Re: [bisected] tg3 broken in 3.18.0?

[Prashant Sreedharan <prashant@broadcom.com>]

On Thu, 2014-12-18 at 21:26 +0100, Nils Holland wrote:
> On Thu, Dec 18, 2014 at 11:28:09AM -0800, Prashant Sreedharan wrote:
> > On Thu, 2014-12-18 at 12:15 -0700, Bjorn Helgaas wrote:
> > > 
> > > Any updates from the hardware team?
> > > 
> > > This is a pretty serious regression, but as far as I can tell, it is
> > > not a PCI bug.  The device should respond to a config read of vendor
> > > ID.  If the driver does something that make the read return CRS
> > > status, I think the driver is responsible for doing whatever delay or
> > > other fixup is required.
> > > 
> > > I'm inclined to reassign this bug to the tg3 driver unless you think
> > > the PCI core is doing something wrong here.
> > > 
> > > Bjorn
> > 
> > We were not able to reproduce this issue, could you please check what is
> > the value of reg 0x70, before the pci_device_is_present call is made ?
> > if bit 15 is set config access will be retried.
> > 
> > --- a/drivers/net/ethernet/broadcom/tg3.c
> > +++ b/drivers/net/ethernet/broadcom/tg3.c
> > @@ -9025,6 +9025,7 @@ static int tg3_chip_reset(struct tg3 *tp)
> >         void (*write_op)(struct tg3 *, u32, u32);
> >         int i, err;
> >  
> > +       printk(KERN_ERR "config state: %x\n", tr32(TG3PCI_PCISTATE));
> >         if (!pci_device_is_present(tp->pdev))
> >                 return -ENODEV;
> 
> No problem, I gave this a try and here is what I get:
> 
> [    2.185190] libphy: tg3 mdio bus: probed
> [    2.229357] tsc: Refined TSC clocksource calibration: 2399.999 MHz
> [    2.244993] config state: 1292
> [    2.247136] tg3 0000:02:00.0 eth0: Tigon3 [partno(BCM57780) rev 57780001]
>         (PCI Express) MAC address 00:19:99:ce:13:a6
> [    2.249279] tg3 0000:02:00.0 eth0: attached PHY driver [Broadcom BCM57780]
>         (mii_bus:phy_addr=200:01)
> [    2.251460] tg3 0000:02:00.0 eth0: RXcsums[1] LinkChgREG[0]
>         MIirq[0] ASF[0] TSOcap[1]
> [    2.253672] tg3 0000:02:00.0 eth0: dma_rwctrl[76180000] dma_mask[64-bit]
> [...]
> [   12.204692] tg3 0000:02:00.0
>         enp2s0: No firmware running
> [   12.206653] config state: 1292
> [   12.208655] config state: 1292
> 
> That's all of the three times the new debugging line gets hit when I
> boot my system using the supplied diagnostic patch.
> 
> Hope that helps - of course, I'd gladly test any further
> (diagnostic) patches if required! Also, if I can provide any
> additional information that might be of value, just ask:-)
> 
Nils/Marcelo thanks for inputs, since reg 0x70 bit 15 is clear it
indicates the chip is not setting the config retry bit. We were hoping
this bit is causing the config access to return CRS but looks like it is
not. 

Btw after forcing the error path (tg3_init_one -> tg3_halt) in the
driver now we are able to reproduce the problem on 5722 in house. We are
working with the HW team to narrow this down.

Also it is not clear to me how reverting commit cfa6a7877b17a667 fixes
the problem.
> Greetings,
> Nils
> --
> To unsubscribe from this list: send the line "unsubscribe netdev" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html