 07 04 10 00 02 00 04 06 08 00 81 00 10: 00 00 00 00 00 00 00 00 00 06 06 00 d0 d0 00 00 20: 00 e8 f0 e8 21 e9 21 e9 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 02 00 00 00:1d.0 0c03: 8086:2934 (rev 02) (prog-if 00 [UHCI]) Subsystem: 1458:5004 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 7 Region 4: I/O ports at e300 [size=32] Capabilities: [50] PCIe advanced features <?> Kernel driver in use: uhci_hcd 00: 86 80 34 29 05 00 90 02 02 00 03 0c 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 e3 00 00 00 00 00 00 00 00 00 00 58 14 04 50 30: 00 00 00 00 50 00 00 00 00 00 00 00 07 01 00 00 00:1d.1 0c03: 8086:2935 (rev 02) (prog-if 00 [UHCI]) Subsystem: 1458:5004 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 15 Region 4: I/O ports at e400 [size=32] Capabilities: [50] PCIe advanced features <?> Kernel driver in use: uhci_hcd 00: 86 80 35 29 05 00 90 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 e4 00 00 00 00 00 00 00 00 00 00 58 14 04 50 30: 00 00 00 00 50 00 00 00 00 00 00 00 0f 02 00 00 00:1d.2 0c03: 8086:2936 (rev 02) (prog-if 00 [UHCI]) Subsystem: 1458:5004 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 5 Region 4: I/O ports at e500 [size=32] Capabilities: [50] PCIe advanced features <?> Kernel driver in use: uhci_hcd 00: 86 80 36 29 05 00 90 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 e5 00 00 00 00 00 00 00 00 00 00 58 14 04 50 30: 00 00 00 00 50 00 00 00 00 00 00 00 05 03 00 00 00:1d.7 0c03: 8086:293a (rev 02) (prog-if 20 [EHCI]) Subsystem: 1458:5006 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 7 Region 0: Memory at e9404000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ehci_hcd 00: 86 80 3a 29 06 00 90 02 02 20 03 0c 00 00 00 00 10: 00 40 40 e9 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 58 14 06 50 30: 00 00 00 00 50 00 00 00 00 00 00 00 07 01 00 00 00:1e.0 0604: 8086:244e (rev 92) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=32 Memory behind bridge: e9300000-e93fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Subsystem: 1458:5000 00: 86 80 4e 24 07 00 10 00 92 01 04 06 00 00 01 00 10: 00 00 00 00 00 00 00 00 00 07 07 20 f0 00 80 22 20: 30 e9 30 e9 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 00 00 00:1f.0 0601: 8086:2916 (rev 02) Subsystem: 1458:5001 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information <?> 00: 86 80 16 29 07 01 10 02 02 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 58 14 01 50 30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 00:1f.2 0106: 8086:2922 (rev 02) (prog-if 01 [AHCI 1.0]) Subsystem: 1458:b005 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 217 Region 0: I/O ports at e600 [size=8] Region 1: I/O ports at e700 [size=4] Region 2: I/O ports at e800 [size=8] Region 3: I/O ports at e900 [size=4] Region 4: I/O ports at ea00 [size=32] Region 5: Memory at e9406000 (32-bit, non-prefetchable) [size=2K] Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/4 Enable+ Address: fee0100c Data: 4169 Capabilities: [70] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a8] SATA HBA <?> Capabilities: [b0] PCIe advanced features <?> Kernel driver in use: ahci 00: 86 80 22 29 07 04 b0 02 02 01 06 01 00 00 00 00 10: 01 e6 00 00 01 e7 00 00 01 e8 00 00 01 e9 00 00 20: 01 ea 00 00 00 60 40 e9 00 00 00 00 58 14 05 b0 30: 00 00 00 00 80 00 00 00 00 00 00 00 0f 02 00 00 00:1f.3 0c05: 8086:2930 (rev 02) Subsystem: 1458:5001 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 5 Region 0: Memory at e9407000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at 0500 [size=32] 00: 86 80 30 29 03 00 80 02 02 00 05 0c 00 00 00 00 10: 04 70 40 e9 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 05 00 00 00 00 00 00 00 00 00 00 58 14 01 50 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 03 00 00 01:00.0 0300: 10de:00f8 (rev a2) (prog-if 00 [VGA controller]) Subsystem: 10de:01ff Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 10 Region 0: Memory at e4000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at d0000000 (32-bit, prefetchable) [size=256M] Region 2: Memory at e5000000 (32-bit, non-prefetchable) [size=16M] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [78] Express (v1) Legacy Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s, Latency L0 <2us, L1 <16us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Kernel driver in use: nvidia Kernel modules: nvidia 00: de 10 f8 00 07 00 10 00 a2 00 00 03 08 00 00 00 10: 00 00 00 e4 08 00 00 d0 00 00 00 e5 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 de 10 ff 01 30: 00 00 00 00 60 00 00 00 00 00 00 00 0a 01 00 00 05:00.0 0200: 10ec:8168 (rev ff) (prog-if ff) !!! Unknown header type 7f Kernel driver in use: r8169 Kernel modules: r8169 00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 06:00.0 0200: 10ec:8168 (rev 02) Subsystem: 1458:e000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 215 Region 0: I/O ports at d000 [size=256] Region 2: Memory at e9210000 (64-bit, prefetchable) [size=4K] Region 4: Memory at e9200000 (64-bit, prefetchable) [size=64K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1 +,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+ Address: 00000000fee0100c Data: 4179 Capabilities: [70] Express (v1) Endpoint, MSI 01 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <8us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us ClockPM+ Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [b0] MSI-X: Enable- Mask- TabSize=2 Vector table: BAR=4 offset=00000000 PBA: BAR=4 offset=00000800 Capabilities: [d0] Vital Product Data <?> Kernel driver in use: r8169 Kernel modules: r8169 00: ec 10 68 81 07 04 10 00 02 00 00 02 08 00 00 00 10: 01 d0 00 00 00 00 00 00 0c 00 21 e9 00 00 00 00 20: 0c 00 20 e9 00 00 00 00 00 00 00 00 58 14 00 e0 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00 07:06.0 0c00: 104c:8024 (prog-if 10 [OHCI]) Subsystem: 1458:1000 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (500ns min, 1000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 5 Region 0: Memory at e9304000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at e9300000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1 +,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 4c 10 24 80 06 00 10 02 00 10 00 0c 08 20 00 00 10: 00 40 30 e9 00 00 30 e9 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 58 14 00 10 30: 00 00 00 00 44 00 00 00 00 00 00 00 05 01 02 04 quadstation ~ # cat /proc/interrupts CPU0 0: 273 XT-PIC-XT timer 1: 2 XT-PIC-XT i8042 2: 0 XT-PIC-XT cascade 3: 0 XT-PIC-XT uhci_hcd:usb4 5: 680 XT-PIC-XT ehci_hcd:usb1, uhci_hcd:usb5, uhci_hcd:usb8 7: 2 XT-PIC-XT ehci_hcd:usb2, uhci_hcd:usb6 10: 0 XT-PIC-XT uhci_hcd:usb3 12: 114 XT-PIC-XT i8042 14: 185 XT-PIC-XT HDA Intel 15: 0 XT-PIC-XT uhci_hcd:usb7 215: 662 PCI-MSI-edge eth1 217: 2453 PCI-MSI-edge ahci NMI: 0 Non-maskable interrupts LOC: 557133 Local timer interrupts TRM: 0 Thermal event interrupts SPU: 0 Spurious interrupts ERR: 0 MIS: 0 Yes, the kernel is tainted (for some reason gentoo/udev autoloads it..), but not to worry, i have tested without it (before i even got it), and its the exact same result, however, if you do not believe that, i shall happily delete the module in question, and repost. anything else you need? > > > > -- > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Realtek 8111c weirdness problems, apic/msi, and normal bug 2008-04-10 12:17 ` Kasper Sandberg @ 2008-04-11 1:11 ` Kasper Sandberg 2008-04-11 18:06 ` Kasper Sandberg 2008-04-12 19:22 ` Francois Romieu 0 siblings, 2 replies; 9+ messages in thread From: Kasper Sandberg @ 2008-04-11 1:11 UTC (permalink / raw) To: Francois Romieu; +Cc: Andrew Morton, LKML Mailinglist, linux-acpi, netdev [-- Attachment #1: Type: text/plain, Size: 2453 bytes --] Sorry for top posting, but its just easier in this case :) I may have just gotten some new information to share. I just built -git8. and the nic didnt work.. by booting with noapic/nomsi i got it running though. then i did some tests, and rebooted into the default(has worked mostly for me) noapic/msi boot. Then it worked. i did get some interresting information though, which i think may help to fix the problem.. if its a boot where the nic works, i can usually rmmod/modprobe the module once without it giving error, however if its a boot where the nic doesent work, first time i rmmod and modprobe, it gives me an error.. the error is: PCI: cache line size of 32 is not supported by device 0000:05:00.0 ACPI: PCI interrupt for device 0000:05:00.0 disabled r8169: probe of 0000:05:00.0 failed with error -22 I have attached some dmesgs(sorry, but my client messes up inlines..) also.. link detecting isnt working properly, sometimes it will detect a link as down after a while.. its quite weird.. (oh, and this time its without nvidia just to be 100000% sure) I hope this can help to get it resolved, alot of people are having problems with these controllers.. i can however confirm that a similar controller is working perfectly on a friends gigabyte motherboard, thats with P35 chipset though, i have X48. He has only 1 of them onboard. also something which may be of interrest, realtek offers a modified r8169 driver called "r8168", which supposedly fixes this. I have been unable to get it to compile though, but i saw it on ubuntu forums. On Thu, 2008-04-10 at 14:17 +0200, Kasper Sandberg wrote: > On Mon, 2008-04-07 at 06:09 +0200, Kasper Sandberg wrote: > > Hello. > > > > I apologize, but it will have to wait a few days, as the fan on the > > graphics card just broke, and it overheats almost instantly. > > > > I will post as soon as possible, sorry for the inconvenience. <snip> > > > > > > > > > > -- > > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > > the body of a message to majordomo@vger.kernel.org > > More majordomo info at http://vger.kernel.org/majordomo-info.html > > Please read the FAQ at http://www.tux.org/lkml/ > > -- > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > Please read the FAQ at http://www.tux.org/lkml/ [-- Attachment #2: noapicmsi_workssemi --] [-- Type: text/plain, Size: 15403 bytes --] und 12 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report system 00:01: ioport range 0x4d0-0x4d1 has been reserved system 00:01: ioport range 0x290-0x29f has been reserved system 00:01: ioport range 0x800-0x87f has been reserved system 00:01: ioport range 0x290-0x294 has been reserved system 00:01: ioport range 0x880-0x88f has been reserved system 00:08: ioport range 0x400-0x4bf could not be reserved system 00:09: iomem range 0xe0000000-0xe3ffffff could not be reserved system 00:0a: iomem range 0xd1e00-0xd3fff has been reserved system 00:0a: iomem range 0xf0000-0xf7fff could not be reserved system 00:0a: iomem range 0xf8000-0xfbfff could not be reserved system 00:0a: iomem range 0xfc000-0xfffff could not be reserved system 00:0a: iomem range 0xcfee0000-0xcfefffff could not be reserved system 00:0a: iomem range 0x0-0x9ffff could not be reserved system 00:0a: iomem range 0x100000-0xcfedffff could not be reserved system 00:0a: iomem range 0xfec00000-0xfec00fff could not be reserved system 00:0a: iomem range 0xfed10000-0xfed1dfff could not be reserved system 00:0a: iomem range 0xfed20000-0xfed8ffff could not be reserved system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved system 00:0a: iomem range 0xffb00000-0xffb7ffff could not be reserved system 00:0a: iomem range 0xfff00000-0xffffffff could not be reserved system 00:0a: iomem range 0xe0000-0xeffff has been reserved PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: 0xe4000000-0xe6ffffff PREFETCH window: 0x00000000d0000000-0x00000000dfffffff PCI: Bridge: 0000:00:06.0 IO window: 9000-9fff MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.0 IO window: a000-afff MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.3 IO window: b000-bfff MEM window: 0xe9100000-0xe91fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.4 IO window: c000-cfff MEM window: 0xe7000000-0xe7ffffff PREFETCH window: 0x00000000e9000000-0x00000000e90fffff PCI: Bridge: 0000:00:1c.5 IO window: d000-dfff MEM window: 0xe8000000-0xe8ffffff PREFETCH window: 0x00000000e9200000-0x00000000e92fffff PCI: Bridge: 0000:00:1e.0 IO window: disabled. MEM window: 0xe9300000-0xe93fffff PREFETCH window: disabled. ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:01.0 to 64 ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:06.0 to 64 ACPI: PCI Interrupt 0000:00:1c.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1c.0 to 64 ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 15 PCI: setting IRQ 15 as level-triggered ACPI: PCI Interrupt 0000:00:1c.3[D] -> Link [LNKD] -> GSI 15 (level, low) -> IRQ 15 PCI: Setting latency timer of device 0000:00:1c.3 to 64 ACPI: PCI Interrupt 0000:00:1c.4[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1c.4 to 64 ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:1c.5[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1c.5 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered highmem bounce pool size: 64 pages SGI XFS with ACLs, no debug enabled io scheduler noop registered io scheduler cfq registered (default) pci 0000:01:00.0: Boot video device PCI: Setting latency timer of device 0000:00:01.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:01.0:pcie00] Allocate Port Service[0000:00:01.0:pcie03] PCI: Setting latency timer of device 0000:00:06.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:06.0:pcie00] Allocate Port Service[0000:00:06.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] Allocate Port Service[0000:00:1c.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.3 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.3:pcie00] Allocate Port Service[0000:00:1c.3:pcie02] Allocate Port Service[0000:00:1c.3:pcie03] PCI: Setting latency timer of device 0000:00:1c.4 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.4:pcie00] Allocate Port Service[0000:00:1c.4:pcie02] Allocate Port Service[0000:00:1c.4:pcie03] PCI: Setting latency timer of device 0000:00:1c.5 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.5:pcie00] Allocate Port Service[0000:00:1c.5:pcie02] Allocate Port Service[0000:00:1c.5:pcie03] Driver 'sd' needs updating - please use bus_type methods ahci 0000:00:1f.2: version 3.0 ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> GSI 15 (level, low) -> IRQ 15 Switched to high resolution mode on CPU 0 ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pmp pio slum part PCI: Setting latency timer of device 0000:00:1f.2 to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci scsi4 : ahci scsi5 : ahci ata1: SATA max UDMA/133 abar m2048@0xe9406000 port 0xe9406100 irq 217 ata2: SATA max UDMA/133 abar m2048@0xe9406000 port 0xe9406180 irq 217 ata3: SATA max UDMA/133 abar m2048@0xe9406000 port 0xe9406200 irq 217 ata4: SATA max UDMA/133 abar m2048@0xe9406000 port 0xe9406280 irq 217 ata5: SATA max UDMA/133 abar m2048@0xe9406000 port 0xe9406300 irq 217 ata6: SATA max UDMA/133 abar m2048@0xe9406000 port 0xe9406380 irq 217 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-6: ST3500320NS, SN04, max UDMA/133 ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: ATA-6: ST3500320NS, SN04, max UDMA/133 ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata2.00: configured for UDMA/133 ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) ata5: SATA link down (SStatus 0 SControl 300) ata6: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA ST3500320NS SN04 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk scsi 1:0:0:0: Direct-Access ATA ST3500320NS SN04 PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sdb2 sdb3 sd 1:0:0:0: [sdb] Attached SCSI disk ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:00:1a.7[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:1a.7 to 64 ehci_hcd 0000:00:1a.7: EHCI Host Controller ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 PCI: cache line size of 32 is not supported by device 0000:00:1a.7 ehci_hcd 0000:00:1a.7: irq 5, io mem 0xe9405000 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 7 PCI: setting IRQ 7 as level-triggered ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNK1] -> GSI 7 (level, low) -> IRQ 7 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 7, io mem 0xe9404000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 6 ports detected USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1a.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1a.0 to 64 uhci_hcd 0000:00:1a.0: UHCI Host Controller uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1a.0: irq 10, io base 0x0000e000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 3 PCI: setting IRQ 3 as level-triggered ACPI: PCI Interrupt 0000:00:1a.1[B] -> Link [LNKF] -> GSI 3 (level, low) -> IRQ 3 PCI: Setting latency timer of device 0000:00:1a.1 to 64 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1a.1: irq 3, io base 0x0000e100 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1a.2[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:1a.2 to 64 uhci_hcd 0000:00:1a.2: UHCI Host Controller uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1a.2: irq 5, io base 0x0000e200 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNK1] -> GSI 7 (level, low) -> IRQ 7 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 uhci_hcd 0000:00:1d.0: irq 7, io base 0x0000e300 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 15 (level, low) -> IRQ 15 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 uhci_hcd 0000:00:1d.1: irq 15, io base 0x0000e400 usb usb7: configuration #1 chosen from 1 choice hub 7-0:1.0: USB hub found hub 7-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 uhci_hcd 0000:00:1d.2: irq 5, io base 0x0000e500 usb usb8: configuration #1 chosen from 1 choice hub 8-0:1.0: USB hub found hub 8-0:1.0: 2 ports detected PNP: PS/2 Controller [PNP0f13:PS2M] at 0x60,0x64 irq 12 PNP: PS/2 controller doesn't have KBD irq; using default 1 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice md: raid1 personality registered for level 1 cpuidle: using governor ladder usb 8-2: new low speed USB device using uhci_hcd and address 2 usb 8-2: configuration #1 chosen from 1 choice input: Logitech Logitech USB Keyboard as /class/input/input0 input: USB HID v1.10 Keyboard [Logitech Logitech USB Keyboard] on usb-0000:00:1d.2-2 input: Logitech Logitech USB Keyboard as /class/input/input1 input: USB HID v1.10 Mouse [Logitech Logitech USB Keyboard] on usb-0000:00:1d.2-2 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode input: ImPS/2 Generic Wheel Mouse as /class/input/input2 md: Autodetecting RAID arrays. md: Scanned 6 and added 6 devices. md: autorun ... md: considering sdb3 ... md: adding sdb3 ... md: sdb2 has different UUID to sdb3 md: sdb1 has different UUID to sdb3 md: adding sda3 ... md: sda2 has different UUID to sdb3 md: sda1 has different UUID to sdb3 md: created md2 md: bind<sda3> md: bind<sdb3> md: running: <sdb3><sda3> raid1: raid set md2 active with 2 out of 2 mirrors md: considering sdb2 ... md: adding sdb2 ... md: sdb1 has different UUID to sdb2 md: adding sda2 ... md: sda1 has different UUID to sdb2 md: created md1 md: bind<sda2> md: bind<sdb2> md: running: <sdb2><sda2> raid1: raid set md1 active with 2 out of 2 mirrors md: considering sdb1 ... md: adding sdb1 ... md: adding sda1 ... md: created md0 md: bind<sda1> md: bind<sdb1> md: running: <sdb1><sda1> raid1: raid set md0 active with 2 out of 2 mirrors md: ... autorun DONE. Filesystem "md1": Disabling barriers, not supported by the underlying device XFS mounting filesystem md1 Ending clean XFS mount for filesystem: md1 VFS: Mounted root (xfs filesystem) readonly. Freeing unused kernel memory: 204k freed ACPI: ACPI0007:00 is registered as cooling_device0 ACPI: Processor [CPU0] (supports 8 throttling states) input: Power Button (FF) as /class/input/input3 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input4 ACPI: Power Button (CM) [PWRB] ACPI: PCI Interrupt Link [LNK0] enabled at IRQ 14 PCI: setting IRQ 14 as level-triggered ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNK0] -> GSI 14 (level, low) -> IRQ 14 PCI: Setting latency timer of device 0000:00:1b.0 to 64 hda_codec: Unknown model for ALC882, trying auto-probe from BIOS... r8169 Gigabit Ethernet driver 2.2LK loaded ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:05:00.0 to 64 eth0: RTL8168c/8111c at 0xf8878000, 00:1d:7d:06:7b:39, XID 3c2000c0 IRQ 216 r8169 Gigabit Ethernet driver 2.2LK loaded ACPI: PCI Interrupt 0000:06:00.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:06:00.0 to 64 eth1: RTL8168c/8111c at 0xf88a6000, 00:1d:7d:06:75:d8, XID 3c2000c0 IRQ 215 Filesystem "md1": Disabling barriers, not supported by the underlying device r8169: eth1: link up r8169: eth1: link up r8169: eth1: link up r8169: eth0: link up r8169: eth0: link up [-- Attachment #3: noapicnomsi_only1enabled_broken_error --] [-- Type: text/plain, Size: 15409 bytes --] rrupt Link [LNK1] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 12 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report system 00:01: ioport range 0x4d0-0x4d1 has been reserved system 00:01: ioport range 0x290-0x29f has been reserved system 00:01: ioport range 0x800-0x87f has been reserved system 00:01: ioport range 0x290-0x294 has been reserved system 00:01: ioport range 0x880-0x88f has been reserved system 00:08: ioport range 0x400-0x4bf could not be reserved system 00:09: iomem range 0xe0000000-0xe3ffffff could not be reserved system 00:0a: iomem range 0xd1e00-0xd3fff has been reserved system 00:0a: iomem range 0xf0000-0xf7fff could not be reserved system 00:0a: iomem range 0xf8000-0xfbfff could not be reserved system 00:0a: iomem range 0xfc000-0xfffff could not be reserved system 00:0a: iomem range 0xcfee0000-0xcfefffff could not be reserved system 00:0a: iomem range 0x0-0x9ffff could not be reserved system 00:0a: iomem range 0x100000-0xcfedffff could not be reserved system 00:0a: iomem range 0xfec00000-0xfec00fff could not be reserved system 00:0a: iomem range 0xfed10000-0xfed1dfff could not be reserved system 00:0a: iomem range 0xfed20000-0xfed8ffff could not be reserved system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved system 00:0a: iomem range 0xffb00000-0xffb7ffff could not be reserved system 00:0a: iomem range 0xfff00000-0xffffffff could not be reserved system 00:0a: iomem range 0xe0000-0xeffff has been reserved PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: 0xe4000000-0xe6ffffff PREFETCH window: 0x00000000d0000000-0x00000000dfffffff PCI: Bridge: 0000:00:06.0 IO window: a000-afff MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.0 IO window: c000-cfff MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.3 IO window: b000-bfff MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.4 IO window: d000-dfff MEM window: 0xe7000000-0xe7ffffff PREFETCH window: 0x00000000e8000000-0x00000000e80fffff PCI: Bridge: 0000:00:1e.0 IO window: disabled. MEM window: 0xe8100000-0xe81fffff PREFETCH window: disabled. ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:01.0 to 64 ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:06.0 to 64 ACPI: PCI Interrupt 0000:00:1c.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1c.0 to 64 ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 15 PCI: setting IRQ 15 as level-triggered ACPI: PCI Interrupt 0000:00:1c.3[D] -> Link [LNKD] -> GSI 15 (level, low) -> IRQ 15 PCI: Setting latency timer of device 0000:00:1c.3 to 64 ACPI: PCI Interrupt 0000:00:1c.4[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1c.4 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered highmem bounce pool size: 64 pages SGI XFS with ACLs, no debug enabled io scheduler noop registered io scheduler cfq registered (default) pci 0000:01:00.0: Boot video device PCI: Setting latency timer of device 0000:00:01.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:01.0:pcie00] Allocate Port Service[0000:00:01.0:pcie03] PCI: Setting latency timer of device 0000:00:06.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:06.0:pcie00] Allocate Port Service[0000:00:06.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] Allocate Port Service[0000:00:1c.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.3 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.3:pcie00] Allocate Port Service[0000:00:1c.3:pcie02] Allocate Port Service[0000:00:1c.3:pcie03] PCI: Setting latency timer of device 0000:00:1c.4 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.4:pcie00] Allocate Port Service[0000:00:1c.4:pcie02] Allocate Port Service[0000:00:1c.4:pcie03] Driver 'sd' needs updating - please use bus_type methods ahci 0000:00:1f.2: version 3.0 ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> GSI 15 (level, low) -> IRQ 15 Switched to high resolution mode on CPU 0 ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pmp pio slum part PCI: Setting latency timer of device 0000:00:1f.2 to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci scsi4 : ahci scsi5 : ahci ata1: SATA max UDMA/133 abar m2048@0xe8206000 port 0xe8206100 irq 15 ata2: SATA max UDMA/133 abar m2048@0xe8206000 port 0xe8206180 irq 15 ata3: SATA max UDMA/133 abar m2048@0xe8206000 port 0xe8206200 irq 15 ata4: SATA max UDMA/133 abar m2048@0xe8206000 port 0xe8206280 irq 15 ata5: SATA max UDMA/133 abar m2048@0xe8206000 port 0xe8206300 irq 15 ata6: SATA max UDMA/133 abar m2048@0xe8206000 port 0xe8206380 irq 15 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-6: ST3500320NS, SN04, max UDMA/133 ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: ATA-6: ST3500320NS, SN04, max UDMA/133 ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata2.00: configured for UDMA/133 ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) ata5: SATA link down (SStatus 0 SControl 300) ata6: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA ST3500320NS SN04 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk scsi 1:0:0:0: Direct-Access ATA ST3500320NS SN04 PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sdb2 sdb3 sd 1:0:0:0: [sdb] Attached SCSI disk ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 14 PCI: setting IRQ 14 as level-triggered ACPI: PCI Interrupt 0000:00:1a.7[C] -> Link [LNKC] -> GSI 14 (level, low) -> IRQ 14 PCI: Setting latency timer of device 0000:00:1a.7 to 64 ehci_hcd 0000:00:1a.7: EHCI Host Controller ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 PCI: cache line size of 32 is not supported by device 0000:00:1a.7 ehci_hcd 0000:00:1a.7: irq 14, io mem 0xe8205000 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNK1] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 5, io mem 0xe8204000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 6 ports detected USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1a.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1a.0 to 64 uhci_hcd 0000:00:1a.0: UHCI Host Controller uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1a.0: irq 11, io base 0x0000e200 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 7 PCI: setting IRQ 7 as level-triggered ACPI: PCI Interrupt 0000:00:1a.1[B] -> Link [LNKF] -> GSI 7 (level, low) -> IRQ 7 PCI: Setting latency timer of device 0000:00:1a.1 to 64 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1a.1: irq 7, io base 0x0000e000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1a.2[C] -> Link [LNKC] -> GSI 14 (level, low) -> IRQ 14 PCI: Setting latency timer of device 0000:00:1a.2 to 64 uhci_hcd 0000:00:1a.2: UHCI Host Controller uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1a.2: irq 14, io base 0x0000e100 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNK1] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 uhci_hcd 0000:00:1d.0: irq 5, io base 0x0000e300 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 15 (level, low) -> IRQ 15 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 uhci_hcd 0000:00:1d.1: irq 15, io base 0x0000e400 usb usb7: configuration #1 chosen from 1 choice hub 7-0:1.0: USB hub found hub 7-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 14 (level, low) -> IRQ 14 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 uhci_hcd 0000:00:1d.2: irq 14, io base 0x0000e500 usb usb8: configuration #1 chosen from 1 choice hub 8-0:1.0: USB hub found hub 8-0:1.0: 2 ports detected PNP: PS/2 Controller [PNP0f13:PS2M] at 0x60,0x64 irq 12 PNP: PS/2 controller doesn't have KBD irq; using default 1 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice md: raid1 personality registered for level 1 cpuidle: using governor ladder usb 8-2: new low speed USB device using uhci_hcd and address 2 usb 8-2: configuration #1 chosen from 1 choice input: Logitech Logitech USB Keyboard as /class/input/input0 input: USB HID v1.10 Keyboard [Logitech Logitech USB Keyboard] on usb-0000:00:1d.2-2 input: Logitech Logitech USB Keyboard as /class/input/input1 input: USB HID v1.10 Mouse [Logitech Logitech USB Keyboard] on usb-0000:00:1d.2-2 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode input: ImPS/2 Generic Wheel Mouse as /class/input/input2 md: Autodetecting RAID arrays. md: Scanned 6 and added 6 devices. md: autorun ... md: considering sdb3 ... md: adding sdb3 ... md: sdb2 has different UUID to sdb3 md: sdb1 has different UUID to sdb3 md: adding sda3 ... md: sda2 has different UUID to sdb3 md: sda1 has different UUID to sdb3 md: created md2 md: bind<sda3> md: bind<sdb3> md: running: <sdb3><sda3> raid1: raid set md2 active with 2 out of 2 mirrors md: considering sdb2 ... md: adding sdb2 ... md: sdb1 has different UUID to sdb2 md: adding sda2 ... md: sda1 has different UUID to sdb2 md: created md1 md: bind<sda2> md: bind<sdb2> md: running: <sdb2><sda2> raid1: raid set md1 active with 2 out of 2 mirrors md: considering sdb1 ... md: adding sdb1 ... md: adding sda1 ... md: created md0 md: bind<sda1> md: bind<sdb1> md: running: <sdb1><sda1> raid1: raid set md0 active with 2 out of 2 mirrors md: ... autorun DONE. Filesystem "md1": Disabling barriers, not supported by the underlying device XFS mounting filesystem md1 Ending clean XFS mount for filesystem: md1 VFS: Mounted root (xfs filesystem) readonly. Freeing unused kernel memory: 204k freed ACPI: ACPI0007:00 is registered as cooling_device0 ACPI: Processor [CPU0] (supports 8 throttling states) input: Power Button (FF) as /class/input/input3 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input4 ACPI: Power Button (CM) [PWRB] r8169 Gigabit Ethernet driver 2.2LK loaded ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:05:00.0 to 64 r8169 0000:05:00.0: no MSI. Back to INTx. eth0: RTL8168c/8111c at 0xf8864000, 00:1d:7d:06:7b:39, XID 3c2000c0 IRQ 11 ACPI: PCI Interrupt Link [LNK0] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNK0] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1b.0 to 64 hda_codec: Unknown model for ALC882, trying auto-probe from BIOS... Filesystem "md1": Disabling barriers, not supported by the underlying device r8169: eth0: link up r8169: eth0: link up ACPI: PCI interrupt for device 0000:05:00.0 disabled r8169 Gigabit Ethernet driver 2.2LK loaded ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:05:00.0 to 64 r8169 0000:05:00.0: no MSI. Back to INTx. eth0: RTL8168c/8111c at 0xf8864000, 00:1d:7d:06:7b:39, XID 3c2000c0 IRQ 11 r8169: eth0: link up ACPI: PCI interrupt for device 0000:05:00.0 disabled r8169 Gigabit Ethernet driver 2.2LK loaded ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: cache line size of 32 is not supported by device 0000:05:00.0 ACPI: PCI interrupt for device 0000:05:00.0 disabled r8169: probe of 0000:05:00.0 failed with error -22 [-- Attachment #4: noapicnomsi_only1enabled_works --] [-- Type: text/plain, Size: 15415 bytes --] PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 *14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 14 *15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 *7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 12 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report system 00:01: ioport range 0x4d0-0x4d1 has been reserved system 00:01: ioport range 0x290-0x29f has been reserved system 00:01: ioport range 0x800-0x87f has been reserved system 00:01: ioport range 0x290-0x294 has been reserved system 00:01: ioport range 0x880-0x88f has been reserved system 00:08: ioport range 0x400-0x4bf could not be reserved system 00:09: iomem range 0xe0000000-0xe3ffffff could not be reserved system 00:0a: iomem range 0xd1e00-0xd3fff has been reserved system 00:0a: iomem range 0xf0000-0xf7fff could not be reserved system 00:0a: iomem range 0xf8000-0xfbfff could not be reserved system 00:0a: iomem range 0xfc000-0xfffff could not be reserved system 00:0a: iomem range 0xcfee0000-0xcfefffff could not be reserved system 00:0a: iomem range 0x0-0x9ffff could not be reserved system 00:0a: iomem range 0x100000-0xcfedffff could not be reserved system 00:0a: iomem range 0xfec00000-0xfec00fff could not be reserved system 00:0a: iomem range 0xfed10000-0xfed1dfff could not be reserved system 00:0a: iomem range 0xfed20000-0xfed8ffff could not be reserved system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved system 00:0a: iomem range 0xffb00000-0xffb7ffff could not be reserved system 00:0a: iomem range 0xfff00000-0xffffffff could not be reserved system 00:0a: iomem range 0xe0000-0xeffff has been reserved PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: 0xe4000000-0xe6ffffff PREFETCH window: 0x00000000d0000000-0x00000000dfffffff PCI: Bridge: 0000:00:06.0 IO window: a000-afff MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.0 IO window: c000-cfff MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.3 IO window: b000-bfff MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.4 IO window: d000-dfff MEM window: 0xe7000000-0xe7ffffff PREFETCH window: 0x00000000e8000000-0x00000000e80fffff PCI: Bridge: 0000:00:1e.0 IO window: disabled. MEM window: 0xe8100000-0xe81fffff PREFETCH window: disabled. ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:01.0 to 64 ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:06.0 to 64 ACPI: PCI Interrupt 0000:00:1c.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1c.0 to 64 ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 15 PCI: setting IRQ 15 as level-triggered ACPI: PCI Interrupt 0000:00:1c.3[D] -> Link [LNKD] -> GSI 15 (level, low) -> IRQ 15 PCI: Setting latency timer of device 0000:00:1c.3 to 64 ACPI: PCI Interrupt 0000:00:1c.4[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1c.4 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered highmem bounce pool size: 64 pages SGI XFS with ACLs, no debug enabled io scheduler noop registered io scheduler cfq registered (default) pci 0000:01:00.0: Boot video device PCI: Setting latency timer of device 0000:00:01.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:01.0:pcie00] Allocate Port Service[0000:00:01.0:pcie03] PCI: Setting latency timer of device 0000:00:06.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:06.0:pcie00] Allocate Port Service[0000:00:06.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] Allocate Port Service[0000:00:1c.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.3 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.3:pcie00] Allocate Port Service[0000:00:1c.3:pcie02] Allocate Port Service[0000:00:1c.3:pcie03] PCI: Setting latency timer of device 0000:00:1c.4 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.4:pcie00] Allocate Port Service[0000:00:1c.4:pcie02] Allocate Port Service[0000:00:1c.4:pcie03] Driver 'sd' needs updating - please use bus_type methods ahci 0000:00:1f.2: version 3.0 ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> GSI 15 (level, low) -> IRQ 15 Switched to high resolution mode on CPU 0 ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pmp pio slum part PCI: Setting latency timer of device 0000:00:1f.2 to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci scsi4 : ahci scsi5 : ahci ata1: SATA max UDMA/133 abar m2048@0xe8206000 port 0xe8206100 irq 15 ata2: SATA max UDMA/133 abar m2048@0xe8206000 port 0xe8206180 irq 15 ata3: SATA max UDMA/133 abar m2048@0xe8206000 port 0xe8206200 irq 15 ata4: SATA max UDMA/133 abar m2048@0xe8206000 port 0xe8206280 irq 15 ata5: SATA max UDMA/133 abar m2048@0xe8206000 port 0xe8206300 irq 15 ata6: SATA max UDMA/133 abar m2048@0xe8206000 port 0xe8206380 irq 15 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-6: ST3500320NS, SN04, max UDMA/133 ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: ATA-6: ST3500320NS, SN04, max UDMA/133 ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata2.00: configured for UDMA/133 ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) ata5: SATA link down (SStatus 0 SControl 300) ata6: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA ST3500320NS SN04 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk scsi 1:0:0:0: Direct-Access ATA ST3500320NS SN04 PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sdb2 sdb3 sd 1:0:0:0: [sdb] Attached SCSI disk ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 14 PCI: setting IRQ 14 as level-triggered ACPI: PCI Interrupt 0000:00:1a.7[C] -> Link [LNKC] -> GSI 14 (level, low) -> IRQ 14 PCI: Setting latency timer of device 0000:00:1a.7 to 64 ehci_hcd 0000:00:1a.7: EHCI Host Controller ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 PCI: cache line size of 32 is not supported by device 0000:00:1a.7 ehci_hcd 0000:00:1a.7: irq 14, io mem 0xe8205000 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNK1] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 5, io mem 0xe8204000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 6 ports detected USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1a.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1a.0 to 64 uhci_hcd 0000:00:1a.0: UHCI Host Controller uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1a.0: irq 11, io base 0x0000e200 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 7 PCI: setting IRQ 7 as level-triggered ACPI: PCI Interrupt 0000:00:1a.1[B] -> Link [LNKF] -> GSI 7 (level, low) -> IRQ 7 PCI: Setting latency timer of device 0000:00:1a.1 to 64 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1a.1: irq 7, io base 0x0000e000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1a.2[C] -> Link [LNKC] -> GSI 14 (level, low) -> IRQ 14 PCI: Setting latency timer of device 0000:00:1a.2 to 64 uhci_hcd 0000:00:1a.2: UHCI Host Controller uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1a.2: irq 14, io base 0x0000e100 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNK1] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 uhci_hcd 0000:00:1d.0: irq 5, io base 0x0000e300 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 15 (level, low) -> IRQ 15 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 uhci_hcd 0000:00:1d.1: irq 15, io base 0x0000e400 usb usb7: configuration #1 chosen from 1 choice hub 7-0:1.0: USB hub found hub 7-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 14 (level, low) -> IRQ 14 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 uhci_hcd 0000:00:1d.2: irq 14, io base 0x0000e500 usb usb8: configuration #1 chosen from 1 choice hub 8-0:1.0: USB hub found hub 8-0:1.0: 2 ports detected PNP: PS/2 Controller [PNP0f13:PS2M] at 0x60,0x64 irq 12 PNP: PS/2 controller doesn't have KBD irq; using default 1 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice md: raid1 personality registered for level 1 cpuidle: using governor ladder usb 8-2: new low speed USB device using uhci_hcd and address 2 usb 8-2: configuration #1 chosen from 1 choice input: Logitech Logitech USB Keyboard as /class/input/input0 input: USB HID v1.10 Keyboard [Logitech Logitech USB Keyboard] on usb-0000:00:1d.2-2 input: Logitech Logitech USB Keyboard as /class/input/input1 input: USB HID v1.10 Mouse [Logitech Logitech USB Keyboard] on usb-0000:00:1d.2-2 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode input: ImPS/2 Generic Wheel Mouse as /class/input/input2 md: Autodetecting RAID arrays. md: Scanned 6 and added 6 devices. md: autorun ... md: considering sdb3 ... md: adding sdb3 ... md: sdb2 has different UUID to sdb3 md: sdb1 has different UUID to sdb3 md: adding sda3 ... md: sda2 has different UUID to sdb3 md: sda1 has different UUID to sdb3 md: created md2 md: bind<sda3> md: bind<sdb3> md: running: <sdb3><sda3> raid1: raid set md2 active with 2 out of 2 mirrors md: considering sdb2 ... md: adding sdb2 ... md: sdb1 has different UUID to sdb2 md: adding sda2 ... md: sda1 has different UUID to sdb2 md: created md1 md: bind<sda2> md: bind<sdb2> md: running: <sdb2><sda2> raid1: raid set md1 active with 2 out of 2 mirrors md: considering sdb1 ... md: adding sdb1 ... md: adding sda1 ... md: created md0 md: bind<sda1> md: bind<sdb1> md: running: <sdb1><sda1> raid1: raid set md0 active with 2 out of 2 mirrors md: ... autorun DONE. Filesystem "md1": Disabling barriers, not supported by the underlying device XFS mounting filesystem md1 Ending clean XFS mount for filesystem: md1 VFS: Mounted root (xfs filesystem) readonly. Freeing unused kernel memory: 204k freed ACPI: ACPI0007:00 is registered as cooling_device0 ACPI: Processor [CPU0] (supports 8 throttling states) input: Power Button (FF) as /class/input/input3 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input4 ACPI: Power Button (CM) [PWRB] r8169 Gigabit Ethernet driver 2.2LK loaded ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:05:00.0 to 64 r8169 0000:05:00.0: no MSI. Back to INTx. eth0: RTL8168c/8111c at 0xf8864000, 00:1d:7d:06:7b:39, XID 3c2000c0 IRQ 11 ACPI: PCI Interrupt Link [LNK0] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNK0] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1b.0 to 64 hda_codec: Unknown model for ALC882, trying auto-probe from BIOS... Filesystem "md1": Disabling barriers, not supported by the underlying device r8169: eth0: link up r8169: eth0: link up ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Realtek 8111c weirdness problems, apic/msi, and normal bug 2008-04-11 1:11 ` Kasper Sandberg @ 2008-04-11 18:06 ` Kasper Sandberg 2008-04-12 12:23 ` Kasper Sandberg 2008-04-12 19:22 ` Francois Romieu 1 sibling, 1 reply; 9+ messages in thread From: Kasper Sandberg @ 2008-04-11 18:06 UTC (permalink / raw) To: Francois Romieu; +Cc: Andrew Morton, LKML Mailinglist, linux-acpi, netdev [-- Attachment #1: Type: text/plain, Size: 1595 bytes --] I've got more information again. This is dmesg, and /proc/interrupts from a livecd (systemrescuecd), its a .23.14, and only 1 nic works (the one that doesent work on .25 noapic/msi), the other gets detected as fiber.. strangely enough, the link detection works on the working nic, on .23.14. attached are /proc/interrupts and dmesg.. oh, and this is a 64bit livecd kernel, but it appears to act the same on the 32bit kernel on the livecd.. This, and the previous information i have given, does it give a clue as to what may be happening here? from what i can see, it may be either interrupts or that pci warning thingie... it appears that on the livecd, which runs with both msi and apic, that the ethernet controllers gets its interrupt setup with apic, whereas msi likes to catch it on my own .25 kernel, allthough its abit weird what happens.. If you need more information, just ask :) On Fri, 2008-04-11 at 03:11 +0200, Kasper Sandberg wrote: > Sorry for top posting, but its just easier in this case :) > <snip> > > > > > > > > > > > > > > -- > > > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > > > the body of a message to majordomo@vger.kernel.org > > > More majordomo info at http://vger.kernel.org/majordomo-info.html > > > Please read the FAQ at http://www.tux.org/lkml/ > > > > -- > > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > > the body of a message to majordomo@vger.kernel.org > > More majordomo info at http://vger.kernel.org/majordomo-info.html > > Please read the FAQ at http://www.tux.org/lkml/ [-- Attachment #2: dmesg_64bit_weird --] [-- Type: text/plain, Size: 26933 bytes --] Linux version 2.6.23.14-fd12-amd64 (root@gentoo64) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.1)) #1 SMP Wed Jan 16 22:45:41 UTC 2008 Command line: initrd=rescue64.igz video=ofonly vga=0 cdroot BOOT_IMAGE=rescue64 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009e800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000cfee0000 (usable) BIOS-e820: 00000000cfee0000 - 00000000cfee3000 (ACPI NVS) BIOS-e820: 00000000cfee3000 - 00000000cfef0000 (ACPI data) BIOS-e820: 00000000cfef0000 - 00000000cff00000 (reserved) BIOS-e820: 00000000e0000000 - 00000000e4000000 (reserved) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) BIOS-e820: 0000000100000000 - 0000000130000000 (usable) Entering add_active_range(0, 0, 158) 0 entries of 256 used Entering add_active_range(0, 256, 851680) 1 entries of 256 used Entering add_active_range(0, 1048576, 1245184) 2 entries of 256 used end_pfn_map = 1245184 DMI 2.4 present. ACPI: RSDP 000F6EB0, 0014 (r0 GBT ) ACPI: RSDT CFEE3040, 0034 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) ACPI: FACP CFEE30C0, 0074 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) ACPI: DSDT CFEE3180, 4C2E (r1 GBT GBTUACPI 1000 MSFT 100000C) ACPI: FACS CFEE0000, 0040 ACPI: HPET CFEE7F00, 0038 (r1 GBT GBTUACPI 42302E31 GBTU 98) ACPI: MCFG CFEE7F80, 003C (r1 GBT GBTUACPI 42302E31 GBTU 1010101) ACPI: APIC CFEE7E00, 0084 (r1 GBT GBTUACPI 42302E31 GBTU 1010101) Entering add_active_range(0, 0, 158) 0 entries of 256 used Entering add_active_range(0, 256, 851680) 1 entries of 256 used Entering add_active_range(0, 1048576, 1245184) 2 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 DMA32 4096 -> 1048576 Normal 1048576 -> 1245184 Movable zone start PFN for each node early_node_map[3] active PFN ranges 0: 0 -> 158 0: 256 -> 851680 0: 1048576 -> 1245184 On node 0 totalpages: 1048190 DMA zone: 56 pages used for memmap DMA zone: 2501 pages reserved DMA zone: 1441 pages, LIFO batch:0 DMA32 zone: 14280 pages used for memmap DMA32 zone: 833304 pages, LIFO batch:31 Normal zone: 2688 pages used for memmap Normal zone: 193920 pages, LIFO batch:31 Movable zone: 0 pages used for memmap ACPI: PM-Timer IO Port: 0x408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 (Bootup-CPU) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled) ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Setting APIC routing to flat ACPI: HPET id: 0x8086a201 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at e6000000 (gap: e4000000:1ac00000) SMP: Allowing 4 CPUs, 3 hotplug CPUs PERCPU: Allocating 36568 bytes of per cpu data Built 1 zonelists in Zone order. Total pages: 1028665 Kernel command line: initrd=rescue64.igz video=ofonly vga=0 cdroot BOOT_IMAGE=rescue64 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) hpet clockevent registered TSC calibrated against HPET time.c: Detected 1600.055 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) Checking aperture... PCI-DMA: Using software bounce buffering for IO (SWIOTLB) Placing software IO TLB between 0x58de000 - 0x98de000 Memory: 4040004k/4980736k available (5463k kernel code, 152444k reserved, 3293k data, 276k init) SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=4, Nodes=1 Calibrating delay using timer specific routine.. 3202.16 BogoMIPS (lpj=1601081) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 256 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 512K using mwait in idle threads. CPU0: Thermal monitoring enabled (TM2) SMP alternatives: switching to UP code ACPI: Core revision 20070126 Using local APIC timer interrupts. APIC timer calibration result 12500427 Detected 12.500 MHz APIC timer. Brought up 1 CPUs sizeof(vma)=168 bytes sizeof(page)=56 bytes sizeof(inode)=560 bytes sizeof(dentry)=208 bytes sizeof(ext3inode)=760 bytes sizeof(buffer_head)=104 bytes sizeof(skbuff)=232 bytes sizeof(task_struct)=2048 bytes khelper used greatest stack depth: 6584 bytes left khelper used greatest stack depth: 6528 bytes left NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG at e0000000 - e3ffffff ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S3 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX5._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 14 *15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 *14 15) ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 *7 9 10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 12 devices ACPI: ACPI bus type pnp unregistered Generic PHY: Registered new driver SCSI subsystem initialized libata version 2.21 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default PCI-GART: No AMD northbridge found. hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0 hpet0: 4 64-bit timers, 14318180 Hz Time: tsc clocksource has been installed. pnp: 00:08: ioport range 0x400-0x4bf has been reserved pnp: 00:09: iomem range 0xe0000000-0xe3ffffff could not be reserved pnp: 00:0a: iomem range 0xd1e00-0xd3fff has been reserved pnp: 00:0a: iomem range 0xf0000-0xf7fff could not be reserved pnp: 00:0a: iomem range 0xf8000-0xfbfff could not be reserved pnp: 00:0a: iomem range 0xfc000-0xfffff could not be reserved PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: e4000000-e6ffffff PREFETCH window: d0000000-dfffffff PCI: Bridge: 0000:00:06.0 IO window: 9000-9fff MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.0 IO window: b000-bfff MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.3 IO window: a000-afff MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.4 IO window: c000-cfff MEM window: e7000000-e7ffffff PREFETCH window: e9000000-e90fffff PCI: Bridge: 0000:00:1c.5 IO window: d000-dfff MEM window: e8000000-e8ffffff PREFETCH window: e9100000-e91fffff PCI: Bridge: 0000:00:1e.0 IO window: disabled. MEM window: e9200000-e92fffff PREFETCH window: disabled. ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:01.0 to 64 ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:06.0 to 64 ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1c.0 to 64 ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1c.3 to 64 ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1c.4 to 64 ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1c.5 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) TCP established hash table entries: 131072 (order: 9, 3145728 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered checking if image is initramfs... it is Freeing initrd memory: 1870k freed audit: initializing netlink socket (disabled) audit(1207739006.467:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Loading Reiser4. See www.namesys.com for a description of Reiser4. squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher squashfs: LZMA suppport for slax.org by jro NTFS driver 2.1.28 [Flags: R/O]. fuse init (API version 7.8) SELinux: Registering netfilter hooks ksign: Installing public key data Loading keyring io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Boot video device is 0000:01:00.0 PCI: Setting latency timer of device 0000:00:01.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:01.0:pcie00] Allocate Port Service[0000:00:01.0:pcie03] PCI: Setting latency timer of device 0000:00:06.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:06.0:pcie00] Allocate Port Service[0000:00:06.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] Allocate Port Service[0000:00:1c.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.3 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.3:pcie00] Allocate Port Service[0000:00:1c.3:pcie02] Allocate Port Service[0000:00:1c.3:pcie03] PCI: Setting latency timer of device 0000:00:1c.4 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.4:pcie00] Allocate Port Service[0000:00:1c.4:pcie02] Allocate Port Service[0000:00:1c.4:pcie03] PCI: Setting latency timer of device 0000:00:1c.5 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.5:pcie00] Allocate Port Service[0000:00:1c.5:pcie02] Allocate Port Service[0000:00:1c.5:pcie03] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 ACPI: Processor [CPU0] (supports 8 throttling states) ACPI Exception (processor_core-0819): AE_NOT_FOUND, Processor Device is not present [20070126] ACPI Exception (processor_core-0819): AE_NOT_FOUND, Processor Device is not present [20070126] ACPI Exception (processor_core-0819): AE_NOT_FOUND, Processor Device is not present [20070126] Real Time Clock Driver v1.12ac hpet_resources: 0xfed00000 is busy Non-volatile memory driver v1.2 Linux agpgart interface v0.102 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize loop: module loaded Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI Copyright (c) 1999-2006 Intel Corporation. Intel(R) PRO/1000 Network Driver - 0.2.0 Copyright (c) 1999-2007 Intel Corporation. Intel(R) PRO/10GbE Network Driver - version 1.0.126-k2-NAPI Copyright (c) 1999-2006 Intel Corporation. pcnet32.c:v1.33-NAPI 27.Jun.2006 tsbogend@alpha.franken.de e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI e100: Copyright(c) 1999-2006 Intel Corporation ns83820.c: National Semiconductor DP83820 10/100/1000 driver. Marvell 88E1101: Registered new driver Marvell 88E1112: Registered new driver Marvell 88E1111: Registered new driver Marvell 88E1145: Registered new driver Davicom DM9161E: Registered new driver Davicom DM9161A: Registered new driver Davicom DM9131: Registered new driver Cicada Cis8204: Registered new driver Cicada Cis8201: Registered new driver LXT970: Registered new driver LXT971: Registered new driver QS6612: Registered new driver SMSC LAN83C185: Registered new driver Vitesse VSC8244: Registered new driver Switched to high resolution mode on CPU 0 Broadcom BCM5411: Registered new driver Broadcom BCM5421: Registered new driver Broadcom BCM5461: Registered new driver forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60. Silan SC92031 PCI Fast Ethernet Adapter driver 2.0c r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:05:00.0 to 64 eth0: RTL8168b/8111b at 0xffffc20000022000, 00:1d:7d:06:7b:39, XID 3c2000c0 IRQ 16 r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:06:00.0 to 64 eth1: RTL8168b/8111b at 0xffffc20000024000, 00:1d:7d:06:75:d8, XID 3c2000c0 IRQ 17 myri10ge: Version 1.3.2-1.269 dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17) winbond-840.c:v1.01-e (2.4 port) Sep-11-2006 Donald Becker <becker@scyld.com> http://www.scyld.com/network/drivers.html uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29) input: Macintosh mouse button emulation as /class/input/input0 Loading iSCSI transport class v2.0-724. Adaptec aacraid driver 1.1-5[2449]-ms aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded scsi: <fdomain> Detection failed (no card) QLogic Fibre Channel HBA Driver iscsi: registered transport (qla4xxx) QLogic iSCSI HBA Driver Emulex LightPulse Fibre Channel SCSI driver 8.2.2 Copyright(c) 2004-2007 Emulex. All rights reserved. DC390: clustering now enabled by default. If you get problems load with "disable_clustering=1" and report to maintainers megasas: 00.00.03.10-rc5 Thu May 17 10:09:32 PDT 2007 GDT-HA: Storage RAID Controller Driver. Version: 3.05 GDT-HA: Found 0 PCI Storage RAID Controllers 3ware Storage Controller device driver for Linux v1.26.02.002. 3ware 9000 Storage Controller device driver for Linux v2.26.02.010. RocketRAID 3xxx SATA Controller driver v1.0 (060426) stex: Promise SuperTrak EX Driver version: 3.6.0000.1 ahci 0000:00:1f.2: version 2.3 ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19 ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pmp pio slum part PCI: Setting latency timer of device 0000:00:1f.2 to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci scsi4 : ahci scsi5 : ahci ata1: SATA max UDMA/133 cmd 0xffffc20000026100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1273 ata2: SATA max UDMA/133 cmd 0xffffc20000026180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1273 ata3: SATA max UDMA/133 cmd 0xffffc20000026200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1273 ata4: SATA max UDMA/133 cmd 0xffffc20000026280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1273 ata5: SATA max UDMA/133 cmd 0xffffc20000026300 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1273 ata6: SATA max UDMA/133 cmd 0xffffc20000026380 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1273 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-6: ST3500320NS, SN04, max UDMA/133 ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: ATA-6: ST3500320NS, SN04, max UDMA/133 ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata2.00: configured for UDMA/133 ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) ata5: SATA link down (SStatus 0 SControl 300) ata6: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA ST3500320NS SN04 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 1:0:0:0: Direct-Access ATA ST3500320NS SN04 PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sdb2 sdb3 sd 1:0:0:0: [sdb] Attached SCSI disk sd 1:0:0:0: Attached scsi generic sg1 type 0 Fusion MPT base driver 3.04.05 Copyright (c) 1999-2007 LSI Logic Corporation Fusion MPT SPI Host driver 3.04.05 Fusion MPT FC Host driver 3.04.05 Fusion MPT SAS Host driver 3.04.05 Fusion MPT misc device (ioctl) driver 3.04.05 mptctl: Registered with Fusion MPT base driver mptctl: /dev/mptctl @ (major,minor=10,220) Fusion MPT LAN driver 3.04.05 ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1a.7 to 64 ehci_hcd 0000:00:1a.7: EHCI Host Controller ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 PCI: cache line size of 32 is not supported by device 0000:00:1a.7 ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe9305000 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe9304000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 6 ports detected 116x: driver isp116x-hcd, 03 Nov 2005 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1a.0 to 64 uhci_hcd 0000:00:1a.0: UHCI Host Controller uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000e100 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usb 1-1: new high speed USB device using ehci_hcd and address 2 ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1a.1 to 64 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000e200 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected usb 1-1: configuration #1 chosen from 1 choice ACPI: PCI Interrupt 0000:00:1a.2[C] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1a.2 to 64 uhci_hcd 0000:00:1a.2: UHCI Host Controller uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000e000 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e300 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e400 usb usb7: configuration #1 chosen from 1 choice hub 7-0:1.0: USB hub found hub 7-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e500 usb usb8: configuration #1 chosen from 1 choice hub 8-0:1.0: USB hub found hub 8-0:1.0: 2 ports detected sl811: driver sl811-hcd, 19 May 2005 Initializing USB Mass Storage driver... scsi6 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning usb 8-2: new low speed USB device using uhci_hcd and address 2 usb 8-2: configuration #1 chosen from 1 choice usbcore: registered new interface driver usb-storage USB Mass Storage support registered. PNP: PS/2 Controller [PNP0f13:PS2M] at 0x60,0x64 irq 12 PNP: PS/2 controller doesn't have KBD irq; using default 1 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice usbcore: registered new interface driver hiddev input: Logitech Logitech USB Keyboard as /class/input/input1 input: USB HID v1.10 Keyboard [Logitech Logitech USB Keyboard] on usb-0000:00:1d.2-2 input: Logitech Logitech USB Keyboard as /class/input/input2 input: USB HID v1.10 Mouse [Logitech Logitech USB Keyboard] on usb-0000:00:1d.2-2 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Freeing unused kernel memory: 276k freed Write protecting the kernel read-only data: 2192k mount used greatest stack depth: 6448 bytes left mount used greatest stack depth: 6016 bytes left ata1: soft resetting port ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: configured for UDMA/133 ata1: EH complete sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA input: ImPS/2 Generic Wheel Mouse as /class/input/input3 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com JFS: nTxBlock = 8192, nTxLock = 65536 SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled SGI XFS Quota Management subsystem mount used greatest stack depth: 5896 bytes left mount used greatest stack depth: 5880 bytes left UDF-fs: No VRS found mount used greatest stack depth: 4160 bytes left UDF-fs: No VRS found XFS mounting filesystem sda1 Ending clean XFS mount for filesystem: sda1 UDF-fs: No VRS found XFS mounting filesystem sda2 Ending clean XFS mount for filesystem: sda2 usb-storage: device scan complete scsi 6:0:0:0: CD-ROM ATAPI DVD A DH20A4P 9P54 PQ: 0 ANSI: 0 sr0: scsi3-mmc drive: 16x/48x writer dvd-ram cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 6:0:0:0: Attached scsi CD-ROM sr0 sr 6:0:0:0: Attached scsi generic sg2 type 5 attempt to access beyond end of device sda3: rw=0, want=18446744073705357316, limit=927448515 UDF-fs: No VRS found UDF-fs: No VRS found UDF-fs: No VRS found XFS mounting filesystem sdb1 Ending clean XFS mount for filesystem: sdb1 UDF-fs: No VRS found XFS mounting filesystem sdb2 Ending clean XFS mount for filesystem: sdb2 attempt to access beyond end of device sdb3: rw=0, want=18446744073705357316, limit=927448515 UDF-fs: No VRS found ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A input: Power Button (FF) as /class/input/input4 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input5 ACPI: Power Button (CM) [PWRB] iTCO_vendor_support: vendor-support=0 iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007) iTCO_wdt: failed to reset NO_REBOOT flag, reboot disabled by hardware iTCO_wdt: No card detected ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18 input: PC Speaker as /class/input/input6 ACPI: PCI Interrupt 0000:07:06.0[A] -> GSI 18 (level, low) -> IRQ 18 firewire_ohci: Added fw-ohci device 0000:07:06.0, OHCI version 1.10 firewire_core: created new fw device fw0 (0 config rom retries, S400) nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:01:00.0 to 64 NVRM: loading NVIDIA UNIX x86_64 Kernel Module 100.14.19 Wed Sep 12 14:08:38 PDT 2007 r8169: eth1: link down r8169: eth0: link down Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: starting 90-second grace period NET: Registered protocol family 10 lo: Disabled Privacy Extensions ADDRCONF(NETDEV_UP): eth0: link is not ready ADDRCONF(NETDEV_UP): eth1: link is not ready r8169: eth1: link up ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready eth1: no IPv6 routers present r8169: eth1: link down r8169: eth1: link up r8169: eth0: link down r8169: eth0: link down ADDRCONF(NETDEV_UP): eth0: link is not ready [-- Attachment #3: ints --] [-- Type: text/plain, Size: 673 bytes --] CPU0 0: 167 IO-APIC-edge timer 1: 2 IO-APIC-edge i8042 8: 29 IO-APIC-edge rtc 9: 0 IO-APIC-fasteoi acpi 12: 113 IO-APIC-edge i8042 16: 0 IO-APIC-fasteoi uhci_hcd:usb3 17: 9 IO-APIC-fasteoi eth1 18: 6341 IO-APIC-fasteoi ehci_hcd:usb1, uhci_hcd:usb5, uhci_hcd:usb8, firewire_ohci 19: 0 IO-APIC-fasteoi uhci_hcd:usb7 21: 0 IO-APIC-fasteoi uhci_hcd:usb4 23: 2 IO-APIC-fasteoi ehci_hcd:usb2, uhci_hcd:usb6 1273: 2099045 PCI-MSI-edge ahci NMI: 0 LOC: 68257 ERR: 0 [-- Attachment #4: ints2 --] [-- Type: text/plain, Size: 679 bytes --] CPU0 0: 167 IO-APIC-edge timer 1: 2 IO-APIC-edge i8042 8: 29 IO-APIC-edge rtc 9: 0 IO-APIC-fasteoi acpi 12: 113 IO-APIC-edge i8042 16: 1 IO-APIC-fasteoi uhci_hcd:usb3, eth0 17: 9 IO-APIC-fasteoi eth1 18: 6383 IO-APIC-fasteoi ehci_hcd:usb1, uhci_hcd:usb5, uhci_hcd:usb8, firewire_ohci 19: 0 IO-APIC-fasteoi uhci_hcd:usb7 21: 0 IO-APIC-fasteoi uhci_hcd:usb4 23: 2 IO-APIC-fasteoi ehci_hcd:usb2, uhci_hcd:usb6 1273: 2099045 PCI-MSI-edge ahci NMI: 0 LOC: 68322 ERR: 0 ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Realtek 8111c weirdness problems, apic/msi, and normal bug 2008-04-11 18:06 ` Kasper Sandberg @ 2008-04-12 12:23 ` Kasper Sandberg 0 siblings, 0 replies; 9+ messages in thread From: Kasper Sandberg @ 2008-04-12 12:23 UTC (permalink / raw) To: Francois Romieu; +Cc: Andrew Morton, LKML Mailinglist, linux-acpi, netdev I've got some more information (though probably not too helpful). Realtek has modified(i probably mentioned this earlier) the r8169 driver, under the name of r8168. It might be worth checking out what they have done. people are reporting that it works: http://damienkane.livejournal.com/5574.html http://www.mail-archive.com/ubuntu-bugs% 40lists.ubuntu.com/msg730229.html the driver can be found at: http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=13&PFid=5&Level=5&Conn=4&DownTypeID=3&GetDown=false if that doesent work, do: http://www.realtek.com.tw/downloads -> communication networks ics -> network interface controllers -> 10/100/1000 gigabit ethernet -> pci express. I will try myself, but i have zero knowledge about this stuff in the kernel, and will probably not be able to find anything of use. On Fri, 2008-04-11 at 20:06 +0200, Kasper Sandberg wrote: > I've got more information again. This is dmesg, and /proc/interrupts > from a livecd (systemrescuecd), its a .23.14, and only 1 nic works (the <snip> > > On Fri, 2008-04-11 at 03:11 +0200, Kasper Sandberg wrote: > > Sorry for top posting, but its just easier in this case :) > > > <snip> > > > > > > > > > > > > > > > > > > > -- > > > > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > > > > the body of a message to majordomo@vger.kernel.org > > > > More majordomo info at http://vger.kernel.org/majordomo-info.html > > > > Please read the FAQ at http://www.tux.org/lkml/ > > > > > > -- > > > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > > > the body of a message to majordomo@vger.kernel.org > > > More majordomo info at http://vger.kernel.org/majordomo-info.html > > > Please read the FAQ at http://www.tux.org/lkml/ ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Realtek 8111c weirdness problems, apic/msi, and normal bug 2008-04-11 1:11 ` Kasper Sandberg 2008-04-11 18:06 ` Kasper Sandberg @ 2008-04-12 19:22 ` Francois Romieu 2008-04-12 22:02 ` Kasper Sandberg 1 sibling, 1 reply; 9+ messages in thread From: Francois Romieu @ 2008-04-12 19:22 UTC (permalink / raw) To: Kasper Sandberg; +Cc: Andrew Morton, LKML Mailinglist, linux-acpi, netdev Kasper Sandberg <lkml@metanurb.dk> : > Sorry for top posting, but its just easier in this case :) Tsk, tsk. > I may have just gotten some new information to share. > > I just built -git8. and the nic didnt work.. by booting with > noapic/nomsi i got it running though. then i did some tests, and > rebooted into the default(has worked mostly for me) noapic/msi boot. > Then it worked. Can you try a simple 'nomsi' boot ? The lspci in your previous message (2008/04/10) suggested that something was very wrong at the PCI level: [...] 05:00.0 0200: 10ec:8168 (rev ff) (prog-if ff) !!! Unknown header type 7f Kernel driver in use: r8169 Kernel modules: r8169 00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff (but this was on an older kernel, right ?) When you see such an output, can you try to see if the direct access option of lspci (-H{1/2}) makes a difference ? [...] > if its a boot where the nic works, i can usually rmmod/modprobe the > module once without it giving error, however if its a boot where the nic > doesent work, first time i rmmod and modprobe, it gives me an error.. > > the error is: > PCI: cache line size of 32 is not supported by device 0000:05:00.0 > ACPI: PCI interrupt for device 0000:05:00.0 disabled > r8169: probe of 0000:05:00.0 failed with error -22 What does lspci say here ? > I have attached some dmesgs(sorry, but my client messes up inlines..) > also.. link detecting isnt working properly, sometimes it will detect a > link as down after a while.. its quite weird.. (please increase the size of your kernel log buffer) > (oh, and this time its without nvidia just to be 100000% sure) Thanks. > I hope this can help to get it resolved, alot of people are having > problems with these controllers.. i can however confirm that a similar > controller is working perfectly on a friends gigabyte motherboard, thats > with P35 chipset though, i have X48. He has only 1 of them onboard. You can ask your friend to grep for the 'XID' line in the kernel log written by the r8169 driver. If the values match, you have got the same 816x hardware. There are different problems with the 8168 - older kernel with broken mmconfig / msi / etc. - newer 8168 chipsets which are currently not correctly handled - plain 8168 driver bugs - ... (that being said, it really works for some users too) > also something which may be of interrest, realtek offers a modified > r8169 driver called "r8168", which supposedly fixes this. I have been > unable to get it to compile though, but i saw it on ubuntu forums. I am looking very closely at Realtek's drivers but the diff between the different revisions of their 8168 driver are not always as readable as I would hope for (things have improved though). Realtek is working at fixing its 8168 driver for recent kernels. It should be easier to compare its behavior against the in-kernel driver with recent kernels soon. It will makes everybody's life easier. -- Ueimor ^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: Realtek 8111c weirdness problems, apic/msi, and normal bug 2008-04-12 19:22 ` Francois Romieu @ 2008-04-12 22:02 ` Kasper Sandberg 0 siblings, 0 replies; 9+ messages in thread From: Kasper Sandberg @ 2008-04-12 22:02 UTC (permalink / raw) To: Francois Romieu; +Cc: Andrew Morton, LKML Mailinglist, linux-acpi, netdev On Sat, 2008-04-12 at 21:22 +0200, Francois Romieu wrote: > Kasper Sandberg <lkml@metanurb.dk> : > > Sorry for top posting, but its just easier in this case :) > > Tsk, tsk. > > > I may have just gotten some new information to share. > > > > I just built -git8. and the nic didnt work.. by booting with > > noapic/nomsi i got it running though. then i did some tests, and > > rebooted into the default(has worked mostly for me) noapic/msi boot. > > Then it worked. > > Can you try a simple 'nomsi' boot ? first off, isnt it pci=nomsi? it still appears to be using msi when booting with nomsi. anyway, i did as you asked. I have now booted with a multitude of parameters and combinations, dumped lots of information and done tests. > > The lspci in your previous message (2008/04/10) suggested that > something was very wrong at the PCI level: > [...] > 05:00.0 0200: 10ec:8168 (rev ff) (prog-if ff) > !!! Unknown header type 7f > Kernel driver in use: r8169 > Kernel modules: r8169 > 00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > > (but this was on an older kernel, right ?) > > When you see such an output, can you try to see if the direct access > option of lspci (-H{1/2}) makes a difference ? i have dumped with both. > > [...] > > if its a boot where the nic works, i can usually rmmod/modprobe the > > module once without it giving error, however if its a boot where the nic > > doesent work, first time i rmmod and modprobe, it gives me an error.. > > > > the error is: > > PCI: cache line size of 32 is not supported by device 0000:05:00.0 > > ACPI: PCI interrupt for device 0000:05:00.0 disabled > > r8169: probe of 0000:05:00.0 failed with error -22 > > What does lspci say here ? all in the dumps :) > > > I have attached some dmesgs(sorry, but my client messes up inlines..) > > also.. link detecting isnt working properly, sometimes it will detect a > > link as down after a while.. its quite weird.. > > (please increase the size of your kernel log buffer) done. > > > (oh, and this time its without nvidia just to be 100000% sure) > > Thanks. > > > I hope this can help to get it resolved, alot of people are having > > problems with these controllers.. i can however confirm that a similar > > controller is working perfectly on a friends gigabyte motherboard, thats > > with P35 chipset though, i have X48. He has only 1 of them onboard. > > You can ask your friend to grep for the 'XID' line in the kernel log > written by the r8169 driver. If the values match, you have got the same > 816x hardware. I shall do as soon as he comes online. > > There are different problems with the 8168 > - older kernel with broken mmconfig / msi / etc. > - newer 8168 chipsets which are currently not correctly handled > - plain 8168 driver bugs > - ... > > (that being said, it really works for some users too) > > > also something which may be of interrest, realtek offers a modified > > r8169 driver called "r8168", which supposedly fixes this. I have been > > unable to get it to compile though, but i saw it on ubuntu forums. > > I am looking very closely at Realtek's drivers but the diff between > the different revisions of their 8168 driver are not always as > readable as I would hope for (things have improved though). okay.. well, i just thought i'd mention it, to be honest, i have more faith in you than realtek :) the information i have dumped is too substantial to have inline in mail, and also, my mail client destroys whitespace, so i have put up a tarball, which is available here: http://download1.kaspersandberg.com/r8169_debugging.tar.bz2 if you need more, for example, boots with "pci=nomsi" instead of just the nomsi parameter, or combinations, as always, feel free to ask, and i shall provide it. thanks! > > Realtek is working at fixing its 8168 driver for recent kernels. It > should be easier to compare its behavior against the in-kernel driver > with recent kernels soon. It will makes everybody's life easier. > ^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2008-04-12 22:04 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <1207407804.14885.27.camel@localhost>
2008-04-06 6:23 ` Realtek 8111c weirdness problems, apic/msi, and normal bug Andrew Morton
2008-04-06 14:06 ` Francois Romieu
2008-04-07 4:09 ` Kasper Sandberg
2008-04-10 12:17 ` Kasper Sandberg
2008-04-11 1:11 ` Kasper Sandberg
2008-04-11 18:06 ` Kasper Sandberg
2008-04-12 12:23 ` Kasper Sandberg
2008-04-12 19:22 ` Francois Romieu
2008-04-12 22:02 ` Kasper Sandberg
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).