Netdev List
 help / color / mirror / Atom feed
From: Ben Hutchings <bhutchings@solarflare.com>
To: David Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org, linux-net-drivers@solarflare.com
Subject: [PATCH net-2.6 2/2] sfc: SFE4002/SFN4112F: Widen temperature and voltage tolerances
Date: Fri, 19 Feb 2010 23:34:03 +0000	[thread overview]
Message-ID: <1266622444.2091.10.camel@achroite.uk.solarflarecom.com> (raw)

The temperature and voltage limits currently set on these boards are
too conservative and will cause the driver to stop the net device
erroneously in some systems.

Based on a review of the chip datasheets and advice from the designer
of these boards:

- Raise the maximum board temperatures to the specified maximum ambient
  temperatures for their PHYs plus the expected temperature bias of the
  board
- Raise the maximum controller temperature to 90 degrees
- Lower the minimum temperatures to 0 degrees
- Widen the voltage tolerances to at least +/- 10%

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
---
 drivers/net/sfc/falcon_boards.c |   45 +++++++++++++++++++++++---------------
 1 files changed, 27 insertions(+), 18 deletions(-)

diff --git a/drivers/net/sfc/falcon_boards.c b/drivers/net/sfc/falcon_boards.c
index bf0b96a..5712fdd 100644
--- a/drivers/net/sfc/falcon_boards.c
+++ b/drivers/net/sfc/falcon_boards.c
@@ -29,6 +29,15 @@
 #define FALCON_BOARD_SFN4111T 0x51
 #define FALCON_BOARD_SFN4112F 0x52
 
+/* Board temperature is about 15°C above ambient when air flow is
+ * limited. */
+#define FALCON_BOARD_TEMP_BIAS	15
+
+/* SFC4000 datasheet says: 'The maximum permitted junction temperature
+ * is 125°C; the thermal design of the environment for the SFC4000
+ * should aim to keep this well below 100°C.' */
+#define FALCON_JUNC_TEMP_MAX	90
+
 /*****************************************************************************
  * Support for LM87 sensor chip used on several boards
  */
@@ -548,16 +557,16 @@ fail_hwmon:
 static u8 sfe4002_lm87_channel = 0x03; /* use AIN not FAN inputs */
 
 static const u8 sfe4002_lm87_regs[] = {
-	LM87_IN_LIMITS(0, 0x83, 0x91),		/* 2.5V:  1.8V +/- 5% */
-	LM87_IN_LIMITS(1, 0x51, 0x5a),		/* Vccp1: 1.2V +/- 5% */
-	LM87_IN_LIMITS(2, 0xb6, 0xca),		/* 3.3V:  3.3V +/- 5% */
-	LM87_IN_LIMITS(3, 0xb0, 0xc9),		/* 5V:    4.6-5.2V */
-	LM87_IN_LIMITS(4, 0xb0, 0xe0),		/* 12V:   11-14V */
-	LM87_IN_LIMITS(5, 0x44, 0x4b),		/* Vccp2: 1.0V +/- 5% */
-	LM87_AIN_LIMITS(0, 0xa0, 0xb2),		/* AIN1:  1.66V +/- 5% */
-	LM87_AIN_LIMITS(1, 0x91, 0xa1),		/* AIN2:  1.5V +/- 5% */
-	LM87_TEMP_INT_LIMITS(10, 60),		/* board */
-	LM87_TEMP_EXT1_LIMITS(10, 70),		/* Falcon */
+	LM87_IN_LIMITS(0, 0x7c, 0x99),		/* 2.5V:  1.8V +/- 10% */
+	LM87_IN_LIMITS(1, 0x4c, 0x5e),		/* Vccp1: 1.2V +/- 10% */
+	LM87_IN_LIMITS(2, 0xac, 0xd4),		/* 3.3V:  3.3V +/- 10% */
+	LM87_IN_LIMITS(3, 0xac, 0xd4),		/* 5V:    5.0V +/- 10% */
+	LM87_IN_LIMITS(4, 0xac, 0xe0),		/* 12V:   10.8-14V */
+	LM87_IN_LIMITS(5, 0x3f, 0x4f),		/* Vccp2: 1.0V +/- 10% */
+	LM87_AIN_LIMITS(0, 0x98, 0xbb),		/* AIN1:  1.66V +/- 10% */
+	LM87_AIN_LIMITS(1, 0x8a, 0xa9),		/* AIN2:  1.5V +/- 10% */
+	LM87_TEMP_INT_LIMITS(0, 80 + FALCON_BOARD_TEMP_BIAS),
+	LM87_TEMP_EXT1_LIMITS(0, FALCON_JUNC_TEMP_MAX),
 	0
 };
 
@@ -619,14 +628,14 @@ static int sfe4002_init(struct efx_nic *efx)
 static u8 sfn4112f_lm87_channel = 0x03; /* use AIN not FAN inputs */
 
 static const u8 sfn4112f_lm87_regs[] = {
-	LM87_IN_LIMITS(0, 0x83, 0x91),		/* 2.5V:  1.8V +/- 5% */
-	LM87_IN_LIMITS(1, 0x51, 0x5a),		/* Vccp1: 1.2V +/- 5% */
-	LM87_IN_LIMITS(2, 0xb6, 0xca),		/* 3.3V:  3.3V +/- 5% */
-	LM87_IN_LIMITS(4, 0xb0, 0xe0),		/* 12V:   11-14V */
-	LM87_IN_LIMITS(5, 0x44, 0x4b),		/* Vccp2: 1.0V +/- 5% */
-	LM87_AIN_LIMITS(1, 0x91, 0xa1),		/* AIN2:  1.5V +/- 5% */
-	LM87_TEMP_INT_LIMITS(10, 60),		/* board */
-	LM87_TEMP_EXT1_LIMITS(10, 70),		/* Falcon */
+	LM87_IN_LIMITS(0, 0x7c, 0x99),		/* 2.5V:  1.8V +/- 10% */
+	LM87_IN_LIMITS(1, 0x4c, 0x5e),		/* Vccp1: 1.2V +/- 10% */
+	LM87_IN_LIMITS(2, 0xac, 0xd4),		/* 3.3V:  3.3V +/- 10% */
+	LM87_IN_LIMITS(4, 0xac, 0xe0),		/* 12V:   10.8-14V */
+	LM87_IN_LIMITS(5, 0x3f, 0x4f),		/* Vccp2: 1.0V +/- 10% */
+	LM87_AIN_LIMITS(1, 0x8a, 0xa9),		/* AIN2:  1.5V +/- 10% */
+	LM87_TEMP_INT_LIMITS(0, 60 + FALCON_BOARD_TEMP_BIAS),
+	LM87_TEMP_EXT1_LIMITS(0, FALCON_JUNC_TEMP_MAX),
 	0
 };
 
-- 
1.6.2.5

-- 
Ben Hutchings, Senior Software Engineer, Solarflare Communications
Not speaking for my employer; that's the marketing department's job.
They asked us to note that Solarflare product names are trademarked.


             reply	other threads:[~2010-02-19 23:34 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2010-02-19 23:34 Ben Hutchings [this message]
2010-02-20  1:03 ` [PATCH net-2.6 2/2] sfc: SFE4002/SFN4112F: Widen temperature and voltage tolerances David Miller

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1266622444.2091.10.camel@achroite.uk.solarflarecom.com \
    --to=bhutchings@solarflare.com \
    --cc=davem@davemloft.net \
    --cc=linux-net-drivers@solarflare.com \
    --cc=netdev@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox