From mboxrd@z Thu Jan 1 00:00:00 1970 From: Giuseppe CAVALLARO Subject: [net-next 1/7] stmmac: Stop advertising 1000Base capabilties for non GMII iface (V3). Date: Tue, 18 Oct 2011 10:42:05 +0200 Message-ID: <1318927331-20855-2-git-send-email-peppe.cavallaro@st.com> References: <1318927331-20855-1-git-send-email-peppe.cavallaro@st.com> Cc: davem@davemloft.net, Srinivas Kandagatla , Giuseppe Cavallaro To: netdev@vger.kernel.org Return-path: Received: from eu1sys200aog112.obsmtp.com ([207.126.144.133]:33374 "EHLO eu1sys200aog112.obsmtp.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S932143Ab1JRInH (ORCPT ); Tue, 18 Oct 2011 04:43:07 -0400 In-Reply-To: <1318927331-20855-1-git-send-email-peppe.cavallaro@st.com> Sender: netdev-owner@vger.kernel.org List-ID: From: Srinivas Kandagatla This patch stops advertising 1000Base capablities if GMAC is either configured for MII or RMII mode and on board there is a GPHY plugged on. Without this patch if an GBit switch is connected on MII interface, Ethernet stops working at all. Discovered as part of https://bugzilla.stlinux.com/show_bug.cgi?id=14148 triage Signed-off-by: Srinivas Kandagatla Signed-off-by: Giuseppe Cavallaro --- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 13 ++++++++++--- 1 files changed, 10 insertions(+), 3 deletions(-) diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index c0ee6b6..229fe44 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -304,7 +304,7 @@ static int stmmac_init_phy(struct net_device *dev) struct phy_device *phydev; char phy_id[MII_BUS_ID_SIZE + 3]; char bus_id[MII_BUS_ID_SIZE]; - + int interface = priv->plat->interface; priv->oldlink = 0; priv->speed = 0; priv->oldduplex = -1; @@ -314,14 +314,21 @@ static int stmmac_init_phy(struct net_device *dev) priv->plat->phy_addr); pr_debug("stmmac_init_phy: trying to attach to %s\n", phy_id); - phydev = phy_connect(dev, phy_id, &stmmac_adjust_link, 0, - priv->plat->interface); + phydev = phy_connect(dev, phy_id, &stmmac_adjust_link, 0, interface); if (IS_ERR(phydev)) { pr_err("%s: Could not attach to PHY\n", dev->name); return PTR_ERR(phydev); } + /* Stop Advertising 1000BASE Capability if interface is not GMII */ + if ((interface) && ((interface == PHY_INTERFACE_MODE_MII) || + (interface == PHY_INTERFACE_MODE_RMII))) { + phydev->supported &= (PHY_BASIC_FEATURES | SUPPORTED_Pause | + SUPPORTED_Asym_Pause); + priv->phydev->advertising = priv->phydev->supported; + } + /* * Broken HW is sometimes missing the pull-up resistor on the * MDIO line, which results in reads to non-existent devices returning -- 1.7.4.4