* [PATCH net v2 1/8] qlcnic: Fix setting MAC address
2013-05-09 19:25 [PATCH net v2 0/8] qlcnic: Bug fixes Shahed Shaikh
@ 2013-05-09 19:25 ` Shahed Shaikh
2013-05-09 19:25 ` [PATCH net v2 2/8] qlcnic: Fix ethtool strings Shahed Shaikh
` (7 subsequent siblings)
8 siblings, 0 replies; 10+ messages in thread
From: Shahed Shaikh @ 2013-05-09 19:25 UTC (permalink / raw)
To: davem; +Cc: netdev, Dept_NX_Linux_NIC_Driver, Manish Chopra
From: Manish Chopra <manish.chopra@qlogic.com>
o Delete previous unicast MAC which is already programmed
in adapter before setting new unicast MAC
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
---
drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c | 21 +++++++++++++++++++++
1 files changed, 21 insertions(+), 0 deletions(-)
diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c
index 264d5a4..04037b5 100644
--- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c
+++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c
@@ -308,6 +308,23 @@ int qlcnic_read_mac_addr(struct qlcnic_adapter *adapter)
return 0;
}
+static void qlcnic_delete_adapter_mac(struct qlcnic_adapter *adapter)
+{
+ struct qlcnic_mac_list_s *cur;
+ struct list_head *head;
+
+ list_for_each(head, &adapter->mac_list) {
+ cur = list_entry(head, struct qlcnic_mac_list_s, list);
+ if (!memcmp(adapter->mac_addr, cur->mac_addr, ETH_ALEN)) {
+ qlcnic_sre_macaddr_change(adapter, cur->mac_addr,
+ 0, QLCNIC_MAC_DEL);
+ list_del(&cur->list);
+ kfree(cur);
+ return;
+ }
+ }
+}
+
static int qlcnic_set_mac(struct net_device *netdev, void *p)
{
struct qlcnic_adapter *adapter = netdev_priv(netdev);
@@ -322,11 +339,15 @@ static int qlcnic_set_mac(struct net_device *netdev, void *p)
if (!is_valid_ether_addr(addr->sa_data))
return -EINVAL;
+ if (!memcmp(adapter->mac_addr, addr->sa_data, ETH_ALEN))
+ return 0;
+
if (test_bit(__QLCNIC_DEV_UP, &adapter->state)) {
netif_device_detach(netdev);
qlcnic_napi_disable(adapter);
}
+ qlcnic_delete_adapter_mac(adapter);
memcpy(adapter->mac_addr, addr->sa_data, netdev->addr_len);
memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
qlcnic_set_multi(adapter->netdev);
--
1.5.6
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH net v2 2/8] qlcnic: Fix ethtool strings
2013-05-09 19:25 [PATCH net v2 0/8] qlcnic: Bug fixes Shahed Shaikh
2013-05-09 19:25 ` [PATCH net v2 1/8] qlcnic: Fix setting MAC address Shahed Shaikh
@ 2013-05-09 19:25 ` Shahed Shaikh
2013-05-09 19:25 ` [PATCH net v2 3/8] qlcnic: Fix missing bracket in module parameter Shahed Shaikh
` (6 subsequent siblings)
8 siblings, 0 replies; 10+ messages in thread
From: Shahed Shaikh @ 2013-05-09 19:25 UTC (permalink / raw)
To: davem; +Cc: netdev, Dept_NX_Linux_NIC_Driver, Shahed Shaikh
From: Shahed Shaikh <shahed.shaikh@qlogic.com>
o Add missing information in ethtool statistics information array.
o Fix the typo in the statistics information string.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
---
.../net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c | 5 +++--
1 files changed, 3 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c
index 08efb46..6005b06 100644
--- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c
+++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c
@@ -131,12 +131,13 @@ static const char qlcnic_83xx_rx_stats_strings[][ETH_GSTRING_LEN] = {
"ctx_lro_pkt_cnt",
"ctx_ip_csum_error",
"ctx_rx_pkts_wo_ctx",
- "ctx_rx_pkts_dropped_wo_sts",
+ "ctx_rx_pkts_drop_wo_sds_on_card",
+ "ctx_rx_pkts_drop_wo_sds_on_host",
"ctx_rx_osized_pkts",
"ctx_rx_pkts_dropped_wo_rds",
"ctx_rx_unexpected_mcast_pkts",
"ctx_invalid_mac_address",
- "ctx_rx_rds_ring_prim_attemoted",
+ "ctx_rx_rds_ring_prim_attempted",
"ctx_rx_rds_ring_prim_success",
"ctx_num_lro_flows_added",
"ctx_num_lro_flows_removed",
--
1.5.6
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH net v2 3/8] qlcnic: Fix missing bracket in module parameter.
2013-05-09 19:25 [PATCH net v2 0/8] qlcnic: Bug fixes Shahed Shaikh
2013-05-09 19:25 ` [PATCH net v2 1/8] qlcnic: Fix setting MAC address Shahed Shaikh
2013-05-09 19:25 ` [PATCH net v2 2/8] qlcnic: Fix ethtool strings Shahed Shaikh
@ 2013-05-09 19:25 ` Shahed Shaikh
2013-05-09 19:25 ` [PATCH net v2 4/8] qlcnic: Fix ethtool supported port status for 83xx Shahed Shaikh
` (5 subsequent siblings)
8 siblings, 0 replies; 10+ messages in thread
From: Shahed Shaikh @ 2013-05-09 19:25 UTC (permalink / raw)
To: davem; +Cc: netdev, Dept_NX_Linux_NIC_Driver, Himanshu Madhani
From: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
---
drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c | 10 +++++-----
1 files changed, 5 insertions(+), 5 deletions(-)
diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c
index 04037b5..d97446a 100644
--- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c
+++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c
@@ -37,24 +37,24 @@ MODULE_PARM_DESC(qlcnic_mac_learn,
"Mac Filter (0=learning is disabled, 1=Driver learning is enabled, 2=FDB learning is enabled)");
int qlcnic_use_msi = 1;
-MODULE_PARM_DESC(use_msi, "MSI interrupt (0=disabled, 1=enabled");
+MODULE_PARM_DESC(use_msi, "MSI interrupt (0=disabled, 1=enabled)");
module_param_named(use_msi, qlcnic_use_msi, int, 0444);
int qlcnic_use_msi_x = 1;
-MODULE_PARM_DESC(use_msi_x, "MSI-X interrupt (0=disabled, 1=enabled");
+MODULE_PARM_DESC(use_msi_x, "MSI-X interrupt (0=disabled, 1=enabled)");
module_param_named(use_msi_x, qlcnic_use_msi_x, int, 0444);
int qlcnic_auto_fw_reset = 1;
-MODULE_PARM_DESC(auto_fw_reset, "Auto firmware reset (0=disabled, 1=enabled");
+MODULE_PARM_DESC(auto_fw_reset, "Auto firmware reset (0=disabled, 1=enabled)");
module_param_named(auto_fw_reset, qlcnic_auto_fw_reset, int, 0644);
int qlcnic_load_fw_file;
-MODULE_PARM_DESC(load_fw_file, "Load firmware from (0=flash, 1=file");
+MODULE_PARM_DESC(load_fw_file, "Load firmware from (0=flash, 1=file)");
module_param_named(load_fw_file, qlcnic_load_fw_file, int, 0444);
int qlcnic_config_npars;
module_param(qlcnic_config_npars, int, 0444);
-MODULE_PARM_DESC(qlcnic_config_npars, "Configure NPARs (0=disabled, 1=enabled");
+MODULE_PARM_DESC(qlcnic_config_npars, "Configure NPARs (0=disabled, 1=enabled)");
static int qlcnic_probe(struct pci_dev *pdev, const struct pci_device_id *ent);
static void qlcnic_remove(struct pci_dev *pdev);
--
1.5.6
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH net v2 4/8] qlcnic: Fix ethtool supported port status for 83xx
2013-05-09 19:25 [PATCH net v2 0/8] qlcnic: Bug fixes Shahed Shaikh
` (2 preceding siblings ...)
2013-05-09 19:25 ` [PATCH net v2 3/8] qlcnic: Fix missing bracket in module parameter Shahed Shaikh
@ 2013-05-09 19:25 ` Shahed Shaikh
2013-05-09 19:25 ` [PATCH net v2 5/8] qlcnic: Fix reset recovery after transmit timeout Shahed Shaikh
` (4 subsequent siblings)
8 siblings, 0 replies; 10+ messages in thread
From: Shahed Shaikh @ 2013-05-09 19:25 UTC (permalink / raw)
To: davem; +Cc: netdev, Dept_NX_Linux_NIC_Driver, Himanshu Madhani
From: Himanshu Madhani <himanshu.madhani@qlogic.com>
o Fix display for interface while using 'ethtool <device>' for 83xx adapter
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
---
drivers/net/ethernet/qlogic/qlcnic/qlcnic.h | 2 +
.../net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c | 68 +++++++++++++++++++-
.../net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.h | 2 +-
.../net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c | 49 +++++++-------
4 files changed, 94 insertions(+), 27 deletions(-)
diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic.h b/drivers/net/ethernet/qlogic/qlcnic/qlcnic.h
index 90c253b..019c5f7 100644
--- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic.h
+++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic.h
@@ -429,6 +429,7 @@ struct qlcnic_hardware_context {
u16 port_type;
u16 board_type;
+ u16 supported_type;
u16 link_speed;
u16 link_duplex;
@@ -1514,6 +1515,7 @@ void qlcnic_create_diag_entries(struct qlcnic_adapter *adapter);
void qlcnic_remove_diag_entries(struct qlcnic_adapter *adapter);
void qlcnic_82xx_add_sysfs(struct qlcnic_adapter *adapter);
void qlcnic_82xx_remove_sysfs(struct qlcnic_adapter *adapter);
+int qlcnic_82xx_get_settings(struct qlcnic_adapter *, struct ethtool_cmd *);
int qlcnicvf_config_bridged_mode(struct qlcnic_adapter *, u32);
int qlcnicvf_config_led(struct qlcnic_adapter *, u32, u32);
diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c
index ea790a9..642fca0 100644
--- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c
+++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c
@@ -2830,6 +2830,23 @@ int qlcnic_83xx_test_link(struct qlcnic_adapter *adapter)
break;
}
config = cmd.rsp.arg[3];
+ if (QLC_83XX_SFP_PRESENT(config)) {
+ switch (ahw->module_type) {
+ case LINKEVENT_MODULE_OPTICAL_UNKNOWN:
+ case LINKEVENT_MODULE_OPTICAL_SRLR:
+ case LINKEVENT_MODULE_OPTICAL_LRM:
+ case LINKEVENT_MODULE_OPTICAL_SFP_1G:
+ ahw->supported_type = PORT_FIBRE;
+ break;
+ case LINKEVENT_MODULE_TWINAX_UNSUPPORTED_CABLE:
+ case LINKEVENT_MODULE_TWINAX_UNSUPPORTED_CABLELEN:
+ case LINKEVENT_MODULE_TWINAX:
+ ahw->supported_type = PORT_TP;
+ break;
+ default:
+ ahw->supported_type = PORT_OTHER;
+ }
+ }
if (config & 1)
err = 1;
}
@@ -2838,7 +2855,8 @@ out:
return config;
}
-int qlcnic_83xx_get_settings(struct qlcnic_adapter *adapter)
+int qlcnic_83xx_get_settings(struct qlcnic_adapter *adapter,
+ struct ethtool_cmd *ecmd)
{
u32 config = 0;
int status = 0;
@@ -2851,6 +2869,54 @@ int qlcnic_83xx_get_settings(struct qlcnic_adapter *adapter)
ahw->module_type = QLC_83XX_SFP_MODULE_TYPE(config);
/* hard code until there is a way to get it from flash */
ahw->board_type = QLCNIC_BRDTYPE_83XX_10G;
+
+ if (netif_running(adapter->netdev) && ahw->has_link_events) {
+ ethtool_cmd_speed_set(ecmd, ahw->link_speed);
+ ecmd->duplex = ahw->link_duplex;
+ ecmd->autoneg = ahw->link_autoneg;
+ } else {
+ ethtool_cmd_speed_set(ecmd, SPEED_UNKNOWN);
+ ecmd->duplex = DUPLEX_UNKNOWN;
+ ecmd->autoneg = AUTONEG_DISABLE;
+ }
+
+ if (ahw->port_type == QLCNIC_XGBE) {
+ ecmd->supported = SUPPORTED_1000baseT_Full;
+ ecmd->advertising = ADVERTISED_1000baseT_Full;
+ } else {
+ ecmd->supported = (SUPPORTED_10baseT_Half |
+ SUPPORTED_10baseT_Full |
+ SUPPORTED_100baseT_Half |
+ SUPPORTED_100baseT_Full |
+ SUPPORTED_1000baseT_Half |
+ SUPPORTED_1000baseT_Full);
+ ecmd->advertising = (ADVERTISED_100baseT_Half |
+ ADVERTISED_100baseT_Full |
+ ADVERTISED_1000baseT_Half |
+ ADVERTISED_1000baseT_Full);
+ }
+
+ switch (ahw->supported_type) {
+ case PORT_FIBRE:
+ ecmd->supported |= SUPPORTED_FIBRE;
+ ecmd->advertising |= ADVERTISED_FIBRE;
+ ecmd->port = PORT_FIBRE;
+ ecmd->transceiver = XCVR_EXTERNAL;
+ break;
+ case PORT_TP:
+ ecmd->supported |= SUPPORTED_TP;
+ ecmd->advertising |= ADVERTISED_TP;
+ ecmd->port = PORT_TP;
+ ecmd->transceiver = XCVR_INTERNAL;
+ break;
+ default:
+ ecmd->supported |= SUPPORTED_FIBRE;
+ ecmd->advertising |= ADVERTISED_FIBRE;
+ ecmd->port = PORT_OTHER;
+ ecmd->transceiver = XCVR_EXTERNAL;
+ break;
+ }
+ ecmd->phy_address = ahw->physical_port;
return status;
}
diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.h b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.h
index 1f1d85e..faf5553 100644
--- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.h
+++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.h
@@ -603,7 +603,7 @@ int qlcnic_83xx_get_vnic_pf_info(struct qlcnic_adapter *, struct qlcnic_info *);
void qlcnic_83xx_get_minidump_template(struct qlcnic_adapter *);
void qlcnic_83xx_get_stats(struct qlcnic_adapter *adapter, u64 *data);
-int qlcnic_83xx_get_settings(struct qlcnic_adapter *);
+int qlcnic_83xx_get_settings(struct qlcnic_adapter *, struct ethtool_cmd *);
int qlcnic_83xx_set_settings(struct qlcnic_adapter *, struct ethtool_cmd *);
void qlcnic_83xx_get_pauseparam(struct qlcnic_adapter *,
struct ethtool_pauseparam *);
diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c
index 6005b06..f67652d 100644
--- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c
+++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c
@@ -252,6 +252,18 @@ static int
qlcnic_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
{
struct qlcnic_adapter *adapter = netdev_priv(dev);
+
+ if (qlcnic_82xx_check(adapter))
+ return qlcnic_82xx_get_settings(adapter, ecmd);
+ else if (qlcnic_83xx_check(adapter))
+ return qlcnic_83xx_get_settings(adapter, ecmd);
+
+ return -EIO;
+}
+
+int qlcnic_82xx_get_settings(struct qlcnic_adapter *adapter,
+ struct ethtool_cmd *ecmd)
+{
struct qlcnic_hardware_context *ahw = adapter->ahw;
u32 speed, reg;
int check_sfp_module = 0;
@@ -277,10 +289,7 @@ qlcnic_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
} else if (adapter->ahw->port_type == QLCNIC_XGBE) {
u32 val = 0;
- if (qlcnic_83xx_check(adapter))
- qlcnic_83xx_get_settings(adapter);
- else
- val = QLCRD32(adapter, QLCNIC_PORT_MODE_ADDR);
+ val = QLCRD32(adapter, QLCNIC_PORT_MODE_ADDR);
if (val == QLCNIC_PORT_MODE_802_3_AP) {
ecmd->supported = SUPPORTED_1000baseT_Full;
@@ -290,16 +299,13 @@ qlcnic_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
ecmd->advertising = ADVERTISED_10000baseT_Full;
}
- if (netif_running(dev) && adapter->ahw->has_link_events) {
- if (qlcnic_82xx_check(adapter)) {
- reg = QLCRD32(adapter,
- P3P_LINK_SPEED_REG(pcifn));
- speed = P3P_LINK_SPEED_VAL(pcifn, reg);
- ahw->link_speed = speed * P3P_LINK_SPEED_MHZ;
- }
- ethtool_cmd_speed_set(ecmd, adapter->ahw->link_speed);
- ecmd->autoneg = adapter->ahw->link_autoneg;
- ecmd->duplex = adapter->ahw->link_duplex;
+ if (netif_running(adapter->netdev) && ahw->has_link_events) {
+ reg = QLCRD32(adapter, P3P_LINK_SPEED_REG(pcifn));
+ speed = P3P_LINK_SPEED_VAL(pcifn, reg);
+ ahw->link_speed = speed * P3P_LINK_SPEED_MHZ;
+ ethtool_cmd_speed_set(ecmd, ahw->link_speed);
+ ecmd->autoneg = ahw->link_autoneg;
+ ecmd->duplex = ahw->link_duplex;
goto skip;
}
@@ -341,8 +347,8 @@ skip:
case QLCNIC_BRDTYPE_P3P_10G_SFP_QT:
ecmd->advertising |= ADVERTISED_TP;
ecmd->supported |= SUPPORTED_TP;
- check_sfp_module = netif_running(dev) &&
- adapter->ahw->has_link_events;
+ check_sfp_module = netif_running(adapter->netdev) &&
+ ahw->has_link_events;
case QLCNIC_BRDTYPE_P3P_10G_XFP:
ecmd->supported |= SUPPORTED_FIBRE;
ecmd->advertising |= ADVERTISED_FIBRE;
@@ -356,8 +362,8 @@ skip:
ecmd->advertising |=
(ADVERTISED_FIBRE | ADVERTISED_TP);
ecmd->port = PORT_FIBRE;
- check_sfp_module = netif_running(dev) &&
- adapter->ahw->has_link_events;
+ check_sfp_module = netif_running(adapter->netdev) &&
+ ahw->has_link_events;
} else {
ecmd->autoneg = AUTONEG_ENABLE;
ecmd->supported |= (SUPPORTED_TP | SUPPORTED_Autoneg);
@@ -366,13 +372,6 @@ skip:
ecmd->port = PORT_TP;
}
break;
- case QLCNIC_BRDTYPE_83XX_10G:
- ecmd->autoneg = AUTONEG_DISABLE;
- ecmd->supported |= (SUPPORTED_FIBRE | SUPPORTED_TP);
- ecmd->advertising |= (ADVERTISED_FIBRE | ADVERTISED_TP);
- ecmd->port = PORT_FIBRE;
- check_sfp_module = netif_running(dev) && ahw->has_link_events;
- break;
default:
dev_err(&adapter->pdev->dev, "Unsupported board model %d\n",
adapter->ahw->board_type);
--
1.5.6
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH net v2 5/8] qlcnic: Fix reset recovery after transmit timeout
2013-05-09 19:25 [PATCH net v2 0/8] qlcnic: Bug fixes Shahed Shaikh
` (3 preceding siblings ...)
2013-05-09 19:25 ` [PATCH net v2 4/8] qlcnic: Fix ethtool supported port status for 83xx Shahed Shaikh
@ 2013-05-09 19:25 ` Shahed Shaikh
2013-05-09 19:25 ` [PATCH net v2 6/8] qlcnic: Fix bug in diagnostics test reset recovery path Shahed Shaikh
` (3 subsequent siblings)
8 siblings, 0 replies; 10+ messages in thread
From: Shahed Shaikh @ 2013-05-09 19:25 UTC (permalink / raw)
To: davem; +Cc: netdev, Dept_NX_Linux_NIC_Driver, Sony Chacko
From: Sony Chacko <sony.chacko@qlogic.com>
o When transmit timeout happens, recovery attempt should start with
adapter soft reset. If soft reset fails to resume traffic, firmware
dump will be collected and driver will perform a hard reset of the
adapter. Reset recovery on 83xx was failing after a hard reset.
This patch fixes that issue.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
---
.../net/ethernet/qlogic/qlcnic/qlcnic_83xx_init.c | 22 +++++++++++--------
drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c | 15 +++++++++----
2 files changed, 23 insertions(+), 14 deletions(-)
diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_init.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_init.c
index ab1d8d9..c67d1eb 100644
--- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_init.c
+++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_init.c
@@ -435,10 +435,6 @@ static void qlcnic_83xx_idc_attach_driver(struct qlcnic_adapter *adapter)
}
done:
netif_device_attach(netdev);
- if (netif_running(netdev)) {
- netif_carrier_on(netdev);
- netif_wake_queue(netdev);
- }
}
static int qlcnic_83xx_idc_enter_failed_state(struct qlcnic_adapter *adapter,
@@ -642,15 +638,21 @@ static int qlcnic_83xx_idc_reattach_driver(struct qlcnic_adapter *adapter)
static void qlcnic_83xx_idc_update_idc_params(struct qlcnic_adapter *adapter)
{
+ struct qlcnic_hardware_context *ahw = adapter->ahw;
+
qlcnic_83xx_idc_update_drv_presence_reg(adapter, 1, 1);
- clear_bit(__QLCNIC_RESETTING, &adapter->state);
set_bit(QLC_83XX_MBX_READY, &adapter->ahw->idc.status);
qlcnic_83xx_idc_update_audit_reg(adapter, 0, 1);
set_bit(QLC_83XX_MODULE_LOADED, &adapter->ahw->idc.status);
- adapter->ahw->idc.quiesce_req = 0;
- adapter->ahw->idc.delay = QLC_83XX_IDC_FW_POLL_DELAY;
- adapter->ahw->idc.err_code = 0;
- adapter->ahw->idc.collect_dump = 0;
+
+ ahw->idc.quiesce_req = 0;
+ ahw->idc.delay = QLC_83XX_IDC_FW_POLL_DELAY;
+ ahw->idc.err_code = 0;
+ ahw->idc.collect_dump = 0;
+ ahw->reset_context = 0;
+ adapter->tx_timeo_cnt = 0;
+
+ clear_bit(__QLCNIC_RESETTING, &adapter->state);
}
/**
@@ -851,6 +853,7 @@ static int qlcnic_83xx_idc_ready_state(struct qlcnic_adapter *adapter)
/* Check for soft reset request */
if (ahw->reset_context &&
!(val & QLC_83XX_IDC_DISABLE_FW_RESET_RECOVERY)) {
+ adapter->ahw->reset_context = 0;
qlcnic_83xx_idc_tx_soft_reset(adapter);
return ret;
}
@@ -914,6 +917,7 @@ static int qlcnic_83xx_idc_need_quiesce_state(struct qlcnic_adapter *adapter)
static int qlcnic_83xx_idc_failed_state(struct qlcnic_adapter *adapter)
{
dev_err(&adapter->pdev->dev, "%s: please restart!!\n", __func__);
+ clear_bit(__QLCNIC_RESETTING, &adapter->state);
adapter->ahw->idc.err_code = -EIO;
return 0;
diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c
index d97446a..8fb836d 100644
--- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c
+++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c
@@ -2502,12 +2502,17 @@ static void qlcnic_tx_timeout(struct net_device *netdev)
if (test_bit(__QLCNIC_RESETTING, &adapter->state))
return;
- dev_err(&netdev->dev, "transmit timeout, resetting.\n");
-
- if (++adapter->tx_timeo_cnt >= QLCNIC_MAX_TX_TIMEOUTS)
- adapter->need_fw_reset = 1;
- else
+ if (++adapter->tx_timeo_cnt >= QLCNIC_MAX_TX_TIMEOUTS) {
+ netdev_info(netdev, "Tx timeout, reset the adapter.\n");
+ if (qlcnic_82xx_check(adapter))
+ adapter->need_fw_reset = 1;
+ else if (qlcnic_83xx_check(adapter))
+ qlcnic_83xx_idc_request_reset(adapter,
+ QLCNIC_FORCE_FW_DUMP_KEY);
+ } else {
+ netdev_info(netdev, "Tx timeout, reset adapter context.\n");
adapter->ahw->reset_context = 1;
+ }
}
static struct net_device_stats *qlcnic_get_stats(struct net_device *netdev)
--
1.5.6
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH net v2 6/8] qlcnic: Fix bug in diagnostics test reset recovery path
2013-05-09 19:25 [PATCH net v2 0/8] qlcnic: Bug fixes Shahed Shaikh
` (4 preceding siblings ...)
2013-05-09 19:25 ` [PATCH net v2 5/8] qlcnic: Fix reset recovery after transmit timeout Shahed Shaikh
@ 2013-05-09 19:25 ` Shahed Shaikh
2013-05-09 19:25 ` [PATCH net v2 7/8] qlcnic: Fix mailbox response handling Shahed Shaikh
` (2 subsequent siblings)
8 siblings, 0 replies; 10+ messages in thread
From: Shahed Shaikh @ 2013-05-09 19:25 UTC (permalink / raw)
To: davem; +Cc: netdev, Dept_NX_Linux_NIC_Driver, Manish Chopra
From: Manish Chopra <manish.chopra@qlogic.com>
o In order to perform reset recovery during diagnostics tests,
current device status information need to be preserved.
This patch makes the required changes in diagnostics routines
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
---
.../net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c | 14 +++++++++++---
1 files changed, 11 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c
index 642fca0..7b5cb61 100644
--- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c
+++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c
@@ -1276,11 +1276,13 @@ out:
return err;
}
-static int qlcnic_83xx_diag_alloc_res(struct net_device *netdev, int test)
+static int qlcnic_83xx_diag_alloc_res(struct net_device *netdev, int test,
+ int num_sds_ring)
{
struct qlcnic_adapter *adapter = netdev_priv(netdev);
struct qlcnic_host_sds_ring *sds_ring;
struct qlcnic_host_rds_ring *rds_ring;
+ u16 adapter_state = adapter->is_up;
u8 ring;
int ret;
@@ -1304,6 +1306,10 @@ static int qlcnic_83xx_diag_alloc_res(struct net_device *netdev, int test)
ret = qlcnic_fw_create_ctx(adapter);
if (ret) {
qlcnic_detach(adapter);
+ if (adapter_state == QLCNIC_ADAPTER_UP_MAGIC) {
+ adapter->max_sds_rings = num_sds_ring;
+ qlcnic_attach(adapter);
+ }
netif_device_attach(netdev);
return ret;
}
@@ -1596,7 +1602,8 @@ int qlcnic_83xx_loopback_test(struct net_device *netdev, u8 mode)
if (test_and_set_bit(__QLCNIC_RESETTING, &adapter->state))
return -EBUSY;
- ret = qlcnic_83xx_diag_alloc_res(netdev, QLCNIC_LOOPBACK_TEST);
+ ret = qlcnic_83xx_diag_alloc_res(netdev, QLCNIC_LOOPBACK_TEST,
+ max_sds_rings);
if (ret)
goto fail_diag_alloc;
@@ -3112,7 +3119,8 @@ int qlcnic_83xx_interrupt_test(struct net_device *netdev)
if (test_and_set_bit(__QLCNIC_RESETTING, &adapter->state))
return -EIO;
- ret = qlcnic_83xx_diag_alloc_res(netdev, QLCNIC_INTERRUPT_TEST);
+ ret = qlcnic_83xx_diag_alloc_res(netdev, QLCNIC_INTERRUPT_TEST,
+ max_sds_rings);
if (ret)
goto fail_diag_irq;
--
1.5.6
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH net v2 7/8] qlcnic: Fix mailbox response handling.
2013-05-09 19:25 [PATCH net v2 0/8] qlcnic: Bug fixes Shahed Shaikh
` (5 preceding siblings ...)
2013-05-09 19:25 ` [PATCH net v2 6/8] qlcnic: Fix bug in diagnostics test reset recovery path Shahed Shaikh
@ 2013-05-09 19:25 ` Shahed Shaikh
2013-05-09 19:25 ` [PATCH net v2 8/8] qlcnic: Fix validation of link event command Shahed Shaikh
2013-05-11 23:01 ` [PATCH net v2 0/8] qlcnic: Bug fixes David Miller
8 siblings, 0 replies; 10+ messages in thread
From: Shahed Shaikh @ 2013-05-09 19:25 UTC (permalink / raw)
To: davem; +Cc: netdev, Dept_NX_Linux_NIC_Driver, Rajesh Borundia
From: Rajesh Borundia <rajesh.borundia@qlogic.com>
o Fix mailbox response poll time to maximum 5 seconds which
includes mailbox response time as well as time required for
processing AEN if any.
o Driver need to read firmware control mailbox register instead
of host control mailbox register.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
---
.../net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c | 13 +++++--------
.../net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.h | 2 +-
drivers/net/ethernet/qlogic/qlcnic/qlcnic_hw.h | 2 +-
.../ethernet/qlogic/qlcnic/qlcnic_sriov_common.c | 8 +++-----
4 files changed, 10 insertions(+), 15 deletions(-)
diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c
index 7b5cb61..b4ff1e3 100644
--- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c
+++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c
@@ -696,15 +696,14 @@ u32 qlcnic_83xx_mac_rcode(struct qlcnic_adapter *adapter)
return 1;
}
-u32 qlcnic_83xx_mbx_poll(struct qlcnic_adapter *adapter)
+u32 qlcnic_83xx_mbx_poll(struct qlcnic_adapter *adapter, u32 *wait_time)
{
u32 data;
- unsigned long wait_time = 0;
struct qlcnic_hardware_context *ahw = adapter->ahw;
/* wait for mailbox completion */
do {
data = QLCRDX(ahw, QLCNIC_FW_MBX_CTRL);
- if (++wait_time > QLCNIC_MBX_TIMEOUT) {
+ if (++(*wait_time) > QLCNIC_MBX_TIMEOUT) {
data = QLCNIC_RCODE_TIMEOUT;
break;
}
@@ -720,8 +719,8 @@ int qlcnic_83xx_mbx_op(struct qlcnic_adapter *adapter,
u16 opcode;
u8 mbx_err_code;
unsigned long flags;
- u32 rsp, mbx_val, fw_data, rsp_num, mbx_cmd;
struct qlcnic_hardware_context *ahw = adapter->ahw;
+ u32 rsp, mbx_val, fw_data, rsp_num, mbx_cmd, wait_time = 0;
opcode = LSW(cmd->req.arg[0]);
if (!test_bit(QLC_83XX_MBX_READY, &adapter->ahw->idc.status)) {
@@ -754,15 +753,13 @@ int qlcnic_83xx_mbx_op(struct qlcnic_adapter *adapter,
/* Signal FW about the impending command */
QLCWRX(ahw, QLCNIC_HOST_MBX_CTRL, QLCNIC_SET_OWNER);
poll:
- rsp = qlcnic_83xx_mbx_poll(adapter);
+ rsp = qlcnic_83xx_mbx_poll(adapter, &wait_time);
if (rsp != QLCNIC_RCODE_TIMEOUT) {
/* Get the FW response data */
fw_data = readl(QLCNIC_MBX_FW(ahw, 0));
if (fw_data & QLCNIC_MBX_ASYNC_EVENT) {
__qlcnic_83xx_process_aen(adapter);
- mbx_val = QLCRDX(ahw, QLCNIC_HOST_MBX_CTRL);
- if (mbx_val)
- goto poll;
+ goto poll;
}
mbx_err_code = QLCNIC_MBX_STATUS(fw_data);
rsp_num = QLCNIC_MBX_NUM_REGS(fw_data);
diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.h b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.h
index faf5553..f5db67f 100644
--- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.h
+++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.h
@@ -620,7 +620,7 @@ int qlcnic_83xx_flash_test(struct qlcnic_adapter *);
int qlcnic_83xx_enable_flash_write(struct qlcnic_adapter *);
int qlcnic_83xx_disable_flash_write(struct qlcnic_adapter *);
u32 qlcnic_83xx_mac_rcode(struct qlcnic_adapter *);
-u32 qlcnic_83xx_mbx_poll(struct qlcnic_adapter *);
+u32 qlcnic_83xx_mbx_poll(struct qlcnic_adapter *, u32 *);
void qlcnic_83xx_enable_mbx_poll(struct qlcnic_adapter *);
void qlcnic_83xx_disable_mbx_poll(struct qlcnic_adapter *);
#endif
diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_hw.h b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_hw.h
index 95b1b57..b6818f4 100644
--- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_hw.h
+++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_hw.h
@@ -134,7 +134,7 @@ struct qlcnic_mailbox_metadata {
#define QLCNIC_SET_OWNER 1
#define QLCNIC_CLR_OWNER 0
-#define QLCNIC_MBX_TIMEOUT 10000
+#define QLCNIC_MBX_TIMEOUT 5000
#define QLCNIC_MBX_RSP_OK 1
#define QLCNIC_MBX_PORT_RSP_OK 0x1a
diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c
index 44d547d..3869c38 100644
--- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c
+++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c
@@ -280,9 +280,9 @@ void qlcnic_sriov_cleanup(struct qlcnic_adapter *adapter)
static int qlcnic_sriov_post_bc_msg(struct qlcnic_adapter *adapter, u32 *hdr,
u32 *pay, u8 pci_func, u8 size)
{
+ u32 rsp, mbx_val, fw_data, rsp_num, mbx_cmd, val, wait_time = 0;
struct qlcnic_hardware_context *ahw = adapter->ahw;
unsigned long flags;
- u32 rsp, mbx_val, fw_data, rsp_num, mbx_cmd, val;
u16 opcode;
u8 mbx_err_code;
int i, j;
@@ -330,15 +330,13 @@ static int qlcnic_sriov_post_bc_msg(struct qlcnic_adapter *adapter, u32 *hdr,
* assume something is wrong.
*/
poll:
- rsp = qlcnic_83xx_mbx_poll(adapter);
+ rsp = qlcnic_83xx_mbx_poll(adapter, &wait_time);
if (rsp != QLCNIC_RCODE_TIMEOUT) {
/* Get the FW response data */
fw_data = readl(QLCNIC_MBX_FW(ahw, 0));
if (fw_data & QLCNIC_MBX_ASYNC_EVENT) {
__qlcnic_83xx_process_aen(adapter);
- mbx_val = QLCRDX(ahw, QLCNIC_HOST_MBX_CTRL);
- if (mbx_val)
- goto poll;
+ goto poll;
}
mbx_err_code = QLCNIC_MBX_STATUS(fw_data);
rsp_num = QLCNIC_MBX_NUM_REGS(fw_data);
--
1.5.6
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH net v2 8/8] qlcnic: Fix validation of link event command.
2013-05-09 19:25 [PATCH net v2 0/8] qlcnic: Bug fixes Shahed Shaikh
` (6 preceding siblings ...)
2013-05-09 19:25 ` [PATCH net v2 7/8] qlcnic: Fix mailbox response handling Shahed Shaikh
@ 2013-05-09 19:25 ` Shahed Shaikh
2013-05-11 23:01 ` [PATCH net v2 0/8] qlcnic: Bug fixes David Miller
8 siblings, 0 replies; 10+ messages in thread
From: Shahed Shaikh @ 2013-05-09 19:25 UTC (permalink / raw)
To: davem; +Cc: netdev, Dept_NX_Linux_NIC_Driver, Rajesh Borundia
From: Rajesh Borundia <rajesh.borundia@qlogic.com>
o VF driver that has enabled asynchronous link events
may not set BIT_8 in the request, if it does not require
link state in the response.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
---
.../net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c | 3 ---
1 files changed, 0 insertions(+), 3 deletions(-)
diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
index c81be2d..1a66ccd 100644
--- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
+++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
@@ -1133,9 +1133,6 @@ static int qlcnic_sriov_validate_linkevent(struct qlcnic_vf_info *vf,
if ((cmd->req.arg[1] >> 16) != vf->rx_ctx_id)
return -EINVAL;
- if (!(cmd->req.arg[1] & BIT_8))
- return -EINVAL;
-
return 0;
}
--
1.5.6
^ permalink raw reply related [flat|nested] 10+ messages in thread* Re: [PATCH net v2 0/8] qlcnic: Bug fixes
2013-05-09 19:25 [PATCH net v2 0/8] qlcnic: Bug fixes Shahed Shaikh
` (7 preceding siblings ...)
2013-05-09 19:25 ` [PATCH net v2 8/8] qlcnic: Fix validation of link event command Shahed Shaikh
@ 2013-05-11 23:01 ` David Miller
8 siblings, 0 replies; 10+ messages in thread
From: David Miller @ 2013-05-11 23:01 UTC (permalink / raw)
To: shahed.shaikh; +Cc: netdev, Dept_NX_Linux_NIC_Driver
From: Shahed Shaikh <shahed.shaikh@qlogic.com>
Date: Thu, 9 May 2013 15:25:08 -0400
> This patch series has following bug fixes:
> * Fix a bug in unicast MAC address setting in adapter.
> Driver was not deleting older unicast MAC while adding new one.
> * Fix an ethtool stats string array by adding missing string entry
> and fix a typo.
> * Fix module paramter description. Bracket ')' was missing.
> * Fix port status provided though 'ethtool <device>' for 83xx adapter.
> * Fix reset recovery path in case of transmit timeout.
> * Fix reset recovery during diagnostic tests by preserving
> current device status information.
> * Fix mailbox response handling. Driver was not maintaining poll time properly.
> * Fix validation of link event command.
Series applied, thanks.
^ permalink raw reply [flat|nested] 10+ messages in thread