From: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To: davem@davemloft.net
Cc: John Fastabend <john.r.fastabend@intel.com>,
netdev@vger.kernel.org, gospo@redhat.com, bphilips@novell.com,
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Subject: [net-next-2.6 10/16] ixgbe: DCB, do not reset on CEE pg changes
Date: Tue, 8 Feb 2011 04:29:21 -0800 [thread overview]
Message-ID: <1297168167-15755-11-git-send-email-jeffrey.t.kirsher@intel.com> (raw)
In-Reply-To: <1297168167-15755-1-git-send-email-jeffrey.t.kirsher@intel.com>
From: John Fastabend <john.r.fastabend@intel.com>
The 82599 and 82598 devices do not require hardware resets to
configure CEE pg settings. This patch changes DCB configuration
to set the CEE pg values directly from the dcbnl ops routine.
This reduces the number of resets seen on the wire and allows
LLDP to reach a steady state faster.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ixgbe/ixgbe_dcb.h | 4 +++
drivers/net/ixgbe/ixgbe_dcb_nl.c | 48 +++++++++++++++++++++++++++----------
2 files changed, 39 insertions(+), 13 deletions(-)
diff --git a/drivers/net/ixgbe/ixgbe_dcb.h b/drivers/net/ixgbe/ixgbe_dcb.h
index 4e4a641..e593511 100644
--- a/drivers/net/ixgbe/ixgbe_dcb.h
+++ b/drivers/net/ixgbe/ixgbe_dcb.h
@@ -148,6 +148,10 @@ struct ixgbe_dcb_config {
/* DCB driver APIs */
void ixgbe_dcb_unpack_pfc(struct ixgbe_dcb_config *cfg, u8 *pfc_en);
+void ixgbe_dcb_unpack_refill(struct ixgbe_dcb_config *, int, u16 *);
+void ixgbe_dcb_unpack_max(struct ixgbe_dcb_config *, u16 *);
+void ixgbe_dcb_unpack_bwgid(struct ixgbe_dcb_config *, int, u8 *);
+void ixgbe_dcb_unpack_prio(struct ixgbe_dcb_config *, int, u8 *);
/* DCB credits calculation */
s32 ixgbe_ieee_credits(__u8 *bw, __u16 *refill, __u16 *max, int max_frame);
diff --git a/drivers/net/ixgbe/ixgbe_dcb_nl.c b/drivers/net/ixgbe/ixgbe_dcb_nl.c
index e75a3c9..b3a8d24 100644
--- a/drivers/net/ixgbe/ixgbe_dcb_nl.c
+++ b/drivers/net/ixgbe/ixgbe_dcb_nl.c
@@ -225,10 +225,8 @@ static void ixgbe_dcbnl_set_pg_tc_cfg_tx(struct net_device *netdev, int tc,
(adapter->temp_dcb_cfg.tc_config[tc].path[0].bwg_percent !=
adapter->dcb_cfg.tc_config[tc].path[0].bwg_percent) ||
(adapter->temp_dcb_cfg.tc_config[tc].path[0].up_to_tc_bitmap !=
- adapter->dcb_cfg.tc_config[tc].path[0].up_to_tc_bitmap)) {
+ adapter->dcb_cfg.tc_config[tc].path[0].up_to_tc_bitmap))
adapter->dcb_set_bitmap |= BIT_PG_TX;
- adapter->dcb_set_bitmap |= BIT_RESETLINK;
- }
}
static void ixgbe_dcbnl_set_pg_bwg_cfg_tx(struct net_device *netdev, int bwg_id,
@@ -239,10 +237,8 @@ static void ixgbe_dcbnl_set_pg_bwg_cfg_tx(struct net_device *netdev, int bwg_id,
adapter->temp_dcb_cfg.bw_percentage[0][bwg_id] = bw_pct;
if (adapter->temp_dcb_cfg.bw_percentage[0][bwg_id] !=
- adapter->dcb_cfg.bw_percentage[0][bwg_id]) {
+ adapter->dcb_cfg.bw_percentage[0][bwg_id])
adapter->dcb_set_bitmap |= BIT_PG_TX;
- adapter->dcb_set_bitmap |= BIT_RESETLINK;
- }
}
static void ixgbe_dcbnl_set_pg_tc_cfg_rx(struct net_device *netdev, int tc,
@@ -269,10 +265,8 @@ static void ixgbe_dcbnl_set_pg_tc_cfg_rx(struct net_device *netdev, int tc,
(adapter->temp_dcb_cfg.tc_config[tc].path[1].bwg_percent !=
adapter->dcb_cfg.tc_config[tc].path[1].bwg_percent) ||
(adapter->temp_dcb_cfg.tc_config[tc].path[1].up_to_tc_bitmap !=
- adapter->dcb_cfg.tc_config[tc].path[1].up_to_tc_bitmap)) {
+ adapter->dcb_cfg.tc_config[tc].path[1].up_to_tc_bitmap))
adapter->dcb_set_bitmap |= BIT_PG_RX;
- adapter->dcb_set_bitmap |= BIT_RESETLINK;
- }
}
static void ixgbe_dcbnl_set_pg_bwg_cfg_rx(struct net_device *netdev, int bwg_id,
@@ -283,10 +277,8 @@ static void ixgbe_dcbnl_set_pg_bwg_cfg_rx(struct net_device *netdev, int bwg_id,
adapter->temp_dcb_cfg.bw_percentage[1][bwg_id] = bw_pct;
if (adapter->temp_dcb_cfg.bw_percentage[1][bwg_id] !=
- adapter->dcb_cfg.bw_percentage[1][bwg_id]) {
+ adapter->dcb_cfg.bw_percentage[1][bwg_id])
adapter->dcb_set_bitmap |= BIT_PG_RX;
- adapter->dcb_set_bitmap |= BIT_RESETLINK;
- }
}
static void ixgbe_dcbnl_get_pg_tc_cfg_tx(struct net_device *netdev, int tc,
@@ -421,7 +413,9 @@ static u8 ixgbe_dcbnl_set_all(struct net_device *netdev)
ixgbe_up(adapter);
}
ret = DCB_HW_CHG_RST;
- } else if (adapter->dcb_set_bitmap & BIT_PFC) {
+ }
+
+ if (adapter->dcb_set_bitmap & BIT_PFC) {
u8 pfc_en;
ixgbe_dcb_unpack_pfc(&adapter->dcb_cfg, &pfc_en);
@@ -431,6 +425,34 @@ static u8 ixgbe_dcbnl_set_all(struct net_device *netdev)
ixgbe_dcb_config_pfc_82599(&adapter->hw, pfc_en);
ret = DCB_HW_CHG;
}
+
+ if (adapter->dcb_set_bitmap & (BIT_PG_TX|BIT_PG_RX)) {
+ u16 refill[MAX_TRAFFIC_CLASS], max[MAX_TRAFFIC_CLASS];
+ u8 bwg_id[MAX_TRAFFIC_CLASS], prio_type[MAX_TRAFFIC_CLASS];
+ int max_frame = adapter->netdev->mtu + ETH_HLEN + ETH_FCS_LEN;
+
+#ifdef CONFIG_FCOE
+ if (adapter->netdev->features & NETIF_F_FCOE_MTU)
+ max_frame = max(max_frame, IXGBE_FCOE_JUMBO_FRAME_SIZE);
+#endif
+
+ ixgbe_dcb_calculate_tc_credits(&adapter->hw, &adapter->dcb_cfg,
+ max_frame, DCB_TX_CONFIG);
+ ixgbe_dcb_calculate_tc_credits(&adapter->hw, &adapter->dcb_cfg,
+ max_frame, DCB_RX_CONFIG);
+
+ ixgbe_dcb_unpack_refill(&adapter->dcb_cfg,
+ DCB_TX_CONFIG, refill);
+ ixgbe_dcb_unpack_max(&adapter->dcb_cfg, max);
+ ixgbe_dcb_unpack_bwgid(&adapter->dcb_cfg,
+ DCB_TX_CONFIG, bwg_id);
+ ixgbe_dcb_unpack_prio(&adapter->dcb_cfg,
+ DCB_TX_CONFIG, prio_type);
+
+ ixgbe_dcb_hw_ets_config(&adapter->hw, refill, max,
+ bwg_id, prio_type);
+ }
+
if (adapter->dcb_cfg.pfc_mode_enable)
adapter->hw.fc.current_mode = ixgbe_fc_pfc;
--
1.7.4
next prev parent reply other threads:[~2011-02-08 12:29 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-02-08 12:29 [net-next-2.6 00/16][pull request] Intel Wired LAN Driver Updates Jeff Kirsher
2011-02-08 12:29 ` [net-next-2.6 01/16] e1000e: replace unbounded sprintf with snprintf Jeff Kirsher
2011-02-08 12:29 ` [net-next-2.6 02/16] e1000e: use correct pointer when memcpy'ing a 2-dimensional array Jeff Kirsher
2011-02-08 12:29 ` [net-next-2.6 03/16] e1000e: do not wakeup Tx queue until ready Jeff Kirsher
2011-02-08 20:21 ` David Miller
2011-02-08 20:52 ` Allan, Bruce W
2011-02-08 12:29 ` [net-next-2.6 04/16] e1000e: return appropriate errors for 'ethtool -r' Jeff Kirsher
2011-02-08 12:29 ` [net-next-2.6 05/16] igb: Enable PF side of SR-IOV support for i350 devices Jeff Kirsher
2011-02-08 12:29 ` [net-next-2.6 06/16] ixgbe: DCB, only reprogram HW if the FCoE priority is changed Jeff Kirsher
2011-02-08 12:29 ` [net-next-2.6 07/16] ixgbe: DCB, remove round robin mode on 82598 devices Jeff Kirsher
2011-02-08 12:29 ` [net-next-2.6 08/16] ixgbe: DCB, abstract out dcb_config from DCB hardware configuration Jeff Kirsher
2011-02-08 12:29 ` [net-next-2.6 09/16] ixgbe: DCB, implement 802.1Qaz routines Jeff Kirsher
2011-02-08 12:29 ` Jeff Kirsher [this message]
2011-02-08 12:29 ` [net-next-2.6 11/16] ixgbe: DCB, remove RESET bit it is no longer needed Jeff Kirsher
2011-02-08 12:29 ` [net-next-2.6 12/16] ixgbe: dcb, use hardware independent routines Jeff Kirsher
2011-02-08 12:29 ` [net-next-2.6 13/16] ixgbe: fix namespace issue with ixgbe_dcb_txq_to_tc Jeff Kirsher
2011-02-08 12:29 ` [net-next-2.6 14/16] ixgbe: cleanup namespace complaint by removing little used function Jeff Kirsher
2011-02-08 12:29 ` [net-next-2.6 15/16] ixgbe: cleanup ixgbe_init_mbx_params_pf namespace issue Jeff Kirsher
2011-02-08 12:29 ` [net-next-2.6 16/16] ixgbe: Adding 100MB FULL support in ethtool Jeff Kirsher
2011-02-11 15:55 ` [net-next-2.6 00/16][pull request] Intel Wired LAN Driver Updates Jeff Kirsher
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1297168167-15755-11-git-send-email-jeffrey.t.kirsher@intel.com \
--to=jeffrey.t.kirsher@intel.com \
--cc=bphilips@novell.com \
--cc=davem@davemloft.net \
--cc=gospo@redhat.com \
--cc=john.r.fastabend@intel.com \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).