netdev.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Marc Kleine-Budde <mkl@pengutronix.de>
To: netdev@vger.kernel.org
Cc: davem@davemloft.net, linux-can@vger.kernel.org,
	kernel@pengutronix.de, "Marc Kleine-Budde" <mkl@pengutronix.de>,
	linux-stable <stable@vger.kernel.org>,
	"Lothar Waßmann" <LW@KARO-electronics.de>
Subject: [PATCH 1/3] can: flexcan: flexcan_chip_start: fix regression, mark one MB for TX and abort pending TX
Date: Wed,  9 Oct 2013 23:11:56 +0200	[thread overview]
Message-ID: <1381353118-25111-2-git-send-email-mkl@pengutronix.de> (raw)
In-Reply-To: <1381353118-25111-1-git-send-email-mkl@pengutronix.de>

In patch

    0d1862e can: flexcan: fix flexcan_chip_start() on imx6

the loop in flexcan_chip_start() that iterates over all mailboxes after the
soft reset of the CAN core was removed. This loop put all mailboxes (even the
ones marked as reserved 1...7) into EMPTY/INACTIVE mode. On mailboxes 8...63,
this aborts any pending TX messages.

After a cold boot there is random garbage in the mailboxes, which leads to
spontaneous transmit of CAN frames during first activation. Further if the
interface was disabled with a pending message (usually due to an error
condition on the CAN bus), this message is retransmitted after enabling the
interface again.

This patch fixes the regression by:
1) Limiting the maximum number of used mailboxes to 8, 0...7 are used by the RX
FIFO, 8 is used by TX.
2) Marking the TX mailbox as EMPTY/INACTIVE, so that any pending TX of that
mailbox is aborted.

Cc: linux-stable <stable@vger.kernel.org>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
---
 drivers/net/can/flexcan.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/drivers/net/can/flexcan.c b/drivers/net/can/flexcan.c
index 3f21142..f028c5d 100644
--- a/drivers/net/can/flexcan.c
+++ b/drivers/net/can/flexcan.c
@@ -62,7 +62,7 @@
 #define FLEXCAN_MCR_BCC			BIT(16)
 #define FLEXCAN_MCR_LPRIO_EN		BIT(13)
 #define FLEXCAN_MCR_AEN			BIT(12)
-#define FLEXCAN_MCR_MAXMB(x)		((x) & 0xf)
+#define FLEXCAN_MCR_MAXMB(x)		((x) & 0x1f)
 #define FLEXCAN_MCR_IDAM_A		(0 << 8)
 #define FLEXCAN_MCR_IDAM_B		(1 << 8)
 #define FLEXCAN_MCR_IDAM_C		(2 << 8)
@@ -735,9 +735,11 @@ static int flexcan_chip_start(struct net_device *dev)
 	 *
 	 */
 	reg_mcr = flexcan_read(&regs->mcr);
+	reg_mcr &= ~FLEXCAN_MCR_MAXMB(0xff);
 	reg_mcr |= FLEXCAN_MCR_FRZ | FLEXCAN_MCR_FEN | FLEXCAN_MCR_HALT |
 		FLEXCAN_MCR_SUPV | FLEXCAN_MCR_WRN_EN |
-		FLEXCAN_MCR_IDAM_C | FLEXCAN_MCR_SRX_DIS;
+		FLEXCAN_MCR_IDAM_C | FLEXCAN_MCR_SRX_DIS |
+		FLEXCAN_MCR_MAXMB(FLEXCAN_TX_BUF_ID);
 	netdev_dbg(dev, "%s: writing mcr=0x%08x", __func__, reg_mcr);
 	flexcan_write(reg_mcr, &regs->mcr);
 
@@ -771,6 +773,10 @@ static int flexcan_chip_start(struct net_device *dev)
 	netdev_dbg(dev, "%s: writing ctrl=0x%08x", __func__, reg_ctrl);
 	flexcan_write(reg_ctrl, &regs->ctrl);
 
+	/* Abort any pending TX, mark Mailbox as INACTIVE */
+	flexcan_write(FLEXCAN_MB_CNT_CODE(0x4),
+		      &regs->cantxfg[FLEXCAN_TX_BUF_ID].can_ctrl);
+
 	/* acceptance mask/acceptance code (accept everything) */
 	flexcan_write(0x0, &regs->rxgmask);
 	flexcan_write(0x0, &regs->rx14mask);
-- 
1.8.4.rc3

  reply	other threads:[~2013-10-09 21:12 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2013-10-09 21:11 pull-request: can 2013-10-09 Marc Kleine-Budde
2013-10-09 21:11 ` Marc Kleine-Budde [this message]
2013-10-09 21:11 ` [PATCH 2/3] can: flexcan: fix mx28 detection by rearanging OF match table Marc Kleine-Budde
2013-10-09 21:11 ` [PATCH 3/3] can: at91-can: fix device to driver data mapping for platform devices Marc Kleine-Budde
2013-10-10  3:45 ` pull-request: can 2013-10-09 David Miller

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1381353118-25111-2-git-send-email-mkl@pengutronix.de \
    --to=mkl@pengutronix.de \
    --cc=LW@KARO-electronics.de \
    --cc=davem@davemloft.net \
    --cc=kernel@pengutronix.de \
    --cc=linux-can@vger.kernel.org \
    --cc=netdev@vger.kernel.org \
    --cc=stable@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).