From: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To: davem@davemloft.net
Cc: Don Skidmore <donald.c.skidmore@intel.com>,
netdev@vger.kernel.org, gospo@redhat.com, sassmann@redhat.com,
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Subject: [net-next 11/12] ixgbe: Add function ixgbe_reset_pipeline_82599
Date: Mon, 22 Oct 2012 21:26:24 -0700 [thread overview]
Message-ID: <1350966385-19020-12-git-send-email-jeffrey.t.kirsher@intel.com> (raw)
In-Reply-To: <1350966385-19020-1-git-send-email-jeffrey.t.kirsher@intel.com>
From: Don Skidmore <donald.c.skidmore@intel.com>
This patch adds a function that forces a full pipeline reset. This
function will be used in following patches to completely reset the PHY
during resets.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c | 44 +++++++++++++++++++++++++
drivers/net/ethernet/intel/ixgbe/ixgbe_common.h | 1 +
2 files changed, 45 insertions(+)
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c
index 1077cb2..b527813 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_82599.c
@@ -2080,6 +2080,50 @@ static s32 ixgbe_read_eeprom_82599(struct ixgbe_hw *hw,
return ret_val;
}
+/**
+ * ixgbe_reset_pipeline_82599 - perform pipeline reset
+ *
+ * @hw: pointer to hardware structure
+ *
+ * Reset pipeline by asserting Restart_AN together with LMS change to ensure
+ * full pipeline reset. Note - We must hold the SW/FW semaphore before writing
+ * to AUTOC, so this function assumes the semaphore is held.
+ **/
+s32 ixgbe_reset_pipeline_82599(struct ixgbe_hw *hw)
+{
+ s32 i, autoc_reg, ret_val;
+ s32 anlp1_reg = 0;
+
+ autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+ autoc_reg |= IXGBE_AUTOC_AN_RESTART;
+
+ /* Write AUTOC register with toggled LMS[2] bit and Restart_AN */
+ IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg ^ IXGBE_AUTOC_LMS_1G_AN);
+
+ /* Wait for AN to leave state 0 */
+ for (i = 0; i < 10; i++) {
+ usleep_range(4000, 8000);
+ anlp1_reg = IXGBE_READ_REG(hw, IXGBE_ANLP1);
+ if (anlp1_reg & IXGBE_ANLP1_AN_STATE_MASK)
+ break;
+ }
+
+ if (!(anlp1_reg & IXGBE_ANLP1_AN_STATE_MASK)) {
+ hw_dbg(hw, "auto negotiation not completed\n");
+ ret_val = IXGBE_ERR_RESET_FAILED;
+ goto reset_pipeline_out;
+ }
+
+ ret_val = 0;
+
+reset_pipeline_out:
+ /* Write AUTOC register with original LMS field and Restart_AN */
+ IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg);
+ IXGBE_WRITE_FLUSH(hw);
+
+ return ret_val;
+}
+
static struct ixgbe_mac_operations mac_ops_82599 = {
.init_hw = &ixgbe_init_hw_generic,
.reset_hw = &ixgbe_reset_hw_82599,
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
index d813d11..587db47 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
@@ -107,6 +107,7 @@ void ixgbe_clear_tx_pending(struct ixgbe_hw *hw);
void ixgbe_set_rxpba_generic(struct ixgbe_hw *hw, int num_pb,
u32 headroom, int strategy);
+s32 ixgbe_reset_pipeline_82599(struct ixgbe_hw *hw);
#define IXGBE_I2C_THERMAL_SENSOR_ADDR 0xF8
#define IXGBE_EMC_INTERNAL_DATA 0x00
--
1.7.11.7
next prev parent reply other threads:[~2012-10-23 4:26 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-10-23 4:26 [net-next 00/12][pull request] Intel Wired LAN Driver Updates Jeff Kirsher
2012-10-23 4:26 ` [net-next 01/12] ixgbe: Add support for IPv6 and UDP to ixgbe_get_headlen Jeff Kirsher
2012-10-23 4:26 ` [net-next 02/12] ixgbe: Add support for tracking the default user priority to SR-IOV Jeff Kirsher
2012-10-23 4:26 ` [net-next 03/12] ixgbe: Add support for GET_QUEUES message to get DCB configuration Jeff Kirsher
2012-10-23 4:26 ` [net-next 04/12] ixgbe: Enable support for VF API version 1.1 in the PF Jeff Kirsher
2012-10-23 4:26 ` [net-next 05/12] ixgbevf: Add VF DCB + SR-IOV support Jeff Kirsher
2012-10-23 4:26 ` [net-next 06/12] ixgbe: add WOL support for new subdevice id Jeff Kirsher
2012-10-23 4:26 ` [net-next 07/12] ixgbe: (PTP) refactor init, cyclecounter and reset Jeff Kirsher
2012-10-23 4:26 ` [net-next 08/12] ixgbe: using is_zero_ether_addr() to simplify the code Jeff Kirsher
2012-10-23 4:45 ` Joe Perches
2012-10-23 5:17 ` Jeff Kirsher
2012-10-23 19:35 ` Joe Perches
2012-10-23 4:26 ` [net-next 09/12] ixgbe: Correcting small packet padding Jeff Kirsher
2012-10-23 4:26 ` [net-next 10/12] ixgbe: Drop unnecessary addition from ixgbe_set_rx_buffer_len Jeff Kirsher
2012-10-23 4:26 ` Jeff Kirsher [this message]
2012-10-23 4:26 ` [net-next 12/12] ixgbe: Fix possible memory leak in ixgbe_set_ringparam Jeff Kirsher
2012-10-23 6:51 ` [net-next 00/12][pull request] Intel Wired LAN Driver Updates David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1350966385-19020-12-git-send-email-jeffrey.t.kirsher@intel.com \
--to=jeffrey.t.kirsher@intel.com \
--cc=davem@davemloft.net \
--cc=donald.c.skidmore@intel.com \
--cc=gospo@redhat.com \
--cc=netdev@vger.kernel.org \
--cc=sassmann@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).