[PATCH net-next] cnic, bnx2i: Fix bug on some bnx2x devices that don't support iSCSI

["Michael Chan" <mchan@broadcom.com>]

On some bnx2x devices, iSCSI is determined to be unsupported only after
firmware is downloaded.  We need to check max_iscsi_conn again after
NETDEV_UP and block iSCSI init operations.  Without this fix, iscsiadm
can hang as the firmware will not respond to the iSCSI init message.

Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
---
 drivers/net/ethernet/broadcom/cnic.c |    7 +++++++
 drivers/scsi/bnx2i/bnx2i_init.c      |   12 +++++-------
 2 files changed, 12 insertions(+), 7 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/cnic.c b/drivers/net/ethernet/broadcom/cnic.c
index 6bd6d14..4f8a535 100644
--- a/drivers/net/ethernet/broadcom/cnic.c
+++ b/drivers/net/ethernet/broadcom/cnic.c
@@ -5276,6 +5276,13 @@ static int cnic_register_netdev(struct cnic_dev *dev)
 	if (err)
 		netdev_err(dev->netdev, "register_cnic failed\n");
 
+	/* Read iSCSI config again.  On some bnx2x device, iSCSI config
+	 * can change after firmware is downloaded.
+	 */
+	dev->max_iscsi_conn = ethdev->max_iscsi_conn;
+	if (ethdev->drv_state & CNIC_DRV_STATE_NO_ISCSI)
+		dev->max_iscsi_conn = 0;
+
 	return err;
 }
 
diff --git a/drivers/scsi/bnx2i/bnx2i_init.c b/drivers/scsi/bnx2i/bnx2i_init.c
index 50fef69..3104202 100644
--- a/drivers/scsi/bnx2i/bnx2i_init.c
+++ b/drivers/scsi/bnx2i/bnx2i_init.c
@@ -172,16 +172,14 @@ void bnx2i_start(void *handle)
 	struct bnx2i_hba *hba = handle;
 	int i = HZ;
 
-	/*
-	 * We should never register devices that don't support iSCSI
-	 * (see bnx2i_init_one), so something is wrong if we try to
-	 * start a iSCSI adapter on hardware with 0 supported iSCSI
-	 * connections
+	/* On some bnx2x devices, it is possible that iSCSI is no
+	 * longer supported after firmware is downloaded.  In that
+	 * case, the iscsi_init_msg will return failure.
 	 */
-	BUG_ON(!hba->cnic->max_iscsi_conn);
 
 	bnx2i_send_fw_iscsi_init_msg(hba);
-	while (!test_bit(ADAPTER_STATE_UP, &hba->adapter_state) && i--)
+	while (!test_bit(ADAPTER_STATE_UP, &hba->adapter_state) &&
+	       !test_bit(ADAPTER_STATE_INIT_FAILED, &hba->adapter_state) && i--)
 		msleep(BNX2I_INIT_POLL_TIME);
 }
 
-- 
1.7.1