From: Stefani Seibold <stefani@seibold.net>
To: linux-kernel <linux-kernel@vger.kernel.org>, netdev@vger.kernel.org
Subject: [PATCH] fix PHY polling system blocking
Date: Sat, 13 Mar 2010 13:53:10 +0100 [thread overview]
Message-ID: <1268484790.6339.37.camel@wall-e> (raw)
This patch fix the PHY poller, which can block the whole system. PHY
access are normaly not very fast, since there are serial attached.
For PHY chips without interrupts, the status of the ethernet will be
polled every 2 sec. The poll function will read some register of the MII
PHY. The time between the sending the MII_READ_COMMAND and receiving the
result could be very long (>100us).
For example:
On a Freescale PPC 834x this result in a delay of 450 us due the slow
communication with the PHY chip. The time between the sending the
MII_READ_COMMAND and receiving the result is more the 100 us on this
controller.
The patch modifies the poller a lit bit. Only a link status state change
will result in a successive detection of the connection type. The poll
cycle on the other hand will be increased to one every seconds.
All in all this patch will prevent a blocking of f.e nearly 400 us every
two seconds of the whole system on a PPC 834x.
There is not real drawback, only the detection of a connection type
change without unplugging the cable will not work. But this is more an
esoteric use case.
The patch is against kernel 2.6.33. Please merge it.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
---
phy.c | 5 ++---
phy_device.c | 11 ++++++++---
2 files changed, 10 insertions(+), 6 deletions(-)
diff -u -N -r -p linux-2.6.33.orig/drivers/net/phy/phy.c linux-2.6.33/drivers/net/phy/phy.c
--- linux-2.6.33.orig/drivers/net/phy/phy.c 2010-02-24 19:52:17.000000000 +0100
+++ linux-2.6.33/drivers/net/phy/phy.c 2010-02-28 22:53:14.725464101 +0100
@@ -871,9 +871,8 @@ void phy_state_machine(struct work_struc
case PHY_RUNNING:
/* Only register a CHANGE if we are
* polling */
- if (PHY_POLL == phydev->irq)
- phydev->state = PHY_CHANGELINK;
- break;
+ if (PHY_POLL != phydev->irq)
+ break;
case PHY_CHANGELINK:
err = phy_read_status(phydev);
diff -u -N -r -p linux-2.6.33.orig/drivers/net/phy/phy_device.c linux-2.6.33/drivers/net/phy/phy_device.c
--- linux-2.6.33.orig/drivers/net/phy/phy_device.c 2010-02-24 19:52:17.000000000 +0100
+++ linux-2.6.33/drivers/net/phy/phy_device.c 2010-02-28 22:53:14.726464145 +0100
@@ -161,7 +161,7 @@ struct phy_device* phy_device_create(str
dev->speed = 0;
dev->duplex = -1;
dev->pause = dev->asym_pause = 0;
- dev->link = 1;
+ dev->link = 0;
dev->interface = PHY_INTERFACE_MODE_GMII;
dev->autoneg = AUTONEG_ENABLE;
@@ -694,10 +694,15 @@ int genphy_update_link(struct phy_device
if (status < 0)
return status;
- if ((status & BMSR_LSTATUS) == 0)
+ if ((status & BMSR_LSTATUS) == 0) {
+ if (phydev->link == 0)
+ return 1;
phydev->link = 0;
- else
+ } else {
+ if (phydev->link == 1)
+ return 1;
phydev->link = 1;
+ }
return 0;
}
next reply other threads:[~2010-03-13 12:53 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-03-13 12:53 Stefani Seibold [this message]
2010-03-13 20:12 ` [PATCH] fix PHY polling system blocking David Miller
-- strict thread matches above, loose matches on Subject: below --
2010-03-06 16:50 Stefani Seibold
2010-03-12 22:42 ` Andrew Morton
2010-03-13 11:54 ` Stefani Seibold
2010-03-13 20:10 ` David Miller
2010-03-21 21:54 ` Stefani Seibold
2010-03-22 0:56 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1268484790.6339.37.camel@wall-e \
--to=stefani@seibold.net \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).