From: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
To: David Miller <davem@davemloft.net>
Cc: netdev <netdev@vger.kernel.org>,
Ron Mercer <ron.mercer@qlogic.com>,
Dept_NX_Linux_NIC_Driver <Dept_NX_Linux_NIC_Driver@qlogic.com>,
Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Subject: [net-next PATCH 3/5] qlge: Removing needless print's which are not
Date: Fri, 3 Feb 2012 16:06:50 -0800 [thread overview]
Message-ID: <1328314013-20458-3-git-send-email-jitendra.kalsaria@qlogic.com> (raw)
In-Reply-To: <1328314013-20458-1-git-send-email-jitendra.kalsaria@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
---
drivers/net/ethernet/qlogic/qlge/qlge_main.c | 71 +-------------------------
1 files changed, 1 insertions(+), 70 deletions(-)
diff --git a/drivers/net/ethernet/qlogic/qlge/qlge_main.c b/drivers/net/ethernet/qlogic/qlge/qlge_main.c
index 582b237..af12e80 100644
--- a/drivers/net/ethernet/qlogic/qlge/qlge_main.c
+++ b/drivers/net/ethernet/qlogic/qlge/qlge_main.c
@@ -375,13 +375,6 @@ static int ql_set_mac_addr_reg(struct ql_adapter *qdev, u8 *addr, u32 type,
u32 lower =
(addr[2] << 24) | (addr[3] << 16) | (addr[4] << 8) |
(addr[5]);
-
- netif_printk(qdev, ifup, KERN_DEBUG, qdev->ndev,
- "Adding %s address %pM at index %d in the CAM.\n",
- type == MAC_ADDR_TYPE_MULTI_MAC ?
- "MULTICAST" : "UNICAST",
- addr, index);
-
status =
ql_wait_reg_rdy(qdev,
MAC_ADDR_IDX, MAC_ADDR_MW, 0);
@@ -430,12 +423,6 @@ static int ql_set_mac_addr_reg(struct ql_adapter *qdev, u8 *addr, u32 type,
* addressing. It's either MAC_ADDR_E on or off.
* That's bit-27 we're talking about.
*/
- netif_info(qdev, ifup, qdev->ndev,
- "%s VLAN ID %d %s the CAM.\n",
- enable_bit ? "Adding" : "Removing",
- index,
- enable_bit ? "to" : "from");
-
status =
ql_wait_reg_rdy(qdev,
MAC_ADDR_IDX, MAC_ADDR_MW, 0);
@@ -535,28 +522,6 @@ static int ql_set_routing_reg(struct ql_adapter *qdev, u32 index, u32 mask,
int status = -EINVAL; /* Return error if no mask match. */
u32 value = 0;
- netif_printk(qdev, ifup, KERN_DEBUG, qdev->ndev,
- "%s %s mask %s the routing reg.\n",
- enable ? "Adding" : "Removing",
- index == RT_IDX_ALL_ERR_SLOT ? "MAC ERROR/ALL ERROR" :
- index == RT_IDX_IP_CSUM_ERR_SLOT ? "IP CSUM ERROR" :
- index == RT_IDX_TCP_UDP_CSUM_ERR_SLOT ? "TCP/UDP CSUM ERROR" :
- index == RT_IDX_BCAST_SLOT ? "BROADCAST" :
- index == RT_IDX_MCAST_MATCH_SLOT ? "MULTICAST MATCH" :
- index == RT_IDX_ALLMULTI_SLOT ? "ALL MULTICAST MATCH" :
- index == RT_IDX_UNUSED6_SLOT ? "UNUSED6" :
- index == RT_IDX_UNUSED7_SLOT ? "UNUSED7" :
- index == RT_IDX_RSS_MATCH_SLOT ? "RSS ALL/IPV4 MATCH" :
- index == RT_IDX_RSS_IPV6_SLOT ? "RSS IPV6" :
- index == RT_IDX_RSS_TCP4_SLOT ? "RSS TCP4" :
- index == RT_IDX_RSS_TCP6_SLOT ? "RSS TCP6" :
- index == RT_IDX_CAM_HIT_SLOT ? "CAM HIT" :
- index == RT_IDX_UNUSED013 ? "UNUSED13" :
- index == RT_IDX_UNUSED014 ? "UNUSED14" :
- index == RT_IDX_PROMISCUOUS_SLOT ? "PROMISCUOUS" :
- "(Bad index != RT_IDX)",
- enable ? "to" : "from");
-
switch (mask) {
case RT_IDX_CAM_HIT:
{
@@ -2313,13 +2278,9 @@ static void qlge_vlan_mode(struct net_device *ndev, netdev_features_t features)
struct ql_adapter *qdev = netdev_priv(ndev);
if (features & NETIF_F_HW_VLAN_RX) {
- netif_printk(qdev, ifup, KERN_DEBUG, ndev,
- "Turning on VLAN in NIC_RCV_CFG.\n");
ql_write32(qdev, NIC_RCV_CFG, NIC_RCV_CFG_VLAN_MASK |
NIC_RCV_CFG_VLAN_MATCH_AND_NON);
} else {
- netif_printk(qdev, ifup, KERN_DEBUG, ndev,
- "Turning off VLAN in NIC_RCV_CFG.\n");
ql_write32(qdev, NIC_RCV_CFG, NIC_RCV_CFG_VLAN_MASK);
}
}
@@ -3184,8 +3145,6 @@ static int ql_start_rx_ring(struct ql_adapter *qdev, struct rx_ring *rx_ring)
netif_printk(qdev, ifup, KERN_DEBUG, qdev->ndev,
"Invalid rx_ring->type = %d.\n", rx_ring->type);
}
- netif_printk(qdev, ifup, KERN_DEBUG, qdev->ndev,
- "Initializing rx work queue.\n");
err = ql_write_cfg(qdev, cqicb, sizeof(struct cqicb),
CFG_LCQ, rx_ring->cq_id);
if (err) {
@@ -3238,8 +3197,6 @@ static int ql_start_tx_ring(struct ql_adapter *qdev, struct tx_ring *tx_ring)
netif_err(qdev, ifup, qdev->ndev, "Failed to load tx_ring.\n");
return err;
}
- netif_printk(qdev, ifup, KERN_DEBUG, qdev->ndev,
- "Successfully loaded WQICB.\n");
return err;
}
@@ -3489,12 +3446,8 @@ static void ql_free_irq(struct ql_adapter *qdev)
if (test_bit(QL_MSIX_ENABLED, &qdev->flags)) {
free_irq(qdev->msi_x_entry[i].vector,
&qdev->rx_ring[i]);
- netif_printk(qdev, ifdown, KERN_DEBUG, qdev->ndev,
- "freeing msix interrupt %d.\n", i);
} else {
free_irq(qdev->pdev->irq, &qdev->rx_ring[0]);
- netif_printk(qdev, ifdown, KERN_DEBUG, qdev->ndev,
- "freeing msi interrupt %d.\n", i);
}
}
}
@@ -3523,17 +3476,6 @@ static int ql_request_irq(struct ql_adapter *qdev)
"Failed request for MSIX interrupt %d.\n",
i);
goto err_irq;
- } else {
- netif_printk(qdev, ifup, KERN_DEBUG, qdev->ndev,
- "Hooked intr %d, queue type %s, with name %s.\n",
- i,
- qdev->rx_ring[i].type == DEFAULT_Q ?
- "DEFAULT_Q" :
- qdev->rx_ring[i].type == TX_Q ?
- "TX_Q" :
- qdev->rx_ring[i].type == RX_Q ?
- "RX_Q" : "",
- intr_context->name);
}
} else {
netif_printk(qdev, ifup, KERN_DEBUG, qdev->ndev,
@@ -3603,15 +3545,11 @@ static int ql_start_rss(struct ql_adapter *qdev)
memcpy((void *)&ricb->ipv6_hash_key[0], init_hash_seed, 40);
memcpy((void *)&ricb->ipv4_hash_key[0], init_hash_seed, 16);
- netif_printk(qdev, ifup, KERN_DEBUG, qdev->ndev, "Initializing RSS.\n");
-
status = ql_write_cfg(qdev, ricb, sizeof(*ricb), CFG_LR, 0);
if (status) {
netif_err(qdev, ifup, qdev->ndev, "Failed to load RICB.\n");
return status;
}
- netif_printk(qdev, ifup, KERN_DEBUG, qdev->ndev,
- "Successfully loaded RICB.\n");
return status;
}
@@ -3818,11 +3756,8 @@ static int ql_adapter_initialize(struct ql_adapter *qdev)
}
/* Start NAPI for the RSS queues. */
- for (i = 0; i < qdev->rss_ring_count; i++) {
- netif_printk(qdev, ifup, KERN_DEBUG, qdev->ndev,
- "Enabling NAPI for rx_ring[%d].\n", i);
+ for (i = 0; i < qdev->rss_ring_count; i++)
napi_enable(&qdev->rx_ring[i].napi);
- }
return status;
}
@@ -4122,10 +4057,6 @@ static int ql_configure_rings(struct ql_adapter *qdev)
rx_ring->lbq_size =
rx_ring->lbq_len * sizeof(__le64);
rx_ring->lbq_buf_size = (u16)lbq_buf_len;
- netif_printk(qdev, ifup, KERN_DEBUG, qdev->ndev,
- "lbq_buf_size %d, order = %d\n",
- rx_ring->lbq_buf_size,
- qdev->lbq_buf_order);
rx_ring->sbq_len = NUM_SMALL_BUFFERS;
rx_ring->sbq_size =
rx_ring->sbq_len * sizeof(__le64);
--
1.7.6.rc1.1.g2c162b
next prev parent reply other threads:[~2012-02-04 0:22 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-02-04 0:06 [net-next PATCH 1/5] qlge: Updating Schultz LICENSE.qlge file Jitendra Kalsaria
2012-02-04 0:06 ` [net-next PATCH 2/5] qlge: Fixed invalid reference to ip header Jitendra Kalsaria
2012-02-04 0:06 ` Jitendra Kalsaria [this message]
2012-02-04 1:28 ` [net-next PATCH 3/5] qlge: Removing needless print's which are not Jitendra Kalsaria
2012-02-04 0:06 ` [net-next PATCH 4/5] qlge: Fix memory leak in the process of refill Jitendra Kalsaria
2012-02-04 0:06 ` [net-next PATCH 5/5] qlge: Bumped driver version to 1.00.00.30 Jitendra Kalsaria
2012-02-04 0:06 ` [net-next PATCH 0/5] qlge: Fixes Jitendra Kalsaria
2012-02-04 21:04 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1328314013-20458-3-git-send-email-jitendra.kalsaria@qlogic.com \
--to=jitendra.kalsaria@qlogic.com \
--cc=Dept_NX_Linux_NIC_Driver@qlogic.com \
--cc=davem@davemloft.net \
--cc=netdev@vger.kernel.org \
--cc=ron.mercer@qlogic.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).