From: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To: Neil Horman <nhorman@tuxdriver.com>
Cc: netdev@vger.kernel.org, Josh Boyer <jwboyer@redhat.com>,
"David S. Miller" <davem@davemloft.net>,
e1000-devel@lists.sourceforge.net
Subject: Re: [PATCH net-next] e100: Add dma mapping error check
Date: Wed, 03 Apr 2013 14:13:15 -0700 [thread overview]
Message-ID: <1365023595.2089.9.camel@jtkirshe-mobl> (raw)
In-Reply-To: <1364923838-14271-1-git-send-email-nhorman@tuxdriver.com>
[-- Attachment #1: Type: text/plain, Size: 4823 bytes --]
On Tue, 2013-04-02 at 13:30 -0400, Neil Horman wrote:
> e100 uses pci_map_single, but fails to check for a dma mapping error
> after its
> use, resulting in a stack trace:
>
> [ 46.656594] ------------[ cut here ]------------
> [ 46.657004] WARNING: at lib/dma-debug.c:933 check_unmap
> +0x47b/0x950()
> [ 46.657004] Hardware name: To Be Filled By O.E.M.
> [ 46.657004] e100 0000:00:0e.0: DMA-API: device driver failed to
> check map
> error[device address=0x000000007a4540fa] [size=90 bytes] [mapped as
> single]
> [ 46.657004] Modules linked in:
> [ 46.657004] w83627hf hwmon_vid snd_via82xx ppdev snd_ac97_codec
> ac97_bus
> snd_seq snd_pcm snd_mpu401 snd_mpu401_uart ns558 snd_rawmidi gameport
> parport_pc
> e100 snd_seq_device parport snd_page_alloc snd_timer snd soundcore
> skge shpchp
> k8temp mii edac_core i2c_viapro edac_mce_amd nfsd auth_rpcgss nfs_acl
> lockd
> sunrpc binfmt_misc uinput ata_generic pata_acpi radeon i2c_algo_bit
> drm_kms_helper ttm firewire_ohci drm firewire_core pata_via sata_via
> i2c_core
> sata_promise crc_itu_t
> [ 46.657004] Pid: 792, comm: ip Not tainted
> 3.8.0-0.rc6.git0.1.fc19.x86_64 #1
> [ 46.657004] Call Trace:
> [ 46.657004] <IRQ> [<ffffffff81065ed0>] warn_slowpath_common
> +0x70/0xa0
> [ 46.657004] [<ffffffff81065f4c>] warn_slowpath_fmt+0x4c/0x50
> [ 46.657004] [<ffffffff81364cfb>] check_unmap+0x47b/0x950
> [ 46.657004] [<ffffffff8136522f>] debug_dma_unmap_page+0x5f/0x70
> [ 46.657004] [<ffffffffa030f0f0>] ? e100_tx_clean+0x30/0x210 [e100]
> [ 46.657004] [<ffffffffa030f1a8>] e100_tx_clean+0xe8/0x210 [e100]
> [ 46.657004] [<ffffffffa030fc6f>] e100_poll+0x56f/0x6c0 [e100]
> [ 46.657004] [<ffffffff8159dce1>] ? net_rx_action+0xa1/0x370
> [ 46.657004] [<ffffffff8159ddb2>] net_rx_action+0x172/0x370
> [ 46.657004] [<ffffffff810703bf>] __do_softirq+0xef/0x3d0
> [ 46.657004] [<ffffffff816e4ebc>] call_softirq+0x1c/0x30
> [ 46.657004] [<ffffffff8101c485>] do_softirq+0x85/0xc0
> [ 46.657004] [<ffffffff81070885>] irq_exit+0xd5/0xe0
> [ 46.657004] [<ffffffff816e5756>] do_IRQ+0x56/0xc0
> [ 46.657004] [<ffffffff816dacb2>] common_interrupt+0x72/0x72
> [ 46.657004] <EOI> [<ffffffff816da1eb>] ?
> _raw_spin_unlock_irqrestore+0x3b/0x70
> [ 46.657004] [<ffffffff816d124d>] __slab_free+0x58/0x38b
> [ 46.657004] [<ffffffff81214424>] ? fsnotify_clear_marks_by_inode
> +0x34/0x120
> [ 46.657004] [<ffffffff811b0417>] ? kmem_cache_free+0x97/0x320
> [ 46.657004] [<ffffffff8157fc14>] ? sock_destroy_inode+0x34/0x40
> [ 46.657004] [<ffffffff8157fc14>] ? sock_destroy_inode+0x34/0x40
> [ 46.657004] [<ffffffff811b0692>] kmem_cache_free+0x312/0x320
> [ 46.657004] [<ffffffff8157fc14>] sock_destroy_inode+0x34/0x40
> [ 46.657004] [<ffffffff811e8c28>] destroy_inode+0x38/0x60
> [ 46.657004] [<ffffffff811e8d5e>] evict+0x10e/0x1a0
> [ 46.657004] [<ffffffff811e9605>] iput+0xf5/0x180
> [ 46.657004] [<ffffffff811e4338>] dput+0x248/0x310
> [ 46.657004] [<ffffffff811ce0e1>] __fput+0x171/0x240
> [ 46.657004] [<ffffffff811ce26e>] ____fput+0xe/0x10
> [ 46.657004] [<ffffffff8108d54c>] task_work_run+0xac/0xe0
> [ 46.657004] [<ffffffff8106c6ed>] do_exit+0x26d/0xc30
> [ 46.657004] [<ffffffff8109eccc>] ? finish_task_switch+0x7c/0x120
> [ 46.657004] [<ffffffff816dad58>] ? retint_swapgs+0x13/0x1b
> [ 46.657004] [<ffffffff8106d139>] do_group_exit+0x49/0xc0
> [ 46.657004] [<ffffffff8106d1c4>] sys_exit_group+0x14/0x20
> [ 46.657004] [<ffffffff816e3b19>] system_call_fastpath+0x16/0x1b
> [ 46.657004] ---[ end trace 4468c44e2156e7d1 ]---
> [ 46.657004] Mapped at:
> [ 46.657004] [<ffffffff813663d1>] debug_dma_map_page+0x91/0x140
> [ 46.657004] [<ffffffffa030e8eb>] e100_xmit_prepare+0x12b/0x1c0
> [e100]
> [ 46.657004] [<ffffffffa030c924>] e100_exec_cb+0x84/0x140 [e100]
> [ 46.657004] [<ffffffffa030e56a>] e100_xmit_frame+0x3a/0x190 [e100]
> [ 46.657004] [<ffffffff8159ee89>] dev_hard_start_xmit+0x259/0x6c0
>
> Easy fix, modify the cb paramter to e100_exec_cb to return an error,
> and do the
> dma_mapping_error check in the obvious place
>
> This was reported previously here:
> http://article.gmane.org/gmane.linux.network/257893
>
> But nobody stepped up and fixed it.
>
> Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
> Reported-by: Michal Jaegermann <michal@harddata.com>
> CC: Josh Boyer <jwboyer@redhat.com>
> CC: "David S. Miller" <davem@davemloft.net>
> CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
> CC: e1000-devel@lists.sourceforge.net
> ---
> drivers/net/ethernet/intel/e100.c | 36
> +++++++++++++++++++++++++-----------
> 1 file changed, 25 insertions(+), 11 deletions(-)
Thanks Neil, I have added it to my queue.
[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 836 bytes --]
prev parent reply other threads:[~2013-04-03 21:13 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-04-02 17:30 [PATCH net-next] e100: Add dma mapping error check Neil Horman
2013-04-03 21:13 ` Jeff Kirsher [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1365023595.2089.9.camel@jtkirshe-mobl \
--to=jeffrey.t.kirsher@intel.com \
--cc=davem@davemloft.net \
--cc=e1000-devel@lists.sourceforge.net \
--cc=jwboyer@redhat.com \
--cc=netdev@vger.kernel.org \
--cc=nhorman@tuxdriver.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).