* [PATCH net-next 00/06] bnx2x: net-next patch series
@ 2013-03-27 11:05 Yuval Mintz
2013-03-27 11:05 ` [PATCH net-next 1/6] bnx2x: missing ARI should not be lethal Yuval Mintz
` (6 more replies)
0 siblings, 7 replies; 8+ messages in thread
From: Yuval Mintz @ 2013-03-27 11:05 UTC (permalink / raw)
To: davem, netdev; +Cc: eilong, ariele, Yuval Mintz
Hi Dave,
This patch series mostly contains patches correcting the
behaviour of VFs - preventing races, correcting VFs' statistics,
etc.
It also enhances bnx2x's `ethtool -m' command.
Please consider applying these patches to 'net-next'.
Thanks,
Yuval Mintz
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH net-next 1/6] bnx2x: missing ARI should not be lethal
2013-03-27 11:05 [PATCH net-next 00/06] bnx2x: net-next patch series Yuval Mintz
@ 2013-03-27 11:05 ` Yuval Mintz
2013-03-27 11:05 ` [PATCH net-next 2/6] bnx2x: Fix VF statistics Yuval Mintz
` (5 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: Yuval Mintz @ 2013-03-27 11:05 UTC (permalink / raw)
To: davem, netdev; +Cc: eilong, ariele, Yuval Mintz
From: Ariel Elior <ariele@broadcom.com>
If ARI forwarding flag is missing from the PCI bridge, remove SR-IOV
support instead of failing the probe process.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
---
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c | 10 ++++++----
1 file changed, 6 insertions(+), 4 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c
index faadd15..ad7ad1d 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c
@@ -1932,20 +1932,22 @@ int bnx2x_iov_init_one(struct bnx2x *bp, int int_mode_param,
/* SRIOV can be enabled only with MSIX */
if (int_mode_param == BNX2X_INT_MODE_MSI ||
- int_mode_param == BNX2X_INT_MODE_INTX)
+ int_mode_param == BNX2X_INT_MODE_INTX) {
BNX2X_ERR("Forced MSI/INTx mode is incompatible with SRIOV\n");
+ return 0;
+ }
err = -EIO;
/* verify ari is enabled */
if (!bnx2x_ari_enabled(bp->pdev)) {
- BNX2X_ERR("ARI not supported, SRIOV can not be enabled\n");
- return err;
+ BNX2X_ERR("ARI not supported (check pci bridge ARI forwarding), SRIOV can not be enabled\n");
+ return 0;
}
/* verify igu is in normal mode */
if (CHIP_INT_MODE_IS_BC(bp)) {
BNX2X_ERR("IGU not normal mode, SRIOV can not be enabled\n");
- return err;
+ return 0;
}
/* allocate the vfs database */
--
1.8.1.227.g44fe835
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH net-next 2/6] bnx2x: Fix VF statistics
2013-03-27 11:05 [PATCH net-next 00/06] bnx2x: net-next patch series Yuval Mintz
2013-03-27 11:05 ` [PATCH net-next 1/6] bnx2x: missing ARI should not be lethal Yuval Mintz
@ 2013-03-27 11:05 ` Yuval Mintz
2013-03-27 11:05 ` [PATCH net-next 3/6] bnx2x: Fix VF outer vlan removal Yuval Mintz
` (4 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: Yuval Mintz @ 2013-03-27 11:05 UTC (permalink / raw)
To: davem, netdev; +Cc: eilong, ariele, Yuval Mintz
From: Ariel Elior <ariele@broadcom.com>
After a VF performs load/unload its statistics become corrupt -
we now zero the statistics structures upon a VF device load.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
---
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c | 5 +-
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c | 77 +++++++++++++----------
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.h | 2 +-
3 files changed, 47 insertions(+), 37 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
index 10b0748..cf2a169 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
@@ -6040,9 +6040,10 @@ void bnx2x_nic_init(struct bnx2x *bp, u32 load_code)
rmb();
bnx2x_init_rx_rings(bp);
bnx2x_init_tx_rings(bp);
-
- if (IS_VF(bp))
+ if (IS_VF(bp)) {
+ bnx2x_memset_stats(bp);
return;
+ }
/* Initialize MOD_ABS interrupts */
bnx2x_init_mod_abs_int(bp, &bp->link_vars, bp->common.chip_id,
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c
index 4397f8b..2ca3d94 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c
@@ -1547,11 +1547,51 @@ static void bnx2x_prep_fw_stats_req(struct bnx2x *bp)
}
}
+void bnx2x_memset_stats(struct bnx2x *bp)
+{
+ int i;
+
+ /* function stats */
+ for_each_queue(bp, i) {
+ struct bnx2x_fp_stats *fp_stats = &bp->fp_stats[i];
+
+ memset(&fp_stats->old_tclient, 0,
+ sizeof(fp_stats->old_tclient));
+ memset(&fp_stats->old_uclient, 0,
+ sizeof(fp_stats->old_uclient));
+ memset(&fp_stats->old_xclient, 0,
+ sizeof(fp_stats->old_xclient));
+ if (bp->stats_init) {
+ memset(&fp_stats->eth_q_stats, 0,
+ sizeof(fp_stats->eth_q_stats));
+ memset(&fp_stats->eth_q_stats_old, 0,
+ sizeof(fp_stats->eth_q_stats_old));
+ }
+ }
+
+ memset(&bp->dev->stats, 0, sizeof(bp->dev->stats));
+
+ if (bp->stats_init) {
+ memset(&bp->net_stats_old, 0, sizeof(bp->net_stats_old));
+ memset(&bp->fw_stats_old, 0, sizeof(bp->fw_stats_old));
+ memset(&bp->eth_stats_old, 0, sizeof(bp->eth_stats_old));
+ memset(&bp->eth_stats, 0, sizeof(bp->eth_stats));
+ memset(&bp->func_stats, 0, sizeof(bp->func_stats));
+ }
+
+ bp->stats_state = STATS_STATE_DISABLED;
+
+ if (bp->port.pmf && bp->port.port_stx)
+ bnx2x_port_stats_base_init(bp);
+
+ /* mark the end of statistics initializiation */
+ bp->stats_init = false;
+}
+
void bnx2x_stats_init(struct bnx2x *bp)
{
int /*abs*/port = BP_PORT(bp);
int mb_idx = BP_FW_MB_IDX(bp);
- int i;
bp->stats_pending = 0;
bp->executer_idx = 0;
@@ -1587,36 +1627,11 @@ void bnx2x_stats_init(struct bnx2x *bp)
&(bp->port.old_nig_stats.egress_mac_pkt1_lo), 2);
}
- /* function stats */
- for_each_queue(bp, i) {
- struct bnx2x_fp_stats *fp_stats = &bp->fp_stats[i];
-
- memset(&fp_stats->old_tclient, 0,
- sizeof(fp_stats->old_tclient));
- memset(&fp_stats->old_uclient, 0,
- sizeof(fp_stats->old_uclient));
- memset(&fp_stats->old_xclient, 0,
- sizeof(fp_stats->old_xclient));
- if (bp->stats_init) {
- memset(&fp_stats->eth_q_stats, 0,
- sizeof(fp_stats->eth_q_stats));
- memset(&fp_stats->eth_q_stats_old, 0,
- sizeof(fp_stats->eth_q_stats_old));
- }
- }
-
/* Prepare statistics ramrod data */
bnx2x_prep_fw_stats_req(bp);
- memset(&bp->dev->stats, 0, sizeof(bp->dev->stats));
+ /* Clean SP from previous statistics */
if (bp->stats_init) {
- memset(&bp->net_stats_old, 0, sizeof(bp->net_stats_old));
- memset(&bp->fw_stats_old, 0, sizeof(bp->fw_stats_old));
- memset(&bp->eth_stats_old, 0, sizeof(bp->eth_stats_old));
- memset(&bp->eth_stats, 0, sizeof(bp->eth_stats));
- memset(&bp->func_stats, 0, sizeof(bp->func_stats));
-
- /* Clean SP from previous statistics */
if (bp->func_stx) {
memset(bnx2x_sp(bp, func_stats), 0,
sizeof(struct host_func_stats));
@@ -1626,13 +1641,7 @@ void bnx2x_stats_init(struct bnx2x *bp)
}
}
- bp->stats_state = STATS_STATE_DISABLED;
-
- if (bp->port.pmf && bp->port.port_stx)
- bnx2x_port_stats_base_init(bp);
-
- /* mark the end of statistics initializiation */
- bp->stats_init = false;
+ bnx2x_memset_stats(bp);
}
void bnx2x_save_statistics(struct bnx2x *bp)
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.h
index 198f6f1..d117f47 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.h
@@ -540,8 +540,8 @@ struct bnx2x_fw_port_stats_old {
/* forward */
struct bnx2x;
+void bnx2x_memset_stats(struct bnx2x *bp);
void bnx2x_stats_init(struct bnx2x *bp);
-
void bnx2x_stats_handle(struct bnx2x *bp, enum bnx2x_stats_event event);
/**
--
1.8.1.227.g44fe835
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH net-next 3/6] bnx2x: Fix VF outer vlan removal
2013-03-27 11:05 [PATCH net-next 00/06] bnx2x: net-next patch series Yuval Mintz
2013-03-27 11:05 ` [PATCH net-next 1/6] bnx2x: missing ARI should not be lethal Yuval Mintz
2013-03-27 11:05 ` [PATCH net-next 2/6] bnx2x: Fix VF statistics Yuval Mintz
@ 2013-03-27 11:05 ` Yuval Mintz
2013-03-27 11:05 ` [PATCH net-next 4/6] bnx2x: Prevent VF race Yuval Mintz
` (3 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: Yuval Mintz @ 2013-03-27 11:05 UTC (permalink / raw)
To: davem, netdev; +Cc: eilong, ariele, Yuval Mintz
From: Ariel Elior <ariele@broadcom.com>
Outer vlan removal in VF queues was made according to the VF's
multi-function mode (which is never set).
Instead, the PF's multi-function mode should be used to determine
if outer vlan removal is needed.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
---
drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c | 17 +++++++++--------
1 file changed, 9 insertions(+), 8 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c
index 531eebf..5d59070 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c
@@ -435,7 +435,6 @@ int bnx2x_vfpf_setup_q(struct bnx2x *bp, int fp_idx)
/* calculate queue flags */
flags |= VFPF_QUEUE_FLG_STATS;
flags |= VFPF_QUEUE_FLG_CACHE_ALIGN;
- flags |= IS_MF_SD(bp) ? VFPF_QUEUE_FLG_OV : 0;
flags |= VFPF_QUEUE_FLG_VLAN;
DP(NETIF_MSG_IFUP, "vlan removal enabled\n");
@@ -1004,7 +1003,7 @@ static void bnx2x_vf_mbx_init_vf(struct bnx2x *bp, struct bnx2x_virtf *vf,
}
/* convert MBX queue-flags to standard SP queue-flags */
-static void bnx2x_vf_mbx_set_q_flags(u32 mbx_q_flags,
+static void bnx2x_vf_mbx_set_q_flags(struct bnx2x *bp, u32 mbx_q_flags,
unsigned long *sp_q_flags)
{
if (mbx_q_flags & VFPF_QUEUE_FLG_TPA)
@@ -1015,8 +1014,6 @@ static void bnx2x_vf_mbx_set_q_flags(u32 mbx_q_flags,
__set_bit(BNX2X_Q_FLG_TPA_GRO, sp_q_flags);
if (mbx_q_flags & VFPF_QUEUE_FLG_STATS)
__set_bit(BNX2X_Q_FLG_STATS, sp_q_flags);
- if (mbx_q_flags & VFPF_QUEUE_FLG_OV)
- __set_bit(BNX2X_Q_FLG_OV, sp_q_flags);
if (mbx_q_flags & VFPF_QUEUE_FLG_VLAN)
__set_bit(BNX2X_Q_FLG_VLAN, sp_q_flags);
if (mbx_q_flags & VFPF_QUEUE_FLG_COS)
@@ -1025,6 +1022,10 @@ static void bnx2x_vf_mbx_set_q_flags(u32 mbx_q_flags,
__set_bit(BNX2X_Q_FLG_HC, sp_q_flags);
if (mbx_q_flags & VFPF_QUEUE_FLG_DHC)
__set_bit(BNX2X_Q_FLG_DHC, sp_q_flags);
+
+ /* outer vlan removal is set according to the PF's multi fuction mode */
+ if (IS_MF_SD(bp))
+ __set_bit(BNX2X_Q_FLG_OV, sp_q_flags);
}
static void bnx2x_vf_mbx_setup_q(struct bnx2x *bp, struct bnx2x_virtf *vf,
@@ -1075,11 +1076,11 @@ static void bnx2x_vf_mbx_setup_q(struct bnx2x *bp, struct bnx2x_virtf *vf,
init_p->tx.hc_rate = setup_q->txq.hc_rate;
init_p->tx.sb_cq_index = setup_q->txq.sb_index;
- bnx2x_vf_mbx_set_q_flags(setup_q->txq.flags,
+ bnx2x_vf_mbx_set_q_flags(bp, setup_q->txq.flags,
&init_p->tx.flags);
/* tx setup - flags */
- bnx2x_vf_mbx_set_q_flags(setup_q->txq.flags,
+ bnx2x_vf_mbx_set_q_flags(bp, setup_q->txq.flags,
&setup_p->flags);
/* tx setup - general, nothing */
@@ -1107,11 +1108,11 @@ static void bnx2x_vf_mbx_setup_q(struct bnx2x *bp, struct bnx2x_virtf *vf,
/* rx init */
init_p->rx.hc_rate = setup_q->rxq.hc_rate;
init_p->rx.sb_cq_index = setup_q->rxq.sb_index;
- bnx2x_vf_mbx_set_q_flags(setup_q->rxq.flags,
+ bnx2x_vf_mbx_set_q_flags(bp, setup_q->rxq.flags,
&init_p->rx.flags);
/* rx setup - flags */
- bnx2x_vf_mbx_set_q_flags(setup_q->rxq.flags,
+ bnx2x_vf_mbx_set_q_flags(bp, setup_q->rxq.flags,
&setup_p->flags);
/* rx setup - general */
--
1.8.1.227.g44fe835
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH net-next 4/6] bnx2x: Prevent VF race
2013-03-27 11:05 [PATCH net-next 00/06] bnx2x: net-next patch series Yuval Mintz
` (2 preceding siblings ...)
2013-03-27 11:05 ` [PATCH net-next 3/6] bnx2x: Fix VF outer vlan removal Yuval Mintz
@ 2013-03-27 11:05 ` Yuval Mintz
2013-03-27 11:05 ` [PATCH net-next 5/6] bnx2x: Support reading I2C EEPROM SFF8472 Yuval Mintz
` (2 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: Yuval Mintz @ 2013-03-27 11:05 UTC (permalink / raw)
To: davem, netdev; +Cc: eilong, ariele, Dmitry Kravkov, Yuval Mintz
From: Dmitry Kravkov <dmitry@broadcom.com>
The mail box containing the Vf-Pf messages is susceptible
to a race - it's possible for 2 flows to try and write commands,
causing one to override the other's message.
Use a mutex to synchronize the access, preventing said race.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
---
drivers/net/ethernet/broadcom/bnx2x/bnx2x.h | 2 +
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c | 3 +-
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c | 12 +--
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h | 9 ++-
drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c | 90 ++++++++++++++++-------
5 files changed, 82 insertions(+), 34 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
index c59da2d..c630342 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
@@ -1277,6 +1277,8 @@ struct bnx2x {
#define BP_FW_MB_IDX(bp) BP_FW_MB_IDX_VN(bp, BP_VN(bp))
#ifdef CONFIG_BNX2X_SRIOV
+ /* protects vf2pf mailbox from simultaneous access */
+ struct mutex vf2pf_mutex;
/* vf pf channel mailbox contains request and response buffers */
struct bnx2x_vf_mbx_msg *vf2pf_mbox;
dma_addr_t vf2pf_mbox_mapping;
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
index 2c6a2a6..6de18d7 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
@@ -12520,7 +12520,8 @@ static int bnx2x_init_one(struct pci_dev *pdev,
* l2 connections.
*/
if (IS_VF(bp)) {
- bnx2x_vf_map_doorbells(bp);
+ bp->doorbells = bnx2x_vf_doorbells(bp);
+ mutex_init(&bp->vf2pf_mutex);
rc = bnx2x_vf_pci_alloc(bp);
if (rc)
goto init_one_exit;
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c
index faadd15..0431b98 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c
@@ -2386,8 +2386,8 @@ int bnx2x_iov_eq_sp_event(struct bnx2x *bp, union event_ring_elem *elem)
goto get_vf;
case EVENT_RING_OPCODE_MALICIOUS_VF:
abs_vfid = elem->message.data.malicious_vf_event.vf_id;
- DP(BNX2X_MSG_IOV, "Got VF MALICIOUS notification abs_vfid=%d\n",
- abs_vfid);
+ DP(BNX2X_MSG_IOV, "Got VF MALICIOUS notification abs_vfid=%d err_id=0x%x\n",
+ abs_vfid, elem->message.data.malicious_vf_event.err_id);
goto get_vf;
default:
return 1;
@@ -2444,8 +2444,8 @@ get_vf:
/* Do nothing for now */
break;
case EVENT_RING_OPCODE_MALICIOUS_VF:
- DP(BNX2X_MSG_IOV, "got VF [%d] MALICIOUS notification\n",
- vf->abs_vfid);
+ DP(BNX2X_MSG_IOV, "Got VF MALICIOUS notification abs_vfid=%d error id %x\n",
+ abs_vfid, elem->message.data.malicious_vf_event.err_id);
/* Do nothing for now */
break;
}
@@ -3415,10 +3415,10 @@ enum sample_bulletin_result bnx2x_sample_bulletin(struct bnx2x *bp)
return PFVF_BULLETIN_UPDATED;
}
-void bnx2x_vf_map_doorbells(struct bnx2x *bp)
+void __iomem *bnx2x_vf_doorbells(struct bnx2x *bp)
{
/* vf doorbells are embedded within the regview */
- bp->doorbells = bp->regview + PXP_VF_ADDR_DB_START;
+ return bp->regview + PXP_VF_ADDR_DB_START;
}
int bnx2x_vf_pci_alloc(struct bnx2x *bp)
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h
index a10bdb2..d4b17b7 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h
@@ -713,6 +713,7 @@ void bnx2x_add_tlv(struct bnx2x *bp, void *tlvs_list, u16 offset, u16 type,
u16 length);
void bnx2x_vfpf_prep(struct bnx2x *bp, struct vfpf_first_tlv *first_tlv,
u16 type, u16 length);
+void bnx2x_vfpf_finalize(struct bnx2x *bp, struct vfpf_first_tlv *first_tlv);
void bnx2x_dp_tlv_list(struct bnx2x *bp, void *tlvs_list);
bool bnx2x_tlv_supported(u16 tlvtype);
@@ -751,7 +752,7 @@ static inline int bnx2x_vf_ustorm_prods_offset(struct bnx2x *bp,
}
enum sample_bulletin_result bnx2x_sample_bulletin(struct bnx2x *bp);
-void bnx2x_vf_map_doorbells(struct bnx2x *bp);
+void __iomem *bnx2x_vf_doorbells(struct bnx2x *bp);
int bnx2x_vf_pci_alloc(struct bnx2x *bp);
int bnx2x_enable_sriov(struct bnx2x *bp);
void bnx2x_disable_sriov(struct bnx2x *bp);
@@ -808,7 +809,11 @@ static inline enum sample_bulletin_result bnx2x_sample_bulletin(struct bnx2x *bp
return PFVF_BULLETIN_UNCHANGED;
}
-static inline int bnx2x_vf_map_doorbells(struct bnx2x *bp) {return 0; }
+static inline void __iomem *bnx2x_vf_doorbells(struct bnx2x *bp)
+{
+ return NULL;
+}
+
static inline int bnx2x_vf_pci_alloc(struct bnx2x *bp) {return 0; }
static inline void bnx2x_pf_set_vfs_vlan(struct bnx2x *bp) {}
static inline int bnx2x_sriov_configure(struct pci_dev *dev, int num_vfs) {return 0; }
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c
index 531eebf..46f9843 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c
@@ -36,6 +36,8 @@ void bnx2x_add_tlv(struct bnx2x *bp, void *tlvs_list, u16 offset, u16 type,
void bnx2x_vfpf_prep(struct bnx2x *bp, struct vfpf_first_tlv *first_tlv,
u16 type, u16 length)
{
+ mutex_lock(&bp->vf2pf_mutex);
+
DP(BNX2X_MSG_IOV, "preparing to send %d tlv over vf pf channel\n",
type);
@@ -49,6 +51,15 @@ void bnx2x_vfpf_prep(struct bnx2x *bp, struct vfpf_first_tlv *first_tlv,
first_tlv->resp_msg_offset = sizeof(bp->vf2pf_mbox->req);
}
+/* releases the mailbox */
+void bnx2x_vfpf_finalize(struct bnx2x *bp, struct vfpf_first_tlv *first_tlv)
+{
+ DP(BNX2X_MSG_IOV, "done sending [%d] tlv over vf pf channel\n",
+ first_tlv->tl.type);
+
+ mutex_unlock(&bp->vf2pf_mutex);
+}
+
/* list the types and lengths of the tlvs on the buffer */
void bnx2x_dp_tlv_list(struct bnx2x *bp, void *tlvs_list)
{
@@ -181,8 +192,10 @@ int bnx2x_vfpf_acquire(struct bnx2x *bp, u8 tx_count, u8 rx_count)
/* clear mailbox and prep first tlv */
bnx2x_vfpf_prep(bp, &req->first_tlv, CHANNEL_TLV_ACQUIRE, sizeof(*req));
- if (bnx2x_get_vf_id(bp, &vf_id))
- return -EAGAIN;
+ if (bnx2x_get_vf_id(bp, &vf_id)) {
+ rc = -EAGAIN;
+ goto out;
+ }
req->vfdev_info.vf_id = vf_id;
req->vfdev_info.vf_os = 0;
@@ -213,7 +226,7 @@ int bnx2x_vfpf_acquire(struct bnx2x *bp, u8 tx_count, u8 rx_count)
/* PF timeout */
if (rc)
- return rc;
+ goto out;
/* copy acquire response from buffer to bp */
memcpy(&bp->acquire_resp, resp, sizeof(bp->acquire_resp));
@@ -253,7 +266,8 @@ int bnx2x_vfpf_acquire(struct bnx2x *bp, u8 tx_count, u8 rx_count)
/* PF reports error */
BNX2X_ERR("Failed to get the requested amount of resources: %d. Breaking...\n",
bp->acquire_resp.hdr.status);
- return -EAGAIN;
+ rc = -EAGAIN;
+ goto out;
}
}
@@ -279,20 +293,24 @@ int bnx2x_vfpf_acquire(struct bnx2x *bp, u8 tx_count, u8 rx_count)
bp->acquire_resp.resc.current_mac_addr,
ETH_ALEN);
- return 0;
+out:
+ bnx2x_vfpf_finalize(bp, &req->first_tlv);
+ return rc;
}
int bnx2x_vfpf_release(struct bnx2x *bp)
{
struct vfpf_release_tlv *req = &bp->vf2pf_mbox->req.release;
struct pfvf_general_resp_tlv *resp = &bp->vf2pf_mbox->resp.general_resp;
- u32 rc = 0, vf_id;
+ u32 rc, vf_id;
/* clear mailbox and prep first tlv */
bnx2x_vfpf_prep(bp, &req->first_tlv, CHANNEL_TLV_RELEASE, sizeof(*req));
- if (bnx2x_get_vf_id(bp, &vf_id))
- return -EAGAIN;
+ if (bnx2x_get_vf_id(bp, &vf_id)) {
+ rc = -EAGAIN;
+ goto out;
+ }
req->vf_id = vf_id;
@@ -308,7 +326,8 @@ int bnx2x_vfpf_release(struct bnx2x *bp)
if (rc)
/* PF timeout */
- return rc;
+ goto out;
+
if (resp->hdr.status == PFVF_STATUS_SUCCESS) {
/* PF released us */
DP(BNX2X_MSG_SP, "vf released\n");
@@ -316,10 +335,13 @@ int bnx2x_vfpf_release(struct bnx2x *bp)
/* PF reports error */
BNX2X_ERR("PF failed our release request - are we out of sync? response status: %d\n",
resp->hdr.status);
- return -EAGAIN;
+ rc = -EAGAIN;
+ goto out;
}
+out:
+ bnx2x_vfpf_finalize(bp, &req->first_tlv);
- return 0;
+ return rc;
}
/* Tell PF about SB addresses */
@@ -350,16 +372,20 @@ int bnx2x_vfpf_init(struct bnx2x *bp)
rc = bnx2x_send_msg2pf(bp, &resp->hdr.status, bp->vf2pf_mbox_mapping);
if (rc)
- return rc;
+ goto out;
if (resp->hdr.status != PFVF_STATUS_SUCCESS) {
BNX2X_ERR("INIT VF failed: %d. Breaking...\n",
resp->hdr.status);
- return -EAGAIN;
+ rc = -EAGAIN;
+ goto out;
}
DP(BNX2X_MSG_SP, "INIT VF Succeeded\n");
- return 0;
+out:
+ bnx2x_vfpf_finalize(bp, &req->first_tlv);
+
+ return rc;
}
/* CLOSE VF - opposite to INIT_VF */
@@ -401,6 +427,8 @@ void bnx2x_vfpf_close_vf(struct bnx2x *bp)
BNX2X_ERR("Sending CLOSE failed: pf response was %d\n",
resp->hdr.status);
+ bnx2x_vfpf_finalize(bp, &req->first_tlv);
+
free_irq:
/* Disable HW interrupts, NAPI */
bnx2x_netif_stop(bp, 0);
@@ -486,8 +514,11 @@ int bnx2x_vfpf_setup_q(struct bnx2x *bp, int fp_idx)
if (resp->hdr.status != PFVF_STATUS_SUCCESS) {
BNX2X_ERR("Status of SETUP_Q for queue[%d] is %d\n",
fp_idx, resp->hdr.status);
- return -EINVAL;
+ rc = -EINVAL;
}
+
+ bnx2x_vfpf_finalize(bp, &req->first_tlv);
+
return rc;
}
@@ -515,17 +546,19 @@ int bnx2x_vfpf_teardown_queue(struct bnx2x *bp, int qidx)
if (rc) {
BNX2X_ERR("Sending TEARDOWN for queue %d failed: %d\n", qidx,
rc);
- return rc;
+ goto out;
}
/* PF failed the transaction */
if (resp->hdr.status != PFVF_STATUS_SUCCESS) {
BNX2X_ERR("TEARDOWN for queue %d failed: %d\n", qidx,
resp->hdr.status);
- return -EINVAL;
+ rc = -EINVAL;
}
- return 0;
+out:
+ bnx2x_vfpf_finalize(bp, &req->first_tlv);
+ return rc;
}
/* request pf to add a mac for the vf */
@@ -533,7 +566,7 @@ int bnx2x_vfpf_set_mac(struct bnx2x *bp)
{
struct vfpf_set_q_filters_tlv *req = &bp->vf2pf_mbox->req.set_q_filters;
struct pfvf_general_resp_tlv *resp = &bp->vf2pf_mbox->resp.general_resp;
- int rc;
+ int rc = 0;
/* clear mailbox and prep first tlv */
bnx2x_vfpf_prep(bp, &req->first_tlv, CHANNEL_TLV_SET_Q_FILTERS,
@@ -562,7 +595,7 @@ int bnx2x_vfpf_set_mac(struct bnx2x *bp)
rc = bnx2x_send_msg2pf(bp, &resp->hdr.status, bp->vf2pf_mbox_mapping);
if (rc) {
BNX2X_ERR("failed to send message to pf. rc was %d\n", rc);
- return rc;
+ goto out;
}
/* failure may mean PF was configured with a new mac for us */
@@ -587,8 +620,10 @@ int bnx2x_vfpf_set_mac(struct bnx2x *bp)
if (resp->hdr.status != PFVF_STATUS_SUCCESS) {
BNX2X_ERR("vfpf SET MAC failed: %d\n", resp->hdr.status);
- return -EINVAL;
+ rc = -EINVAL;
}
+out:
+ bnx2x_vfpf_finalize(bp, &req->first_tlv);
return 0;
}
@@ -643,14 +678,16 @@ int bnx2x_vfpf_set_mcast(struct net_device *dev)
rc = bnx2x_send_msg2pf(bp, &resp->hdr.status, bp->vf2pf_mbox_mapping);
if (rc) {
BNX2X_ERR("Sending a message failed: %d\n", rc);
- return rc;
+ goto out;
}
if (resp->hdr.status != PFVF_STATUS_SUCCESS) {
BNX2X_ERR("Set Rx mode/multicast failed: %d\n",
resp->hdr.status);
- return -EINVAL;
+ rc = -EINVAL;
}
+out:
+ bnx2x_vfpf_finalize(bp, &req->first_tlv);
return 0;
}
@@ -689,7 +726,8 @@ int bnx2x_vfpf_storm_rx_mode(struct bnx2x *bp)
break;
default:
BNX2X_ERR("BAD rx mode (%d)\n", mode);
- return -EINVAL;
+ rc = -EINVAL;
+ goto out;
}
req->flags |= VFPF_SET_Q_FILTERS_RX_MASK_CHANGED;
@@ -708,8 +746,10 @@ int bnx2x_vfpf_storm_rx_mode(struct bnx2x *bp)
if (resp->hdr.status != PFVF_STATUS_SUCCESS) {
BNX2X_ERR("Set Rx mode failed: %d\n", resp->hdr.status);
- return -EINVAL;
+ rc = -EINVAL;
}
+out:
+ bnx2x_vfpf_finalize(bp, &req->first_tlv);
return rc;
}
--
1.8.1.227.g44fe835
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH net-next 5/6] bnx2x: Support reading I2C EEPROM SFF8472
2013-03-27 11:05 [PATCH net-next 00/06] bnx2x: net-next patch series Yuval Mintz
` (3 preceding siblings ...)
2013-03-27 11:05 ` [PATCH net-next 4/6] bnx2x: Prevent VF race Yuval Mintz
@ 2013-03-27 11:05 ` Yuval Mintz
2013-03-27 11:05 ` [PATCH net-next 6/6] bnx2x: Cosmetic changes Yuval Mintz
2013-03-27 17:09 ` [PATCH net-next 00/06] bnx2x: net-next patch series David Miller
6 siblings, 0 replies; 8+ messages in thread
From: Yuval Mintz @ 2013-03-27 11:05 UTC (permalink / raw)
To: davem, netdev; +Cc: eilong, ariele, Yaniv Rosner, Yuval Mintz
From: Yaniv Rosner <yanivr@broadcom.com>
Add full support for "ethtool -m" command.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
---
.../net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c | 98 +++++++++++++++-----
drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c | 101 +++++++++++++--------
drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h | 16 +++-
3 files changed, 155 insertions(+), 60 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
index 324d691..129d6b2 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
@@ -1393,10 +1393,9 @@ static int bnx2x_get_module_eeprom(struct net_device *dev,
u8 *data)
{
struct bnx2x *bp = netdev_priv(dev);
- int rc = 0, phy_idx;
+ int rc = -EINVAL, phy_idx;
u8 *user_data = data;
- int remaining_len = ee->len, xfer_size;
- unsigned int page_off = ee->offset;
+ unsigned int start_addr = ee->offset, xfer_size = 0;
if (!netif_running(dev)) {
DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM,
@@ -1405,21 +1404,52 @@ static int bnx2x_get_module_eeprom(struct net_device *dev,
}
phy_idx = bnx2x_get_cur_phy_idx(bp);
- bnx2x_acquire_phy_lock(bp);
- while (!rc && remaining_len > 0) {
- xfer_size = (remaining_len > SFP_EEPROM_PAGE_SIZE) ?
- SFP_EEPROM_PAGE_SIZE : remaining_len;
+
+ /* Read A0 section */
+ if (start_addr < ETH_MODULE_SFF_8079_LEN) {
+ /* Limit transfer size to the A0 section boundary */
+ if (start_addr + ee->len > ETH_MODULE_SFF_8079_LEN)
+ xfer_size = ETH_MODULE_SFF_8079_LEN - start_addr;
+ else
+ xfer_size = ee->len;
+ bnx2x_acquire_phy_lock(bp);
rc = bnx2x_read_sfp_module_eeprom(&bp->link_params.phy[phy_idx],
&bp->link_params,
- page_off,
+ I2C_DEV_ADDR_A0,
+ start_addr,
xfer_size,
user_data);
- remaining_len -= xfer_size;
+ bnx2x_release_phy_lock(bp);
+ if (rc) {
+ DP(BNX2X_MSG_ETHTOOL, "Failed reading A0 section\n");
+
+ return -EINVAL;
+ }
user_data += xfer_size;
- page_off += xfer_size;
+ start_addr += xfer_size;
}
- bnx2x_release_phy_lock(bp);
+ /* Read A2 section */
+ if ((start_addr >= ETH_MODULE_SFF_8079_LEN) &&
+ (start_addr < ETH_MODULE_SFF_8472_LEN)) {
+ xfer_size = ee->len - xfer_size;
+ /* Limit transfer size to the A2 section boundary */
+ if (start_addr + xfer_size > ETH_MODULE_SFF_8472_LEN)
+ xfer_size = ETH_MODULE_SFF_8472_LEN - start_addr;
+ start_addr -= ETH_MODULE_SFF_8079_LEN;
+ bnx2x_acquire_phy_lock(bp);
+ rc = bnx2x_read_sfp_module_eeprom(&bp->link_params.phy[phy_idx],
+ &bp->link_params,
+ I2C_DEV_ADDR_A2,
+ start_addr,
+ xfer_size,
+ user_data);
+ bnx2x_release_phy_lock(bp);
+ if (rc) {
+ DP(BNX2X_MSG_ETHTOOL, "Failed reading A2 section\n");
+ return -EINVAL;
+ }
+ }
return rc;
}
@@ -1427,24 +1457,50 @@ static int bnx2x_get_module_info(struct net_device *dev,
struct ethtool_modinfo *modinfo)
{
struct bnx2x *bp = netdev_priv(dev);
- int phy_idx;
+ int phy_idx, rc;
+ u8 sff8472_comp, diag_type;
+
if (!netif_running(dev)) {
- DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM,
+ DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM,
"cannot access eeprom when the interface is down\n");
return -EAGAIN;
}
-
phy_idx = bnx2x_get_cur_phy_idx(bp);
- switch (bp->link_params.phy[phy_idx].media_type) {
- case ETH_PHY_SFPP_10G_FIBER:
- case ETH_PHY_SFP_1G_FIBER:
- case ETH_PHY_DA_TWINAX:
+ bnx2x_acquire_phy_lock(bp);
+ rc = bnx2x_read_sfp_module_eeprom(&bp->link_params.phy[phy_idx],
+ &bp->link_params,
+ I2C_DEV_ADDR_A0,
+ SFP_EEPROM_SFF_8472_COMP_ADDR,
+ SFP_EEPROM_SFF_8472_COMP_SIZE,
+ &sff8472_comp);
+ bnx2x_release_phy_lock(bp);
+ if (rc) {
+ DP(BNX2X_MSG_ETHTOOL, "Failed reading SFF-8472 comp field\n");
+ return -EINVAL;
+ }
+
+ bnx2x_acquire_phy_lock(bp);
+ rc = bnx2x_read_sfp_module_eeprom(&bp->link_params.phy[phy_idx],
+ &bp->link_params,
+ I2C_DEV_ADDR_A0,
+ SFP_EEPROM_DIAG_TYPE_ADDR,
+ SFP_EEPROM_DIAG_TYPE_SIZE,
+ &diag_type);
+ bnx2x_release_phy_lock(bp);
+ if (rc) {
+ DP(BNX2X_MSG_ETHTOOL, "Failed reading Diag Type field\n");
+ return -EINVAL;
+ }
+
+ if (!sff8472_comp ||
+ (diag_type & SFP_EEPROM_DIAG_ADDR_CHANGE_REQ)) {
modinfo->type = ETH_MODULE_SFF_8079;
modinfo->eeprom_len = ETH_MODULE_SFF_8079_LEN;
- return 0;
- default:
- return -EOPNOTSUPP;
+ } else {
+ modinfo->type = ETH_MODULE_SFF_8472;
+ modinfo->eeprom_len = ETH_MODULE_SFF_8472_LEN;
}
+ return 0;
}
static int bnx2x_nvram_write_dword(struct bnx2x *bp, u32 offset, u32 val,
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
index e3fa808..b1b034d 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
@@ -27,6 +27,10 @@
#include "bnx2x.h"
#include "bnx2x_cmn.h"
+typedef int (*read_sfp_module_eeprom_func_p)(struct bnx2x_phy *phy,
+ struct link_params *params,
+ u8 dev_addr, u16 addr, u8 byte_cnt,
+ u8 *o_buf, u8);
/********************************************************/
#define ETH_HLEN 14
/* L2 header size + 2*VLANs (8 bytes) + LLC SNAP (8 bytes) */
@@ -3128,11 +3132,6 @@ static int bnx2x_bsc_read(struct link_params *params,
int rc = 0;
struct bnx2x *bp = params->bp;
- if ((sl_devid != 0xa0) && (sl_devid != 0xa2)) {
- DP(NETIF_MSG_LINK, "invalid sl_devid 0x%x\n", sl_devid);
- return -EINVAL;
- }
-
if (xfer_cnt > 16) {
DP(NETIF_MSG_LINK, "invalid xfer_cnt %d. Max is 16 bytes\n",
xfer_cnt);
@@ -7770,7 +7769,8 @@ static void bnx2x_sfp_set_transmitter(struct link_params *params,
static int bnx2x_8726_read_sfp_module_eeprom(struct bnx2x_phy *phy,
struct link_params *params,
- u16 addr, u8 byte_cnt, u8 *o_buf)
+ u8 dev_addr, u16 addr, u8 byte_cnt,
+ u8 *o_buf, u8 is_init)
{
struct bnx2x *bp = params->bp;
u16 val = 0;
@@ -7783,7 +7783,7 @@ static int bnx2x_8726_read_sfp_module_eeprom(struct bnx2x_phy *phy,
/* Set the read command byte count */
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT,
- (byte_cnt | 0xa000));
+ (byte_cnt | (dev_addr << 8)));
/* Set the read command address */
bnx2x_cl45_write(bp, phy,
@@ -7857,6 +7857,7 @@ static void bnx2x_warpcore_power_module(struct link_params *params,
}
static int bnx2x_warpcore_read_sfp_module_eeprom(struct bnx2x_phy *phy,
struct link_params *params,
+ u8 dev_addr,
u16 addr, u8 byte_cnt,
u8 *o_buf, u8 is_init)
{
@@ -7881,7 +7882,7 @@ static int bnx2x_warpcore_read_sfp_module_eeprom(struct bnx2x_phy *phy,
usleep_range(1000, 2000);
bnx2x_warpcore_power_module(params, 1);
}
- rc = bnx2x_bsc_read(params, phy, 0xa0, addr32, 0, byte_cnt,
+ rc = bnx2x_bsc_read(params, phy, dev_addr, addr32, 0, byte_cnt,
data_array);
} while ((rc != 0) && (++cnt < I2C_WA_RETRY_CNT));
@@ -7897,7 +7898,8 @@ static int bnx2x_warpcore_read_sfp_module_eeprom(struct bnx2x_phy *phy,
static int bnx2x_8727_read_sfp_module_eeprom(struct bnx2x_phy *phy,
struct link_params *params,
- u16 addr, u8 byte_cnt, u8 *o_buf)
+ u8 dev_addr, u16 addr, u8 byte_cnt,
+ u8 *o_buf, u8 is_init)
{
struct bnx2x *bp = params->bp;
u16 val, i;
@@ -7908,6 +7910,15 @@ static int bnx2x_8727_read_sfp_module_eeprom(struct bnx2x_phy *phy,
return -EINVAL;
}
+ /* Set 2-wire transfer rate of SFP+ module EEPROM
+ * to 100Khz since some DACs(direct attached cables) do
+ * not work at 400Khz.
+ */
+ bnx2x_cl45_write(bp, phy,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8727_TWO_WIRE_SLAVE_ADDR,
+ ((dev_addr << 8) | 1));
+
/* Need to read from 1.8000 to clear it */
bnx2x_cl45_read(bp, phy,
MDIO_PMA_DEVAD,
@@ -7980,26 +7991,44 @@ static int bnx2x_8727_read_sfp_module_eeprom(struct bnx2x_phy *phy,
return -EINVAL;
}
-
int bnx2x_read_sfp_module_eeprom(struct bnx2x_phy *phy,
- struct link_params *params, u16 addr,
- u8 byte_cnt, u8 *o_buf)
+ struct link_params *params, u8 dev_addr,
+ u16 addr, u16 byte_cnt, u8 *o_buf)
{
- int rc = -EOPNOTSUPP;
+ int rc = 0;
+ struct bnx2x *bp = params->bp;
+ u8 xfer_size;
+ u8 *user_data = o_buf;
+ read_sfp_module_eeprom_func_p read_func;
+
+ if ((dev_addr != 0xa0) && (dev_addr != 0xa2)) {
+ DP(NETIF_MSG_LINK, "invalid dev_addr 0x%x\n", dev_addr);
+ return -EINVAL;
+ }
+
switch (phy->type) {
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
- rc = bnx2x_8726_read_sfp_module_eeprom(phy, params, addr,
- byte_cnt, o_buf);
- break;
+ read_func = bnx2x_8726_read_sfp_module_eeprom;
+ break;
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722:
- rc = bnx2x_8727_read_sfp_module_eeprom(phy, params, addr,
- byte_cnt, o_buf);
- break;
+ read_func = bnx2x_8727_read_sfp_module_eeprom;
+ break;
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
- rc = bnx2x_warpcore_read_sfp_module_eeprom(phy, params, addr,
- byte_cnt, o_buf, 0);
- break;
+ read_func = bnx2x_warpcore_read_sfp_module_eeprom;
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
+
+ while (!rc && (byte_cnt > 0)) {
+ xfer_size = (byte_cnt > SFP_EEPROM_PAGE_SIZE) ?
+ SFP_EEPROM_PAGE_SIZE : byte_cnt;
+ rc = read_func(phy, params, dev_addr, addr, xfer_size,
+ user_data, 0);
+ byte_cnt -= xfer_size;
+ user_data += xfer_size;
+ addr += xfer_size;
}
return rc;
}
@@ -8016,6 +8045,7 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy,
/* First check for copper cable */
if (bnx2x_read_sfp_module_eeprom(phy,
params,
+ I2C_DEV_ADDR_A0,
SFP_EEPROM_CON_TYPE_ADDR,
2,
(u8 *)val) != 0) {
@@ -8033,6 +8063,7 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy,
*/
if (bnx2x_read_sfp_module_eeprom(phy,
params,
+ I2C_DEV_ADDR_A0,
SFP_EEPROM_FC_TX_TECH_ADDR,
1,
&copper_module_type) != 0) {
@@ -8117,6 +8148,7 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy,
u8 options[SFP_EEPROM_OPTIONS_SIZE];
if (bnx2x_read_sfp_module_eeprom(phy,
params,
+ I2C_DEV_ADDR_A0,
SFP_EEPROM_OPTIONS_ADDR,
SFP_EEPROM_OPTIONS_SIZE,
options) != 0) {
@@ -8183,6 +8215,7 @@ static int bnx2x_verify_sfp_module(struct bnx2x_phy *phy,
/* Format the warning message */
if (bnx2x_read_sfp_module_eeprom(phy,
params,
+ I2C_DEV_ADDR_A0,
SFP_EEPROM_VENDOR_NAME_ADDR,
SFP_EEPROM_VENDOR_NAME_SIZE,
(u8 *)vendor_name))
@@ -8191,6 +8224,7 @@ static int bnx2x_verify_sfp_module(struct bnx2x_phy *phy,
vendor_name[SFP_EEPROM_VENDOR_NAME_SIZE] = '\0';
if (bnx2x_read_sfp_module_eeprom(phy,
params,
+ I2C_DEV_ADDR_A0,
SFP_EEPROM_PART_NO_ADDR,
SFP_EEPROM_PART_NO_SIZE,
(u8 *)vendor_pn))
@@ -8221,12 +8255,13 @@ static int bnx2x_wait_for_sfp_module_initialized(struct bnx2x_phy *phy,
for (timeout = 0; timeout < 60; timeout++) {
if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT)
- rc = bnx2x_warpcore_read_sfp_module_eeprom(phy,
- params, 1,
- 1, &val, 1);
+ rc = bnx2x_warpcore_read_sfp_module_eeprom(
+ phy, params, I2C_DEV_ADDR_A0, 1, 1, &val,
+ 1);
else
- rc = bnx2x_read_sfp_module_eeprom(phy, params, 1, 1,
- &val);
+ rc = bnx2x_read_sfp_module_eeprom(phy, params,
+ I2C_DEV_ADDR_A0,
+ 1, 1, &val);
if (rc == 0) {
DP(NETIF_MSG_LINK,
"SFP+ module initialization took %d ms\n",
@@ -8235,7 +8270,8 @@ static int bnx2x_wait_for_sfp_module_initialized(struct bnx2x_phy *phy,
}
usleep_range(5000, 10000);
}
- rc = bnx2x_read_sfp_module_eeprom(phy, params, 1, 1, &val);
+ rc = bnx2x_read_sfp_module_eeprom(phy, params, I2C_DEV_ADDR_A0,
+ 1, 1, &val);
return rc;
}
@@ -8392,15 +8428,6 @@ static void bnx2x_8727_specific_func(struct bnx2x_phy *phy,
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_PCS_OPT_CTRL,
val);
-
- /* Set 2-wire transfer rate of SFP+ module EEPROM
- * to 100Khz since some DACs(direct attached cables) do
- * not work at 400Khz.
- */
- bnx2x_cl45_write(bp, phy,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_8727_TWO_WIRE_SLAVE_ADDR,
- 0xa001);
break;
default:
DP(NETIF_MSG_LINK, "Function 0x%x not supported by 8727\n",
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h
index 56c2aae..4df4523 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h
@@ -41,6 +41,9 @@
#define SPEED_AUTO_NEG 0
#define SPEED_20000 20000
+#define I2C_DEV_ADDR_A0 0xa0
+#define I2C_DEV_ADDR_A2 0xa2
+
#define SFP_EEPROM_PAGE_SIZE 16
#define SFP_EEPROM_VENDOR_NAME_ADDR 0x14
#define SFP_EEPROM_VENDOR_NAME_SIZE 16
@@ -54,6 +57,15 @@
#define SFP_EEPROM_SERIAL_SIZE 16
#define SFP_EEPROM_DATE_ADDR 0x54 /* ASCII YYMMDD */
#define SFP_EEPROM_DATE_SIZE 6
+#define SFP_EEPROM_DIAG_TYPE_ADDR 0x5c
+#define SFP_EEPROM_DIAG_TYPE_SIZE 1
+#define SFP_EEPROM_DIAG_ADDR_CHANGE_REQ (1<<2)
+#define SFP_EEPROM_SFF_8472_COMP_ADDR 0x5e
+#define SFP_EEPROM_SFF_8472_COMP_SIZE 1
+
+#define SFP_EEPROM_A2_CHECKSUM_RANGE 0x5e
+#define SFP_EEPROM_A2_CC_DMI_ADDR 0x5f
+
#define PWR_FLT_ERR_MSG_LEN 250
#define XGXS_EXT_PHY_TYPE(ext_phy_config) \
@@ -420,8 +432,8 @@ void bnx2x_sfx7101_sp_sw_reset(struct bnx2x *bp, struct bnx2x_phy *phy);
/* Read "byte_cnt" bytes from address "addr" from the SFP+ EEPROM */
int bnx2x_read_sfp_module_eeprom(struct bnx2x_phy *phy,
- struct link_params *params, u16 addr,
- u8 byte_cnt, u8 *o_buf);
+ struct link_params *params, u8 dev_addr,
+ u16 addr, u16 byte_cnt, u8 *o_buf);
void bnx2x_hw_reset_phy(struct link_params *params);
--
1.8.1.227.g44fe835
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH net-next 6/6] bnx2x: Cosmetic changes
2013-03-27 11:05 [PATCH net-next 00/06] bnx2x: net-next patch series Yuval Mintz
` (4 preceding siblings ...)
2013-03-27 11:05 ` [PATCH net-next 5/6] bnx2x: Support reading I2C EEPROM SFF8472 Yuval Mintz
@ 2013-03-27 11:05 ` Yuval Mintz
2013-03-27 17:09 ` [PATCH net-next 00/06] bnx2x: net-next patch series David Miller
6 siblings, 0 replies; 8+ messages in thread
From: Yuval Mintz @ 2013-03-27 11:05 UTC (permalink / raw)
To: davem, netdev; +Cc: eilong, ariele, Yaniv Rosner, Yuval Mintz
From: Yaniv Rosner <yanivr@broadcom.com>
Make few alignments, comment fixes and debug messages.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
---
drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c | 24 +++++++++++++-----------
1 file changed, 13 insertions(+), 11 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
index b1b034d..6cc6c63 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
@@ -3738,7 +3738,7 @@ static void bnx2x_warpcore_enable_AN_KR(struct bnx2x_phy *phy,
if (((vars->line_speed == SPEED_AUTO_NEG) &&
(phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) ||
(vars->line_speed == SPEED_1000)) {
- u32 addr = MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2;
+ u16 addr = MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2;
an_adv |= (1<<5);
/* Enable CL37 1G Parallel Detect */
@@ -4761,8 +4761,8 @@ void bnx2x_link_status_update(struct link_params *params,
port_mb[port].link_status));
/* Force link UP in non LOOPBACK_EXT loopback mode(s) */
- if (bp->link_params.loopback_mode != LOOPBACK_NONE &&
- bp->link_params.loopback_mode != LOOPBACK_EXT)
+ if (params->loopback_mode != LOOPBACK_NONE &&
+ params->loopback_mode != LOOPBACK_EXT)
vars->link_status |= LINK_STATUS_LINK_UP;
if (bnx2x_eee_has_cap(params))
@@ -9571,8 +9571,7 @@ static void bnx2x_save_848xx_spirom_version(struct bnx2x_phy *phy,
} else {
/* For 32-bit registers in 848xx, access via MDIO2ARM i/f. */
/* (1) set reg 0xc200_0014(SPI_BRIDGE_CTRL_2) to 0x03000000 */
- for (i = 0; i < ARRAY_SIZE(reg_set);
- i++)
+ for (i = 0; i < ARRAY_SIZE(reg_set); i++)
bnx2x_cl45_write(bp, phy, reg_set[i].devad,
reg_set[i].reg, reg_set[i].val);
@@ -12286,7 +12285,7 @@ static void bnx2x_init_bmac_loopback(struct link_params *params,
bnx2x_xgxs_deassert(params);
- /* set bmac loopback */
+ /* Set bmac loopback */
bnx2x_bmac_enable(params, vars, 1, 1);
REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0);
@@ -12305,7 +12304,7 @@ static void bnx2x_init_emac_loopback(struct link_params *params,
vars->phy_flags = PHY_XGXS_FLAG;
bnx2x_xgxs_deassert(params);
- /* set bmac loopback */
+ /* Set bmac loopback */
bnx2x_emac_enable(params, vars, 1);
bnx2x_emac_program(params, vars);
REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0);
@@ -12565,6 +12564,7 @@ int bnx2x_phy_init(struct link_params *params, struct link_vars *vars)
params->req_line_speed[0], params->req_flow_ctrl[0]);
DP(NETIF_MSG_LINK, "(2) req_speed %d, req_flowctrl %d\n",
params->req_line_speed[1], params->req_flow_ctrl[1]);
+ DP(NETIF_MSG_LINK, "req_adv_flow_ctrl 0x%x\n", params->req_fc_auto_adv);
vars->link_status = 0;
vars->phy_link_up = 0;
vars->link_up = 0;
@@ -13490,8 +13490,8 @@ static void bnx2x_check_kr2_wa(struct link_params *params,
}
/* Once KR2 was disabled, wait 5 seconds before checking KR2 recovery
- * since some switches tend to reinit the AN process and clear the
- * advertised BP/NP after ~2 seconds causing the KR2 to be disabled
+ * Since some switches tend to reinit the AN process and clear the
+ * the advertised BP/NP after ~2 seconds causing the KR2 to be disabled
* and recovered many times
*/
if (vars->check_kr2_recovery_cnt > 0) {
@@ -13509,8 +13509,10 @@ static void bnx2x_check_kr2_wa(struct link_params *params,
/* CL73 has not begun yet */
if (base_page == 0) {
- if (!(vars->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE))
+ if (!(vars->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) {
bnx2x_kr2_recovery(params, vars, phy);
+ DP(NETIF_MSG_LINK, "No BP\n");
+ }
return;
}
@@ -13526,7 +13528,7 @@ static void bnx2x_check_kr2_wa(struct link_params *params,
if (!(vars->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) {
if (!not_kr2_device) {
DP(NETIF_MSG_LINK, "BP=0x%x, NP=0x%x\n", base_page,
- next_page);
+ next_page);
bnx2x_kr2_recovery(params, vars, phy);
}
return;
--
1.8.1.227.g44fe835
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH net-next 00/06] bnx2x: net-next patch series
2013-03-27 11:05 [PATCH net-next 00/06] bnx2x: net-next patch series Yuval Mintz
` (5 preceding siblings ...)
2013-03-27 11:05 ` [PATCH net-next 6/6] bnx2x: Cosmetic changes Yuval Mintz
@ 2013-03-27 17:09 ` David Miller
6 siblings, 0 replies; 8+ messages in thread
From: David Miller @ 2013-03-27 17:09 UTC (permalink / raw)
To: yuvalmin; +Cc: netdev, eilong, ariele
From: "Yuval Mintz" <yuvalmin@broadcom.com>
Date: Wed, 27 Mar 2013 13:05:13 +0200
> Hi Dave,
>
> This patch series mostly contains patches correcting the
> behaviour of VFs - preventing races, correcting VFs' statistics,
> etc.
>
> It also enhances bnx2x's `ethtool -m' command.
>
> Please consider applying these patches to 'net-next'.
Series applied.
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2013-03-27 17:09 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2013-03-27 11:05 [PATCH net-next 00/06] bnx2x: net-next patch series Yuval Mintz
2013-03-27 11:05 ` [PATCH net-next 1/6] bnx2x: missing ARI should not be lethal Yuval Mintz
2013-03-27 11:05 ` [PATCH net-next 2/6] bnx2x: Fix VF statistics Yuval Mintz
2013-03-27 11:05 ` [PATCH net-next 3/6] bnx2x: Fix VF outer vlan removal Yuval Mintz
2013-03-27 11:05 ` [PATCH net-next 4/6] bnx2x: Prevent VF race Yuval Mintz
2013-03-27 11:05 ` [PATCH net-next 5/6] bnx2x: Support reading I2C EEPROM SFF8472 Yuval Mintz
2013-03-27 11:05 ` [PATCH net-next 6/6] bnx2x: Cosmetic changes Yuval Mintz
2013-03-27 17:09 ` [PATCH net-next 00/06] bnx2x: net-next patch series David Miller
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).