* 2.6.27-rc1-git4 BUG: sched while atomic
@ 2008-08-04 16:48 Randy Dunlap
2008-08-04 17:17 ` Stephen Hemminger
2008-08-05 12:29 ` Rafael J. Wysocki
0 siblings, 2 replies; 8+ messages in thread
From: Randy Dunlap @ 2008-08-04 16:48 UTC (permalink / raw)
To: lkml; +Cc: netdev, mchan
Usually (e.g., in 2.6.27-rc1 & earlier), I see lots of these messages for
some reason:
tg3: eth2: Link is up at 1000 Mbps, full duplex.
tg3: eth2: Flow control is off for TX and off for RX.
tg3: eth3: Link is up at 1000 Mbps, full duplex.
tg3: eth3: Flow control is off for TX and off for RX.
bnx2: eth1: using MSI
bnx2: eth1 NIC SerDes Link is Up, 1000 Mbps full duplex
tg3: eth2: Link is up at 1000 Mbps, full duplex.
tg3: eth2: Flow control is off for TX and off for RX.
tg3: eth3: Link is up at 1000 Mbps, full duplex.
tg3: eth3: Flow control is off for TX and off for RX.
bnx2: eth1: using MSI
bnx2: eth1 NIC SerDes Link is Up, 1000 Mbps full duplex
tg3: eth2: Link is up at 1000 Mbps, full duplex.
tg3: eth2: Flow control is off for TX and off for RX.
tg3: eth3: Link is up at 1000 Mbps, full duplex.
tg3: eth3: Flow control is off for TX and off for RX.
bnx2: eth1: using MSI
bnx2: eth1 NIC SerDes Link is Up, 1000 Mbps full duplex
tg3: eth2: Link is up at 1000 Mbps, full duplex.
tg3: eth2: Flow control is off for TX and off for RX.
tg3: eth3: Link is up at 1000 Mbps, full duplex.
tg3: eth3: Flow control is off for TX and off for RX.
bnx2: eth1: using MSI
In 2.6.27-rc1-git4, I now see this (39 times):
BUG: scheduling while atomic: ifconfig/16971/0x00000100
Modules linked in: parport_pc lp parport tg3 lpfc cciss ehci_hcd ohci_hcd uhci_hcd
Pid: 16971, comm: ifconfig Not tainted 2.6.27-rc1-git4 #1
Call Trace:
[<ffffffff80283db9>] ? page_add_new_anon_rmap+0x20/0x22
[<ffffffff802310e9>] __schedule_bug+0x62/0x66
[<ffffffff80551146>] schedule+0x99/0x759
[<ffffffff8023dc9f>] ? __mod_timer+0xc1/0xd3
[<ffffffff8055584a>] ? do_page_fault+0x473/0x7dd
[<ffffffff80551ce4>] schedule_timeout+0x8d/0xb4
[<ffffffff8023d99e>] ? process_timeout+0x0/0xb
[<ffffffff80551cdf>] ? schedule_timeout+0x88/0xb4
[<ffffffff80551d24>] schedule_timeout_uninterruptible+0x19/0x1b
[<ffffffff8023dcc5>] msleep+0x14/0x1e
[<ffffffff80375f2f>] pci_set_power_state+0x1cd/0x292
[<ffffffff803739fc>] ? pci_bus_write_config_dword+0x64/0x73
[<ffffffffa00651b6>] tg3_set_power_state+0x58/0x884 [tg3]
[<ffffffff80552525>] ? __mutex_lock_slowpath+0x1d8/0x1e5
[<ffffffffa006b57a>] tg3_open+0x46/0x6cc [tg3]
[<ffffffff80552525>] ? __mutex_lock_slowpath+0x1d8/0x1e5
[<ffffffff804bdcfe>] dev_open+0x73/0xa8
[<ffffffff804bbf5e>] dev_change_flags+0xab/0x167
[<ffffffff804f7094>] devinet_ioctl+0x269/0x5da
[<ffffffff8026d9da>] ? unlock_page+0x2d/0x32
[<ffffffff804f7ca8>] inet_ioctl+0x92/0xaa
[<ffffffff804b2046>] sock_ioctl+0x1d1/0x1fb
[<ffffffff802a50aa>] vfs_ioctl+0x2a/0x77
[<ffffffff802a534c>] do_vfs_ioctl+0x255/0x272
[<ffffffff8055584a>] ? do_page_fault+0x473/0x7dd
[<ffffffff802a53ab>] sys_ioctl+0x42/0x67
[<ffffffff8020beeb>] system_call_fastpath+0x16/0x1b
---
~Randy
Linux Plumbers Conference, 17-19 September 2008, Portland, Oregon USA
http://linuxplumbersconf.org/
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: 2.6.27-rc1-git4 BUG: sched while atomic
2008-08-04 16:48 2.6.27-rc1-git4 BUG: sched while atomic Randy Dunlap
@ 2008-08-04 17:17 ` Stephen Hemminger
2008-08-04 14:20 ` Michael Chan
2008-08-04 18:00 ` Breno Leitao
2008-08-05 12:29 ` Rafael J. Wysocki
1 sibling, 2 replies; 8+ messages in thread
From: Stephen Hemminger @ 2008-08-04 17:17 UTC (permalink / raw)
To: Randy Dunlap; +Cc: netdev, mchan
On Mon, 4 Aug 2008 09:48:35 -0700
Randy Dunlap <randy.dunlap@oracle.com> wrote:
> Usually (e.g., in 2.6.27-rc1 & earlier), I see lots of these messages for
> some reason:
>
> tg3: eth2: Link is up at 1000 Mbps, full duplex.
> tg3: eth2: Flow control is off for TX and off for RX.
> tg3: eth3: Link is up at 1000 Mbps, full duplex.
> tg3: eth3: Flow control is off for TX and off for RX.
> bnx2: eth1: using MSI
> bnx2: eth1 NIC SerDes Link is Up, 1000 Mbps full duplex
> tg3: eth2: Link is up at 1000 Mbps, full duplex.
> tg3: eth2: Flow control is off for TX and off for RX.
> tg3: eth3: Link is up at 1000 Mbps, full duplex.
> tg3: eth3: Flow control is off for TX and off for RX.
> bnx2: eth1: using MSI
> bnx2: eth1 NIC SerDes Link is Up, 1000 Mbps full duplex
> tg3: eth2: Link is up at 1000 Mbps, full duplex.
> tg3: eth2: Flow control is off for TX and off for RX.
> tg3: eth3: Link is up at 1000 Mbps, full duplex.
> tg3: eth3: Flow control is off for TX and off for RX.
> bnx2: eth1: using MSI
> bnx2: eth1 NIC SerDes Link is Up, 1000 Mbps full duplex
> tg3: eth2: Link is up at 1000 Mbps, full duplex.
> tg3: eth2: Flow control is off for TX and off for RX.
> tg3: eth3: Link is up at 1000 Mbps, full duplex.
> tg3: eth3: Flow control is off for TX and off for RX.
> bnx2: eth1: using MSI
You have a bad cable or broken ethernet switch that is causing
the link to restart autonegotiation.
> In 2.6.27-rc1-git4, I now see this (39 times):
>
> BUG: scheduling while atomic: ifconfig/16971/0x00000100
> Modules linked in: parport_pc lp parport tg3 lpfc cciss ehci_hcd ohci_hcd uhci_hcd
> Pid: 16971, comm: ifconfig Not tainted 2.6.27-rc1-git4 #1
>
> Call Trace:
> [<ffffffff80283db9>] ? page_add_new_anon_rmap+0x20/0x22
> [<ffffffff802310e9>] __schedule_bug+0x62/0x66
> [<ffffffff80551146>] schedule+0x99/0x759
> [<ffffffff8023dc9f>] ? __mod_timer+0xc1/0xd3
> [<ffffffff8055584a>] ? do_page_fault+0x473/0x7dd
> [<ffffffff80551ce4>] schedule_timeout+0x8d/0xb4
> [<ffffffff8023d99e>] ? process_timeout+0x0/0xb
> [<ffffffff80551cdf>] ? schedule_timeout+0x88/0xb4
> [<ffffffff80551d24>] schedule_timeout_uninterruptible+0x19/0x1b
> [<ffffffff8023dcc5>] msleep+0x14/0x1e
> [<ffffffff80375f2f>] pci_set_power_state+0x1cd/0x292
> [<ffffffff803739fc>] ? pci_bus_write_config_dword+0x64/0x73
> [<ffffffffa00651b6>] tg3_set_power_state+0x58/0x884 [tg3]
> [<ffffffff80552525>] ? __mutex_lock_slowpath+0x1d8/0x1e5
> [<ffffffffa006b57a>] tg3_open+0x46/0x6cc [tg3]
> [<ffffffff80552525>] ? __mutex_lock_slowpath+0x1d8/0x1e5
> [<ffffffff804bdcfe>] dev_open+0x73/0xa8
> [<ffffffff804bbf5e>] dev_change_flags+0xab/0x167
> [<ffffffff804f7094>] devinet_ioctl+0x269/0x5da
> [<ffffffff8026d9da>] ? unlock_page+0x2d/0x32
> [<ffffffff804f7ca8>] inet_ioctl+0x92/0xaa
> [<ffffffff804b2046>] sock_ioctl+0x1d1/0x1fb
> [<ffffffff802a50aa>] vfs_ioctl+0x2a/0x77
> [<ffffffff802a534c>] do_vfs_ioctl+0x255/0x272
> [<ffffffff8055584a>] ? do_page_fault+0x473/0x7dd
> [<ffffffff802a53ab>] sys_ioctl+0x42/0x67
> [<ffffffff8020beeb>] system_call_fastpath+0x16/0x1b
This is a bug.
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: 2.6.27-rc1-git4 BUG: sched while atomic
2008-08-04 17:17 ` Stephen Hemminger
@ 2008-08-04 14:20 ` Michael Chan
2008-08-04 19:13 ` Breno Leitao
2008-08-04 21:40 ` David Miller
2008-08-04 18:00 ` Breno Leitao
1 sibling, 2 replies; 8+ messages in thread
From: Michael Chan @ 2008-08-04 14:20 UTC (permalink / raw)
To: Stephen Hemminger; +Cc: Randy Dunlap, netdev
On Mon, 2008-08-04 at 10:17 -0700, Stephen Hemminger wrote:
> > In 2.6.27-rc1-git4, I now see this (39 times):
> >
> > BUG: scheduling while atomic: ifconfig/16971/0x00000100
> > Modules linked in: parport_pc lp parport tg3 lpfc cciss ehci_hcd
> ohci_hcd uhci_hcd
> > Pid: 16971, comm: ifconfig Not tainted 2.6.27-rc1-git4 #1
> >
> > Call Trace:
> > [<ffffffff80283db9>] ? page_add_new_anon_rmap+0x20/0x22
> > [<ffffffff802310e9>] __schedule_bug+0x62/0x66
> > [<ffffffff80551146>] schedule+0x99/0x759
> > [<ffffffff8023dc9f>] ? __mod_timer+0xc1/0xd3
> > [<ffffffff8055584a>] ? do_page_fault+0x473/0x7dd
> > [<ffffffff80551ce4>] schedule_timeout+0x8d/0xb4
> > [<ffffffff8023d99e>] ? process_timeout+0x0/0xb
> > [<ffffffff80551cdf>] ? schedule_timeout+0x88/0xb4
> > [<ffffffff80551d24>] schedule_timeout_uninterruptible+0x19/0x1b
> > [<ffffffff8023dcc5>] msleep+0x14/0x1e
> > [<ffffffff80375f2f>] pci_set_power_state+0x1cd/0x292
> > [<ffffffff803739fc>] ? pci_bus_write_config_dword+0x64/0x73
> > [<ffffffffa00651b6>] tg3_set_power_state+0x58/0x884 [tg3]
> > [<ffffffff80552525>] ? __mutex_lock_slowpath+0x1d8/0x1e5
> > [<ffffffffa006b57a>] tg3_open+0x46/0x6cc [tg3]
> > [<ffffffff80552525>] ? __mutex_lock_slowpath+0x1d8/0x1e5
> > [<ffffffff804bdcfe>] dev_open+0x73/0xa8
> > [<ffffffff804bbf5e>] dev_change_flags+0xab/0x167
> > [<ffffffff804f7094>] devinet_ioctl+0x269/0x5da
> > [<ffffffff8026d9da>] ? unlock_page+0x2d/0x32
> > [<ffffffff804f7ca8>] inet_ioctl+0x92/0xaa
> > [<ffffffff804b2046>] sock_ioctl+0x1d1/0x1fb
> > [<ffffffff802a50aa>] vfs_ioctl+0x2a/0x77
> > [<ffffffff802a534c>] do_vfs_ioctl+0x255/0x272
> > [<ffffffff8055584a>] ? do_page_fault+0x473/0x7dd
> > [<ffffffff802a53ab>] sys_ioctl+0x42/0x67
> > [<ffffffff8020beeb>] system_call_fastpath+0x16/0x1b
>
> This is a bug.
>
This was introduced by:
tg3: adapt tg3 to use reworked PCI PM code
Adapt the tg3 driver to use the reworked PCI PM and make it use the
exported PCI PM core functions instead of accessing the PCI PM registers
directly by itself.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original tg3 code, we used udelay() when switching to D0 state
since we were inside tg3_full_lock().
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: 2.6.27-rc1-git4 BUG: sched while atomic
2008-08-04 14:20 ` Michael Chan
@ 2008-08-04 19:13 ` Breno Leitao
2008-08-04 21:40 ` David Miller
1 sibling, 0 replies; 8+ messages in thread
From: Breno Leitao @ 2008-08-04 19:13 UTC (permalink / raw)
To: Michael Chan; +Cc: Stephen Hemminger, Randy Dunlap, netdev
Michael Chan wrote:
> On Mon, 2008-08-04 at 10:17 -0700, Stephen Hemminger wrote:
>>> In 2.6.27-rc1-git4, I now see this (39 times):
>>>
>>> BUG: scheduling while atomic: ifconfig/16971/0x00000100
>>> Modules linked in: parport_pc lp parport tg3 lpfc cciss ehci_hcd
>> ohci_hcd uhci_hcd
>>> Pid: 16971, comm: ifconfig Not tainted 2.6.27-rc1-git4 #1
>>>
>>> Call Trace:
>>> [<ffffffff80283db9>] ? page_add_new_anon_rmap+0x20/0x22
>>> [<ffffffff802310e9>] __schedule_bug+0x62/0x66
>>> [<ffffffff80551146>] schedule+0x99/0x759
>>> [<ffffffff8023dc9f>] ? __mod_timer+0xc1/0xd3
>>> [<ffffffff8055584a>] ? do_page_fault+0x473/0x7dd
>>> [<ffffffff80551ce4>] schedule_timeout+0x8d/0xb4
>>> [<ffffffff8023d99e>] ? process_timeout+0x0/0xb
>>> [<ffffffff80551cdf>] ? schedule_timeout+0x88/0xb4
>>> [<ffffffff80551d24>] schedule_timeout_uninterruptible+0x19/0x1b
>>> [<ffffffff8023dcc5>] msleep+0x14/0x1e
>>> [<ffffffff80375f2f>] pci_set_power_state+0x1cd/0x292
>>> [<ffffffff803739fc>] ? pci_bus_write_config_dword+0x64/0x73
>>> [<ffffffffa00651b6>] tg3_set_power_state+0x58/0x884 [tg3]
>>> [<ffffffff80552525>] ? __mutex_lock_slowpath+0x1d8/0x1e5
>>> [<ffffffffa006b57a>] tg3_open+0x46/0x6cc [tg3]
>>> [<ffffffff80552525>] ? __mutex_lock_slowpath+0x1d8/0x1e5
>>> [<ffffffff804bdcfe>] dev_open+0x73/0xa8
>>> [<ffffffff804bbf5e>] dev_change_flags+0xab/0x167
>>> [<ffffffff804f7094>] devinet_ioctl+0x269/0x5da
>>> [<ffffffff8026d9da>] ? unlock_page+0x2d/0x32
>>> [<ffffffff804f7ca8>] inet_ioctl+0x92/0xaa
>>> [<ffffffff804b2046>] sock_ioctl+0x1d1/0x1fb
>>> [<ffffffff802a50aa>] vfs_ioctl+0x2a/0x77
>>> [<ffffffff802a534c>] do_vfs_ioctl+0x255/0x272
>>> [<ffffffff8055584a>] ? do_page_fault+0x473/0x7dd
>>> [<ffffffff802a53ab>] sys_ioctl+0x42/0x67
>>> [<ffffffff8020beeb>] system_call_fastpath+0x16/0x1b
>> This is a bug.
>>
>
> This was introduced by:
>
> tg3: adapt tg3 to use reworked PCI PM code
>
> Adapt the tg3 driver to use the reworked PCI PM and make it use the
> exported PCI PM core functions instead of accessing the PCI PM registers
> directly by itself.
I just reverted this patch on my tree and the problem doesn't happen anymore.
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: 2.6.27-rc1-git4 BUG: sched while atomic
2008-08-04 14:20 ` Michael Chan
2008-08-04 19:13 ` Breno Leitao
@ 2008-08-04 21:40 ` David Miller
2008-08-05 0:46 ` Matt Carlson
1 sibling, 1 reply; 8+ messages in thread
From: David Miller @ 2008-08-04 21:40 UTC (permalink / raw)
To: mchan; +Cc: shemminger, randy.dunlap, netdev
From: "Michael Chan" <mchan@broadcom.com>
Date: Mon, 04 Aug 2008 07:20:40 -0700
> This was introduced by:
>
> tg3: adapt tg3 to use reworked PCI PM code
>
> Adapt the tg3 driver to use the reworked PCI PM and make it use the
> exported PCI PM core functions instead of accessing the PCI PM registers
> directly by itself.
>
> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
> Signed-off-by: David S. Miller <davem@davemloft.net>
>
> In the original tg3 code, we used udelay() when switching to D0 state
> since we were inside tg3_full_lock().
Right, this change was obviously not tested properly.
I'm likely going to revert unless a really good fix shows up fast.
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: 2.6.27-rc1-git4 BUG: sched while atomic
2008-08-04 21:40 ` David Miller
@ 2008-08-05 0:46 ` Matt Carlson
0 siblings, 0 replies; 8+ messages in thread
From: Matt Carlson @ 2008-08-05 0:46 UTC (permalink / raw)
To: David Miller; +Cc: mchan, shemminger, randy.dunlap, netdev
I'm looking into it right now. Stay tuned.
On Mon, Aug 04, 2008 at 02:40:20PM -0700, David Miller wrote:
> From: "Michael Chan" <mchan@broadcom.com>
> Date: Mon, 04 Aug 2008 07:20:40 -0700
>
> > This was introduced by:
> >
> > tg3: adapt tg3 to use reworked PCI PM code
> >
> > Adapt the tg3 driver to use the reworked PCI PM and make it use the
> > exported PCI PM core functions instead of accessing the PCI PM registers
> > directly by itself.
> >
> > Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
> > Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
> > Signed-off-by: David S. Miller <davem@davemloft.net>
> >
> > In the original tg3 code, we used udelay() when switching to D0 state
> > since we were inside tg3_full_lock().
>
> Right, this change was obviously not tested properly.
>
> I'm likely going to revert unless a really good fix shows up fast.
> --
> To unsubscribe from this list: send the line "unsubscribe netdev" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: 2.6.27-rc1-git4 BUG: sched while atomic
2008-08-04 17:17 ` Stephen Hemminger
2008-08-04 14:20 ` Michael Chan
@ 2008-08-04 18:00 ` Breno Leitao
1 sibling, 0 replies; 8+ messages in thread
From: Breno Leitao @ 2008-08-04 18:00 UTC (permalink / raw)
To: Stephen Hemminger; +Cc: Randy Dunlap, netdev, mchan
I also have an issue like this one using the latest linus's tree (2.6.27-rc1).
My calltrace is a bit different, follows:
BUG: scheduling while atomic: ip/3205/0x00000100
Modules linked in: autofs4 hidp rfcomm l2cap bluetooth sunrpc iptable_filter ip_tables ip6t_REJECT xt_tcpudp ip6table_filter ip6_tables x_tables ipv6 dm_mirror dm_log dm_multipath dm_mod snd_powermac snd_seq_dummy snd_seq_oss snd_seq_midi_event snd_seq snd_seq_device snd_pcm_oss snd_mixer_oss snd_pcm snd_page_alloc snd_timer snd soundcore parport_pc lp parport sg tg3 libphy windfarm_pid windfarm_smu_sat i2c_core shpchp ipr libata sd_mod scsi_mod ext3 jbd uhci_hcd ohci_hcd ehci_hcd
Call Trace:
[c0000001eb98b160] [c00000000001038c] .show_stack+0x70/0x184 (unreliable)
[c0000001eb98b210] [c00000000006b03c] .__schedule_bug+0x6c/0x88
[c0000001eb98b2a0] [c0000000004020c8] .schedule+0xc4/0x8e4
[c0000001eb98b390] [c000000000402f48] .schedule_timeout+0xa8/0xe8
[c0000001eb98b460] [c00000000007f478] .msleep+0x20/0x38
[c0000001eb98b4d0] [c0000000001e5608] .pci_set_power_state+0x274/0x3cc
[c0000001eb98b580] [d0000000004774f0] .tg3_set_power_state+0x80/0xab4 [tg3]
[c0000001eb98b630] [d000000000480fa4] .tg3_open+0x5c/0x96c [tg3]
[c0000001eb98b6f0] [c00000000036d658] .dev_open+0xe4/0x154
[c0000001eb98b770] [c00000000036baf4] .dev_change_flags+0x104/0x204
[c0000001eb98b810] [c0000000003c9e40] .devinet_ioctl+0x2c4/0x758
[c0000001eb98b910] [c0000000003cadf0] .inet_ioctl+0xd8/0x12c
[c0000001eb98b990] [c00000000035cad8] .sock_ioctl+0x2b8/0x310
[c0000001eb98ba30] [c000000000108c74] .vfs_ioctl+0x5c/0xf0
[c0000001eb98bad0] [c000000000109114] .do_vfs_ioctl+0x40c/0x448
[c0000001eb98bb80] [c0000000001091c0] .sys_ioctl+0x70/0xb4
[c0000001eb98bc30] [c00000000013ddb4] .dev_ifsioc+0x1b0/0x3e4
[c0000001eb98bd40] [c00000000013d374] .compat_sys_ioctl+0x3d4/0x468
[c0000001eb98be30] [c0000000000086b4] syscall_exit+0x0/0x40
This error is easily reproducible, just run "ifup ethX; ifdown ethX".
The cable connection is ok, and the device is working fine with older kernels.
It's important to note that I am running on a PPC machine (JS21).
Stephen Hemminger wrote:
> On Mon, 4 Aug 2008 09:48:35 -0700
> Randy Dunlap <randy.dunlap@oracle.com> wrote:
>
>> Usually (e.g., in 2.6.27-rc1 & earlier), I see lots of these messages for
>> some reason:
>>
>> tg3: eth2: Link is up at 1000 Mbps, full duplex.
>> tg3: eth2: Flow control is off for TX and off for RX.
>> tg3: eth3: Link is up at 1000 Mbps, full duplex.
>> tg3: eth3: Flow control is off for TX and off for RX.
>> bnx2: eth1: using MSI
>> bnx2: eth1 NIC SerDes Link is Up, 1000 Mbps full duplex
>> tg3: eth2: Link is up at 1000 Mbps, full duplex.
>> tg3: eth2: Flow control is off for TX and off for RX.
>> tg3: eth3: Link is up at 1000 Mbps, full duplex.
>> tg3: eth3: Flow control is off for TX and off for RX.
>> bnx2: eth1: using MSI
>> bnx2: eth1 NIC SerDes Link is Up, 1000 Mbps full duplex
>> tg3: eth2: Link is up at 1000 Mbps, full duplex.
>> tg3: eth2: Flow control is off for TX and off for RX.
>> tg3: eth3: Link is up at 1000 Mbps, full duplex.
>> tg3: eth3: Flow control is off for TX and off for RX.
>> bnx2: eth1: using MSI
>> bnx2: eth1 NIC SerDes Link is Up, 1000 Mbps full duplex
>> tg3: eth2: Link is up at 1000 Mbps, full duplex.
>> tg3: eth2: Flow control is off for TX and off for RX.
>> tg3: eth3: Link is up at 1000 Mbps, full duplex.
>> tg3: eth3: Flow control is off for TX and off for RX.
>> bnx2: eth1: using MSI
>
> You have a bad cable or broken ethernet switch that is causing
> the link to restart autonegotiation.
>
>> In 2.6.27-rc1-git4, I now see this (39 times):
>>
>> BUG: scheduling while atomic: ifconfig/16971/0x00000100
>> Modules linked in: parport_pc lp parport tg3 lpfc cciss ehci_hcd ohci_hcd uhci_hcd
>> Pid: 16971, comm: ifconfig Not tainted 2.6.27-rc1-git4 #1
>>
>> Call Trace:
>> [<ffffffff80283db9>] ? page_add_new_anon_rmap+0x20/0x22
>> [<ffffffff802310e9>] __schedule_bug+0x62/0x66
>> [<ffffffff80551146>] schedule+0x99/0x759
>> [<ffffffff8023dc9f>] ? __mod_timer+0xc1/0xd3
>> [<ffffffff8055584a>] ? do_page_fault+0x473/0x7dd
>> [<ffffffff80551ce4>] schedule_timeout+0x8d/0xb4
>> [<ffffffff8023d99e>] ? process_timeout+0x0/0xb
>> [<ffffffff80551cdf>] ? schedule_timeout+0x88/0xb4
>> [<ffffffff80551d24>] schedule_timeout_uninterruptible+0x19/0x1b
>> [<ffffffff8023dcc5>] msleep+0x14/0x1e
>> [<ffffffff80375f2f>] pci_set_power_state+0x1cd/0x292
>> [<ffffffff803739fc>] ? pci_bus_write_config_dword+0x64/0x73
>> [<ffffffffa00651b6>] tg3_set_power_state+0x58/0x884 [tg3]
>> [<ffffffff80552525>] ? __mutex_lock_slowpath+0x1d8/0x1e5
>> [<ffffffffa006b57a>] tg3_open+0x46/0x6cc [tg3]
>> [<ffffffff80552525>] ? __mutex_lock_slowpath+0x1d8/0x1e5
>> [<ffffffff804bdcfe>] dev_open+0x73/0xa8
>> [<ffffffff804bbf5e>] dev_change_flags+0xab/0x167
>> [<ffffffff804f7094>] devinet_ioctl+0x269/0x5da
>> [<ffffffff8026d9da>] ? unlock_page+0x2d/0x32
>> [<ffffffff804f7ca8>] inet_ioctl+0x92/0xaa
>> [<ffffffff804b2046>] sock_ioctl+0x1d1/0x1fb
>> [<ffffffff802a50aa>] vfs_ioctl+0x2a/0x77
>> [<ffffffff802a534c>] do_vfs_ioctl+0x255/0x272
>> [<ffffffff8055584a>] ? do_page_fault+0x473/0x7dd
>> [<ffffffff802a53ab>] sys_ioctl+0x42/0x67
>> [<ffffffff8020beeb>] system_call_fastpath+0x16/0x1b
>
> This is a bug.
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: 2.6.27-rc1-git4 BUG: sched while atomic
2008-08-04 16:48 2.6.27-rc1-git4 BUG: sched while atomic Randy Dunlap
2008-08-04 17:17 ` Stephen Hemminger
@ 2008-08-05 12:29 ` Rafael J. Wysocki
1 sibling, 0 replies; 8+ messages in thread
From: Rafael J. Wysocki @ 2008-08-05 12:29 UTC (permalink / raw)
To: Randy Dunlap; +Cc: lkml, netdev, mchan
On Monday, 4 of August 2008, Randy Dunlap wrote:
> Usually (e.g., in 2.6.27-rc1 & earlier), I see lots of these messages for
> some reason:
>
> tg3: eth2: Link is up at 1000 Mbps, full duplex.
> tg3: eth2: Flow control is off for TX and off for RX.
> tg3: eth3: Link is up at 1000 Mbps, full duplex.
> tg3: eth3: Flow control is off for TX and off for RX.
> bnx2: eth1: using MSI
> bnx2: eth1 NIC SerDes Link is Up, 1000 Mbps full duplex
> tg3: eth2: Link is up at 1000 Mbps, full duplex.
> tg3: eth2: Flow control is off for TX and off for RX.
> tg3: eth3: Link is up at 1000 Mbps, full duplex.
> tg3: eth3: Flow control is off for TX and off for RX.
> bnx2: eth1: using MSI
> bnx2: eth1 NIC SerDes Link is Up, 1000 Mbps full duplex
> tg3: eth2: Link is up at 1000 Mbps, full duplex.
> tg3: eth2: Flow control is off for TX and off for RX.
> tg3: eth3: Link is up at 1000 Mbps, full duplex.
> tg3: eth3: Flow control is off for TX and off for RX.
> bnx2: eth1: using MSI
> bnx2: eth1 NIC SerDes Link is Up, 1000 Mbps full duplex
> tg3: eth2: Link is up at 1000 Mbps, full duplex.
> tg3: eth2: Flow control is off for TX and off for RX.
> tg3: eth3: Link is up at 1000 Mbps, full duplex.
> tg3: eth3: Flow control is off for TX and off for RX.
> bnx2: eth1: using MSI
>
>
> In 2.6.27-rc1-git4, I now see this (39 times):
Please try the patch at http://marc.info/?l=linux-netdev&m=121791046925274&w=2
> BUG: scheduling while atomic: ifconfig/16971/0x00000100
> Modules linked in: parport_pc lp parport tg3 lpfc cciss ehci_hcd ohci_hcd uhci_hcd
> Pid: 16971, comm: ifconfig Not tainted 2.6.27-rc1-git4 #1
>
> Call Trace:
> [<ffffffff80283db9>] ? page_add_new_anon_rmap+0x20/0x22
> [<ffffffff802310e9>] __schedule_bug+0x62/0x66
> [<ffffffff80551146>] schedule+0x99/0x759
> [<ffffffff8023dc9f>] ? __mod_timer+0xc1/0xd3
> [<ffffffff8055584a>] ? do_page_fault+0x473/0x7dd
> [<ffffffff80551ce4>] schedule_timeout+0x8d/0xb4
> [<ffffffff8023d99e>] ? process_timeout+0x0/0xb
> [<ffffffff80551cdf>] ? schedule_timeout+0x88/0xb4
> [<ffffffff80551d24>] schedule_timeout_uninterruptible+0x19/0x1b
> [<ffffffff8023dcc5>] msleep+0x14/0x1e
> [<ffffffff80375f2f>] pci_set_power_state+0x1cd/0x292
> [<ffffffff803739fc>] ? pci_bus_write_config_dword+0x64/0x73
> [<ffffffffa00651b6>] tg3_set_power_state+0x58/0x884 [tg3]
> [<ffffffff80552525>] ? __mutex_lock_slowpath+0x1d8/0x1e5
> [<ffffffffa006b57a>] tg3_open+0x46/0x6cc [tg3]
> [<ffffffff80552525>] ? __mutex_lock_slowpath+0x1d8/0x1e5
> [<ffffffff804bdcfe>] dev_open+0x73/0xa8
> [<ffffffff804bbf5e>] dev_change_flags+0xab/0x167
> [<ffffffff804f7094>] devinet_ioctl+0x269/0x5da
> [<ffffffff8026d9da>] ? unlock_page+0x2d/0x32
> [<ffffffff804f7ca8>] inet_ioctl+0x92/0xaa
> [<ffffffff804b2046>] sock_ioctl+0x1d1/0x1fb
> [<ffffffff802a50aa>] vfs_ioctl+0x2a/0x77
> [<ffffffff802a534c>] do_vfs_ioctl+0x255/0x272
> [<ffffffff8055584a>] ? do_page_fault+0x473/0x7dd
> [<ffffffff802a53ab>] sys_ioctl+0x42/0x67
> [<ffffffff8020beeb>] system_call_fastpath+0x16/0x1b
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2008-08-05 12:26 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-08-04 16:48 2.6.27-rc1-git4 BUG: sched while atomic Randy Dunlap
2008-08-04 17:17 ` Stephen Hemminger
2008-08-04 14:20 ` Michael Chan
2008-08-04 19:13 ` Breno Leitao
2008-08-04 21:40 ` David Miller
2008-08-05 0:46 ` Matt Carlson
2008-08-04 18:00 ` Breno Leitao
2008-08-05 12:29 ` Rafael J. Wysocki
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).