From mboxrd@z Thu Jan 1 00:00:00 1970 From: Mark Einon Subject: [PATCH] mii: Remove references to DP83840 PHY in mii.h Date: Wed, 31 Aug 2011 16:35:28 +0100 Message-ID: <1314804928-7353-1-git-send-email-mark.einon@gmail.com> Cc: davem@davemloft.net, Mark Einon To: netdev@vger.kernel.org Return-path: Received: from mail-wy0-f174.google.com ([74.125.82.174]:38233 "EHLO mail-wy0-f174.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1755737Ab1HaPgr (ORCPT ); Wed, 31 Aug 2011 11:36:47 -0400 Received: by wyh22 with SMTP id 22so244587wyh.19 for ; Wed, 31 Aug 2011 08:36:46 -0700 (PDT) Sender: netdev-owner@vger.kernel.org List-ID: There are references to this PHY chip in the generic mii.h header, so removing them. Signed-off-by: Mark Einon --- include/linux/mii.h | 12 ++++++------ 1 files changed, 6 insertions(+), 6 deletions(-) diff --git a/include/linux/mii.h b/include/linux/mii.h index 103113a..4c3cfb5 100644 --- a/include/linux/mii.h +++ b/include/linux/mii.h @@ -40,12 +40,12 @@ #define BMCR_CTST 0x0080 /* Collision test */ #define BMCR_FULLDPLX 0x0100 /* Full duplex */ #define BMCR_ANRESTART 0x0200 /* Auto negotiation restart */ -#define BMCR_ISOLATE 0x0400 /* Disconnect DP83840 from MII */ -#define BMCR_PDOWN 0x0800 /* Powerdown the DP83840 */ +#define BMCR_ISOLATE 0x0400 /* Disconnect PHY from MII */ +#define BMCR_PDOWN 0x0800 /* Powerdown */ #define BMCR_ANENABLE 0x1000 /* Enable auto negotiation */ #define BMCR_SPEED100 0x2000 /* Select 100Mbps */ #define BMCR_LOOPBACK 0x4000 /* TXD loopback bits */ -#define BMCR_RESET 0x8000 /* Reset the DP83840 */ +#define BMCR_RESET 0x8000 /* Reset */ /* Basic mode status register. */ #define BMSR_ERCAP 0x0001 /* Ext-reg capability */ @@ -55,9 +55,9 @@ #define BMSR_RFAULT 0x0010 /* Remote fault detected */ #define BMSR_ANEGCOMPLETE 0x0020 /* Auto-negotiation complete */ #define BMSR_RESV 0x00c0 /* Unused... */ -#define BMSR_ESTATEN 0x0100 /* Extended Status in R15 */ -#define BMSR_100HALF2 0x0200 /* Can do 100BASE-T2 HDX */ -#define BMSR_100FULL2 0x0400 /* Can do 100BASE-T2 FDX */ +#define BMSR_ESTATEN 0x0100 /* Extended Status in R15 */ +#define BMSR_100HALF2 0x0200 /* Can do 100BASE-T2 HDX */ +#define BMSR_100FULL2 0x0400 /* Can do 100BASE-T2 FDX */ #define BMSR_10HALF 0x0800 /* Can do 10mbps, half-duplex */ #define BMSR_10FULL 0x1000 /* Can do 10mbps, full-duplex */ #define BMSR_100HALF 0x2000 /* Can do 100mbps, half-duplex */ -- 1.7.6