From: "Yuval Mintz" <yuvalmin@broadcom.com>
To: davem@davemloft.net, netdev@vger.kernel.org
Cc: eilong@broadcom.com, peppe.cavallaro@st.com,
bhutchings@solarflare.com, "Yuval Mintz" <yuvalmin@broadcom.com>
Subject: [v4 net-next PATCH 1/3] Added kernel support in EEE Ethtool commands
Date: Thu, 7 Jun 2012 06:13:06 +0300 [thread overview]
Message-ID: <1339038788-3447-2-git-send-email-yuvalmin@broadcom.com> (raw)
In-Reply-To: <1339038788-3447-1-git-send-email-yuvalmin@broadcom.com>
This patch extends the kernel's ethtool interface by adding support
for 2 new EEE commands - get_eee and set_eee.
Thanks goes to Giuseppe Cavallaro for his original patch adding this support.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
---
include/linux/ethtool.h | 35 +++++++++++++++++++++++++++++++++++
net/core/ethtool.c | 40 ++++++++++++++++++++++++++++++++++++++++
2 files changed, 75 insertions(+), 0 deletions(-)
diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h
index e17fa71..a518361 100644
--- a/include/linux/ethtool.h
+++ b/include/linux/ethtool.h
@@ -137,6 +137,35 @@ struct ethtool_eeprom {
};
/**
+ * struct ethtool_eee - Energy Efficient Ethernet information
+ * @cmd: ETHTOOL_{G,S}EEE
+ * @supported: Mask of %SUPPORTED_* flags for the speed/duplex combinations
+ * for which there is EEE support.
+ * @advertised: Mask of %ADVERTISED_* flags for the speed/duplex combinations
+ * advertised as eee capable.
+ * @lp_advertised: Mask of %ADVERTISED_* flags for the speed/duplex
+ * combinations advertised by the link partner as eee capable.
+ * @eee_active: Result of the eee auto negotiation.
+ * @eee_enabled: EEE configured mode (enabled/disabled).
+ * @tx_lpi_enabled: Whether the interface should assert its tx lpi, given
+ * that eee was negotiated.
+ * @tx_lpi_timer: Time in microseconds the interface delays prior to asserting
+ * its tx lpi (after reaching 'idle' state). Effective only when eee
+ * was negotiated and tx_lpi_enabled was set.
+ */
+struct ethtool_eee {
+ __u32 cmd;
+ __u32 supported;
+ __u32 advertised;
+ __u32 lp_advertised;
+ __u32 eee_active;
+ __u32 eee_enabled;
+ __u32 tx_lpi_enabled;
+ __u32 tx_lpi_timer;
+ __u32 reserved[2];
+};
+
+/**
* struct ethtool_modinfo - plugin module eeprom information
* @cmd: %ETHTOOL_GMODULEINFO
* @type: Standard the module information conforms to %ETH_MODULE_SFF_xxxx
@@ -945,6 +974,8 @@ static inline u32 ethtool_rxfh_indir_default(u32 index, u32 n_rx_rings)
* @get_module_info: Get the size and type of the eeprom contained within
* a plug-in module.
* @get_module_eeprom: Get the eeprom information from the plug-in module
+ * @get_eee: Get Energy-Efficient (EEE) supported and status.
+ * @set_eee: Set EEE status (enable/disable) as well as LPI timers.
*
* All operations are optional (i.e. the function pointer may be set
* to %NULL) and callers must take this into account. Callers must
@@ -1011,6 +1042,8 @@ struct ethtool_ops {
struct ethtool_modinfo *);
int (*get_module_eeprom)(struct net_device *,
struct ethtool_eeprom *, u8 *);
+ int (*get_eee)(struct net_device *, struct ethtool_eee *);
+ int (*set_eee)(struct net_device *, struct ethtool_eee *);
};
@@ -1089,6 +1122,8 @@ struct ethtool_ops {
#define ETHTOOL_GET_TS_INFO 0x00000041 /* Get time stamping and PHC info */
#define ETHTOOL_GMODULEINFO 0x00000042 /* Get plug-in module information */
#define ETHTOOL_GMODULEEEPROM 0x00000043 /* Get plug-in module eeprom */
+#define ETHTOOL_GEEE 0x00000044 /* Get EEE settings */
+#define ETHTOOL_SEEE 0x00000045 /* Set EEE settings */
/* compatibility with older code */
#define SPARC_ETH_GSET ETHTOOL_GSET
diff --git a/net/core/ethtool.c b/net/core/ethtool.c
index 9c2afb4..5a582da 100644
--- a/net/core/ethtool.c
+++ b/net/core/ethtool.c
@@ -729,6 +729,40 @@ static int ethtool_set_wol(struct net_device *dev, char __user *useraddr)
return dev->ethtool_ops->set_wol(dev, &wol);
}
+static int ethtool_get_eee(struct net_device *dev, char __user *useraddr)
+{
+ struct ethtool_eee edata;
+ int rc;
+
+ if (!dev->ethtool_ops->get_eee)
+ return -EOPNOTSUPP;
+
+ memset(&edata, 0, sizeof(struct ethtool_eee));
+ edata.cmd = ETHTOOL_GEEE;
+ rc = dev->ethtool_ops->get_eee(dev, &edata);
+
+ if (rc)
+ return rc;
+
+ if (copy_to_user(useraddr, &edata, sizeof(edata)))
+ return -EFAULT;
+
+ return 0;
+}
+
+static int ethtool_set_eee(struct net_device *dev, char __user *useraddr)
+{
+ struct ethtool_eee edata;
+
+ if (!dev->ethtool_ops->set_eee)
+ return -EOPNOTSUPP;
+
+ if (copy_from_user(&edata, useraddr, sizeof(edata)))
+ return -EFAULT;
+
+ return dev->ethtool_ops->set_eee(dev, &edata);
+}
+
static int ethtool_nway_reset(struct net_device *dev)
{
if (!dev->ethtool_ops->nway_reset)
@@ -1471,6 +1505,12 @@ int dev_ethtool(struct net *net, struct ifreq *ifr)
rc = ethtool_set_value_void(dev, useraddr,
dev->ethtool_ops->set_msglevel);
break;
+ case ETHTOOL_GEEE:
+ rc = ethtool_get_eee(dev, useraddr);
+ break;
+ case ETHTOOL_SEEE:
+ rc = ethtool_set_eee(dev, useraddr);
+ break;
case ETHTOOL_NWAY_RST:
rc = ethtool_nway_reset(dev);
break;
--
1.7.9.rc2
next prev parent reply other threads:[~2012-06-07 3:14 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-06-07 3:13 [v4 net-next PATCH 0/3] Energy Efficient Ethernet (eee) support Yuval Mintz
2012-06-07 3:13 ` Yuval Mintz [this message]
2012-06-07 16:28 ` [v4 net-next PATCH 1/3] Added kernel support in EEE Ethtool commands Ben Hutchings
2012-06-07 3:13 ` [v4 net-next PATCH 2/3] bnx2x: Added EEE support Yuval Mintz
2012-06-07 3:13 ` [v4 net-next PATCH 3/3] bnx2x: Added EEE Ethtool support Yuval Mintz
2012-06-07 20:19 ` [v4 net-next PATCH 0/3] Energy Efficient Ethernet (eee) support David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1339038788-3447-2-git-send-email-yuvalmin@broadcom.com \
--to=yuvalmin@broadcom.com \
--cc=bhutchings@solarflare.com \
--cc=davem@davemloft.net \
--cc=eilong@broadcom.com \
--cc=netdev@vger.kernel.org \
--cc=peppe.cavallaro@st.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).