* [PATCH net 1/2] bnx2x: Fix fastpath structures when memory allocation fails
2013-01-10 14:53 [PATCH net 0/2] bnx2x: bug fix patch series Yuval Mintz
@ 2013-01-10 14:53 ` Yuval Mintz
2013-01-10 14:53 ` [PATCH net 2/2] bnx2x: Allow management traffic after boot from SAN Yuval Mintz
2013-01-10 22:38 ` [PATCH net 0/2] bnx2x: bug fix patch series David Miller
2 siblings, 0 replies; 4+ messages in thread
From: Yuval Mintz @ 2013-01-10 14:53 UTC (permalink / raw)
To: davem, netdev; +Cc: eilong, ariele, Yuval Mintz
When allocating Tx queues, if for some reason
(e.g., lack of memory) allocation fails, driver will incorrectly
calculate the pointers of the various queues.
This patch repositions all pointers in such a case to point at
sequential structures in memory, allowing the bnx2x macros to
be used correctly when accessing them.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
---
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c | 30 +++++++++++++++++++++-
1 files changed, 28 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
index 01588b6..f771ddf 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
@@ -80,12 +80,37 @@ static inline void bnx2x_move_fp(struct bnx2x *bp, int from, int to)
new_txdata_index = new_max_eth_txqs + FCOE_TXQ_IDX_OFFSET;
}
- memcpy(&bp->bnx2x_txq[old_txdata_index],
- &bp->bnx2x_txq[new_txdata_index],
+ memcpy(&bp->bnx2x_txq[new_txdata_index],
+ &bp->bnx2x_txq[old_txdata_index],
sizeof(struct bnx2x_fp_txdata));
to_fp->txdata_ptr[0] = &bp->bnx2x_txq[new_txdata_index];
}
+/**
+ * bnx2x_shrink_eth_fp - guarantees fastpath structures stay intact
+ *
+ * @bp: driver handle
+ * @delta: number of eth queues which were not allocated
+ */
+static void bnx2x_shrink_eth_fp(struct bnx2x *bp, int delta)
+{
+ int i, cos, old_eth_num = BNX2X_NUM_ETH_QUEUES(bp);
+
+ /* Queue pointer cannot be re-set on an fp-basis, as moving pointer
+ * backward along the array could cause memory to be overriden
+ */
+ for (cos = 1; cos < bp->max_cos; cos++) {
+ for (i = 0; i < old_eth_num - delta; i++) {
+ struct bnx2x_fastpath *fp = &bp->fp[i];
+ int new_idx = cos * (old_eth_num - delta) + i;
+
+ memcpy(&bp->bnx2x_txq[new_idx], fp->txdata_ptr[cos],
+ sizeof(struct bnx2x_fp_txdata));
+ fp->txdata_ptr[cos] = &bp->bnx2x_txq[new_idx];
+ }
+ }
+}
+
int load_count[2][3] = { {0} }; /* per-path: 0-common, 1-port0, 2-port1 */
/* free skb in the packet ring at pos idx
@@ -3863,6 +3888,7 @@ int bnx2x_alloc_fp_mem(struct bnx2x *bp)
int delta = BNX2X_NUM_ETH_QUEUES(bp) - i;
WARN_ON(delta < 0);
+ bnx2x_shrink_eth_fp(bp, delta);
if (CNIC_SUPPORT(bp))
/* move non eth FPs next to last eth FP
* must be done in that order
--
1.7.1
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH net 2/2] bnx2x: Allow management traffic after boot from SAN
2013-01-10 14:53 [PATCH net 0/2] bnx2x: bug fix patch series Yuval Mintz
2013-01-10 14:53 ` [PATCH net 1/2] bnx2x: Fix fastpath structures when memory allocation fails Yuval Mintz
@ 2013-01-10 14:53 ` Yuval Mintz
2013-01-10 22:38 ` [PATCH net 0/2] bnx2x: bug fix patch series David Miller
2 siblings, 0 replies; 4+ messages in thread
From: Yuval Mintz @ 2013-01-10 14:53 UTC (permalink / raw)
To: davem, netdev; +Cc: eilong, ariele, Barak Witkowski, Yuval Mintz
From: Barak Witkowski <barak@broadcom.com>
As part of the previous driver unload flow, whenever bnx2x is
loaded after the UNDI driver it closes all Rx traffic.
However, this leads to management traffic also being stopped until
the network interface associated with one of its functions gets loaded.
To remedy this, management traffic is re-opened once the 'cleaning'
after the previous driver ends.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
---
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c | 60 +++++++++++++++++++---
1 files changed, 52 insertions(+), 8 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
index 940ef85..5523da3 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
@@ -127,6 +127,17 @@ MODULE_PARM_DESC(debug, " Default debug msglevel");
struct workqueue_struct *bnx2x_wq;
+struct bnx2x_mac_vals {
+ u32 xmac_addr;
+ u32 xmac_val;
+ u32 emac_addr;
+ u32 emac_val;
+ u32 umac_addr;
+ u32 umac_val;
+ u32 bmac_addr;
+ u32 bmac_val[2];
+};
+
enum bnx2x_board_type {
BCM57710 = 0,
BCM57711,
@@ -9420,12 +9431,19 @@ static inline void bnx2x_undi_int_disable(struct bnx2x *bp)
bnx2x_undi_int_disable_e1h(bp);
}
-static void bnx2x_prev_unload_close_mac(struct bnx2x *bp)
+static void bnx2x_prev_unload_close_mac(struct bnx2x *bp,
+ struct bnx2x_mac_vals *vals)
{
u32 val, base_addr, offset, mask, reset_reg;
bool mac_stopped = false;
u8 port = BP_PORT(bp);
+ /* reset addresses as they also mark which values were changed */
+ vals->bmac_addr = 0;
+ vals->umac_addr = 0;
+ vals->xmac_addr = 0;
+ vals->emac_addr = 0;
+
reset_reg = REG_RD(bp, MISC_REG_RESET_REG_2);
if (!CHIP_IS_E3(bp)) {
@@ -9447,14 +9465,18 @@ static void bnx2x_prev_unload_close_mac(struct bnx2x *bp)
*/
wb_data[0] = REG_RD(bp, base_addr + offset);
wb_data[1] = REG_RD(bp, base_addr + offset + 0x4);
+ vals->bmac_addr = base_addr + offset;
+ vals->bmac_val[0] = wb_data[0];
+ vals->bmac_val[1] = wb_data[1];
wb_data[0] &= ~BMAC_CONTROL_RX_ENABLE;
- REG_WR(bp, base_addr + offset, wb_data[0]);
- REG_WR(bp, base_addr + offset + 0x4, wb_data[1]);
+ REG_WR(bp, vals->bmac_addr, wb_data[0]);
+ REG_WR(bp, vals->bmac_addr + 0x4, wb_data[1]);
}
BNX2X_DEV_INFO("Disable emac Rx\n");
- REG_WR(bp, NIG_REG_NIG_EMAC0_EN + BP_PORT(bp)*4, 0);
-
+ vals->emac_addr = NIG_REG_NIG_EMAC0_EN + BP_PORT(bp)*4;
+ vals->emac_val = REG_RD(bp, vals->emac_addr);
+ REG_WR(bp, vals->emac_addr, 0);
mac_stopped = true;
} else {
if (reset_reg & MISC_REGISTERS_RESET_REG_2_XMAC) {
@@ -9465,14 +9487,18 @@ static void bnx2x_prev_unload_close_mac(struct bnx2x *bp)
val & ~(1 << 1));
REG_WR(bp, base_addr + XMAC_REG_PFC_CTRL_HI,
val | (1 << 1));
- REG_WR(bp, base_addr + XMAC_REG_CTRL, 0);
+ vals->xmac_addr = base_addr + XMAC_REG_CTRL;
+ vals->xmac_val = REG_RD(bp, vals->xmac_addr);
+ REG_WR(bp, vals->xmac_addr, 0);
mac_stopped = true;
}
mask = MISC_REGISTERS_RESET_REG_2_UMAC0 << port;
if (mask & reset_reg) {
BNX2X_DEV_INFO("Disable umac Rx\n");
base_addr = BP_PORT(bp) ? GRCBASE_UMAC1 : GRCBASE_UMAC0;
- REG_WR(bp, base_addr + UMAC_REG_COMMAND_CONFIG, 0);
+ vals->umac_addr = base_addr + UMAC_REG_COMMAND_CONFIG;
+ vals->umac_val = REG_RD(bp, vals->umac_addr);
+ REG_WR(bp, vals->umac_addr, 0);
mac_stopped = true;
}
}
@@ -9664,12 +9690,16 @@ static int bnx2x_prev_unload_common(struct bnx2x *bp)
{
u32 reset_reg, tmp_reg = 0, rc;
bool prev_undi = false;
+ struct bnx2x_mac_vals mac_vals;
+
/* It is possible a previous function received 'common' answer,
* but hasn't loaded yet, therefore creating a scenario of
* multiple functions receiving 'common' on the same path.
*/
BNX2X_DEV_INFO("Common unload Flow\n");
+ memset(&mac_vals, 0, sizeof(mac_vals));
+
if (bnx2x_prev_is_path_marked(bp))
return bnx2x_prev_mcp_done(bp);
@@ -9680,7 +9710,10 @@ static int bnx2x_prev_unload_common(struct bnx2x *bp)
u32 timer_count = 1000;
/* Close the MAC Rx to prevent BRB from filling up */
- bnx2x_prev_unload_close_mac(bp);
+ bnx2x_prev_unload_close_mac(bp, &mac_vals);
+
+ /* close LLH filters towards the BRB */
+ bnx2x_set_rx_filter(&bp->link_params, 0);
/* Check if the UNDI driver was previously loaded
* UNDI driver initializes CID offset for normal bell to 0x7
@@ -9727,6 +9760,17 @@ static int bnx2x_prev_unload_common(struct bnx2x *bp)
/* No packets are in the pipeline, path is ready for reset */
bnx2x_reset_common(bp);
+ if (mac_vals.xmac_addr)
+ REG_WR(bp, mac_vals.xmac_addr, mac_vals.xmac_val);
+ if (mac_vals.umac_addr)
+ REG_WR(bp, mac_vals.umac_addr, mac_vals.umac_val);
+ if (mac_vals.emac_addr)
+ REG_WR(bp, mac_vals.emac_addr, mac_vals.emac_val);
+ if (mac_vals.bmac_addr) {
+ REG_WR(bp, mac_vals.bmac_addr, mac_vals.bmac_val[0]);
+ REG_WR(bp, mac_vals.bmac_addr + 4, mac_vals.bmac_val[1]);
+ }
+
rc = bnx2x_prev_mark_path(bp, prev_undi);
if (rc) {
bnx2x_prev_mcp_done(bp);
--
1.7.1
^ permalink raw reply related [flat|nested] 4+ messages in thread