From: Antonio Quartulli <ordex@autistici.org>
To: davem@davemloft.net
Cc: netdev@vger.kernel.org, b.a.t.m.a.n@lists.open-mesh.org,
Sven Eckelmann <sven@narfation.org>,
Antonio Quartulli <ordex@autistici.org>
Subject: [PATCH 06/16] batman-adv: Set special lockdep classes to avoid lockdep warning
Date: Mon, 29 Oct 2012 09:58:07 +0100 [thread overview]
Message-ID: <1351501097-1289-7-git-send-email-ordex@autistici.org> (raw)
In-Reply-To: <1351501097-1289-1-git-send-email-ordex@autistici.org>
From: Sven Eckelmann <sven@narfation.org>
Transmissions over batman-adv devices always start another nested transmission
over devices attached to the batman-adv interface. These devices usually use
the ethernet lockdep class for the tx_queue lock which is also set by default
for all batman-adv devices. Lockdep will detect a nested locking attempt of two
locks with the same class and warn about a possible deadlock.
This is the default and expected behavior and should not alarm the locking
correctness prove mechanism. Therefore, the locks for all netdevice specific tx
queues get a special batman-adv lock class to avoid a false positive for each
transmission.
Reported-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
---
net/batman-adv/soft-interface.c | 44 +++++++++++++++++++++++++++++++++++++++++
1 file changed, 44 insertions(+)
diff --git a/net/batman-adv/soft-interface.c b/net/batman-adv/soft-interface.c
index b9a28d2..948860a 100644
--- a/net/batman-adv/soft-interface.c
+++ b/net/batman-adv/soft-interface.c
@@ -347,7 +347,51 @@ out:
return;
}
+/* batman-adv network devices have devices nesting below it and are a special
+ * "super class" of normal network devices; split their locks off into a
+ * separate class since they always nest.
+ */
+static struct lock_class_key batadv_netdev_xmit_lock_key;
+static struct lock_class_key batadv_netdev_addr_lock_key;
+
+/**
+ * batadv_set_lockdep_class_one - Set lockdep class for a single tx queue
+ * @dev: device which owns the tx queue
+ * @txq: tx queue to modify
+ * @_unused: always NULL
+ */
+static void batadv_set_lockdep_class_one(struct net_device *dev,
+ struct netdev_queue *txq,
+ void *_unused)
+{
+ lockdep_set_class(&txq->_xmit_lock, &batadv_netdev_xmit_lock_key);
+}
+
+/**
+ * batadv_set_lockdep_class - Set txq and addr_list lockdep class
+ * @dev: network device to modify
+ */
+static void batadv_set_lockdep_class(struct net_device *dev)
+{
+ lockdep_set_class(&dev->addr_list_lock, &batadv_netdev_addr_lock_key);
+ netdev_for_each_tx_queue(dev, batadv_set_lockdep_class_one, NULL);
+}
+
+/**
+ * batadv_softif_init - Late stage initialization of soft interface
+ * @dev: registered network device to modify
+ *
+ * Returns error code on failures
+ */
+static int batadv_softif_init(struct net_device *dev)
+{
+ batadv_set_lockdep_class(dev);
+
+ return 0;
+}
+
static const struct net_device_ops batadv_netdev_ops = {
+ .ndo_init = batadv_softif_init,
.ndo_open = batadv_interface_open,
.ndo_stop = batadv_interface_release,
.ndo_get_stats = batadv_interface_stats,
--
1.7.12.4
next prev parent reply other threads:[~2012-10-29 8:59 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-10-29 8:58 pull request: batman-adv 202-10-29 Antonio Quartulli
2012-10-29 8:58 ` [PATCH 01/16] batman-adv: use check_unicast_packet() in recv_roam_adv() Antonio Quartulli
[not found] ` <1351501097-1289-1-git-send-email-ordex-GaUfNO9RBHfsrOwW+9ziJQ@public.gmane.org>
2012-10-29 8:58 ` [PATCH 02/16] batman-adv: split hard_iface struct for each routing protocol Antonio Quartulli
2012-10-29 8:58 ` [PATCH 03/16] batman-adv: Remove unused define BAT_ATTR_HIF_UINT Antonio Quartulli
2012-10-29 8:58 ` [PATCH 04/16] batman-adv: consolidate duplicated primary_if checking code Antonio Quartulli
2012-10-29 8:58 ` [PATCH 05/16] batman-adv: return proper value in case of hash_add failure Antonio Quartulli
2012-10-29 8:58 ` Antonio Quartulli [this message]
2012-10-29 8:58 ` [PATCH 07/16] batman-adv: Remove extra check in batadv_bit_get_packet Antonio Quartulli
2012-10-29 8:58 ` [PATCH 08/16] batman-adv: Check return value of try_module_get Antonio Quartulli
2012-10-29 8:58 ` [PATCH 09/16] batman-adv: Only increase refcounter once for alternate router Antonio Quartulli
2012-10-29 8:58 ` [PATCH 10/16] batman-adv: don't allow ECTP traffic on batman-adv Antonio Quartulli
2012-10-29 8:58 ` [PATCH 11/16] batman-adv: properly store the roaming time Antonio Quartulli
2012-10-29 8:58 ` [PATCH 12/16] batman-adv: print packets re-routing on DBG_TT and ratelimit it Antonio Quartulli
2012-10-29 8:58 ` [PATCH 13/16] batman-adv: check for more space before accessing the skb Antonio Quartulli
2012-10-29 8:58 ` [PATCH 14/16] batman-adv: properly convert flag into a boolean value Antonio Quartulli
2012-10-29 8:58 ` [PATCH 15/16] batman-adv: pass the WIFI flag from the local to global entry Antonio Quartulli
2012-10-29 8:58 ` [PATCH 16/16] batman-adv: add kernel-doc for enum batadv_dbg_level Antonio Quartulli
2012-10-31 17:53 ` pull request: batman-adv 202-10-29 David Miller
-- strict thread matches above, loose matches on Subject: below --
2012-10-28 11:17 pull request: batman-adv 2012-10-28 Antonio Quartulli
2012-10-28 11:17 ` [PATCH 06/16] batman-adv: Set special lockdep classes to avoid lockdep warning Antonio Quartulli
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1351501097-1289-7-git-send-email-ordex@autistici.org \
--to=ordex@autistici.org \
--cc=b.a.t.m.a.n@lists.open-mesh.org \
--cc=davem@davemloft.net \
--cc=netdev@vger.kernel.org \
--cc=sven@narfation.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox