[net-next 5/6] e1000e: implement MDI/MDI-X control

[Jeff Kirsher <jeffrey.t.kirsher@intel.com>]

From: Jesse Brandeburg <jesse.brandeburg@intel.com>

Some users report issues with link failing when connected to certain
switches.  This gives the user the ability to control the MDI state
from the driver, allowing users to work around some improperly
behaving switches.

Current get_settings behavior slightly changes in that now when link
is down get_settings will return the MDI state of the last link
because get_settings needs to succeed to allow the set to work even
when link is down.

Forcing in this driver is for now only allowed when auto-neg is
enabled.

This is in regards to the related ethtool app patch and
bugzilla.kernel.org bug 11998

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: bruce.w.allan@intel.com
CC: n.poppelier@xs4all.nl
CC: bastien@durel.org
CC: jsveiga@it.eng.br
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/ethtool.c |   39 ++++++++++++++++++++++++---
 1 file changed, 35 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index 105d554..9b1e082 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -192,8 +192,7 @@ static int e1000_get_settings(struct net_device *netdev,
 			 hw->mac.autoneg) ? AUTONEG_ENABLE : AUTONEG_DISABLE;
 
 	/* MDI-X => 2; MDI =>1; Invalid =>0 */
-	if ((hw->phy.media_type == e1000_media_type_copper) &&
-	    netif_carrier_ok(netdev))
+	if (hw->phy.media_type == e1000_media_type_copper)
 		ecmd->eth_tp_mdix = hw->phy.is_mdix ? ETH_TP_MDI_X :
 		                                      ETH_TP_MDI;
 	else
@@ -241,6 +240,10 @@ static int e1000_set_spd_dplx(struct e1000_adapter *adapter, u32 spd, u8 dplx)
 	default:
 		goto err_inval;
 	}
+
+	/* clear MDI, MDI(-X) override is only allowed when autoneg enabled */
+	adapter->hw.phy.mdix = AUTO_ALL_MODES;
+
 	return 0;
 
 err_inval:
@@ -264,6 +267,22 @@ static int e1000_set_settings(struct net_device *netdev,
 		return -EINVAL;
 	}
 
+	/*
+	 * MDI setting is only allowed when autoneg enabled because
+	 * some hardware doesn't allow MDI setting when speed or
+	 * duplex is forced.
+	 */
+	if (ecmd->eth_tp_mdix_ctrl) {
+		if (hw->phy.media_type != e1000_media_type_copper)
+			return -EOPNOTSUPP;
+
+		if ((ecmd->eth_tp_mdix_ctrl != ETH_TP_MDI_AUTO) &&
+		    (ecmd->autoneg != AUTONEG_ENABLE)) {
+			e_err("forcing MDI/MDI-X state is not supported when link speed and/or duplex are forced\n");
+			return -EINVAL;
+		}
+	}
+
 	while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
 		usleep_range(1000, 2000);
 
@@ -282,20 +301,32 @@ static int e1000_set_settings(struct net_device *netdev,
 			hw->fc.requested_mode = e1000_fc_default;
 	} else {
 		u32 speed = ethtool_cmd_speed(ecmd);
+		/* calling this overrides forced MDI setting */
 		if (e1000_set_spd_dplx(adapter, speed, ecmd->duplex)) {
 			clear_bit(__E1000_RESETTING, &adapter->state);
 			return -EINVAL;
 		}
 	}
 
+	/* MDI-X => 2; MDI => 1; Auto => 3 */
+	if (ecmd->eth_tp_mdix_ctrl) {
+		/*
+		 * fix up the value for auto (3 => 0) as zero is mapped
+		 * internally to auto
+		 */
+		if (ecmd->eth_tp_mdix_ctrl == ETH_TP_MDI_AUTO)
+			hw->phy.mdix = AUTO_ALL_MODES;
+		else
+			hw->phy.mdix = ecmd->eth_tp_mdix_ctrl;
+	}
+
 	/* reset the link */
 
 	if (netif_running(adapter->netdev)) {
 		e1000e_down(adapter);
 		e1000e_up(adapter);
-	} else {
+	} else
 		e1000e_reset(adapter);
-	}
 
 	clear_bit(__E1000_RESETTING, &adapter->state);
 	return 0;
-- 
1.7.10.4