From: David Woodhouse <dwmw2@infradead.org>
To: netdev@vger.kernel.org
Cc: Nathan Williams <nathan@traverse.com.au>
Subject: [PATCH 1/4] solos-pci: add GPIO support for newer versions on Geos board
Date: Wed, 19 Dec 2012 21:01:18 +0000 [thread overview]
Message-ID: <1355950881-31550-1-git-send-email-dwmw2@infradead.org> (raw)
From: Nathan Williams <nathan@traverse.com.au>
dwmw2: Tidy up a little, simpler matching on which GPIO is being accessed,
only register on newer boards, register under PCI device instead of
duplicating them under each ATM device.
Signed-off-by: Nathan Williams <nathan@traverse.com.au>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
---
drivers/atm/solos-pci.c | 105 ++++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 105 insertions(+)
diff --git a/drivers/atm/solos-pci.c b/drivers/atm/solos-pci.c
index c909b7b..473d808 100644
--- a/drivers/atm/solos-pci.c
+++ b/drivers/atm/solos-pci.c
@@ -56,6 +56,7 @@
#define FLASH_BUSY 0x60
#define FPGA_MODE 0x5C
#define FLASH_MODE 0x58
+#define GPIO_STATUS 0x54
#define TX_DMA_ADDR(port) (0x40 + (4 * (port)))
#define RX_DMA_ADDR(port) (0x30 + (4 * (port)))
@@ -498,6 +499,78 @@ static ssize_t console_store(struct device *dev, struct device_attribute *attr,
return err?:count;
}
+struct geos_gpio_attr {
+ struct device_attribute attr;
+ int offset;
+};
+
+#define SOLOS_GPIO_ATTR(_name, _mode, _show, _store, _offset) \
+ struct geos_gpio_attr gpio_attr_##_name = { \
+ .attr = __ATTR(_name, _mode, _show, _store), \
+ .offset = _offset }
+
+static ssize_t geos_gpio_store(struct device *dev, struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct pci_dev *pdev = container_of(dev, struct pci_dev, dev);
+ struct geos_gpio_attr *gattr = container_of(attr, struct geos_gpio_attr, attr);
+ struct solos_card *card = pci_get_drvdata(pdev);
+ uint32_t data32;
+
+ if (count != 1 && (count != 2 || buf[1] != '\n'))
+ return -EINVAL;
+
+ spin_lock_irq(&card->param_queue_lock);
+ data32 = ioread32(card->config_regs + GPIO_STATUS);
+ if (buf[0] == '1') {
+ data32 |= 1 << gattr->offset;
+ iowrite32(data32, card->config_regs + GPIO_STATUS);
+ } else if (buf[0] == '0') {
+ data32 &= ~(1 << gattr->offset);
+ iowrite32(data32, card->config_regs + GPIO_STATUS);
+ } else {
+ count = -EINVAL;
+ }
+ spin_lock_irq(&card->param_queue_lock);
+ return count;
+}
+
+static ssize_t geos_gpio_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct pci_dev *pdev = container_of(dev, struct pci_dev, dev);
+ struct geos_gpio_attr *gattr = container_of(attr, struct geos_gpio_attr, attr);
+ struct solos_card *card = pci_get_drvdata(pdev);
+ uint32_t data32;
+
+ data32 = ioread32(card->config_regs + GPIO_STATUS);
+ data32 = (data32 >> gattr->offset) & 1;
+
+ return sprintf(buf, "%d\n", data32);
+}
+
+static ssize_t hardware_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct pci_dev *pdev = container_of(dev, struct pci_dev, dev);
+ struct geos_gpio_attr *gattr = container_of(attr, struct geos_gpio_attr, attr);
+ struct solos_card *card = pci_get_drvdata(pdev);
+ uint32_t data32;
+
+ data32 = ioread32(card->config_regs + GPIO_STATUS);
+ switch (gattr->offset) {
+ case 0:
+ /* HardwareVersion */
+ data32 = data32 & 0x1F;
+ break;
+ case 1:
+ /* HardwareVariant */
+ data32 = (data32 >> 5) & 0x0F;
+ break;
+ }
+ return sprintf(buf, "%d\n", data32);
+}
+
static DEVICE_ATTR(console, 0644, console_show, console_store);
@@ -506,6 +579,14 @@ static DEVICE_ATTR(console, 0644, console_show, console_store);
#include "solos-attrlist.c"
+static SOLOS_GPIO_ATTR(GPIO1, 0644, geos_gpio_show, geos_gpio_store, 9);
+static SOLOS_GPIO_ATTR(GPIO2, 0644, geos_gpio_show, geos_gpio_store, 10);
+static SOLOS_GPIO_ATTR(GPIO3, 0644, geos_gpio_show, geos_gpio_store, 11);
+static SOLOS_GPIO_ATTR(GPIO4, 0644, geos_gpio_show, geos_gpio_store, 12);
+static SOLOS_GPIO_ATTR(GPIO5, 0644, geos_gpio_show, geos_gpio_store, 13);
+static SOLOS_GPIO_ATTR(PushButton, 0444, geos_gpio_show, NULL, 14);
+static SOLOS_GPIO_ATTR(HardwareVersion, 0444, hardware_show, NULL, 0);
+static SOLOS_GPIO_ATTR(HardwareVariant, 0444, hardware_show, NULL, 1);
#undef SOLOS_ATTR_RO
#undef SOLOS_ATTR_RW
@@ -522,6 +603,23 @@ static struct attribute_group solos_attr_group = {
.name = "parameters",
};
+static struct attribute *gpio_attrs[] = {
+ &gpio_attr_GPIO1.attr.attr,
+ &gpio_attr_GPIO2.attr.attr,
+ &gpio_attr_GPIO3.attr.attr,
+ &gpio_attr_GPIO4.attr.attr,
+ &gpio_attr_GPIO5.attr.attr,
+ &gpio_attr_PushButton.attr.attr,
+ &gpio_attr_HardwareVersion.attr.attr,
+ &gpio_attr_HardwareVariant.attr.attr,
+ NULL
+};
+
+static struct attribute_group gpio_attr_group = {
+ .attrs = gpio_attrs,
+ .name = "gpio",
+};
+
static int flash_upgrade(struct solos_card *card, int chip)
{
const struct firmware *fw;
@@ -1179,6 +1277,10 @@ static int fpga_probe(struct pci_dev *dev, const struct pci_device_id *id)
if (err)
goto out_free_irq;
+ if (card->fpga_version >= DMA_SUPPORTED &&
+ sysfs_create_group(&card->dev->dev.kobj, &gpio_attr_group))
+ dev_err(&card->dev->dev, "Could not register parameter group for GPIOs\n");
+
return 0;
out_free_irq:
@@ -1289,6 +1391,9 @@ static void fpga_remove(struct pci_dev *dev)
iowrite32(1, card->config_regs + FPGA_MODE);
(void)ioread32(card->config_regs + FPGA_MODE);
+ if (card->fpga_version >= DMA_SUPPORTED)
+ sysfs_remove_group(&card->dev->dev.kobj, &gpio_attr_group);
+
atm_remove(card);
free_irq(dev->irq, card);
--
1.8.0.1
next reply other threads:[~2012-12-19 21:01 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-12-19 21:01 David Woodhouse [this message]
2012-12-19 21:01 ` [PATCH 2/4] solos-pci: remove superfluous debug output David Woodhouse
2012-12-19 22:54 ` David Miller
2012-12-19 21:01 ` [PATCH 3/4] solos-pci: add firmware upgrade support for new models David Woodhouse
2012-12-19 22:54 ` David Miller
2012-12-19 21:01 ` [PATCH 4/4] solos-pci: ensure all TX packets are aligned to 4 bytes David Woodhouse
2012-12-19 22:54 ` David Miller
2012-12-19 22:54 ` [PATCH 1/4] solos-pci: add GPIO support for newer versions on Geos board David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1355950881-31550-1-git-send-email-dwmw2@infradead.org \
--to=dwmw2@infradead.org \
--cc=nathan@traverse.com.au \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).