Re: E100 RX ring buffers continued...

[Walt Holman <walt@holmansrus.com>]

----- "Krzysztof Halasa" <khc@pm.waw.pl> wrote:

> David Miller <davem@davemloft.net> writes:
> 
> > I think going down the road of trying to use the flexible mode is a
> > dead end.  I doubt any other OS driver is using it, and that means
> > that there are likely many other errata hiding in the bushes which
> you
> > will unearth by trying to use this new descriptor mode.  And it
> won't
> > show up when you test it, it will show up when some random person
> in
> > some remote data center somewhere updates their kernel, and they
> won't
> > send us a bug report, they'll replace their card or downgrade their
> > kernel instead.
> 
> Well, I'm afraid it's a possible scenario. I won't touch the flexible
> mode unless Intel folks tell me it's safe.
> OTOH it seems it was used by less common software, at least in the
> 82557-9 times. Not sure about Windows driver.
> (It seems the simplified mode was meant for Linux-alike "1 buffer per
> packet" approach while the flexible mode was to support systems using
> mbuf-like structures).
> 
> > Just make the driver use consistent buffers for RX, and when
> packets
> > arrive an SKB is allocated and the packet data is copied into the
> SKB
> >>From the consistent buffer.
> 
> That would be a performance hit, wouldn't it? Especially in older
> machines, where e100 was typically installed. I think it should be
> the
> last resort.
> 
> > And for 2.6.31-rcX we probably have to simply revert your change.
> 
> Unfortunately it seems that reverting will not fix operation
> completely
> on a system with swiotlb (checking the descriptor status isn't the
> only
> racy operation which depends on the cache behaviour, though it's the
> most frequent). And it will break all non-coherent archs again, they
> will either need to use the patch or still stick to (already removed)
> eepro100.c
> 
> I looked at the eepro100.c sources. It uses BIDIR mapping the same
> way
> as e100.c does, but then syncs using FROM_DEVICE/TO_DEVICE instead of
> e100's always-BIDIR. I think the same in e100.c would work on all
> platforms (though still violating the DMA API a bit). Perhaps we
> should
> do that instead?
> 
> Walt, can you check if 2.6.30.5 with the following patch applied
> still
> breaks e100 with the 6 GB of RAM, please? TIA.
> (This patch makes swiotlb aware that the CPU didn't alter the buffer,
> though I don't know if swiotlb will use this info).
> 
> diff --git a/drivers/net/e100.c b/drivers/net/e100.c
> index 014dfb6..53e8252 100644
> --- a/drivers/net/e100.c
> +++ b/drivers/net/e100.c
> @@ -1764,7 +1764,7 @@ static int e100_rx_indicate(struct nic *nic,
> struct rx *rx,
>  				nic->ru_running = RU_SUSPENDED;
>  		pci_dma_sync_single_for_device(nic->pdev, rx->dma_addr,
>  					       sizeof(struct rfd),
> -					       PCI_DMA_BIDIRECTIONAL);
> +					       PCI_DMA_FROMDEVICE);
>  		return -ENODATA;
>  	}
>  
> -- 
> Krzysztof Halasa

Krzystof,

I've tested this under 2.6.31-rc7 (which was also broken to begin with) and this appears to have fixed it.  It's a fairly limited test at this point, as I've just been downloading a large file for the past 15 mins. or so, but this was normally enough to have multiple stoppages.  Do you still need 2.6.30.5 tested as well?

-Walt