[PATCH v3 0/6] support GMAC driver for RK3288

[PATCH v3 0/6] support GMAC driver for RK3288

[Roger Chen]

Roger Chen (6):
  patch1: add driver for Rockchip RK3288 SoCs integrated GMAC
  patch2: define clock ID used for GMAC
  patch3: modify CRU config for Rockchip RK3288 SoCs integrated GMAC
  patch4: dts: rockchip: add gmac info for rk3288
  patch5: dts: rockchip: enable gmac on RK3288 evb board
  patch6: add document for Rockchip RK3288 GMAC

Tested on rk3288 evb board:
Execute the following command to enable ethernet,
set local IP and ping a remote host.

busybox ifconfig eth0 up
busybox ifconfig eth0 192.168.1.111
ping 192.168.1.1

-- 
1.7.9.5

[PATCH v3 1/6] GMAC: add driver for Rockchip RK3288 SoCs integrated GMAC

[Roger Chen]

This driver is based on stmmac driver.

changes since v2:
- use tab instead of space for macros
- use HIWORD_UPDATE macro for GMAC_CLK_RX_DL_CFG and GMAC_CLK_TX_DL_CFG
- remove drive-strength setting in the driver and set it in the pinctrl settings
- use dev_err instead of pr_err
- remove clock names's macros, just use the real name of the clock
- use devm_clk_get() instead of clk_get()
- remove clk_set_parent(bsp_priv->clk_mac, bsp_priv->clk_mac_pll)
- remove gpio setting for LDO, just use regulator API
- remove phy reset using gpio in the glue layer, it has been handled in the stmmac driver
- remove handling phy interrupt (mii interrupt)

changes since v1:
- use BIT() to set register
- combine two remap_write() operations into one for the same register
- use macros for register value setting
- remove grf fail check in rk_gmac_setup() and save all the check in set_rgmii_speed()
- remove .tx_coe=1 in rk_gmac_data

Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
---
 drivers/net/ethernet/stmicro/stmmac/Makefile       |    2 +-
 drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c     |  459 ++++++++++++++++++++
 .../net/ethernet/stmicro/stmmac/stmmac_platform.c  |    1 +
 .../net/ethernet/stmicro/stmmac/stmmac_platform.h  |    1 +
 4 files changed, 462 insertions(+), 1 deletion(-)
 create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c

diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
index ac4d562..73c2715 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Makefile
+++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
@@ -6,7 +6,7 @@ stmmac-objs:= stmmac_main.o stmmac_ethtool.o stmmac_mdio.o ring_mode.o	\
 
 obj-$(CONFIG_STMMAC_PLATFORM) += stmmac-platform.o
 stmmac-platform-objs:= stmmac_platform.o dwmac-meson.o dwmac-sunxi.o	\
-		       dwmac-sti.o dwmac-socfpga.o
+		       dwmac-sti.o dwmac-socfpga.o dwmac-rk.o
 
 obj-$(CONFIG_STMMAC_PCI) += stmmac-pci.o
 stmmac-pci-objs:= stmmac_pci.o
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
new file mode 100644
index 0000000..35f9b86
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
@@ -0,0 +1,459 @@
+/**
+ * dwmac-rk.c - Rockchip RK3288 DWMAC specific glue layer
+ *
+ * Copyright (C) 2014 Chen-Zhi (Roger Chen)
+ *
+ * Chen-Zhi (Roger Chen)  <roger.chen@rock-chips.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/stmmac.h>
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/phy.h>
+#include <linux/of_net.h>
+#include <linux/gpio.h>
+#include <linux/of_gpio.h>
+#include <linux/of_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/delay.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+
+struct rk_priv_data {
+	struct platform_device *pdev;
+	int phy_iface;
+	char regulator[32];
+
+	bool clk_enabled;
+	bool clock_input;
+
+	struct clk *clk_mac;
+	struct clk *clk_mac_pll;
+	struct clk *gmac_clkin;
+	struct clk *mac_clk_rx;
+	struct clk *mac_clk_tx;
+	struct clk *clk_mac_ref;
+	struct clk *clk_mac_refout;
+	struct clk *aclk_mac;
+	struct clk *pclk_mac;
+
+	int tx_delay;
+	int rx_delay;
+
+	struct regmap *grf;
+};
+
+#define HIWORD_UPDATE(val, mask, shift) \
+		((val) << (shift) | (mask) << ((shift) + 16))
+
+#define GRF_BIT(nr)	(BIT(nr) | BIT(nr+16))
+#define GRF_CLR_BIT(nr)	(BIT(nr+16))
+
+#define RK3288_GRF_SOC_CON1	0x0248
+#define RK3288_GRF_SOC_CON3	0x0250
+#define RK3288_GRF_GPIO3D_E	0x01ec
+#define RK3288_GRF_GPIO4A_E	0x01f0
+#define RK3288_GRF_GPIO4B_E	0x01f4
+
+/*RK3288_GRF_SOC_CON1*/
+#define GMAC_PHY_INTF_SEL_RGMII	(GRF_BIT(6) | GRF_CLR_BIT(7) | GRF_CLR_BIT(8))
+#define GMAC_PHY_INTF_SEL_RMII	(GRF_CLR_BIT(6) | GRF_CLR_BIT(7) | GRF_BIT(8))
+#define GMAC_FLOW_CTRL		GRF_BIT(9)
+#define GMAC_FLOW_CTRL_CLR	GRF_CLR_BIT(9)
+#define GMAC_SPEED_10M		GRF_CLR_BIT(10)
+#define GMAC_SPEED_100M		GRF_BIT(10)
+#define GMAC_RMII_CLK_25M	GRF_BIT(11)
+#define GMAC_RMII_CLK_2_5M	GRF_CLR_BIT(11)
+#define GMAC_CLK_125M		(GRF_CLR_BIT(12) | GRF_CLR_BIT(13))
+#define GMAC_CLK_25M		(GRF_BIT(12) | GRF_BIT(13))
+#define GMAC_CLK_2_5M		(GRF_CLR_BIT(12) | GRF_BIT(13))
+#define GMAC_RMII_MODE		GRF_BIT(14)
+#define GMAC_RMII_MODE_CLR	GRF_CLR_BIT(14)
+
+/*RK3288_GRF_SOC_CON3*/
+#define GMAC_TXCLK_DLY_ENABLE	GRF_BIT(14)
+#define GMAC_TXCLK_DLY_DISABLE	GRF_CLR_BIT(14)
+#define GMAC_RXCLK_DLY_ENABLE	GRF_BIT(15)
+#define GMAC_RXCLK_DLY_DISABLE	GRF_CLR_BIT(15)
+#define GMAC_CLK_RX_DL_CFG(val)	HIWORD_UPDATE(val, 0x7F, 7)
+#define GMAC_CLK_TX_DL_CFG(val)	HIWORD_UPDATE(val, 0x7F, 0)
+
+static void set_to_rgmii(struct rk_priv_data *bsp_priv,
+			 int tx_delay, int rx_delay)
+{
+	struct device *dev = &bsp_priv->pdev->dev;
+
+	if (IS_ERR(bsp_priv->grf)) {
+		dev_err(dev, "%s: Missing rockchip,grf property\n", __func__);
+		return;
+	}
+
+	regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1,
+		     GMAC_PHY_INTF_SEL_RGMII | GMAC_RMII_MODE_CLR);
+	regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON3,
+		     GMAC_RXCLK_DLY_ENABLE | GMAC_TXCLK_DLY_ENABLE |
+		     GMAC_CLK_RX_DL_CFG(rx_delay) |
+		     GMAC_CLK_TX_DL_CFG(tx_delay));
+}
+
+static void set_to_rmii(struct rk_priv_data *bsp_priv)
+{
+	struct device *dev = &bsp_priv->pdev->dev;
+
+	if (IS_ERR(bsp_priv->grf)) {
+		dev_err(dev, "%s: Missing rockchip,grf property\n", __func__);
+		return;
+	}
+
+	regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1,
+		     GMAC_PHY_INTF_SEL_RMII | GMAC_RMII_MODE);
+}
+
+static void set_rgmii_speed(struct rk_priv_data *bsp_priv, int speed)
+{
+	struct device *dev = &bsp_priv->pdev->dev;
+
+	if (IS_ERR(bsp_priv->grf)) {
+		dev_err(dev, "%s: Missing rockchip,grf property\n", __func__);
+		return;
+	}
+
+	if (speed == 10)
+		regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1, GMAC_CLK_2_5M);
+	else if (speed == 100)
+		regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1, GMAC_CLK_25M);
+	else if (speed == 1000)
+		regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1, GMAC_CLK_125M);
+	else
+		dev_err(dev, "unknown speed value for RGMII! speed=%d", speed);
+}
+
+static void set_rmii_speed(struct rk_priv_data *bsp_priv, int speed)
+{
+	struct device *dev = &bsp_priv->pdev->dev;
+
+	if (IS_ERR(bsp_priv->grf)) {
+		dev_err(dev, "%s: Missing rockchip,grf property\n", __func__);
+		return;
+	}
+
+	if (speed == 10) {
+		regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1,
+			     GMAC_RMII_CLK_2_5M | GMAC_SPEED_10M);
+	} else if (speed == 100) {
+		regmap_write(bsp_priv->grf, RK3288_GRF_SOC_CON1,
+			     GMAC_RMII_CLK_25M | GMAC_SPEED_100M);
+	} else {
+		dev_err(dev, "unknown speed value for RMII! speed=%d", speed);
+	}
+}
+
+static int gmac_clk_init(struct rk_priv_data *bsp_priv)
+{
+	struct device *dev = &bsp_priv->pdev->dev;
+
+	bsp_priv->clk_enabled = false;
+
+	bsp_priv->mac_clk_rx = devm_clk_get(dev, "mac_clk_rx");
+	if (IS_ERR(bsp_priv->mac_clk_rx))
+		dev_err(dev, "%s: cannot get clock %s\n",
+			__func__, "mac_clk_rx");
+
+	bsp_priv->mac_clk_tx = devm_clk_get(dev, "mac_clk_tx");
+	if (IS_ERR(bsp_priv->mac_clk_tx))
+		dev_err(dev, "%s: cannot get clock %s\n",
+			__func__, "mac_clk_tx");
+
+	bsp_priv->aclk_mac = devm_clk_get(dev, "aclk_mac");
+	if (IS_ERR(bsp_priv->aclk_mac))
+		dev_err(dev, "%s: cannot get clock %s\n",
+			__func__, "aclk_mac");
+
+	bsp_priv->pclk_mac = devm_clk_get(dev, "pclk_mac");
+	if (IS_ERR(bsp_priv->pclk_mac))
+		dev_err(dev, "%s: cannot get clock %s\n",
+			__func__, "pclk_mac");
+
+	bsp_priv->clk_mac = devm_clk_get(dev, "stmmaceth");
+	if (IS_ERR(bsp_priv->clk_mac))
+		dev_err(dev, "%s: cannot get clock %s\n",
+			__func__, "stmmaceth");
+
+	if (bsp_priv->phy_iface == PHY_INTERFACE_MODE_RMII) {
+		bsp_priv->clk_mac_ref = devm_clk_get(dev, "clk_mac_ref");
+		if (IS_ERR(bsp_priv->clk_mac_ref))
+			dev_err(dev, "%s: cannot get clock %s\n",
+				__func__, "clk_mac_ref");
+
+		if (!bsp_priv->clock_input) {
+			bsp_priv->clk_mac_refout =
+				devm_clk_get(dev, "clk_mac_refout");
+			if (IS_ERR(bsp_priv->clk_mac_refout))
+				dev_err(dev, "%s: cannot get clock %s\n",
+					__func__, "clk_mac_refout");
+		}
+	}
+
+	if (bsp_priv->clock_input) {
+		dev_info(dev, "%s: clock input from PHY\n", __func__);
+	} else {
+		if (bsp_priv->phy_iface == PHY_INTERFACE_MODE_RMII)
+			clk_set_rate(bsp_priv->clk_mac_pll, 50000000);
+	}
+
+	return 0;
+}
+
+static int gmac_clk_enable(struct rk_priv_data *bsp_priv, bool enable)
+{
+	int phy_iface = phy_iface = bsp_priv->phy_iface;
+
+	if (enable) {
+		if (!bsp_priv->clk_enabled) {
+			if (phy_iface == PHY_INTERFACE_MODE_RMII) {
+				if (!IS_ERR(bsp_priv->mac_clk_rx))
+					clk_prepare_enable(
+						bsp_priv->mac_clk_rx);
+
+				if (!IS_ERR(bsp_priv->clk_mac_ref))
+					clk_prepare_enable(
+						bsp_priv->clk_mac_ref);
+
+				if (!IS_ERR(bsp_priv->clk_mac_refout))
+					clk_prepare_enable(
+						bsp_priv->clk_mac_refout);
+			}
+
+			if (!IS_ERR(bsp_priv->aclk_mac))
+				clk_prepare_enable(bsp_priv->aclk_mac);
+
+			if (!IS_ERR(bsp_priv->pclk_mac))
+				clk_prepare_enable(bsp_priv->pclk_mac);
+
+			if (!IS_ERR(bsp_priv->mac_clk_tx))
+				clk_prepare_enable(bsp_priv->mac_clk_tx);
+
+			/**
+			 * if (!IS_ERR(bsp_priv->clk_mac))
+			 *	clk_prepare_enable(bsp_priv->clk_mac);
+			 */
+			mdelay(5);
+			bsp_priv->clk_enabled = true;
+		}
+	} else {
+		if (bsp_priv->clk_enabled) {
+			if (phy_iface == PHY_INTERFACE_MODE_RMII) {
+				if (!IS_ERR(bsp_priv->mac_clk_rx))
+					clk_disable_unprepare(
+						bsp_priv->mac_clk_rx);
+
+				if (!IS_ERR(bsp_priv->clk_mac_ref))
+					clk_disable_unprepare(
+						bsp_priv->clk_mac_ref);
+
+				if (!IS_ERR(bsp_priv->clk_mac_refout))
+					clk_disable_unprepare(
+						bsp_priv->clk_mac_refout);
+			}
+
+			if (!IS_ERR(bsp_priv->aclk_mac))
+				clk_disable_unprepare(bsp_priv->aclk_mac);
+
+			if (!IS_ERR(bsp_priv->pclk_mac))
+				clk_disable_unprepare(bsp_priv->pclk_mac);
+
+			if (!IS_ERR(bsp_priv->mac_clk_tx))
+				clk_disable_unprepare(bsp_priv->mac_clk_tx);
+			/**
+			 * if (!IS_ERR(bsp_priv->clk_mac))
+			 *	clk_disable_unprepare(bsp_priv->clk_mac);
+			 */
+			bsp_priv->clk_enabled = false;
+		}
+	}
+
+	return 0;
+}
+
+static int phy_power_on(struct rk_priv_data *bsp_priv, bool enable)
+{
+	struct regulator *ldo;
+	char *ldostr = bsp_priv->regulator;
+	int ret;
+	struct device *dev = &bsp_priv->pdev->dev;
+
+	if (!ldostr) {
+		dev_err(dev, "%s: no ldo found\n", __func__);
+		return -1;
+	}
+
+	ldo = regulator_get(NULL, ldostr);
+	if (!ldo) {
+		dev_err(dev, "\n%s get ldo %s failed\n", __func__, ldostr);
+	} else {
+		if (enable) {
+			if (!regulator_is_enabled(ldo)) {
+				regulator_set_voltage(ldo, 3300000, 3300000);
+				ret = regulator_enable(ldo);
+				if (ret != 0)
+					dev_err(dev, "%s: fail to enable %s\n",
+						__func__, ldostr);
+				else
+					dev_info(dev, "turn on ldo done.\n");
+			} else {
+				dev_warn(dev, "%s is enabled before enable",
+					 ldostr);
+			}
+		} else {
+			if (regulator_is_enabled(ldo)) {
+				ret = regulator_disable(ldo);
+				if (ret != 0)
+					dev_err(dev, "%s: fail to disable %s\n",
+						__func__, ldostr);
+				else
+					dev_info(dev, "turn off ldo done.\n");
+			} else {
+				dev_warn(dev, "%s is disabled before disable",
+					 ldostr);
+			}
+		}
+		regulator_put(ldo);
+	}
+
+	return 0;
+}
+
+static void *rk_gmac_setup(struct platform_device *pdev)
+{
+	struct rk_priv_data *bsp_priv;
+	struct device *dev = &pdev->dev;
+	int ret;
+	const char *strings = NULL;
+	int value;
+
+	bsp_priv = devm_kzalloc(dev, sizeof(*bsp_priv), GFP_KERNEL);
+	if (!bsp_priv)
+		return ERR_PTR(-ENOMEM);
+
+	bsp_priv->phy_iface = of_get_phy_mode(dev->of_node);
+
+	ret = of_property_read_string(dev->of_node, "phy_regulator", &strings);
+	if (ret) {
+		dev_warn(dev, "%s: Can not read property: phy_regulator.\n",
+			 __func__);
+	} else {
+		dev_info(dev, "%s: PHY power controlled by regulator(%s).\n",
+			 __func__, strings);
+		strcpy(bsp_priv->regulator, strings);
+	}
+
+	ret = of_property_read_string(dev->of_node, "clock_in_out", &strings);
+	if (ret) {
+		dev_err(dev, "%s: Can not read property: clock_in_out.\n",
+			__func__);
+		bsp_priv->clock_input = true;
+	} else {
+		dev_info(dev, "%s: clock input or output? (%s).\n",
+			 __func__, strings);
+		if (!strcmp(strings, "input"))
+			bsp_priv->clock_input = true;
+		else
+			bsp_priv->clock_input = false;
+	}
+
+	ret = of_property_read_u32(dev->of_node, "tx_delay", &value);
+	if (ret) {
+		bsp_priv->tx_delay = 0x30;
+		dev_err(dev, "%s: Can not read property: tx_delay.", __func__);
+		dev_err(dev, "%s: set tx_delay to 0x%x\n",
+			__func__, bsp_priv->tx_delay);
+	} else {
+		dev_info(dev, "%s: TX delay(0x%x).\n", __func__, value);
+		bsp_priv->tx_delay = value;
+	}
+
+	ret = of_property_read_u32(dev->of_node, "rx_delay", &value);
+	if (ret) {
+		bsp_priv->rx_delay = 0x10;
+		dev_err(dev, "%s: Can not read property: rx_delay.", __func__);
+		dev_err(dev, "%s: set rx_delay to 0x%x\n",
+			__func__, bsp_priv->rx_delay);
+	} else {
+		dev_info(dev, "%s: RX delay(0x%x).\n", __func__, value);
+		bsp_priv->rx_delay = value;
+	}
+
+	bsp_priv->grf = syscon_regmap_lookup_by_phandle(dev->of_node,
+							"rockchip,grf");
+	bsp_priv->pdev = pdev;
+
+	/*rmii or rgmii*/
+	if (bsp_priv->phy_iface == PHY_INTERFACE_MODE_RGMII) {
+		dev_info(dev, "%s: init for RGMII\n", __func__);
+		set_to_rgmii(bsp_priv, bsp_priv->tx_delay, bsp_priv->rx_delay);
+	} else if (bsp_priv->phy_iface == PHY_INTERFACE_MODE_RMII) {
+		dev_info(dev, "%s: init for RMII\n", __func__);
+		set_to_rmii(bsp_priv);
+	} else {
+		dev_err(dev, "%s: NO interface defined!\n", __func__);
+	}
+
+	gmac_clk_init(bsp_priv);
+
+	return bsp_priv;
+}
+
+static int rk_gmac_init(struct platform_device *pdev, void *priv)
+{
+	struct rk_priv_data *bsp_priv = priv;
+	int ret;
+
+	ret = phy_power_on(bsp_priv, true);
+	if (ret)
+		return ret;
+
+	ret = gmac_clk_enable(bsp_priv, true);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static void rk_gmac_exit(struct platform_device *pdev, void *priv)
+{
+	struct rk_priv_data *gmac = priv;
+
+	phy_power_on(gmac, false);
+	gmac_clk_enable(gmac, false);
+}
+
+static void rk_fix_speed(void *priv, unsigned int speed)
+{
+	struct rk_priv_data *bsp_priv = priv;
+	struct device *dev = &bsp_priv->pdev->dev;
+
+	if (bsp_priv->phy_iface == PHY_INTERFACE_MODE_RGMII)
+		set_rgmii_speed(bsp_priv, speed);
+	else if (bsp_priv->phy_iface == PHY_INTERFACE_MODE_RMII)
+		set_rmii_speed(bsp_priv, speed);
+	else
+		dev_err(dev, "unsupported interface %d", bsp_priv->phy_iface);
+}
+
+const struct stmmac_of_data rk3288_gmac_data = {
+	.has_gmac = 1,
+	.fix_mac_speed = rk_fix_speed,
+	.setup = rk_gmac_setup,
+	.init = rk_gmac_init,
+	.exit = rk_gmac_exit,
+};
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
index 15814b7..6794993 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
@@ -33,6 +33,7 @@
 
 static const struct of_device_id stmmac_dt_ids[] = {
 	/* SoC specific glue layers should come before generic bindings */
+	{ .compatible = "rockchip,rk3288-gmac", .data = &rk3288_gmac_data},
 	{ .compatible = "amlogic,meson6-dwmac", .data = &meson6_dwmac_data},
 	{ .compatible = "allwinner,sun7i-a20-gmac", .data = &sun7i_gmac_data},
 	{ .compatible = "st,stih415-dwmac", .data = &stih4xx_dwmac_data},
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h
index 25dd1f7..093eb99 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.h
@@ -24,5 +24,6 @@ extern const struct stmmac_of_data sun7i_gmac_data;
 extern const struct stmmac_of_data stih4xx_dwmac_data;
 extern const struct stmmac_of_data stid127_dwmac_data;
 extern const struct stmmac_of_data socfpga_gmac_data;
+extern const struct stmmac_of_data rk3288_gmac_data;
 
 #endif /* __STMMAC_PLATFORM_H__ */
-- 
1.7.9.5

[PATCH v3 2/6] GMAC: define clock ID used for GMAC

[Roger Chen]

changes since v2:
1. remove SCLK_MAC_PLL

Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
---
 include/dt-bindings/clock/rk3288-cru.h |    3 +++
 1 file changed, 3 insertions(+)

diff --git a/include/dt-bindings/clock/rk3288-cru.h b/include/dt-bindings/clock/rk3288-cru.h
index 100a08c..81eb35b 100644
--- a/include/dt-bindings/clock/rk3288-cru.h
+++ b/include/dt-bindings/clock/rk3288-cru.h
@@ -72,6 +72,9 @@
 #define SCLK_HEVC_CABAC		111
 #define SCLK_HEVC_CORE		112
 
+#define SCLK_MAC		151
+#define SCLK_MACREF_OUT		152
+
 #define DCLK_VOP0		190
 #define DCLK_VOP1		191
 
-- 
1.7.9.5

[PATCH v3 3/6] GMAC: modify CRU config for Rockchip RK3288 SoCs integrated GMAC

[Roger Chen]

modify CRU config for GMAC driver

changes since v2:
1. remove SCLK_MAC_PLL

Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
---
 drivers/clk/rockchip/clk-rk3288.c |   14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

diff --git a/drivers/clk/rockchip/clk-rk3288.c b/drivers/clk/rockchip/clk-rk3288.c
index 2327829..6e88a29 100644
--- a/drivers/clk/rockchip/clk-rk3288.c
+++ b/drivers/clk/rockchip/clk-rk3288.c
@@ -187,7 +187,7 @@ PNAME(mux_uart2_p)	= { "uart2_src", "uart2_frac", "xin24m" };
 PNAME(mux_uart3_p)	= { "uart3_src", "uart3_frac", "xin24m" };
 PNAME(mux_uart4_p)	= { "uart4_src", "uart4_frac", "xin24m" };
 PNAME(mux_cif_out_p)	= { "cif_src", "xin24m" };
-PNAME(mux_macref_p)	= { "mac_src", "ext_gmac" };
+PNAME(mux_mac_p)	= { "mac_pll_src", "ext_gmac" };
 PNAME(mux_hsadcout_p)	= { "hsadc_src", "ext_hsadc" };
 PNAME(mux_edp_24m_p)	= { "ext_edp_24m", "xin24m" };
 PNAME(mux_tspout_p)	= { "cpll", "gpll", "npll", "xin27m" };
@@ -560,18 +560,18 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
 	MUX(SCLK_UART4, "sclk_uart4", mux_uart4_p, 0,
 			RK3288_CLKSEL_CON(3), 8, 2, MFLAGS),
 
-	COMPOSITE(0, "mac_src", mux_pll_src_npll_cpll_gpll_p, 0,
+	COMPOSITE(0, "mac_pll_src", mux_pll_src_npll_cpll_gpll_p, 0,
 			RK3288_CLKSEL_CON(21), 0, 2, MFLAGS, 8, 5, DFLAGS,
 			RK3288_CLKGATE_CON(2), 5, GFLAGS),
-	MUX(0, "macref", mux_macref_p, 0,
+	MUX(SCLK_MAC, "mac_clk", mux_mac_p, 0,
 			RK3288_CLKSEL_CON(21), 4, 1, MFLAGS),
-	GATE(0, "sclk_macref_out", "macref", 0,
+	GATE(SCLK_MACREF_OUT, "sclk_macref_out", "mac_clk", 0,
 			RK3288_CLKGATE_CON(5), 3, GFLAGS),
-	GATE(SCLK_MACREF, "sclk_macref", "macref", 0,
+	GATE(SCLK_MACREF, "sclk_macref", "mac_clk", 0,
 			RK3288_CLKGATE_CON(5), 2, GFLAGS),
-	GATE(SCLK_MAC_RX, "sclk_mac_rx", "macref", 0,
+	GATE(SCLK_MAC_RX, "sclk_mac_rx", "mac_clk", 0,
 			RK3288_CLKGATE_CON(5), 0, GFLAGS),
-	GATE(SCLK_MAC_TX, "sclk_mac_tx", "macref", 0,
+	GATE(SCLK_MAC_TX, "sclk_mac_tx", "mac_clk", 0,
 			RK3288_CLKGATE_CON(5), 1, GFLAGS),
 
 	COMPOSITE(0, "hsadc_src", mux_pll_src_cpll_gpll_p, 0,
-- 
1.7.9.5

[PATCH v3 4/6] ARM: dts: rockchip: add gmac info for rk3288

[Roger Chen]

add gmac info in rk3288.dtsi for GMAC driver

changes since v2:
1. add drive-strength in the pinctrl settings

Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
---
 arch/arm/boot/dts/rk3288.dtsi |   54 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 54 insertions(+)

diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi
index 0f50d5d..5a26db0 100644
--- a/arch/arm/boot/dts/rk3288.dtsi
+++ b/arch/arm/boot/dts/rk3288.dtsi
@@ -358,6 +358,22 @@
 		status = "disabled";
 	};
 
+	gmac: ethernet@ff290000 {
+		compatible = "rockchip,rk3288-gmac";
+		reg = <0xff290000 0x10000>;
+		interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "macirq";
+		rockchip,grf = <&grf>;
+		clocks = <&cru SCLK_MAC>,
+			<&cru SCLK_MAC_RX>, <&cru SCLK_MAC_TX>,
+			<&cru SCLK_MACREF>, <&cru SCLK_MACREF_OUT>,
+			<&cru ACLK_GMAC>, <&cru PCLK_GMAC>;
+		clock-names = "stmmaceth",
+			"mac_clk_rx", "mac_clk_tx",
+			"clk_mac_ref", "clk_mac_refout",
+			"aclk_mac", "pclk_mac";
+	};
+
 	usb_host0_ehci: usb@ff500000 {
 		compatible = "generic-ehci";
 		reg = <0xff500000 0x100>;
@@ -703,6 +719,11 @@
 			bias-disable;
 		};
 
+		pcfg_pull_none_12ma: pcfg-pull-none-12ma {
+			bias-disable;
+			drive-strength = <12>;
+		};
+
 		i2c0 {
 			i2c0_xfer: i2c0-xfer {
 				rockchip,pins = <0 15 RK_FUNC_1 &pcfg_pull_none>,
@@ -1040,5 +1061,38 @@
 				rockchip,pins = <7 23 3 &pcfg_pull_none>;
 			};
 		};
+
+		gmac {
+			rgmii_pins: rgmii-pins {
+				rockchip,pins = <3 30 3 &pcfg_pull_none>,
+						<3 31 3 &pcfg_pull_none>,
+						<3 26 3 &pcfg_pull_none>,
+						<3 27 3 &pcfg_pull_none>,
+						<3 28 3 &pcfg_pull_none_12ma>,
+						<3 29 3 &pcfg_pull_none_12ma>,
+						<3 24 3 &pcfg_pull_none_12ma>,
+						<3 25 3 &pcfg_pull_none_12ma>,
+						<4 0 3 &pcfg_pull_none>,
+						<4 5 3 &pcfg_pull_none>,
+						<4 6 3 &pcfg_pull_none>,
+						<4 9 3 &pcfg_pull_none_12ma>,
+						<4 4 3 &pcfg_pull_none_12ma>,
+						<4 1 3 &pcfg_pull_none>,
+						<4 3 3 &pcfg_pull_none>;
+			};
+
+			rmii_pins: rmii-pins {
+				rockchip,pins = <3 30 3 &pcfg_pull_none>,
+						<3 31 3 &pcfg_pull_none>,
+						<3 28 3 &pcfg_pull_none>,
+						<3 29 3 &pcfg_pull_none>,
+						<4 0 3 &pcfg_pull_none>,
+						<4 5 3 &pcfg_pull_none>,
+						<4 4 3 &pcfg_pull_none>,
+						<4 1 3 &pcfg_pull_none>,
+						<4 2 3 &pcfg_pull_none>,
+						<4 3 3 &pcfg_pull_none>;
+			};
+		};
 	};
 };
-- 
1.7.9.5

[PATCH v3 5/6] ARM: dts: rockchip: enable gmac on RK3288 evb board

[Roger Chen]

enable gmac in rk3288-evb-rk808.dts

changes since v2:
1. add fixed regulator for PHY
2. remove power-gpio, reset-gpio, phyirq-gpio, pmu_regulator setting
3. add "snps,reset-gpio", "snps,reset-active-low;" "snps,reset-delays-us"

Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
---
 arch/arm/boot/dts/rk3288-evb-rk808.dts |   23 +++++++++++++++++++++++
 arch/arm/boot/dts/rk3288-evb.dtsi      |   17 +++++++++++++++++
 2 files changed, 40 insertions(+)

diff --git a/arch/arm/boot/dts/rk3288-evb-rk808.dts b/arch/arm/boot/dts/rk3288-evb-rk808.dts
index d8c775e6..831a7aa 100644
--- a/arch/arm/boot/dts/rk3288-evb-rk808.dts
+++ b/arch/arm/boot/dts/rk3288-evb-rk808.dts
@@ -15,6 +15,13 @@
 
 / {
 	compatible = "rockchip,rk3288-evb-rk808", "rockchip,rk3288";
+
+	ext_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+		#clock-cells = <0>;
+	};
 };
 
 &cpu0 {
@@ -152,3 +159,19 @@
 		};
 	};
 };
+
+&gmac {
+	phy_regulator = "vcc_phy";
+	phy-mode = "rgmii";
+	clock_in_out = "input";
+	snps,reset-gpio = <&gpio4 7 0>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	status = "ok";
+};
diff --git a/arch/arm/boot/dts/rk3288-evb.dtsi b/arch/arm/boot/dts/rk3288-evb.dtsi
index cb83cea..fe1d13c 100644
--- a/arch/arm/boot/dts/rk3288-evb.dtsi
+++ b/arch/arm/boot/dts/rk3288-evb.dtsi
@@ -90,6 +90,17 @@
 		regulator-always-on;
 		regulator-boot-on;
 	};
+
+	vcc_phy: vcc-phy-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&eth_phy_pwr>;
+		regulator-name = "vcc_phy";
+		regulator-always-on;
+		regulator-boot-on;
+	};
 };
 
 &emmc {
@@ -172,6 +183,12 @@
 			rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
+
+	eth_phy {
+		eth_phy_pwr: eth-phy-pwr {
+			rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
 };
 
 &usb_host0_ehci {
-- 
1.7.9.5

[PATCH v3 6/6] GMAC: add document for Rockchip RK3288 GMAC

[Roger Chen]

The document descripts how to add properties for GMAC in device tree.

change since v2:

1. remove power-gpio, reset-gpio, phyirq-gpio, pmu_regulator setting
2. add "snps,reset-gpio", "snps,reset-active-low;" "snps,reset-delays-us"

Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
---
 .../devicetree/bindings/net/rockchip-dwmac.txt     |   67 ++++++++++++++++++++
 1 file changed, 67 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/rockchip-dwmac.txt

diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
new file mode 100644
index 0000000..94d887f
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
@@ -0,0 +1,67 @@
+Rockchip SoC RK3288 10/100/1000 Ethernet driver(GMAC)
+
+The device node has following properties.
+
+Required properties:
+ - compatible: Can be "rockchip,rk3288-gmac".
+ - reg: addresses and length of the register sets for the device.
+ - interrupts: Should contain the GMAC interrupts.
+ - interrupt-names: Should contain the interrupt names "macirq".
+ - rockchip,grf: phandle to the syscon grf used to control speed and mode.
+ - clocks: <&cru SCLK_MAC>: clock selector for main clock, from PLL or PHY.
+	   <&cru SCLK_MAC_PLL>: PLL clock for SCLK_MAC
+	   <&cru SCLK_MAC_RX>: clock gate for RX
+	   <&cru SCLK_MAC_TX>: clock gate for TX
+	   <&cru SCLK_MACREF>: clock gate for RMII referce clock
+	   <&cru SCLK_MACREF_OUT> clock gate for RMII reference clock output
+	   <&cru ACLK_GMAC>: AXI clock gate for GMAC 
+	   <&cru PCLK_GMAC>: APB clock gate for GMAC 
+ - clock-names: One name for each entry in the clocks property.
+ - phy-mode: See ethernet.txt file in the same directory.
+ - pinctrl-names: Names corresponding to the numbered pinctrl states.
+ - pinctrl-0: pin-control mode. can be <&rgmii_pins> or <&rmii_pins>.
+ - clock_in_out: For RGMII, it must be "input", means main clock(125MHz)
+   is not sourced from SoC's PLL, but input from PHY; For RMII, "input" means
+   PHY provides the reference clock(50MHz), "output" means GMAC provides the
+   reference clock. 
+ - snps,reset-gpio       gpio number for phy reset.
+ - snps,reset-active-low boolean flag to indicate if phy reset is active low.
+ - assigned-clocks: main clock, should be <&cru SCLK_MAC>;
+ - assigned-clock-parents = parent of main clock.
+   can be <&ext_gmac> or <&cru SCLK_MAC_PLL>.
+
+Optional properties:
+ - tx_delay: Delay value for TXD timing. Range value is 0~0x7F, 0x30 as default.
+ - rx_delay: Delay value for RXD timing. Range value is 0~0x7F, 0x10 as default.
+
+Example:
+
+gmac: ethernet@ff290000 {
+	compatible = "rockchip,rk3288-gmac";
+	reg = <0xff290000 0x10000>;
+	interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+	interrupt-names = "macirq";
+	rockchip,grf = <&grf>;
+	clocks = <&cru SCLK_MAC>,
+		<&cru SCLK_MAC_RX>, <&cru SCLK_MAC_TX>,
+		<&cru SCLK_MACREF>, <&cru SCLK_MACREF_OUT>,
+		<&cru ACLK_GMAC>, <&cru PCLK_GMAC>;
+	clock-names = "stmmaceth",
+		"mac_clk_rx", "mac_clk_tx",
+		"clk_mac_ref", "clk_mac_refout",
+		"aclk_mac", "pclk_mac";
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins /*&rmii_pins*/>;
+
+	clock_in_out = "input";
+	snps,reset-gpio = <&gpio4 7 0>;
+	snps,reset-active-low;
+
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+
+	status = "ok";
+};
-- 
1.7.9.5

Re: [PATCH v3 0/6] support GMAC driver for RK3288

[David Miller]

From: Roger Chen <roger.chen@rock-chips.com>
Date: Mon, 29 Dec 2014 17:42:32 +0800

> Roger Chen (6):
>   patch1: add driver for Rockchip RK3288 SoCs integrated GMAC
>   patch2: define clock ID used for GMAC
>   patch3: modify CRU config for Rockchip RK3288 SoCs integrated GMAC
>   patch4: dts: rockchip: add gmac info for rk3288
>   patch5: dts: rockchip: enable gmac on RK3288 evb board
>   patch6: add document for Rockchip RK3288 GMAC
> 
> Tested on rk3288 evb board:
> Execute the following command to enable ethernet,
> set local IP and ping a remote host.
> 
> busybox ifconfig eth0 up
> busybox ifconfig eth0 192.168.1.111
> ping 192.168.1.1

Series applied to net-next, thanks.

Re: [PATCH v3 0/6] support GMAC driver for RK3288

[Heiko Stübner]

Hi David,

Am Mittwoch, 31. Dezember 2014, 19:15:38 schrieb David Miller:
> From: Roger Chen <roger.chen@rock-chips.com>
> Date: Mon, 29 Dec 2014 17:42:32 +0800
> 
> > Roger Chen (6):
> >   patch1: add driver for Rockchip RK3288 SoCs integrated GMAC
> >   patch2: define clock ID used for GMAC
> >   patch3: modify CRU config for Rockchip RK3288 SoCs integrated GMAC
> >   patch4: dts: rockchip: add gmac info for rk3288
> >   patch5: dts: rockchip: enable gmac on RK3288 evb board
> >   patch6: add document for Rockchip RK3288 GMAC
> > 
> > Tested on rk3288 evb board:
> > Execute the following command to enable ethernet,
> > set local IP and ping a remote host.
> > 
> > busybox ifconfig eth0 up
> > busybox ifconfig eth0 192.168.1.111
> > ping 192.168.1.1
> 
> Series applied to net-next, thanks.

could we split this up a bit instead?

If everything goes through your tree, we'll end up with a lot of conflicts with 
other pending stuff, so I'd really appreciate if you could leave out patches
 
   patch2: define clock ID used for GMAC
   patch3: modify CRU config for Rockchip RK3288 SoCs integrated GMAC
   patch4: dts: rockchip: add gmac info for rk3288
   patch5: dts: rockchip: enable gmac on RK3288 evb board

so only take the driver itself and the dt-binding and I would take these 4 
above through the appropriate trees (clk and arm-soc)


Thanks and happy new year
Heiko

Re: [PATCH v3 0/6] support GMAC driver for RK3288

[David Miller]

From: Heiko Stübner <heiko@sntech.de>
Date: Thu, 01 Jan 2015 03:06:31 +0100

> Hi David,
> 
> Am Mittwoch, 31. Dezember 2014, 19:15:38 schrieb David Miller:
>> From: Roger Chen <roger.chen@rock-chips.com>
>> Date: Mon, 29 Dec 2014 17:42:32 +0800
>> 
>> > Roger Chen (6):
>> >   patch1: add driver for Rockchip RK3288 SoCs integrated GMAC
>> >   patch2: define clock ID used for GMAC
>> >   patch3: modify CRU config for Rockchip RK3288 SoCs integrated GMAC
>> >   patch4: dts: rockchip: add gmac info for rk3288
>> >   patch5: dts: rockchip: enable gmac on RK3288 evb board
>> >   patch6: add document for Rockchip RK3288 GMAC
>> > 
>> > Tested on rk3288 evb board:
>> > Execute the following command to enable ethernet,
>> > set local IP and ping a remote host.
>> > 
>> > busybox ifconfig eth0 up
>> > busybox ifconfig eth0 192.168.1.111
>> > ping 192.168.1.1
>> 
>> Series applied to net-next, thanks.
> 
> could we split this up a bit instead?

Too late, what's in my tree is in the permanent commit history
and cannot be deleted.

Re: [PATCH v3 0/6] support GMAC driver for RK3288

[Heiko Stübner]

Am Donnerstag, 1. Januar 2015, 21:01:22 schrieb David Miller:
> From: Heiko Stübner <heiko@sntech.de>
> Date: Thu, 01 Jan 2015 03:06:31 +0100
> 
> > Hi David,
> > 
> > Am Mittwoch, 31. Dezember 2014, 19:15:38 schrieb David Miller:
> >> From: Roger Chen <roger.chen@rock-chips.com>
> >> Date: Mon, 29 Dec 2014 17:42:32 +0800
> >> 
> >> > Roger Chen (6):
> >> >   patch1: add driver for Rockchip RK3288 SoCs integrated GMAC
> >> >   patch2: define clock ID used for GMAC
> >> >   patch3: modify CRU config for Rockchip RK3288 SoCs integrated GMAC
> >> >   patch4: dts: rockchip: add gmac info for rk3288
> >> >   patch5: dts: rockchip: enable gmac on RK3288 evb board
> >> >   patch6: add document for Rockchip RK3288 GMAC
> >> > 
> >> > Tested on rk3288 evb board:
> >> > Execute the following command to enable ethernet,
> >> > set local IP and ping a remote host.
> >> > 
> >> > busybox ifconfig eth0 up
> >> > busybox ifconfig eth0 192.168.1.111
> >> > ping 192.168.1.1
> >> 
> >> Series applied to net-next, thanks.
> > 
> > could we split this up a bit instead?
> 
> Too late, what's in my tree is in the permanent commit history
> and cannot be deleted.

ok no problem ... I'll work around it then so that any possible conflicts are 
easily solvable.


Heiko