From: Ben Hutchings <bhutchings@solarflare.com>
To: David Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org, linux-net-drivers@solarflare.com
Subject: [PATCH] ethtool: Add reset operation
Date: Mon, 05 Oct 2009 21:59:58 +0100 [thread overview]
Message-ID: <1254776398.2789.7.camel@achroite> (raw)
After updating firmware stored in flash, users may wish to reset the
relevant hardware and start the new firmware immediately. This should
not be completely automatic as it may be disruptive.
A selective reset may also be useful for debugging or diagnostics.
This adds a separate reset operation which takes flags indicating the
components to be reset. Drivers are allowed to reset only a subset of
those requested, and must indicate the actual subset. This allows the
use of generic component masks and some future expansion.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
---
This differs from the previous (RFC) version only in the semantics of
the output value of the reset flags: they should indicate the components
which were *not* reset. This should be slightly less error-prone as it
means implementations do not need to maintain the input and output flags
separately.
Ben.
include/linux/ethtool.h | 32 ++++++++++++++++++++++++++++++++
net/core/ethtool.c | 23 +++++++++++++++++++++++
2 files changed, 55 insertions(+), 0 deletions(-)
diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h
index 15e4eb7..0ef1306 100644
--- a/include/linux/ethtool.h
+++ b/include/linux/ethtool.h
@@ -502,6 +502,7 @@ struct ethtool_ops {
int (*get_rxnfc)(struct net_device *, struct ethtool_rxnfc *, void *);
int (*set_rxnfc)(struct net_device *, struct ethtool_rxnfc *);
int (*flash_device)(struct net_device *, struct ethtool_flash *);
+ int (*reset)(struct net_device *, u32 *);
};
#endif /* __KERNEL__ */
@@ -559,6 +560,7 @@ struct ethtool_ops {
#define ETHTOOL_SRXCLSRLDEL 0x00000031 /* Delete RX classification rule */
#define ETHTOOL_SRXCLSRLINS 0x00000032 /* Insert RX classification rule */
#define ETHTOOL_FLASHDEV 0x00000033 /* Flash firmware to device */
+#define ETHTOOL_RESET 0x00000034 /* Reset hardware */
/* compatibility with older code */
#define SPARC_ETH_GSET ETHTOOL_GSET
@@ -689,4 +691,34 @@ struct ethtool_ops {
#define RX_CLS_FLOW_DISC 0xffffffffffffffffULL
+/* Reset flags */
+/* The reset() operation must clear the flags for the components which
+ * were actually reset. On successful return, the flags indicate the
+ * components which were not reset, either because they do not exist
+ * in the hardware or because they cannot be reset independently. The
+ * driver must never reset any components that were not requested.
+ */
+enum ethtool_reset_flags {
+ /* These flags represent components dedicated to the interface
+ * the command is addressed to. Shift any flag left by
+ * ETH_RESET_SHARED_SHIFT to reset a shared component of the
+ * same type.
+ */
+ ETH_RESET_MGMT = 1 << 0, /* Management processor */
+ ETH_RESET_IRQ = 1 << 1, /* Interrupt requester */
+ ETH_RESET_DMA = 1 << 2, /* DMA engine */
+ ETH_RESET_FILTER = 1 << 3, /* Filtering/flow direction */
+ ETH_RESET_OFFLOAD = 1 << 4, /* Protocol offload */
+ ETH_RESET_MAC = 1 << 5, /* Media access controller */
+ ETH_RESET_PHY = 1 << 6, /* Transceiver/PHY */
+ ETH_RESET_RAM = 1 << 7, /* RAM shared between
+ * multiple components */
+
+ ETH_RESET_DEDICATED = 0x0000ffff, /* All components dedicated to
+ * this interface */
+ ETH_RESET_ALL = 0xffffffff, /* All components used by this
+ * interface, even if shared */
+};
+#define ETH_RESET_SHARED_SHIFT 16
+
#endif /* _LINUX_ETHTOOL_H */
diff --git a/net/core/ethtool.c b/net/core/ethtool.c
index 4c12ddb..6c7429c 100644
--- a/net/core/ethtool.c
+++ b/net/core/ethtool.c
@@ -309,6 +309,26 @@ static int ethtool_get_regs(struct net_device *dev, char __user *useraddr)
return ret;
}
+static int ethtool_reset(struct net_device *dev, char __user *useraddr)
+{
+ struct ethtool_value reset;
+ int ret;
+
+ if (!dev->ethtool_ops->reset)
+ return -EOPNOTSUPP;
+
+ if (copy_from_user(&reset, useraddr, sizeof(reset)))
+ return -EFAULT;
+
+ ret = dev->ethtool_ops->reset(dev, &reset.data);
+ if (ret)
+ return ret;
+
+ if (copy_to_user(useraddr, &reset, sizeof(reset)))
+ return -EFAULT;
+ return 0;
+}
+
static int ethtool_get_wol(struct net_device *dev, char __user *useraddr)
{
struct ethtool_wolinfo wol = { ETHTOOL_GWOL };
@@ -1127,6 +1147,9 @@ int dev_ethtool(struct net *net, struct ifreq *ifr)
case ETHTOOL_FLASHDEV:
rc = ethtool_flash_device(dev, useraddr);
break;
+ case ETHTOOL_RESET:
+ rc = ethtool_reset(dev, useraddr);
+ break;
default:
rc = -EOPNOTSUPP;
}
--
Ben Hutchings, Senior Software Engineer, Solarflare Communications
Not speaking for my employer; that's the marketing department's job.
They asked us to note that Solarflare product names are trademarked.
next reply other threads:[~2009-10-05 21:00 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-10-05 20:59 Ben Hutchings [this message]
2009-10-07 8:29 ` [PATCH] ethtool: Add reset operation David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1254776398.2789.7.camel@achroite \
--to=bhutchings@solarflare.com \
--cc=davem@davemloft.net \
--cc=linux-net-drivers@solarflare.com \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).