From mboxrd@z Thu Jan 1 00:00:00 1970 From: Vince Bridgers Subject: [PATCH net V2 2/2] libphy: Add stubs to hook IEEE MMD Register reads and writes Date: Thu, 29 May 2014 11:28:33 -0500 Message-ID: <1401380913-4207-3-git-send-email-vbridgers2013@gmail.com> References: <1401380913-4207-1-git-send-email-vbridgers2013@gmail.com> Cc: vbridgers2013@gmail.com To: f.fainelli@gmail.com, netdev@vger.kernel.org Return-path: Received: from mail-pb0-f52.google.com ([209.85.160.52]:52498 "EHLO mail-pb0-f52.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1757862AbaE2Qcx (ORCPT ); Thu, 29 May 2014 12:32:53 -0400 Received: by mail-pb0-f52.google.com with SMTP id rr13so649352pbb.11 for ; Thu, 29 May 2014 09:32:52 -0700 (PDT) In-Reply-To: <1401380913-4207-1-git-send-email-vbridgers2013@gmail.com> Sender: netdev-owner@vger.kernel.org List-ID: The Micrel ksz9021 PHY does not support standard IEEE standard MMD extended register access, therefore requires stubs to fail the read register method and do nothing for the write register method when libphy attempts to read and/or configure Energy Efficient Ethernet features in PHYS that do support those features. This problem was observed on an Altera Cyclone V SOC development kit that uses the Synopsys EMAC and the Micrel ksz9021 PHY. This patch was tested on the same board, and Energy Efficient Ethernet is now disabled as expected since the Micrel PHY does not support that feature. Signed-off-by: Vince Bridgers --- V2: Split libphy and Micrel specific changes into 2 patches based on review comments --- drivers/net/phy/micrel.c | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c index d849684..08e9c49 100644 --- a/drivers/net/phy/micrel.c +++ b/drivers/net/phy/micrel.c @@ -316,6 +316,27 @@ static int ksz8873mll_config_aneg(struct phy_device *phydev) return 0; } +/* This routine returns -1 as an indication to the caller that the + * Micrel ksz9021 10/100/1000 PHY does not support standard IEEE + * MMD extended PHY registers. + */ +static int +ksz9021_rd_mmd_phyreg(struct phy_device *phydev, int ptrad, int devnum, + int regnum) +{ + return -1; +} + +/* This routine does nothing since the Micrel ksz9021 does not support + * standard IEEE MMD extended PHY registers. + */ +static void +ksz9021_wr_mmd_phyreg(struct phy_device *phydev, int ptrad, int devnum, + int regnum, u32 val) +{ + return; +} + static struct phy_driver ksphy_driver[] = { { .phy_id = PHY_ID_KS8737, @@ -461,6 +482,8 @@ static struct phy_driver ksphy_driver[] = { .config_intr = ksz9021_config_intr, .suspend = genphy_suspend, .resume = genphy_resume, + .rd_mmd_indirect = ksz9021_rd_mmd_phyreg, + .wr_mmd_indirect = ksz9021_wr_mmd_phyreg, .driver = { .owner = THIS_MODULE, }, }, { .phy_id = PHY_ID_KSZ9031, -- 1.7.9.5