netdev.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Ben Hutchings <bhutchings@solarflare.com>
To: David Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org, linux-net-drivers@solarflare.com
Subject: [PATCH 19/20] sfc: Add support for SFN4112F SFP+ reference design
Date: Thu, 29 Jan 2009 19:21:49 +0000	[thread overview]
Message-ID: <1233256909.3656.49.camel@achroite> (raw)
In-Reply-To: <1233256358.3656.9.camel@achroite>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
---
 drivers/net/sfc/boards.c |   62 ++++++++++++++++++++++++++++++++++++++++++++++
 drivers/net/sfc/boards.h |    1 +
 2 files changed, 63 insertions(+), 0 deletions(-)

diff --git a/drivers/net/sfc/boards.c b/drivers/net/sfc/boards.c
index b709878..5182ac5 100644
--- a/drivers/net/sfc/boards.c
+++ b/drivers/net/sfc/boards.c
@@ -226,6 +226,66 @@ static int sfe4002_init(struct efx_nic *efx)
 	return 0;
 }
 
+/*****************************************************************************
+ * Support for the SFN4112F
+ *
+ */
+static u8 sfn4112f_lm87_channel = 0x03; /* use AIN not FAN inputs */
+
+static const u8 sfn4112f_lm87_regs[] = {
+	LM87_IN_LIMITS(0, 0x83, 0x91),		/* 2.5V:  1.8V +/- 5% */
+	LM87_IN_LIMITS(1, 0x51, 0x5a),		/* Vccp1: 1.2V +/- 5% */
+	LM87_IN_LIMITS(2, 0xb6, 0xca),		/* 3.3V:  3.3V +/- 5% */
+	LM87_IN_LIMITS(4, 0xb0, 0xe0),		/* 12V:   11-14V */
+	LM87_IN_LIMITS(5, 0x44, 0x4b),		/* Vccp2: 1.0V +/- 5% */
+	LM87_AIN_LIMITS(1, 0x91, 0xa1),		/* AIN2:  1.5V +/- 5% */
+	LM87_TEMP_INT_LIMITS(10, 60),		/* board */
+	LM87_TEMP_EXT1_LIMITS(10, 70),		/* Falcon */
+	0
+};
+
+static struct i2c_board_info sfn4112f_hwmon_info = {
+	I2C_BOARD_INFO("lm87", 0x2e),
+	.platform_data	= &sfn4112f_lm87_channel,
+	.irq		= -1,
+};
+
+#define SFN4112F_ACT_LED	0
+#define SFN4112F_LINK_LED	1
+
+static void sfn4112f_init_leds(struct efx_nic *efx)
+{
+	xfp_set_led(efx, SFN4112F_ACT_LED,
+		    QUAKE_LED_RXLINK | QUAKE_LED_LINK_ACT);
+	xfp_set_led(efx, SFN4112F_LINK_LED,
+		    QUAKE_LED_RXLINK | QUAKE_LED_LINK_STAT);
+}
+
+static void sfn4112f_set_id_led(struct efx_nic *efx, bool state)
+{
+	xfp_set_led(efx, SFN4112F_LINK_LED,
+		    state ? QUAKE_LED_ON : QUAKE_LED_OFF);
+}
+
+static int sfn4112f_check_hw(struct efx_nic *efx)
+{
+	/* Mask out unused sensors */
+	return efx_check_lm87(efx, ~0x48);
+}
+
+static int sfn4112f_init(struct efx_nic *efx)
+{
+	int rc = efx_init_lm87(efx, &sfn4112f_hwmon_info, sfn4112f_lm87_regs);
+	if (rc)
+		return rc;
+	efx->board_info.monitor = sfn4112f_check_hw;
+	efx->board_info.init_leds = sfn4112f_init_leds;
+	efx->board_info.set_id_led = sfn4112f_set_id_led;
+	efx->board_info.blink = board_blink;
+	efx->board_info.fini = efx_fini_lm87;
+	return 0;
+}
+
 /* This will get expanded as board-specific details get moved out of the
  * PHY drivers. */
 struct efx_board_data {
@@ -241,6 +301,8 @@ static struct efx_board_data board_data[] = {
 	{ EFX_BOARD_SFE4002, "SFE4002", "XFP adapter", sfe4002_init },
 	{ EFX_BOARD_SFN4111T, "SFN4111T", "100/1000/10GBASE-T adapter",
 	  sfn4111t_init },
+	{ EFX_BOARD_SFN4112F, "SFN4112F", "SFP+ adapter",
+	  sfn4112f_init },
 };
 
 void efx_set_board_info(struct efx_nic *efx, u16 revision_info)
diff --git a/drivers/net/sfc/boards.h b/drivers/net/sfc/boards.h
index d93c6c6..44942de 100644
--- a/drivers/net/sfc/boards.h
+++ b/drivers/net/sfc/boards.h
@@ -15,6 +15,7 @@ enum efx_board_type {
 	EFX_BOARD_SFE4001 = 1,
 	EFX_BOARD_SFE4002 = 2,
 	EFX_BOARD_SFN4111T = 0x51,
+	EFX_BOARD_SFN4112F = 0x52,
 };
 
 extern void efx_set_board_info(struct efx_nic *efx, u16 revision_info);

-- 
Ben Hutchings, Senior Software Engineer, Solarflare Communications
Not speaking for my employer; that's the marketing department's job.
They asked us to note that Solarflare product names are trademarked.


  parent reply	other threads:[~2009-01-29 19:21 UTC|newest]

Thread overview: 40+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2009-01-29 19:12 [PATCH 00/20] sfc: Fixes and new PHY support for 2.6.29 Ben Hutchings
2009-01-29 19:15 ` [PATCH 01/20] sfc: SFT9001: Include non-breaking cable diagnostics in online self-tests Ben Hutchings
2009-01-29 19:16 ` [PATCH 02/20] sfc: Fix test for MDIO read failure Ben Hutchings
2009-01-29 19:17 ` [PATCH 03/20] sfc: SFT9001: Enable robust link training Ben Hutchings
2009-01-29 19:23   ` Ben Hutchings
2009-01-29 19:17 ` [PATCH 04/20] sfc: SFX7101: Remove workaround for bad " Ben Hutchings
2009-01-29 19:23   ` Ben Hutchings
2009-01-29 19:17 ` [PATCH 05/20] sfc: SFT9001/SFN4111T: Check PHY boot status during board initialisation Ben Hutchings
2009-01-29 19:17 ` [PATCH 06/20] sfc: SFT9001: Fix speed reporting in 1G PHY loopback Ben Hutchings
2009-01-29 19:18 ` [PATCH 07/20] sfc: SFN4111T: Fix GPIO sharing between I2C and FLASH_CFG_1 Ben Hutchings
2009-01-29 19:19 ` [PATCH 08/20] sfc: Fix post-reset MAC selection Ben Hutchings
2009-01-29 19:19 ` [PATCH 09/20] sfc: Reinitialise the PHY completely in case of a PHY or NIC reset Ben Hutchings
2009-01-29 19:19 ` [PATCH 10/20] sfc: Test for PHYXS faults whenever we cannot test link state bits Ben Hutchings
2009-01-29 19:19 ` [PATCH 11/20] sfc: Update board info for hardware monitor on SFN4111T-R5 and later Ben Hutchings
2009-01-29 19:20 ` [PATCH 12/20] sfc: SFT9001: Always enable XNP exchange on SFT9001 rev B Ben Hutchings
2009-01-29 19:20 ` [PATCH 13/20] sfc: SFX7101/SFT9001: Fix AN advertisements Ben Hutchings
2009-01-29 19:20 ` [PATCH 14/20] sfc: Remove "XFP" from log messages that are not specific to XFP Ben Hutchings
2009-01-29 19:20 ` [PATCH 15/20] sfc: Fix reporting of PHY id Ben Hutchings
2009-01-29 19:21 ` [PATCH 16/20] sfc: Add support for QT2025C PHY Ben Hutchings
2009-01-29 19:21 ` [PATCH 17/20] sfc: Delete unused efx_blinker::led_num field Ben Hutchings
2009-01-29 19:21 ` [PATCH 18/20] sfc: Clean up LED control Ben Hutchings
2009-01-29 19:21 ` Ben Hutchings [this message]
2009-01-29 19:22 ` [PATCH 20/20] sfc: Replace stats_enabled flag with a disable count Ben Hutchings
2009-01-29 23:26 ` [PATCH 00/20] sfc: Fixes and new PHY support for 2.6.29 David Miller
2009-01-30  1:05   ` Ben Hutchings
2009-01-30  1:08     ` David Miller
2009-01-30  3:48       ` [PATCH 01/11] sfc: SFT9001: Enable robust link training Ben Hutchings
2009-01-30 22:09         ` David Miller
2009-01-31  0:04           ` Ben Hutchings
2009-01-31  0:02             ` David Miller
2009-01-30  3:48       ` [PATCH 02/11] sfc: SFX7101: Remove workaround for bad " Ben Hutchings
2009-01-30  3:49       ` [PATCH 03/11] sfc: SFT9001: Fix speed reporting in 1G PHY loopback Ben Hutchings
2009-01-30  3:49       ` [PATCH 04/11] sfc: SFN4111T: Fix GPIO sharing between I2C and FLASH_CFG_1 Ben Hutchings
2009-01-30  3:49       ` [PATCH 05/11] sfc: Fix post-reset MAC selection Ben Hutchings
2009-01-30  3:50       ` [PATCH 06/11] sfc: Reinitialise the PHY completely in case of a PHY or NIC reset Ben Hutchings
2009-01-30  3:51       ` [PATCH 07/11] sfc: Test for PHYXS faults whenever we cannot test link state bits Ben Hutchings
2009-01-30  3:51       ` [PATCH 08/11] sfc: Update board info for hardware monitor on SFN4111T-R5 and later Ben Hutchings
2009-01-30  3:52       ` [PATCH 09/11] sfc: SFT9001: Always enable XNP exchange on SFT9001 rev B Ben Hutchings
2009-01-30  3:59       ` [PATCH 10/11] sfc: SFX7101/SFT9001: Fix AN advertisements Ben Hutchings
2009-01-30  4:00       ` [PATCH 11/11] sfc: Replace stats_enabled flag with a disable count Ben Hutchings

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1233256909.3656.49.camel@achroite \
    --to=bhutchings@solarflare.com \
    --cc=davem@davemloft.net \
    --cc=linux-net-drivers@solarflare.com \
    --cc=netdev@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).