From: Joe Perches <joe@perches.com>
To: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: netdev@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH] ixgbe: Use is_valid_ether_addr
Date: Sat, 20 Oct 2012 09:22:39 -0700 [thread overview]
Message-ID: <1350750159.10791.3.camel@joe-AO722> (raw)
Use the normal kernel test instead of a module specific one.
Signed-off-by: Joe Perches <joe@perches.com>
---
found when doing that larger style conversion,
might as well submit it.
drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c | 2 +-
drivers/net/ethernet/intel/ixgbe/ixgbe_common.c | 27 +------------------------
drivers/net/ethernet/intel/ixgbe/ixgbe_common.h | 1 -
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 2 +-
drivers/net/ethernet/intel/ixgbe/ixgbe_type.h | 9 ---------
drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c | 2 +-
6 files changed, 4 insertions(+), 39 deletions(-)
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c
index 1077cb2..89fe00d 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c
@@ -1022,7 +1022,7 @@ mac_reset_top:
hw->mac.ops.get_san_mac_addr(hw, hw->mac.san_addr);
/* Add the SAN MAC address to the RAR only if it's a valid address */
- if (ixgbe_validate_mac_addr(hw->mac.san_addr) == 0) {
+ if (is_valid_ether_addr(hw->mac.san_addr)) {
hw->mac.ops.set_rar(hw, hw->mac.num_rar_entries - 1,
hw->mac.san_addr, 0, IXGBE_RAH_AV);
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
index dbf37e4..2d8f76d 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c
@@ -1762,30 +1762,6 @@ s32 ixgbe_update_eeprom_checksum_generic(struct ixgbe_hw *hw)
}
/**
- * ixgbe_validate_mac_addr - Validate MAC address
- * @mac_addr: pointer to MAC address.
- *
- * Tests a MAC address to ensure it is a valid Individual Address
- **/
-s32 ixgbe_validate_mac_addr(u8 *mac_addr)
-{
- s32 status = 0;
-
- /* Make sure it is not a multicast address */
- if (IXGBE_IS_MULTICAST(mac_addr))
- status = IXGBE_ERR_INVALID_MAC_ADDR;
- /* Not a broadcast address */
- else if (IXGBE_IS_BROADCAST(mac_addr))
- status = IXGBE_ERR_INVALID_MAC_ADDR;
- /* Reject the zero address */
- else if (mac_addr[0] == 0 && mac_addr[1] == 0 && mac_addr[2] == 0 &&
- mac_addr[3] == 0 && mac_addr[4] == 0 && mac_addr[5] == 0)
- status = IXGBE_ERR_INVALID_MAC_ADDR;
-
- return status;
-}
-
-/**
* ixgbe_set_rar_generic - Set Rx address register
* @hw: pointer to hardware structure
* @index: Receive address register to write
@@ -1889,8 +1865,7 @@ s32 ixgbe_init_rx_addrs_generic(struct ixgbe_hw *hw)
* to the permanent address.
* Otherwise, use the permanent address from the eeprom.
*/
- if (ixgbe_validate_mac_addr(hw->mac.addr) ==
- IXGBE_ERR_INVALID_MAC_ADDR) {
+ if (!is_valid_ether_addr(hw->mac.addr)) {
/* Get the MAC address from the RAR0 for later reference */
hw->mac.ops.get_mac_addr(hw, hw->mac.addr);
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
index d813d11..f49ca84 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
@@ -80,7 +80,6 @@ s32 ixgbe_enable_rx_dma_generic(struct ixgbe_hw *hw, u32 regval);
s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw);
void ixgbe_fc_autoneg(struct ixgbe_hw *hw);
-s32 ixgbe_validate_mac_addr(u8 *mac_addr);
s32 ixgbe_acquire_swfw_sync(struct ixgbe_hw *hw, u16 mask);
void ixgbe_release_swfw_sync(struct ixgbe_hw *hw, u16 mask);
s32 ixgbe_get_san_mac_addr_generic(struct ixgbe_hw *hw, u8 *san_mac_addr);
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
index e2a6691..3bb3485 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
@@ -7345,7 +7345,7 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev,
memcpy(netdev->dev_addr, hw->mac.perm_addr, netdev->addr_len);
memcpy(netdev->perm_addr, hw->mac.perm_addr, netdev->addr_len);
- if (ixgbe_validate_mac_addr(netdev->perm_addr)) {
+ if (!is_valid_ether_addr(netdev->perm_addr)) {
e_dev_err("invalid MAC address\n");
err = -EIO;
goto err_sw_init;
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
index 0722f33..9ddac64 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_type.h
@@ -1833,15 +1833,6 @@ enum {
/* Number of 100 microseconds we wait for PCI Express master disable */
#define IXGBE_PCI_MASTER_DISABLE_TIMEOUT 800
-/* Check whether address is multicast. This is little-endian specific check.*/
-#define IXGBE_IS_MULTICAST(Address) \
- (bool)(((u8 *)(Address))[0] & ((u8)0x01))
-
-/* Check whether an address is broadcast. */
-#define IXGBE_IS_BROADCAST(Address) \
- ((((u8 *)(Address))[0] == ((u8)0xff)) && \
- (((u8 *)(Address))[1] == ((u8)0xff)))
-
/* RAH */
#define IXGBE_RAH_VIND_MASK 0x003C0000
#define IXGBE_RAH_VIND_SHIFT 18
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c
index de4da52..c73b929 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x540.c
@@ -152,7 +152,7 @@ mac_reset_top:
hw->mac.ops.get_san_mac_addr(hw, hw->mac.san_addr);
/* Add the SAN MAC address to the RAR only if it's a valid address */
- if (ixgbe_validate_mac_addr(hw->mac.san_addr) == 0) {
+ if (is_valid_ether_addr(hw->mac.san_addr)) {
hw->mac.ops.set_rar(hw, hw->mac.num_rar_entries - 1,
hw->mac.san_addr, 0, IXGBE_RAH_AV);
next reply other threads:[~2012-10-20 16:22 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-10-20 16:22 Joe Perches [this message]
2012-10-22 0:23 ` [PATCH] ixgbe: Use is_valid_ether_addr Jeff Kirsher
2012-12-03 17:47 ` Joe Perches
2012-12-03 21:04 ` Jeff Kirsher
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1350750159.10791.3.camel@joe-AO722 \
--to=joe@perches.com \
--cc=jeffrey.t.kirsher@intel.com \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).