From: "Yuval Mintz" <yuvalmin@broadcom.com>
To: davem@davemloft.net, netdev@vger.kernel.org
Cc: eilong@broadcom.com, ariele@broadcom.com,
"Yuval Mintz" <yuvalmin@broadcom.com>
Subject: [PATCH net-next 07/10] bnx2x: improve stop-on-error
Date: Mon, 14 Jan 2013 17:11:47 +0200 [thread overview]
Message-ID: <1358176310-31504-8-git-send-email-yuvalmin@broadcom.com> (raw)
In-Reply-To: <1358176310-31504-1-git-send-email-yuvalmin@broadcom.com>
Get better control over interrupts during panic, and allow FW to
test outgoing Tx packets when stop-on-error is allowed.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
---
drivers/net/ethernet/broadcom/bnx2x/bnx2x.h | 6 +-
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c | 4 +
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h | 2 +-
.../net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c | 4 -
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c | 139 +++++++++++----------
5 files changed, 79 insertions(+), 76 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
index 309bbb7..757fe2c 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
@@ -123,20 +123,18 @@ do { \
} while (0)
#ifdef BNX2X_STOP_ON_ERROR
-void bnx2x_int_disable(struct bnx2x *bp);
#define bnx2x_panic() \
do { \
bp->panic = 1; \
BNX2X_ERR("driver assert\n"); \
- bnx2x_int_disable(bp); \
- bnx2x_panic_dump(bp); \
+ bnx2x_panic_dump(bp, true); \
} while (0)
#else
#define bnx2x_panic() \
do { \
bp->panic = 1; \
BNX2X_ERR("driver assert\n"); \
- bnx2x_panic_dump(bp); \
+ bnx2x_panic_dump(bp, false); \
} while (0)
#endif
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
index 00706c4..53a2c0e 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
@@ -3510,13 +3510,17 @@ netdev_tx_t bnx2x_start_xmit(struct sk_buff *skb, struct net_device *dev)
/* when transmitting in a vf, start bd must hold the ethertype
* for fw to enforce it
*/
+#ifndef BNX2X_STOP_ON_ERROR
if (IS_VF(bp)) {
+#endif
tx_start_bd->vlan_or_ethertype =
cpu_to_le16(ntohs(eth->h_proto));
+#ifndef BNX2X_STOP_ON_ERROR
} else {
/* used by FW for packet accounting */
tx_start_bd->vlan_or_ethertype = cpu_to_le16(pkt_prod);
}
+#endif
}
/* turn on parsing and get a BD */
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h
index a2583f2..8104b98 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h
@@ -479,7 +479,7 @@ int bnx2x_set_power_state(struct bnx2x *bp, pci_power_t state);
*/
void bnx2x_update_max_mf_config(struct bnx2x *bp, u32 value);
/* Error handling */
-void bnx2x_panic_dump(struct bnx2x *bp);
+void bnx2x_panic_dump(struct bnx2x *bp, bool disable_int);
void bnx2x_fw_dump_lvl(struct bnx2x *bp, const char *lvl);
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
index db9ff98..53374de 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
@@ -2720,10 +2720,6 @@ static void bnx2x_self_test(struct net_device *dev,
buf[2] = 1;
etest->flags |= ETH_TEST_FL_FAILED;
}
-
-#ifdef BNX2X_EXTRA_DEBUG
- bnx2x_panic_dump(bp);
-#endif
}
#define IS_PORT_STAT(i) \
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
index 3b05184..b75049e 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
@@ -791,7 +791,71 @@ static void bnx2x_fw_dump(struct bnx2x *bp)
bnx2x_fw_dump_lvl(bp, KERN_ERR);
}
-void bnx2x_panic_dump(struct bnx2x *bp)
+static void bnx2x_hc_int_disable(struct bnx2x *bp)
+{
+ int port = BP_PORT(bp);
+ u32 addr = port ? HC_REG_CONFIG_1 : HC_REG_CONFIG_0;
+ u32 val = REG_RD(bp, addr);
+
+ /* in E1 we must use only PCI configuration space to disable
+ * MSI/MSIX capablility
+ * It's forbitten to disable IGU_PF_CONF_MSI_MSIX_EN in HC block
+ */
+ if (CHIP_IS_E1(bp)) {
+ /* Since IGU_PF_CONF_MSI_MSIX_EN still always on
+ * Use mask register to prevent from HC sending interrupts
+ * after we exit the function
+ */
+ REG_WR(bp, HC_REG_INT_MASK + port*4, 0);
+
+ val &= ~(HC_CONFIG_0_REG_SINGLE_ISR_EN_0 |
+ HC_CONFIG_0_REG_INT_LINE_EN_0 |
+ HC_CONFIG_0_REG_ATTN_BIT_EN_0);
+ } else
+ val &= ~(HC_CONFIG_0_REG_SINGLE_ISR_EN_0 |
+ HC_CONFIG_0_REG_MSI_MSIX_INT_EN_0 |
+ HC_CONFIG_0_REG_INT_LINE_EN_0 |
+ HC_CONFIG_0_REG_ATTN_BIT_EN_0);
+
+ DP(NETIF_MSG_IFDOWN,
+ "write %x to HC %d (addr 0x%x)\n",
+ val, port, addr);
+
+ /* flush all outstanding writes */
+ mmiowb();
+
+ REG_WR(bp, addr, val);
+ if (REG_RD(bp, addr) != val)
+ BNX2X_ERR("BUG! proper val not read from IGU!\n");
+}
+
+static void bnx2x_igu_int_disable(struct bnx2x *bp)
+{
+ u32 val = REG_RD(bp, IGU_REG_PF_CONFIGURATION);
+
+ val &= ~(IGU_PF_CONF_MSI_MSIX_EN |
+ IGU_PF_CONF_INT_LINE_EN |
+ IGU_PF_CONF_ATTN_BIT_EN);
+
+ DP(NETIF_MSG_IFDOWN, "write %x to IGU\n", val);
+
+ /* flush all outstanding writes */
+ mmiowb();
+
+ REG_WR(bp, IGU_REG_PF_CONFIGURATION, val);
+ if (REG_RD(bp, IGU_REG_PF_CONFIGURATION) != val)
+ BNX2X_ERR("BUG! proper val not read from IGU!\n");
+}
+
+static void bnx2x_int_disable(struct bnx2x *bp)
+{
+ if (bp->common.int_block == INT_BLOCK_HC)
+ bnx2x_hc_int_disable(bp);
+ else
+ bnx2x_igu_int_disable(bp);
+}
+
+void bnx2x_panic_dump(struct bnx2x *bp, bool disable_int)
{
int i;
u16 j;
@@ -801,6 +865,8 @@ void bnx2x_panic_dump(struct bnx2x *bp)
u16 start = 0, end = 0;
u8 cos;
#endif
+ if (disable_int)
+ bnx2x_int_disable(bp);
bp->stats_state = STATS_STATE_DISABLED;
bp->eth_stats.unrecoverable_error++;
@@ -1516,71 +1582,6 @@ void bnx2x_int_enable(struct bnx2x *bp)
bnx2x_igu_int_enable(bp);
}
-static void bnx2x_hc_int_disable(struct bnx2x *bp)
-{
- int port = BP_PORT(bp);
- u32 addr = port ? HC_REG_CONFIG_1 : HC_REG_CONFIG_0;
- u32 val = REG_RD(bp, addr);
-
- /*
- * in E1 we must use only PCI configuration space to disable
- * MSI/MSIX capablility
- * It's forbitten to disable IGU_PF_CONF_MSI_MSIX_EN in HC block
- */
- if (CHIP_IS_E1(bp)) {
- /* Since IGU_PF_CONF_MSI_MSIX_EN still always on
- * Use mask register to prevent from HC sending interrupts
- * after we exit the function
- */
- REG_WR(bp, HC_REG_INT_MASK + port*4, 0);
-
- val &= ~(HC_CONFIG_0_REG_SINGLE_ISR_EN_0 |
- HC_CONFIG_0_REG_INT_LINE_EN_0 |
- HC_CONFIG_0_REG_ATTN_BIT_EN_0);
- } else
- val &= ~(HC_CONFIG_0_REG_SINGLE_ISR_EN_0 |
- HC_CONFIG_0_REG_MSI_MSIX_INT_EN_0 |
- HC_CONFIG_0_REG_INT_LINE_EN_0 |
- HC_CONFIG_0_REG_ATTN_BIT_EN_0);
-
- DP(NETIF_MSG_IFDOWN,
- "write %x to HC %d (addr 0x%x)\n",
- val, port, addr);
-
- /* flush all outstanding writes */
- mmiowb();
-
- REG_WR(bp, addr, val);
- if (REG_RD(bp, addr) != val)
- BNX2X_ERR("BUG! proper val not read from IGU!\n");
-}
-
-static void bnx2x_igu_int_disable(struct bnx2x *bp)
-{
- u32 val = REG_RD(bp, IGU_REG_PF_CONFIGURATION);
-
- val &= ~(IGU_PF_CONF_MSI_MSIX_EN |
- IGU_PF_CONF_INT_LINE_EN |
- IGU_PF_CONF_ATTN_BIT_EN);
-
- DP(NETIF_MSG_IFDOWN, "write %x to IGU\n", val);
-
- /* flush all outstanding writes */
- mmiowb();
-
- REG_WR(bp, IGU_REG_PF_CONFIGURATION, val);
- if (REG_RD(bp, IGU_REG_PF_CONFIGURATION) != val)
- BNX2X_ERR("BUG! proper val not read from IGU!\n");
-}
-
-static void bnx2x_int_disable(struct bnx2x *bp)
-{
- if (bp->common.int_block == INT_BLOCK_HC)
- bnx2x_hc_int_disable(bp);
- else
- bnx2x_igu_int_disable(bp);
-}
-
void bnx2x_int_disable_sync(struct bnx2x *bp, int disable_hw)
{
int msix = (bp->flags & USING_MSIX_FLAG) ? 1 : 0;
@@ -2934,6 +2935,10 @@ static unsigned long bnx2x_get_common_flags(struct bnx2x *bp,
__set_bit(BNX2X_Q_FLG_ZERO_STATS, &flags);
+#ifdef BNX2X_STOP_ON_ERROR
+ __set_bit(BNX2X_Q_FLG_TX_SEC, &flags);
+#endif
+
return flags;
}
@@ -4754,7 +4759,7 @@ static int bnx2x_cnic_handle_cfc_del(struct bnx2x *bp, u32 cid,
BNX2X_ERR("got delete ramrod for CNIC CID %d with error!\n",
cid);
- bnx2x_panic_dump(bp);
+ bnx2x_panic_dump(bp, false);
}
bnx2x_cnic_cfc_comp(bp, cid, err);
return 0;
--
1.8.1.227.g44fe835
next prev parent reply other threads:[~2013-01-14 16:10 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-01-14 15:11 [PATCH net-next 0/10] bnx2x: patch series Yuval Mintz
2013-01-14 15:11 ` [PATCH net-next 01/10] bnx2x: Clear dirty status when booting after UNDI Yuval Mintz
2013-01-14 15:11 ` [PATCH net-next 02/10] bnx2x: Add an additional fatal hw assertion - BRB_HW_INTERRUPT Yuval Mintz
2013-01-14 15:11 ` [PATCH net-next 03/10] bnx2x: use SAN Mac for FCoE Yuval Mintz
2013-01-14 15:11 ` [PATCH net-next 04/10] bnx2x: Fix rare self-test failures Yuval Mintz
2013-01-14 15:11 ` [PATCH net-next 05/10] bnx2x: Added nvram personalities support Yuval Mintz
2013-01-14 15:11 ` [PATCH net-next 06/10] bnx2x: add `ethtool -w' support Yuval Mintz
2013-01-14 15:11 ` Yuval Mintz [this message]
2013-01-14 15:11 ` [PATCH net-next 08/10] bnx2x: Clean previous IGU status before ack Yuval Mintz
2013-01-14 15:11 ` [PATCH net-next 09/10] bnx2x: Added FW GRO bridging support Yuval Mintz
2013-01-14 17:22 ` Eric Dumazet
2013-01-14 18:44 ` Eric Dumazet
2013-01-15 7:28 ` Yuval Mintz
2013-01-15 14:39 ` Eric Dumazet
2013-01-15 14:02 ` Yuval Mintz
2013-01-15 15:07 ` Eric Dumazet
2013-01-15 20:09 ` David Miller
2013-01-16 4:56 ` Eric Dumazet
2013-01-16 5:37 ` [PATCH net-next] bnx2x: fix GRO parameters Eric Dumazet
2013-01-16 7:01 ` Yuval Mintz
2013-01-16 15:29 ` Eric Dumazet
2013-01-16 14:38 ` Yuval Mintz
2013-01-16 16:50 ` Eric Dumazet
2013-01-17 7:16 ` Yuval Mintz
2013-01-14 15:11 ` [PATCH net-next 10/10] bnx2x: Introduce 2013 and advance version to 1.78.02 Yuval Mintz
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1358176310-31504-8-git-send-email-yuvalmin@broadcom.com \
--to=yuvalmin@broadcom.com \
--cc=ariele@broadcom.com \
--cc=davem@davemloft.net \
--cc=eilong@broadcom.com \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).