[PATCH] net/phy: micrel: Add clock support for KSZ8021/KSZ8031

[Sascha Hauer <s.hauer@pengutronix.de>]

The KSZ8021 and KSZ8031 support RMII reference input clocks of 25MHz
and 50MHz. Both PHYs differ in the default frequency they expect
after reset. If this differs from the actual input clock, then
register 0x1f bit 7 must be changed.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 Documentation/devicetree/bindings/net/micrel.txt |  6 ++++++
 drivers/net/phy/micrel.c                         | 19 +++++++++++++++++--
 include/linux/micrel_phy.h                       |  1 +
 3 files changed, 24 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/micrel.txt b/Documentation/devicetree/bindings/net/micrel.txt
index 98a3e61..e1d99b9 100644
--- a/Documentation/devicetree/bindings/net/micrel.txt
+++ b/Documentation/devicetree/bindings/net/micrel.txt
@@ -16,3 +16,9 @@ Optional properties:
 	      KSZ8051: register 0x1f, bits 5..4
 
               See the respective PHY datasheet for the mode values.
+
+ - clocks, clock-names: contains clocks according to the common clock bindings.
+
+              supported clocks:
+	      - KSZ8021, KSZ8031: "rmii-ref": The RMII refence input clock. Used
+		to determine the XI input clock.
diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index 011dbda..ca130e9 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -26,6 +26,7 @@
 #include <linux/phy.h>
 #include <linux/micrel_phy.h>
 #include <linux/of.h>
+#include <linux/clk.h>
 
 /* Operation Mode Strap Override */
 #define MII_KSZPHY_OMSO				0x16
@@ -72,9 +73,12 @@ static int ksz_config_flags(struct phy_device *phydev)
 {
 	int regval;
 
-	if (phydev->dev_flags & MICREL_PHY_50MHZ_CLK) {
+	if (phydev->dev_flags & (MICREL_PHY_50MHZ_CLK | MICREL_PHY_25MHZ_CLK)) {
 		regval = phy_read(phydev, MII_KSZPHY_CTRL);
-		regval |= KSZ8051_RMII_50MHZ_CLK;
+		if (phydev->dev_flags & MICREL_PHY_50MHZ_CLK)
+			regval |= KSZ8051_RMII_50MHZ_CLK;
+		else
+			regval &= ~KSZ8051_RMII_50MHZ_CLK;
 		return phy_write(phydev, MII_KSZPHY_CTRL, regval);
 	}
 	return 0;
@@ -187,9 +191,20 @@ static int kszphy_config_init_led8041(struct phy_device *phydev)
 
 static int ksz8021_config_init(struct phy_device *phydev)
 {
+	struct clk *clk;
 	const u16 val = KSZPHY_OMSO_B_CAST_OFF | KSZPHY_OMSO_RMII_OVERRIDE;
 	int rc;
 
+	clk = devm_clk_get(&phydev->dev, "rmii-ref");
+	if (!IS_ERR(clk)) {
+		unsigned long rate = clk_get_rate(clk);
+
+		if (rate > 24500000 && rate < 25500000)
+			phydev->dev_flags |= MICREL_PHY_25MHZ_CLK;
+		else if (rate > 49500000 && rate < 50500000)
+			phydev->dev_flags |= MICREL_PHY_50MHZ_CLK;
+	}
+
 	rc = kszphy_setup_led(phydev, 0x1f, 4);
 	if (rc)
 		dev_err(&phydev->dev, "failed to set led mode\n");
diff --git a/include/linux/micrel_phy.h b/include/linux/micrel_phy.h
index 2e5b194..53d33de 100644
--- a/include/linux/micrel_phy.h
+++ b/include/linux/micrel_phy.h
@@ -37,6 +37,7 @@
 
 /* struct phy_device dev_flags definitions */
 #define MICREL_PHY_50MHZ_CLK	0x00000001
+#define MICREL_PHY_25MHZ_CLK	0x00000002
 
 #define MICREL_KSZ9021_EXTREG_CTRL	0xB
 #define MICREL_KSZ9021_EXTREG_DATA_WRITE	0xC
-- 
2.1.0