From: Ben Hutchings <bhutchings@solarflare.com>
To: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: davem@davemloft.net, Greg Rose <gregory.v.rose@intel.com>,
netdev@vger.kernel.org, gospo@redhat.com
Subject: Re: [net-next 05/10] if_link: Add additional parameter to IFLA_VF_INFO for spoof checking
Date: Sat, 24 Sep 2011 17:40:56 +0100 [thread overview]
Message-ID: <1316882459.4122.83.camel@deadeye> (raw)
In-Reply-To: <1316855863-6091-6-git-send-email-jeffrey.t.kirsher@intel.com>
On Sat, 2011-09-24 at 02:17 -0700, Jeff Kirsher wrote:
> From: Greg Rose <gregory.v.rose@intel.com>
>
> Add configuration setting for drivers to turn spoof checking on or off
> for discrete VFs.
>
> Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
> ---
> include/linux/if_link.h | 7 +++++++
> include/linux/netdevice.h | 3 +++
> net/core/rtnetlink.c | 25 ++++++++++++++++++++++---
> 3 files changed, 32 insertions(+), 3 deletions(-)
>
> diff --git a/include/linux/if_link.h b/include/linux/if_link.h
> index 0ee969a..8bd6d6d 100644
> --- a/include/linux/if_link.h
> +++ b/include/linux/if_link.h
> @@ -279,6 +279,7 @@ enum {
> IFLA_VF_MAC, /* Hardware queue specific attributes */
> IFLA_VF_VLAN,
> IFLA_VF_TX_RATE, /* TX Bandwidth Allocation */
> + IFLA_VF_SPOOFCHK, /* Spoof Checking on/off switch */
> __IFLA_VF_MAX,
> };
>
> @@ -300,12 +301,18 @@ struct ifla_vf_tx_rate {
> __u32 rate; /* Max TX bandwidth in Mbps, 0 disables throttling */
> };
>
> +struct ifla_vf_spoofchk {
> + __u32 vf;
> + __u32 setting;
> +};
> +
> struct ifla_vf_info {
> __u32 vf;
> __u8 mac[32];
> __u32 vlan;
> __u32 qos;
> __u32 tx_rate;
> + __u32 spoofchk;
> };
Not something you need to change now, but shouldn't this last struct
definition be #ifdef __KERNEL__?
> /* VF ports management section
> diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h
> index 43b3298..a2951a0 100644
> --- a/include/linux/netdevice.h
> +++ b/include/linux/netdevice.h
> @@ -781,6 +781,7 @@ struct netdev_tc_txq {
> * int (*ndo_set_vf_mac)(struct net_device *dev, int vf, u8* mac);
> * int (*ndo_set_vf_vlan)(struct net_device *dev, int vf, u16 vlan, u8 qos);
> * int (*ndo_set_vf_tx_rate)(struct net_device *dev, int vf, int rate);
> + * int (*ndo_set_vf_spoofchk)(struct net_device *dev, int vf, u8 setting);
> * int (*ndo_get_vf_config)(struct net_device *dev,
> * int vf, struct ifla_vf_info *ivf);
> * int (*ndo_set_vf_port)(struct net_device *dev, int vf,
> @@ -900,6 +901,8 @@ struct net_device_ops {
> int queue, u16 vlan, u8 qos);
> int (*ndo_set_vf_tx_rate)(struct net_device *dev,
> int vf, int rate);
> + int (*ndo_set_vf_spoofchk)(struct net_device *dev,
> + int vf, u8 setting);
Why u8 and not bool?
> int (*ndo_get_vf_config)(struct net_device *dev,
> int vf,
> struct ifla_vf_info *ivf);
> diff --git a/net/core/rtnetlink.c b/net/core/rtnetlink.c
> index 39f8dd6..6535810 100644
> --- a/net/core/rtnetlink.c
> +++ b/net/core/rtnetlink.c
> @@ -731,7 +731,8 @@ static inline int rtnl_vfinfo_size(const struct net_device *dev)
> size += num_vfs *
> (nla_total_size(sizeof(struct ifla_vf_mac)) +
> nla_total_size(sizeof(struct ifla_vf_vlan)) +
> - nla_total_size(sizeof(struct ifla_vf_tx_rate)));
> + nla_total_size(sizeof(struct ifla_vf_tx_rate)) +
> + nla_total_size(sizeof(struct ifla_vf_spoofchk)));
> return size;
> } else
> return 0;
> @@ -954,13 +955,19 @@ static int rtnl_fill_ifinfo(struct sk_buff *skb, struct net_device *dev,
> struct ifla_vf_mac vf_mac;
> struct ifla_vf_vlan vf_vlan;
> struct ifla_vf_tx_rate vf_tx_rate;
> + struct ifla_vf_spoofchk vf_spoofchk;
> if (dev->netdev_ops->ndo_get_vf_config(dev, i, &ivi))
> break;
> - vf_mac.vf = vf_vlan.vf = vf_tx_rate.vf = ivi.vf;
> + vf_mac.vf =
> + vf_vlan.vf =
> + vf_tx_rate.vf =
> + vf_spoofchk.vf = ivi.vf;
> +
[...]
The continuation lines should be indented. Or you could just write the
assignments as multiple statements.
Ben.
--
Ben Hutchings, Staff Engineer, Solarflare
Not speaking for my employer; that's the marketing department's job.
They asked us to note that Solarflare product names are trademarked.
next prev parent reply other threads:[~2011-09-24 16:41 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-09-24 9:17 [net-next 00/10][pull request] Intel Wired LAN Drivers Update Jeff Kirsher
2011-09-24 9:17 ` [net-next 01/10] e1000: don't enable dma receives until after dma address has been setup Jeff Kirsher
2011-09-24 9:17 ` [net-next 02/10] ixgbevf: Fix broken trunk vlan Jeff Kirsher
2011-09-24 16:33 ` Jesse Gross
2011-09-25 5:47 ` Jeff Kirsher
2011-09-26 15:57 ` Rose, Gregory V
2011-09-26 23:08 ` Jesse Gross
2011-09-26 23:24 ` Rose, Gregory V
2011-09-27 0:54 ` Jesse Gross
2011-09-27 16:39 ` Rose, Gregory V
2011-09-27 16:49 ` Jesse Gross
2011-09-24 9:17 ` [net-next 03/10] ixgbe: Cleanup q_vector interrupt throttle rate logic Jeff Kirsher
2011-09-24 9:17 ` [net-next 04/10] ixgbe: disable LLI for FCoE Jeff Kirsher
2011-09-24 9:17 ` [net-next 05/10] if_link: Add additional parameter to IFLA_VF_INFO for spoof checking Jeff Kirsher
2011-09-24 16:40 ` Ben Hutchings [this message]
2011-09-25 5:54 ` Jeff Kirsher
2011-09-26 16:06 ` Rose, Gregory V
2011-09-25 17:22 ` Stephen Hemminger
2011-09-25 20:06 ` Ben Hutchings
2011-09-26 16:14 ` Stephen Hemminger
2011-09-26 16:32 ` Rose, Gregory V
2011-09-26 16:37 ` Stephen Hemminger
2011-09-26 16:18 ` Rose, Gregory V
2011-09-26 16:21 ` Stephen Hemminger
2011-09-26 16:57 ` Rose, Gregory V
2011-09-24 9:17 ` [net-next 06/10] ixgbe: Add new netdev op to turn spoof checking on or off per VF Jeff Kirsher
2011-09-24 9:17 ` [net-next 07/10] ixgbe: update {P}FC thresholds to account for X540 and loopback Jeff Kirsher
2011-09-24 9:17 ` [net-next 08/10] ixgbe add thermal sensor support for x540 hardware Jeff Kirsher
2011-09-24 9:17 ` [net-next 09/10] ixgbe: cleanup ixgbe_setup_gpie() for X540 Jeff Kirsher
2011-09-24 9:17 ` [net-next 10/10] ixgbe: add ECC warning for legacy interrupts Jeff Kirsher
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1316882459.4122.83.camel@deadeye \
--to=bhutchings@solarflare.com \
--cc=davem@davemloft.net \
--cc=gospo@redhat.com \
--cc=gregory.v.rose@intel.com \
--cc=jeffrey.t.kirsher@intel.com \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox