[PATCH net-next 2/6] bnx2x: Add AER support (missing bits)

[Yuval Mintz <yuvalmin@broadcom.com>]

This function adds several OS calls required to fully enable PCIe AER support -
pci_enable_pcie_error_reporting() and pci_cleanup_aer_uncorrect_error_status().

Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
---
 drivers/net/ethernet/broadcom/bnx2x/bnx2x.h      |  1 +
 drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c | 29 ++++++++++++++++++++++++
 2 files changed, 30 insertions(+)

diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
index f09fde6..4bb4f32 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
@@ -1546,6 +1546,7 @@ struct bnx2x {
 #define INTERRUPTS_ENABLED_FLAG		(1 << 23)
 #define BC_SUPPORTS_RMMOD_CMD		(1 << 24)
 #define HAS_PHYS_PORT_ID		(1 << 25)
+#define AER_ENABLED			(1 << 26)
 
 #define BP_NOMCP(bp)			((bp)->flags & NO_MCP_FLAG)
 
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
index 5910413..72973cc 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
@@ -27,6 +27,7 @@
 #include <linux/slab.h>
 #include <linux/interrupt.h>
 #include <linux/pci.h>
+#include <linux/aer.h>
 #include <linux/init.h>
 #include <linux/netdevice.h>
 #include <linux/etherdevice.h>
@@ -12225,6 +12226,14 @@ static int bnx2x_set_coherency_mask(struct bnx2x *bp)
 	return 0;
 }
 
+static void bnx2x_disable_pcie_error_reporting(struct bnx2x *bp)
+{
+	if (bp->flags & AER_ENABLED) {
+		pci_disable_pcie_error_reporting(bp->pdev);
+		bp->flags &= ~AER_ENABLED;
+	}
+}
+
 static int bnx2x_init_dev(struct bnx2x *bp, struct pci_dev *pdev,
 			  struct net_device *dev, unsigned long board_type)
 {
@@ -12331,6 +12340,14 @@ static int bnx2x_init_dev(struct bnx2x *bp, struct pci_dev *pdev,
 	/* clean indirect addresses */
 	pci_write_config_dword(bp->pdev, PCICFG_GRC_ADDRESS,
 			       PCICFG_VENDOR_ID_OFFSET);
+
+	/* AER (Advanced Error reporting) configuration */
+	rc = pci_enable_pcie_error_reporting(pdev);
+	if (!rc)
+		bp->flags |= AER_ENABLED;
+	else
+		BNX2X_DEV_INFO("Failed To configure PCIe AER [%d]\n", rc);
+
 	/*
 	 * Clean the following indirect addresses for all functions since it
 	 * is not used by the driver.
@@ -12938,6 +12955,8 @@ static int bnx2x_init_one(struct pci_dev *pdev,
 	return 0;
 
 init_one_exit:
+	bnx2x_disable_pcie_error_reporting(bp);
+
 	if (bp->regview)
 		iounmap(bp->regview);
 
@@ -13011,6 +13030,8 @@ static void __bnx2x_remove(struct pci_dev *pdev,
 		pci_set_power_state(pdev, PCI_D3hot);
 	}
 
+	bnx2x_disable_pcie_error_reporting(bp);
+
 	if (bp->regview)
 		iounmap(bp->regview);
 
@@ -13188,6 +13209,14 @@ static pci_ers_result_t bnx2x_io_slot_reset(struct pci_dev *pdev)
 
 	rtnl_unlock();
 
+	/* If AER, perform cleanup of the PCIe registers */
+	if (bp->flags & AER_ENABLED) {
+		if (pci_cleanup_aer_uncorrect_error_status(pdev))
+			BNX2X_ERR("pci_cleanup_aer_uncorrect_error_status failed\n");
+		else
+			DP(NETIF_MSG_HW, "pci_cleanup_aer_uncorrect_error_status succeeded\n");
+	}
+
 	return PCI_ERS_RESULT_RECOVERED;
 }
 
-- 
1.8.1.227.g44fe835