* [PATCH net-next 1/9] be2net: move un-exported routines from be.h to respective src files
2015-02-06 13:18 [PATCH net-next 0/9] be2net: patch set Sathya Perla
@ 2015-02-06 13:18 ` Sathya Perla
2015-02-06 13:18 ` [PATCH net-next 2/9] be2net: replace (1 << x) with BIT(x) Sathya Perla
` (8 subsequent siblings)
9 siblings, 0 replies; 14+ messages in thread
From: Sathya Perla @ 2015-02-06 13:18 UTC (permalink / raw)
To: netdev
Routines that are called only inside one src file must remain in that
file itself. Including them in a header file that is used for exporting
routine/struct definitions, causes unnecessary compilation of other
src files, when such a routine is modified.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
---
drivers/net/ethernet/emulex/benet/be.h | 166 ----------------------------
drivers/net/ethernet/emulex/benet/be_cmds.c | 18 +++
drivers/net/ethernet/emulex/benet/be_main.c | 149 +++++++++++++++++++++++++
3 files changed, 167 insertions(+), 166 deletions(-)
diff --git a/drivers/net/ethernet/emulex/benet/be.h b/drivers/net/ethernet/emulex/benet/be.h
index 9fa2569..3b1d59d 100644
--- a/drivers/net/ethernet/emulex/benet/be.h
+++ b/drivers/net/ethernet/emulex/benet/be.h
@@ -59,26 +59,6 @@
#define OC_SUBSYS_DEVICE_ID3 0xE612
#define OC_SUBSYS_DEVICE_ID4 0xE652
-static inline char *nic_name(struct pci_dev *pdev)
-{
- switch (pdev->device) {
- case OC_DEVICE_ID1:
- return OC_NAME;
- case OC_DEVICE_ID2:
- return OC_NAME_BE;
- case OC_DEVICE_ID3:
- case OC_DEVICE_ID4:
- return OC_NAME_LANCER;
- case BE_DEVICE_ID2:
- return BE3_NAME;
- case OC_DEVICE_ID5:
- case OC_DEVICE_ID6:
- return OC_NAME_SH;
- default:
- return BE_NAME;
- }
-}
-
/* Number of bytes of an RX frame that are copied to skb->data */
#define BE_HDR_LEN ((u16) 64)
/* allocate extra space to allow tunneling decapsulation without head reallocation */
@@ -734,19 +714,6 @@ static inline bool is_ipv4_pkt(struct sk_buff *skb)
return skb->protocol == htons(ETH_P_IP) && ip_hdr(skb)->version == 4;
}
-static inline void be_vf_eth_addr_generate(struct be_adapter *adapter, u8 *mac)
-{
- u32 addr;
-
- addr = jhash(adapter->netdev->dev_addr, ETH_ALEN, 0);
-
- mac[5] = (u8)(addr & 0xFF);
- mac[4] = (u8)((addr >> 8) & 0xFF);
- mac[3] = (u8)((addr >> 16) & 0xFF);
- /* Use the OUI from the current MAC address */
- memcpy(mac, adapter->netdev->dev_addr, 3);
-}
-
static inline bool be_multi_rxq(const struct be_adapter *adapter)
{
return adapter->num_rx_qs > 1;
@@ -769,129 +736,6 @@ static inline void be_clear_all_error(struct be_adapter *adapter)
adapter->fw_timeout = false;
}
-static inline bool be_is_wol_excluded(struct be_adapter *adapter)
-{
- struct pci_dev *pdev = adapter->pdev;
-
- if (!be_physfn(adapter))
- return true;
-
- switch (pdev->subsystem_device) {
- case OC_SUBSYS_DEVICE_ID1:
- case OC_SUBSYS_DEVICE_ID2:
- case OC_SUBSYS_DEVICE_ID3:
- case OC_SUBSYS_DEVICE_ID4:
- return true;
- default:
- return false;
- }
-}
-
-static inline int qnq_async_evt_rcvd(struct be_adapter *adapter)
-{
- return adapter->flags & BE_FLAGS_QNQ_ASYNC_EVT_RCVD;
-}
-
-#ifdef CONFIG_NET_RX_BUSY_POLL
-static inline bool be_lock_napi(struct be_eq_obj *eqo)
-{
- bool status = true;
-
- spin_lock(&eqo->lock); /* BH is already disabled */
- if (eqo->state & BE_EQ_LOCKED) {
- WARN_ON(eqo->state & BE_EQ_NAPI);
- eqo->state |= BE_EQ_NAPI_YIELD;
- status = false;
- } else {
- eqo->state = BE_EQ_NAPI;
- }
- spin_unlock(&eqo->lock);
- return status;
-}
-
-static inline void be_unlock_napi(struct be_eq_obj *eqo)
-{
- spin_lock(&eqo->lock); /* BH is already disabled */
-
- WARN_ON(eqo->state & (BE_EQ_POLL | BE_EQ_NAPI_YIELD));
- eqo->state = BE_EQ_IDLE;
-
- spin_unlock(&eqo->lock);
-}
-
-static inline bool be_lock_busy_poll(struct be_eq_obj *eqo)
-{
- bool status = true;
-
- spin_lock_bh(&eqo->lock);
- if (eqo->state & BE_EQ_LOCKED) {
- eqo->state |= BE_EQ_POLL_YIELD;
- status = false;
- } else {
- eqo->state |= BE_EQ_POLL;
- }
- spin_unlock_bh(&eqo->lock);
- return status;
-}
-
-static inline void be_unlock_busy_poll(struct be_eq_obj *eqo)
-{
- spin_lock_bh(&eqo->lock);
-
- WARN_ON(eqo->state & (BE_EQ_NAPI));
- eqo->state = BE_EQ_IDLE;
-
- spin_unlock_bh(&eqo->lock);
-}
-
-static inline void be_enable_busy_poll(struct be_eq_obj *eqo)
-{
- spin_lock_init(&eqo->lock);
- eqo->state = BE_EQ_IDLE;
-}
-
-static inline void be_disable_busy_poll(struct be_eq_obj *eqo)
-{
- local_bh_disable();
-
- /* It's enough to just acquire napi lock on the eqo to stop
- * be_busy_poll() from processing any queueus.
- */
- while (!be_lock_napi(eqo))
- mdelay(1);
-
- local_bh_enable();
-}
-
-#else /* CONFIG_NET_RX_BUSY_POLL */
-
-static inline bool be_lock_napi(struct be_eq_obj *eqo)
-{
- return true;
-}
-
-static inline void be_unlock_napi(struct be_eq_obj *eqo)
-{
-}
-
-static inline bool be_lock_busy_poll(struct be_eq_obj *eqo)
-{
- return false;
-}
-
-static inline void be_unlock_busy_poll(struct be_eq_obj *eqo)
-{
-}
-
-static inline void be_enable_busy_poll(struct be_eq_obj *eqo)
-{
-}
-
-static inline void be_disable_busy_poll(struct be_eq_obj *eqo)
-{
-}
-#endif /* CONFIG_NET_RX_BUSY_POLL */
-
void be_cq_notify(struct be_adapter *adapter, u16 qid, bool arm,
u16 num_popped);
void be_link_status_update(struct be_adapter *adapter, u8 link_status);
@@ -900,16 +744,6 @@ int be_load_fw(struct be_adapter *adapter, u8 *func);
bool be_is_wol_supported(struct be_adapter *adapter);
bool be_pause_supported(struct be_adapter *adapter);
u32 be_get_fw_log_level(struct be_adapter *adapter);
-
-static inline int fw_major_num(const char *fw_ver)
-{
- int fw_major = 0;
-
- sscanf(fw_ver, "%d.", &fw_major);
-
- return fw_major;
-}
-
int be_update_queues(struct be_adapter *adapter);
int be_poll(struct napi_struct *napi, int budget);
diff --git a/drivers/net/ethernet/emulex/benet/be_cmds.c b/drivers/net/ethernet/emulex/benet/be_cmds.c
index 4bd425e..3a10145 100644
--- a/drivers/net/ethernet/emulex/benet/be_cmds.c
+++ b/drivers/net/ethernet/emulex/benet/be_cmds.c
@@ -3241,6 +3241,24 @@ err:
return status;
}
+static bool be_is_wol_excluded(struct be_adapter *adapter)
+{
+ struct pci_dev *pdev = adapter->pdev;
+
+ if (!be_physfn(adapter))
+ return true;
+
+ switch (pdev->subsystem_device) {
+ case OC_SUBSYS_DEVICE_ID1:
+ case OC_SUBSYS_DEVICE_ID2:
+ case OC_SUBSYS_DEVICE_ID3:
+ case OC_SUBSYS_DEVICE_ID4:
+ return true;
+ default:
+ return false;
+ }
+}
+
int be_cmd_get_acpi_wol_cap(struct be_adapter *adapter)
{
struct be_mcc_wrb *wrb;
diff --git a/drivers/net/ethernet/emulex/benet/be_main.c b/drivers/net/ethernet/emulex/benet/be_main.c
index 598c507..4231a70 100644
--- a/drivers/net/ethernet/emulex/benet/be_main.c
+++ b/drivers/net/ethernet/emulex/benet/be_main.c
@@ -854,6 +854,11 @@ dma_err:
return 0;
}
+static inline int qnq_async_evt_rcvd(struct be_adapter *adapter)
+{
+ return adapter->flags & BE_FLAGS_QNQ_ASYNC_EVT_RCVD;
+}
+
static struct sk_buff *be_insert_vlan_in_pkt(struct be_adapter *adapter,
struct sk_buff *skb,
bool *skip_hw_vlan)
@@ -2526,6 +2531,106 @@ static void be_process_tx(struct be_adapter *adapter, struct be_tx_obj *txo,
}
}
+#ifdef CONFIG_NET_RX_BUSY_POLL
+static inline bool be_lock_napi(struct be_eq_obj *eqo)
+{
+ bool status = true;
+
+ spin_lock(&eqo->lock); /* BH is already disabled */
+ if (eqo->state & BE_EQ_LOCKED) {
+ WARN_ON(eqo->state & BE_EQ_NAPI);
+ eqo->state |= BE_EQ_NAPI_YIELD;
+ status = false;
+ } else {
+ eqo->state = BE_EQ_NAPI;
+ }
+ spin_unlock(&eqo->lock);
+ return status;
+}
+
+static inline void be_unlock_napi(struct be_eq_obj *eqo)
+{
+ spin_lock(&eqo->lock); /* BH is already disabled */
+
+ WARN_ON(eqo->state & (BE_EQ_POLL | BE_EQ_NAPI_YIELD));
+ eqo->state = BE_EQ_IDLE;
+
+ spin_unlock(&eqo->lock);
+}
+
+static inline bool be_lock_busy_poll(struct be_eq_obj *eqo)
+{
+ bool status = true;
+
+ spin_lock_bh(&eqo->lock);
+ if (eqo->state & BE_EQ_LOCKED) {
+ eqo->state |= BE_EQ_POLL_YIELD;
+ status = false;
+ } else {
+ eqo->state |= BE_EQ_POLL;
+ }
+ spin_unlock_bh(&eqo->lock);
+ return status;
+}
+
+static inline void be_unlock_busy_poll(struct be_eq_obj *eqo)
+{
+ spin_lock_bh(&eqo->lock);
+
+ WARN_ON(eqo->state & (BE_EQ_NAPI));
+ eqo->state = BE_EQ_IDLE;
+
+ spin_unlock_bh(&eqo->lock);
+}
+
+static inline void be_enable_busy_poll(struct be_eq_obj *eqo)
+{
+ spin_lock_init(&eqo->lock);
+ eqo->state = BE_EQ_IDLE;
+}
+
+static inline void be_disable_busy_poll(struct be_eq_obj *eqo)
+{
+ local_bh_disable();
+
+ /* It's enough to just acquire napi lock on the eqo to stop
+ * be_busy_poll() from processing any queueus.
+ */
+ while (!be_lock_napi(eqo))
+ mdelay(1);
+
+ local_bh_enable();
+}
+
+#else /* CONFIG_NET_RX_BUSY_POLL */
+
+static inline bool be_lock_napi(struct be_eq_obj *eqo)
+{
+ return true;
+}
+
+static inline void be_unlock_napi(struct be_eq_obj *eqo)
+{
+}
+
+static inline bool be_lock_busy_poll(struct be_eq_obj *eqo)
+{
+ return false;
+}
+
+static inline void be_unlock_busy_poll(struct be_eq_obj *eqo)
+{
+}
+
+static inline void be_enable_busy_poll(struct be_eq_obj *eqo)
+{
+}
+
+static inline void be_disable_busy_poll(struct be_eq_obj *eqo)
+{
+}
+#endif /* CONFIG_NET_RX_BUSY_POLL */
+
int be_poll(struct napi_struct *napi, int budget)
{
struct be_eq_obj *eqo = container_of(napi, struct be_eq_obj, napi);
@@ -3020,6 +3125,19 @@ static int be_setup_wol(struct be_adapter *adapter, bool enable)
return status;
}
+static void be_vf_eth_addr_generate(struct be_adapter *adapter, u8 *mac)
+{
+ u32 addr;
+
+ addr = jhash(adapter->netdev->dev_addr, ETH_ALEN, 0);
+
+ mac[5] = (u8)(addr & 0xFF);
+ mac[4] = (u8)((addr >> 8) & 0xFF);
+ mac[3] = (u8)((addr >> 16) & 0xFF);
+ /* Use the OUI from the current MAC address */
+ memcpy(mac, adapter->netdev->dev_addr, 3);
+}
+
/*
* Generate a seed MAC address from the PF MAC Address using jhash.
* MAC Address for VFs are assigned incrementally starting from the seed.
@@ -3664,6 +3782,17 @@ int be_update_queues(struct be_adapter *adapter)
return status;
}
+static inline int fw_major_num(const char *fw_ver)
+{
+ int fw_major = 0, i;
+
+ i = sscanf(fw_ver, "%d.", &fw_major);
+ if (i != 1)
+ return 0;
+
+ return fw_major;
+}
+
static int be_setup(struct be_adapter *adapter)
{
struct device *dev = &adapter->pdev->dev;
@@ -4939,6 +5068,26 @@ static inline char *func_name(struct be_adapter *adapter)
return be_physfn(adapter) ? "PF" : "VF";
}
+static inline char *nic_name(struct pci_dev *pdev)
+{
+ switch (pdev->device) {
+ case OC_DEVICE_ID1:
+ return OC_NAME;
+ case OC_DEVICE_ID2:
+ return OC_NAME_BE;
+ case OC_DEVICE_ID3:
+ case OC_DEVICE_ID4:
+ return OC_NAME_LANCER;
+ case BE_DEVICE_ID2:
+ return BE3_NAME;
+ case OC_DEVICE_ID5:
+ case OC_DEVICE_ID6:
+ return OC_NAME_SH;
+ default:
+ return BE_NAME;
+ }
+}
+
static int be_probe(struct pci_dev *pdev, const struct pci_device_id *pdev_id)
{
int status = 0;
--
2.2.0
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH net-next 2/9] be2net: replace (1 << x) with BIT(x)
2015-02-06 13:18 [PATCH net-next 0/9] be2net: patch set Sathya Perla
2015-02-06 13:18 ` [PATCH net-next 1/9] be2net: move un-exported routines from be.h to respective src files Sathya Perla
@ 2015-02-06 13:18 ` Sathya Perla
2015-02-16 12:09 ` Sergei Shtylyov
2015-02-06 13:18 ` [PATCH net-next 3/9] be2net: refactor code that checks flash file compatibility Sathya Perla
` (7 subsequent siblings)
9 siblings, 1 reply; 14+ messages in thread
From: Sathya Perla @ 2015-02-06 13:18 UTC (permalink / raw)
To: netdev
From: Vasundhara Volam <vasundhara.volam@emulex.com>
BIT(x) is the preffered usage.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
---
drivers/net/ethernet/emulex/benet/be.h | 18 +++++++++---------
drivers/net/ethernet/emulex/benet/be_cmds.h | 8 ++++----
drivers/net/ethernet/emulex/benet/be_hw.h | 4 ++--
3 files changed, 15 insertions(+), 15 deletions(-)
diff --git a/drivers/net/ethernet/emulex/benet/be.h b/drivers/net/ethernet/emulex/benet/be.h
index 3b1d59d..9869556 100644
--- a/drivers/net/ethernet/emulex/benet/be.h
+++ b/drivers/net/ethernet/emulex/benet/be.h
@@ -361,15 +361,15 @@ enum vf_state {
ASSIGNED = 1
};
-#define BE_FLAGS_LINK_STATUS_INIT 1
-#define BE_FLAGS_SRIOV_ENABLED (1 << 2)
-#define BE_FLAGS_WORKER_SCHEDULED (1 << 3)
-#define BE_FLAGS_VLAN_PROMISC (1 << 4)
-#define BE_FLAGS_MCAST_PROMISC (1 << 5)
-#define BE_FLAGS_NAPI_ENABLED (1 << 9)
-#define BE_FLAGS_QNQ_ASYNC_EVT_RCVD (1 << 11)
-#define BE_FLAGS_VXLAN_OFFLOADS (1 << 12)
-#define BE_FLAGS_SETUP_DONE (1 << 13)
+#define BE_FLAGS_LINK_STATUS_INIT BIT(1)
+#define BE_FLAGS_SRIOV_ENABLED BIT(2)
+#define BE_FLAGS_WORKER_SCHEDULED BIT(3)
+#define BE_FLAGS_VLAN_PROMISC BIT(4)
+#define BE_FLAGS_MCAST_PROMISC BIT(5)
+#define BE_FLAGS_NAPI_ENABLED BIT(6)
+#define BE_FLAGS_QNQ_ASYNC_EVT_RCVD BIT(7)
+#define BE_FLAGS_VXLAN_OFFLOADS BIT(8)
+#define BE_FLAGS_SETUP_DONE BIT(9)
#define BE_UC_PMAC_COUNT 30
#define BE_VF_UC_PMAC_COUNT 2
diff --git a/drivers/net/ethernet/emulex/benet/be_cmds.h b/drivers/net/ethernet/emulex/benet/be_cmds.h
index c2701cc..c231e45 100644
--- a/drivers/net/ethernet/emulex/benet/be_cmds.h
+++ b/drivers/net/ethernet/emulex/benet/be_cmds.h
@@ -44,10 +44,10 @@ struct be_mcc_wrb {
} payload;
};
-#define CQE_FLAGS_VALID_MASK (1 << 31)
-#define CQE_FLAGS_ASYNC_MASK (1 << 30)
-#define CQE_FLAGS_COMPLETED_MASK (1 << 28)
-#define CQE_FLAGS_CONSUMED_MASK (1 << 27)
+#define CQE_FLAGS_VALID_MASK BIT(31)
+#define CQE_FLAGS_ASYNC_MASK BIT(30)
+#define CQE_FLAGS_COMPLETED_MASK BIT(28)
+#define CQE_FLAGS_CONSUMED_MASK BIT(27)
/* Completion Status */
enum mcc_base_status {
diff --git a/drivers/net/ethernet/emulex/benet/be_hw.h b/drivers/net/ethernet/emulex/benet/be_hw.h
index 8e91ae8..a8593aa 100644
--- a/drivers/net/ethernet/emulex/benet/be_hw.h
+++ b/drivers/net/ethernet/emulex/benet/be_hw.h
@@ -75,7 +75,7 @@
* atomically without having to arbitrate for the PCI Interrupt Disable bit
* with the OS.
*/
-#define MEMBAR_CTRL_INT_CTRL_HOSTINTR_MASK (1 << 29) /* bit 29 */
+#define MEMBAR_CTRL_INT_CTRL_HOSTINTR_MASK BIT(29) /* bit 29 */
/********* PCI Function Capability *********/
#define BE_FUNCTION_CAPS_RSS 0x2
@@ -224,7 +224,7 @@ struct amap_eth_hdr_wrb {
} __packed;
#define TX_HDR_WRB_COMPL 1 /* word 2 */
-#define TX_HDR_WRB_EVT (1 << 1) /* word 2 */
+#define TX_HDR_WRB_EVT BIT(1) /* word 2 */
#define TX_HDR_WRB_NUM_SHIFT 13 /* word 2: bits 13:17 */
#define TX_HDR_WRB_NUM_MASK 0x1F /* word 2: bits 13:17 */
--
2.2.0
^ permalink raw reply related [flat|nested] 14+ messages in thread* Re: [PATCH net-next 2/9] be2net: replace (1 << x) with BIT(x)
2015-02-06 13:18 ` [PATCH net-next 2/9] be2net: replace (1 << x) with BIT(x) Sathya Perla
@ 2015-02-16 12:09 ` Sergei Shtylyov
2015-02-16 12:55 ` Sathya Perla
0 siblings, 1 reply; 14+ messages in thread
From: Sergei Shtylyov @ 2015-02-16 12:09 UTC (permalink / raw)
To: Sathya Perla, netdev
Hello.
On 2/6/2015 4:18 PM, Sathya Perla wrote:
> From: Vasundhara Volam <vasundhara.volam@emulex.com>
> BIT(x) is the preffered usage.
Preferred.
> Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
> Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
[...]
> diff --git a/drivers/net/ethernet/emulex/benet/be.h b/drivers/net/ethernet/emulex/benet/be.h
> index 3b1d59d..9869556 100644
> --- a/drivers/net/ethernet/emulex/benet/be.h
> +++ b/drivers/net/ethernet/emulex/benet/be.h
> @@ -361,15 +361,15 @@ enum vf_state {
> ASSIGNED = 1
> };
>
> -#define BE_FLAGS_LINK_STATUS_INIT 1
> -#define BE_FLAGS_SRIOV_ENABLED (1 << 2)
> -#define BE_FLAGS_WORKER_SCHEDULED (1 << 3)
> -#define BE_FLAGS_VLAN_PROMISC (1 << 4)
> -#define BE_FLAGS_MCAST_PROMISC (1 << 5)
> -#define BE_FLAGS_NAPI_ENABLED (1 << 9)
> -#define BE_FLAGS_QNQ_ASYNC_EVT_RCVD (1 << 11)
> -#define BE_FLAGS_VXLAN_OFFLOADS (1 << 12)
> -#define BE_FLAGS_SETUP_DONE (1 << 13)
> +#define BE_FLAGS_LINK_STATUS_INIT BIT(1)
Not BIT(0)?
> +#define BE_FLAGS_SRIOV_ENABLED BIT(2)
> +#define BE_FLAGS_WORKER_SCHEDULED BIT(3)
> +#define BE_FLAGS_VLAN_PROMISC BIT(4)
> +#define BE_FLAGS_MCAST_PROMISC BIT(5)
> +#define BE_FLAGS_NAPI_ENABLED BIT(6)
> +#define BE_FLAGS_QNQ_ASYNC_EVT_RCVD BIT(7)
> +#define BE_FLAGS_VXLAN_OFFLOADS BIT(8)
> +#define BE_FLAGS_SETUP_DONE BIT(9)
So, you decided to renumber the bits?
[...]
WBR, Sergei
^ permalink raw reply [flat|nested] 14+ messages in thread* RE: [PATCH net-next 2/9] be2net: replace (1 << x) with BIT(x)
2015-02-16 12:09 ` Sergei Shtylyov
@ 2015-02-16 12:55 ` Sathya Perla
2015-02-16 13:13 ` Sergei Shtylyov
0 siblings, 1 reply; 14+ messages in thread
From: Sathya Perla @ 2015-02-16 12:55 UTC (permalink / raw)
To: Sergei Shtylyov, netdev@vger.kernel.org
> -----Original Message-----
> From: Sergei Shtylyov [mailto:sergei.shtylyov@cogentembedded.com]
>
> Hello.
>
> On 2/6/2015 4:18 PM, Sathya Perla wrote:
>
> > From: Vasundhara Volam <vasundhara.volam@emulex.com>
>
> > BIT(x) is the preffered usage.
>
> Preferred.
:-) As this is a harmless spelling mistake only in the changelog,
I'll not bother sending a new patch for this!
>
> [...]
>
> > diff --git a/drivers/net/ethernet/emulex/benet/be.h
> b/drivers/net/ethernet/emulex/benet/be.h
> > index 3b1d59d..9869556 100644
> > --- a/drivers/net/ethernet/emulex/benet/be.h
> > +++ b/drivers/net/ethernet/emulex/benet/be.h
> > @@ -361,15 +361,15 @@ enum vf_state {
> > ASSIGNED = 1
> > };
> >
> > -#define BE_FLAGS_LINK_STATUS_INIT 1
> > -#define BE_FLAGS_SRIOV_ENABLED (1 << 2)
> > -#define BE_FLAGS_WORKER_SCHEDULED (1 << 3)
> > -#define BE_FLAGS_VLAN_PROMISC (1 << 4)
> > -#define BE_FLAGS_MCAST_PROMISC (1 << 5)
> > -#define BE_FLAGS_NAPI_ENABLED (1 << 9)
> > -#define BE_FLAGS_QNQ_ASYNC_EVT_RCVD (1 << 11)
> > -#define BE_FLAGS_VXLAN_OFFLOADS (1 << 12)
> > -#define BE_FLAGS_SETUP_DONE (1 << 13)
> > +#define BE_FLAGS_LINK_STATUS_INIT BIT(1)
>
> Not BIT(0)?
Huh, this was not intentional. I'll remember to use bit-0 the next time
we introduce a new bit!
>
> > +#define BE_FLAGS_SRIOV_ENABLED BIT(2)
> > +#define BE_FLAGS_WORKER_SCHEDULED BIT(3)
> > +#define BE_FLAGS_VLAN_PROMISC BIT(4)
> > +#define BE_FLAGS_MCAST_PROMISC BIT(5)
> > +#define BE_FLAGS_NAPI_ENABLED BIT(6)
> > +#define BE_FLAGS_QNQ_ASYNC_EVT_RCVD BIT(7)
> > +#define BE_FLAGS_VXLAN_OFFLOADS BIT(8)
> > +#define BE_FLAGS_SETUP_DONE BIT(9)
>
> So, you decided to renumber the bits?
Yes, some holes in the bit map were removed.
^ permalink raw reply [flat|nested] 14+ messages in thread* Re: [PATCH net-next 2/9] be2net: replace (1 << x) with BIT(x)
2015-02-16 12:55 ` Sathya Perla
@ 2015-02-16 13:13 ` Sergei Shtylyov
0 siblings, 0 replies; 14+ messages in thread
From: Sergei Shtylyov @ 2015-02-16 13:13 UTC (permalink / raw)
To: Sathya Perla, netdev@vger.kernel.org
Hello.
On 2/16/2015 3:55 PM, Sathya Perla wrote:
>>> From: Vasundhara Volam <vasundhara.volam@emulex.com>
>>> BIT(x) is the preffered usage.
>> Preferred.
> :-) As this is a harmless spelling mistake only in the changelog,
> I'll not bother sending a new patch for this!
OK...
>> [...]
>>> diff --git a/drivers/net/ethernet/emulex/benet/be.h
>> b/drivers/net/ethernet/emulex/benet/be.h
>>> index 3b1d59d..9869556 100644
>>> --- a/drivers/net/ethernet/emulex/benet/be.h
>>> +++ b/drivers/net/ethernet/emulex/benet/be.h
>>> @@ -361,15 +361,15 @@ enum vf_state {
>>> ASSIGNED = 1
>>> };
>>>
>>> -#define BE_FLAGS_LINK_STATUS_INIT 1
>>> -#define BE_FLAGS_SRIOV_ENABLED (1 << 2)
>>> -#define BE_FLAGS_WORKER_SCHEDULED (1 << 3)
>>> -#define BE_FLAGS_VLAN_PROMISC (1 << 4)
>>> -#define BE_FLAGS_MCAST_PROMISC (1 << 5)
>>> -#define BE_FLAGS_NAPI_ENABLED (1 << 9)
>>> -#define BE_FLAGS_QNQ_ASYNC_EVT_RCVD (1 << 11)
>>> -#define BE_FLAGS_VXLAN_OFFLOADS (1 << 12)
>>> -#define BE_FLAGS_SETUP_DONE (1 << 13)
>>> +#define BE_FLAGS_LINK_STATUS_INIT BIT(1)
>> Not BIT(0)?
> Huh, this was not intentional. I'll remember to use bit-0 the next time
> we introduce a new bit!
Note that bit 0 was used for BE_FLAGS_LINK_STATUS_INIT before your patch.
[...]
WBR, Sergei
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH net-next 3/9] be2net: refactor code that checks flash file compatibility
2015-02-06 13:18 [PATCH net-next 0/9] be2net: patch set Sathya Perla
2015-02-06 13:18 ` [PATCH net-next 1/9] be2net: move un-exported routines from be.h to respective src files Sathya Perla
2015-02-06 13:18 ` [PATCH net-next 2/9] be2net: replace (1 << x) with BIT(x) Sathya Perla
@ 2015-02-06 13:18 ` Sathya Perla
2015-02-06 13:18 ` [PATCH net-next 4/9] be2net: avoid flashing SH-B0 UFI image on SH-P2 chip Sathya Perla
` (6 subsequent siblings)
9 siblings, 0 replies; 14+ messages in thread
From: Sathya Perla @ 2015-02-06 13:18 UTC (permalink / raw)
To: netdev
From: Vasundhara Volam <vasundhara.volam@emulex.com>
This patch re-factors the code that checks for flash file compatibility with
the chip type, for better readability, as follows:
- be_get_ufi_type() returns the UFI type from the flash file
- be_check_ufi_compatibility() checks if the UFI type is compatible
with the adapter/chip that is being flashed
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
---
drivers/net/ethernet/emulex/benet/be_cmds.h | 8 ++
drivers/net/ethernet/emulex/benet/be_main.c | 138 ++++++++++++++--------------
2 files changed, 78 insertions(+), 68 deletions(-)
diff --git a/drivers/net/ethernet/emulex/benet/be_cmds.h b/drivers/net/ethernet/emulex/benet/be_cmds.h
index c231e45..bed4a32 100644
--- a/drivers/net/ethernet/emulex/benet/be_cmds.h
+++ b/drivers/net/ethernet/emulex/benet/be_cmds.h
@@ -1091,6 +1091,9 @@ struct be_cmd_req_query_fw_cfg {
u32 rsvd[31];
};
+/* ASIC revisions */
+#define ASIC_REV_B0 0x10
+
struct be_cmd_resp_query_fw_cfg {
struct be_cmd_resp_hdr hdr;
u32 be_config_number;
@@ -1260,6 +1263,11 @@ struct flash_file_hdr_g2 {
u8 build[24];
};
+/* First letter of the build version of the image */
+#define BLD_STR_UFI_TYPE_BE2 '2'
+#define BLD_STR_UFI_TYPE_BE3 '3'
+#define BLD_STR_UFI_TYPE_SH '4'
+
struct flash_file_hdr_g3 {
u8 sign[52];
u8 ufi_version[4];
diff --git a/drivers/net/ethernet/emulex/benet/be_main.c b/drivers/net/ethernet/emulex/benet/be_main.c
index 4231a70..ddc5966 100644
--- a/drivers/net/ethernet/emulex/benet/be_main.c
+++ b/drivers/net/ethernet/emulex/benet/be_main.c
@@ -4058,6 +4058,7 @@ static int be_flash_BEx(struct be_adapter *adapter,
pflashcomp = gen2_flash_types;
filehdr_size = sizeof(struct flash_file_hdr_g2);
num_comp = ARRAY_SIZE(gen2_flash_types);
+ img_hdrs_size = 0;
}
/* Get flash section info*/
@@ -4331,98 +4332,99 @@ static int lancer_fw_download(struct be_adapter *adapter,
return 0;
}
-#define UFI_TYPE2 2
-#define UFI_TYPE3 3
-#define UFI_TYPE3R 10
-#define UFI_TYPE4 4
+#define BE2_UFI 2
+#define BE3_UFI 3
+#define BE3R_UFI 10
+#define SH_UFI 4
+
static int be_get_ufi_type(struct be_adapter *adapter,
struct flash_file_hdr_g3 *fhdr)
{
- if (!fhdr)
- goto be_get_ufi_exit;
+ if (!fhdr) {
+ dev_err(&adapter->pdev->dev, "Invalid FW UFI file");
+ return -1;
+ }
- if (skyhawk_chip(adapter) && fhdr->build[0] == '4')
- return UFI_TYPE4;
- else if (BE3_chip(adapter) && fhdr->build[0] == '3') {
- if (fhdr->asic_type_rev == 0x10)
- return UFI_TYPE3R;
- else
- return UFI_TYPE3;
- } else if (BE2_chip(adapter) && fhdr->build[0] == '2')
- return UFI_TYPE2;
+ /* First letter of the build version is used to identify
+ * which chip this image file is meant for.
+ */
+ switch (fhdr->build[0]) {
+ case BLD_STR_UFI_TYPE_SH:
+ return SH_UFI;
+ case BLD_STR_UFI_TYPE_BE3:
+ return (fhdr->asic_type_rev == ASIC_REV_B0) ? BE3R_UFI :
+ BE3_UFI;
+ case BLD_STR_UFI_TYPE_BE2:
+ return BE2_UFI;
+ default:
+ return -1;
+ }
+}
-be_get_ufi_exit:
- dev_err(&adapter->pdev->dev,
- "UFI and Interface are not compatible for flashing\n");
- return -1;
+/* Check if the flash image file is compatible with the adapter that
+ * is being flashed.
+ * BE3 chips with asic-rev B0 must be flashed only with BE3R_UFI type.
+ */
+static bool be_check_ufi_compatibility(struct be_adapter *adapter,
+ struct flash_file_hdr_g3 *fhdr)
+{
+ int ufi_type = be_get_ufi_type(adapter, fhdr);
+
+ switch (ufi_type) {
+ case SH_UFI:
+ return skyhawk_chip(adapter);
+ case BE3R_UFI:
+ return BE3_chip(adapter);
+ case BE3_UFI:
+ return (BE3_chip(adapter) && adapter->asic_rev < ASIC_REV_B0);
+ case BE2_UFI:
+ return BE2_chip(adapter);
+ default:
+ return false;
+ }
}
static int be_fw_download(struct be_adapter *adapter, const struct firmware* fw)
{
+ struct device *dev = &adapter->pdev->dev;
struct flash_file_hdr_g3 *fhdr3;
- struct image_hdr *img_hdr_ptr = NULL;
+ struct image_hdr *img_hdr_ptr;
+ int status = 0, i, num_imgs;
struct be_dma_mem flash_cmd;
- const u8 *p;
- int status = 0, i = 0, num_imgs = 0, ufi_type = 0;
- flash_cmd.size = sizeof(struct be_cmd_write_flashrom);
- flash_cmd.va = dma_alloc_coherent(&adapter->pdev->dev, flash_cmd.size,
- &flash_cmd.dma, GFP_KERNEL);
- if (!flash_cmd.va) {
- status = -ENOMEM;
- goto be_fw_exit;
+ fhdr3 = (struct flash_file_hdr_g3 *)fw->data;
+ if (!be_check_ufi_compatibility(adapter, fhdr3)) {
+ dev_err(dev, "Flash image is not compatible with adapter\n");
+ return -EINVAL;
}
- p = fw->data;
- fhdr3 = (struct flash_file_hdr_g3 *)p;
-
- ufi_type = be_get_ufi_type(adapter, fhdr3);
+ flash_cmd.size = sizeof(struct be_cmd_write_flashrom);
+ flash_cmd.va = dma_alloc_coherent(dev, flash_cmd.size, &flash_cmd.dma,
+ GFP_KERNEL);
+ if (!flash_cmd.va)
+ return -ENOMEM;
num_imgs = le32_to_cpu(fhdr3->num_imgs);
for (i = 0; i < num_imgs; i++) {
img_hdr_ptr = (struct image_hdr *)(fw->data +
(sizeof(struct flash_file_hdr_g3) +
i * sizeof(struct image_hdr)));
- if (le32_to_cpu(img_hdr_ptr->imageid) == 1) {
- switch (ufi_type) {
- case UFI_TYPE4:
- status = be_flash_skyhawk(adapter, fw,
- &flash_cmd, num_imgs);
- break;
- case UFI_TYPE3R:
- status = be_flash_BEx(adapter, fw, &flash_cmd,
- num_imgs);
- break;
- case UFI_TYPE3:
- /* Do not flash this ufi on BE3-R cards */
- if (adapter->asic_rev < 0x10)
- status = be_flash_BEx(adapter, fw,
- &flash_cmd,
- num_imgs);
- else {
- status = -EINVAL;
- dev_err(&adapter->pdev->dev,
- "Can't load BE3 UFI on BE3R\n");
- }
- }
- }
- }
-
- if (ufi_type == UFI_TYPE2)
- status = be_flash_BEx(adapter, fw, &flash_cmd, 0);
- else if (ufi_type == -1)
- status = -EINVAL;
+ if (!BE2_chip(adapter) &&
+ le32_to_cpu(img_hdr_ptr->imageid) != 1)
+ continue;
- dma_free_coherent(&adapter->pdev->dev, flash_cmd.size, flash_cmd.va,
- flash_cmd.dma);
- if (status) {
- dev_err(&adapter->pdev->dev, "Firmware load error\n");
- goto be_fw_exit;
+ if (skyhawk_chip(adapter))
+ status = be_flash_skyhawk(adapter, fw, &flash_cmd,
+ num_imgs);
+ else
+ status = be_flash_BEx(adapter, fw, &flash_cmd,
+ num_imgs);
}
- dev_info(&adapter->pdev->dev, "Firmware flashed successfully\n");
+ dma_free_coherent(dev, flash_cmd.size, flash_cmd.va, flash_cmd.dma);
+ if (!status)
+ dev_info(dev, "Firmware flashed successfully\n");
-be_fw_exit:
return status;
}
--
2.2.0
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH net-next 4/9] be2net: avoid flashing SH-B0 UFI image on SH-P2 chip
2015-02-06 13:18 [PATCH net-next 0/9] be2net: patch set Sathya Perla
` (2 preceding siblings ...)
2015-02-06 13:18 ` [PATCH net-next 3/9] be2net: refactor code that checks flash file compatibility Sathya Perla
@ 2015-02-06 13:18 ` Sathya Perla
2015-02-06 13:18 ` [PATCH net-next 5/9] be2net: use offset based FW flashing for Skyhawk chip Sathya Perla
` (5 subsequent siblings)
9 siblings, 0 replies; 14+ messages in thread
From: Sathya Perla @ 2015-02-06 13:18 UTC (permalink / raw)
To: netdev
From: Vasundhara Volam <vasundhara.volam@emulex.com>
Skyhawk-B0 FW UFI is not compatible to flash on Skyhawk-P2 ASIC.
But, Skyhawk-P2 FW UFI is compatible with both B0 and P2 chips.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
---
drivers/net/ethernet/emulex/benet/be_cmds.h | 1 +
drivers/net/ethernet/emulex/benet/be_main.c | 10 ++++++++--
2 files changed, 9 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/emulex/benet/be_cmds.h b/drivers/net/ethernet/emulex/benet/be_cmds.h
index bed4a32..774c5d1 100644
--- a/drivers/net/ethernet/emulex/benet/be_cmds.h
+++ b/drivers/net/ethernet/emulex/benet/be_cmds.h
@@ -1093,6 +1093,7 @@ struct be_cmd_req_query_fw_cfg {
/* ASIC revisions */
#define ASIC_REV_B0 0x10
+#define ASIC_REV_P2 0x11
struct be_cmd_resp_query_fw_cfg {
struct be_cmd_resp_hdr hdr;
diff --git a/drivers/net/ethernet/emulex/benet/be_main.c b/drivers/net/ethernet/emulex/benet/be_main.c
index ddc5966..9eaf8bc 100644
--- a/drivers/net/ethernet/emulex/benet/be_main.c
+++ b/drivers/net/ethernet/emulex/benet/be_main.c
@@ -4336,6 +4336,7 @@ static int lancer_fw_download(struct be_adapter *adapter,
#define BE3_UFI 3
#define BE3R_UFI 10
#define SH_UFI 4
+#define SH_P2_UFI 11
static int be_get_ufi_type(struct be_adapter *adapter,
struct flash_file_hdr_g3 *fhdr)
@@ -4350,7 +4351,8 @@ static int be_get_ufi_type(struct be_adapter *adapter,
*/
switch (fhdr->build[0]) {
case BLD_STR_UFI_TYPE_SH:
- return SH_UFI;
+ return (fhdr->asic_type_rev == ASIC_REV_P2) ? SH_P2_UFI :
+ SH_UFI;
case BLD_STR_UFI_TYPE_BE3:
return (fhdr->asic_type_rev == ASIC_REV_B0) ? BE3R_UFI :
BE3_UFI;
@@ -4364,6 +4366,7 @@ static int be_get_ufi_type(struct be_adapter *adapter,
/* Check if the flash image file is compatible with the adapter that
* is being flashed.
* BE3 chips with asic-rev B0 must be flashed only with BE3R_UFI type.
+ * Skyhawk chips with asic-rev P2 must be flashed only with SH_P2_UFI type.
*/
static bool be_check_ufi_compatibility(struct be_adapter *adapter,
struct flash_file_hdr_g3 *fhdr)
@@ -4371,8 +4374,11 @@ static bool be_check_ufi_compatibility(struct be_adapter *adapter,
int ufi_type = be_get_ufi_type(adapter, fhdr);
switch (ufi_type) {
- case SH_UFI:
+ case SH_P2_UFI:
return skyhawk_chip(adapter);
+ case SH_UFI:
+ return (skyhawk_chip(adapter) &&
+ adapter->asic_rev < ASIC_REV_P2);
case BE3R_UFI:
return BE3_chip(adapter);
case BE3_UFI:
--
2.2.0
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH net-next 5/9] be2net: use offset based FW flashing for Skyhawk chip
2015-02-06 13:18 [PATCH net-next 0/9] be2net: patch set Sathya Perla
` (3 preceding siblings ...)
2015-02-06 13:18 ` [PATCH net-next 4/9] be2net: avoid flashing SH-B0 UFI image on SH-P2 chip Sathya Perla
@ 2015-02-06 13:18 ` Sathya Perla
2015-02-06 13:18 ` [PATCH net-next 6/9] be2net: remove duplicate code in be_cmd_rx_filter() Sathya Perla
` (4 subsequent siblings)
9 siblings, 0 replies; 14+ messages in thread
From: Sathya Perla @ 2015-02-06 13:18 UTC (permalink / raw)
To: netdev
From: Vasundhara Volam <vasundhara.volam@emulex.com>
While sending FW update cmds to the FW, the driver specifies the "type"
of each component that needs to be flashed. The FW then picks the offset
in the flash area at which the componnet is to be flashed. This doesn't work
when new components that the current FW doesn't recognize, need to be
flashed. Recent FWs (10.2 and above) support a scheme of FW-update wherein
the "offset" of the component in the flash area can be specified instead
of the "type". This patch uses the "offset" based FW-update mechanism and
only when it fails, it fallsback to the old "type" based update.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
---
drivers/net/ethernet/emulex/benet/be_cmds.c | 18 +++++---
drivers/net/ethernet/emulex/benet/be_cmds.h | 6 ++-
drivers/net/ethernet/emulex/benet/be_main.c | 65 ++++++++++++++++++++++-------
3 files changed, 66 insertions(+), 23 deletions(-)
diff --git a/drivers/net/ethernet/emulex/benet/be_cmds.c b/drivers/net/ethernet/emulex/benet/be_cmds.c
index 3a10145..2f59553 100644
--- a/drivers/net/ethernet/emulex/benet/be_cmds.c
+++ b/drivers/net/ethernet/emulex/benet/be_cmds.c
@@ -2436,7 +2436,8 @@ err_unlock:
}
int be_cmd_write_flashrom(struct be_adapter *adapter, struct be_dma_mem *cmd,
- u32 flash_type, u32 flash_opcode, u32 buf_size)
+ u32 flash_type, u32 flash_opcode, u32 img_offset,
+ u32 buf_size)
{
struct be_mcc_wrb *wrb;
struct be_cmd_write_flashrom *req;
@@ -2457,6 +2458,9 @@ int be_cmd_write_flashrom(struct be_adapter *adapter, struct be_dma_mem *cmd,
cmd);
req->params.op_type = cpu_to_le32(flash_type);
+ if (flash_type == OPTYPE_OFFSET_SPECIFIED)
+ req->params.offset = cpu_to_le32(img_offset);
+
req->params.op_code = cpu_to_le32(flash_opcode);
req->params.data_buf_size = cpu_to_le32(buf_size);
@@ -2477,10 +2481,10 @@ err_unlock:
}
int be_cmd_get_flash_crc(struct be_adapter *adapter, u8 *flashed_crc,
- u16 optype, int offset)
+ u16 img_optype, u32 img_offset, u32 crc_offset)
{
- struct be_mcc_wrb *wrb;
struct be_cmd_read_flash_crc *req;
+ struct be_mcc_wrb *wrb;
int status;
spin_lock_bh(&adapter->mcc_lock);
@@ -2496,9 +2500,13 @@ int be_cmd_get_flash_crc(struct be_adapter *adapter, u8 *flashed_crc,
OPCODE_COMMON_READ_FLASHROM, sizeof(*req),
wrb, NULL);
- req->params.op_type = cpu_to_le32(optype);
+ req->params.op_type = cpu_to_le32(img_optype);
+ if (img_optype == OPTYPE_OFFSET_SPECIFIED)
+ req->params.offset = cpu_to_le32(img_offset + crc_offset);
+ else
+ req->params.offset = cpu_to_le32(crc_offset);
+
req->params.op_code = cpu_to_le32(FLASHROM_OPER_REPORT);
- req->params.offset = cpu_to_le32(offset);
req->params.data_buf_size = cpu_to_le32(0x4);
status = be_mcc_notify_wait(adapter);
diff --git a/drivers/net/ethernet/emulex/benet/be_cmds.h b/drivers/net/ethernet/emulex/benet/be_cmds.h
index 774c5d1..402d64f 100644
--- a/drivers/net/ethernet/emulex/benet/be_cmds.h
+++ b/drivers/net/ethernet/emulex/benet/be_cmds.h
@@ -1172,6 +1172,7 @@ struct be_cmd_resp_get_beacon_state {
#define OPTYPE_REDBOOT 1
#define OPTYPE_BIOS 2
#define OPTYPE_PXE_BIOS 3
+#define OPTYPE_OFFSET_SPECIFIED 7
#define OPTYPE_FCOE_BIOS 8
#define OPTYPE_ISCSI_BACKUP 9
#define OPTYPE_FCOE_FW_ACTIVE 10
@@ -2255,7 +2256,8 @@ int be_cmd_read_port_transceiver_data(struct be_adapter *adapter,
u8 page_num, u8 *data);
int be_cmd_query_cable_type(struct be_adapter *adapter);
int be_cmd_write_flashrom(struct be_adapter *adapter, struct be_dma_mem *cmd,
- u32 flash_oper, u32 flash_opcode, u32 buf_size);
+ u32 flash_oper, u32 flash_opcode, u32 img_offset,
+ u32 buf_size);
int lancer_cmd_write_object(struct be_adapter *adapter, struct be_dma_mem *cmd,
u32 data_size, u32 data_offset,
const char *obj_name, u32 *data_written,
@@ -2265,7 +2267,7 @@ int lancer_cmd_read_object(struct be_adapter *adapter, struct be_dma_mem *cmd,
u32 *data_read, u32 *eof, u8 *addn_status);
int lancer_cmd_delete_object(struct be_adapter *adapter, const char *obj_name);
int be_cmd_get_flash_crc(struct be_adapter *adapter, u8 *flashed_crc,
- u16 optype, int offset);
+ u16 img_optype, u32 img_offset, u32 crc_offset);
int be_cmd_enable_magic_wol(struct be_adapter *adapter, u8 *mac,
struct be_dma_mem *nonemb_cmd);
int be_cmd_fw_init(struct be_adapter *adapter);
diff --git a/drivers/net/ethernet/emulex/benet/be_main.c b/drivers/net/ethernet/emulex/benet/be_main.c
index 9eaf8bc..2ec1d80 100644
--- a/drivers/net/ethernet/emulex/benet/be_main.c
+++ b/drivers/net/ethernet/emulex/benet/be_main.c
@@ -3942,7 +3942,8 @@ static int be_check_flash_crc(struct be_adapter *adapter, const u8 *p,
int status;
u8 crc[4];
- status = be_cmd_get_flash_crc(adapter, crc, img_optype, img_size - 4);
+ status = be_cmd_get_flash_crc(adapter, crc, img_optype, img_offset,
+ img_size - 4);
if (status)
return status;
@@ -3958,13 +3959,13 @@ static int be_check_flash_crc(struct be_adapter *adapter, const u8 *p,
}
static int be_flash(struct be_adapter *adapter, const u8 *img,
- struct be_dma_mem *flash_cmd, int optype, int img_size)
+ struct be_dma_mem *flash_cmd, int optype, int img_size,
+ u32 img_offset)
{
+ u32 flash_op, num_bytes, total_bytes = img_size, bytes_sent = 0;
struct be_cmd_write_flashrom *req = flash_cmd->va;
- u32 total_bytes, flash_op, num_bytes;
int status;
- total_bytes = img_size;
while (total_bytes) {
num_bytes = min_t(u32, 32*1024, total_bytes);
@@ -3985,12 +3986,15 @@ static int be_flash(struct be_adapter *adapter, const u8 *img,
memcpy(req->data_buf, img, num_bytes);
img += num_bytes;
status = be_cmd_write_flashrom(adapter, flash_cmd, optype,
- flash_op, num_bytes);
+ flash_op, img_offset +
+ bytes_sent, num_bytes);
if (base_status(status) == MCC_STATUS_ILLEGAL_REQUEST &&
optype == OPTYPE_PHY_FW)
break;
else if (status)
return status;
+
+ bytes_sent += num_bytes;
}
return 0;
}
@@ -4103,7 +4107,7 @@ static int be_flash_BEx(struct be_adapter *adapter,
return -1;
status = be_flash(adapter, p, flash_cmd, pflashcomp[i].optype,
- pflashcomp[i].size);
+ pflashcomp[i].size, 0);
if (status) {
dev_err(dev, "Flashing section type 0x%x failed\n",
pflashcomp[i].img_type);
@@ -4170,12 +4174,12 @@ static int be_flash_skyhawk(struct be_adapter *adapter,
struct be_dma_mem *flash_cmd, int num_of_images)
{
int img_hdrs_size = num_of_images * sizeof(struct image_hdr);
+ bool crc_match, old_fw_img, flash_offset_support = true;
struct device *dev = &adapter->pdev->dev;
struct flash_section_info *fsec = NULL;
u32 img_offset, img_size, img_type;
+ u16 img_optype, flash_optype;
int status, i, filehdr_size;
- bool crc_match, old_fw_img;
- u16 img_optype;
const u8 *p;
filehdr_size = sizeof(struct flash_file_hdr_g3);
@@ -4185,6 +4189,7 @@ static int be_flash_skyhawk(struct be_adapter *adapter,
return -EINVAL;
}
+retry_flash:
for (i = 0; i < le32_to_cpu(fsec->fsec_hdr.num_images); i++) {
img_offset = le32_to_cpu(fsec->fsec_entry[i].offset);
img_size = le32_to_cpu(fsec->fsec_entry[i].pad_size);
@@ -4194,6 +4199,12 @@ static int be_flash_skyhawk(struct be_adapter *adapter,
if (img_optype == 0xFFFF)
continue;
+
+ if (flash_offset_support)
+ flash_optype = OPTYPE_OFFSET_SPECIFIED;
+ else
+ flash_optype = img_optype;
+
/* Don't bother verifying CRC if an old FW image is being
* flashed
*/
@@ -4202,16 +4213,26 @@ static int be_flash_skyhawk(struct be_adapter *adapter,
status = be_check_flash_crc(adapter, fw->data, img_offset,
img_size, filehdr_size +
- img_hdrs_size, img_optype,
+ img_hdrs_size, flash_optype,
&crc_match);
- /* The current FW image on the card does not recognize the new
- * FLASH op_type. The FW download is partially complete.
- * Reboot the server now to enable FW image to recognize the
- * new FLASH op_type. To complete the remaining process,
- * download the same FW again after the reboot.
- */
if (base_status(status) == MCC_STATUS_ILLEGAL_REQUEST ||
base_status(status) == MCC_STATUS_ILLEGAL_FIELD) {
+ /* The current FW image on the card does not support
+ * OFFSET based flashing. Retry using older mechanism
+ * of OPTYPE based flashing
+ */
+ if (flash_optype == OPTYPE_OFFSET_SPECIFIED) {
+ flash_offset_support = false;
+ goto retry_flash;
+ }
+
+ /* The current FW image on the card does not recognize
+ * the new FLASH op_type. The FW download is partially
+ * complete. Reboot the server now to enable FW image
+ * to recognize the new FLASH op_type. To complete the
+ * remaining process, download the same FW again after
+ * the reboot.
+ */
dev_err(dev, "Flash incomplete. Reset the server\n");
dev_err(dev, "Download FW image again after reset\n");
return -EAGAIN;
@@ -4229,7 +4250,19 @@ flash:
if (p + img_size > fw->data + fw->size)
return -1;
- status = be_flash(adapter, p, flash_cmd, img_optype, img_size);
+ status = be_flash(adapter, p, flash_cmd, flash_optype, img_size,
+ img_offset);
+
+ /* The current FW image on the card does not support OFFSET
+ * based flashing. Retry using older mechanism of OPTYPE based
+ * flashing
+ */
+ if (base_status(status) == MCC_STATUS_ILLEGAL_FIELD &&
+ flash_optype == OPTYPE_OFFSET_SPECIFIED) {
+ flash_offset_support = false;
+ goto retry_flash;
+ }
+
/* For old FW images ignore ILLEGAL_FIELD error or errors on
* UFI_DIR region
*/
--
2.2.0
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH net-next 6/9] be2net: remove duplicate code in be_cmd_rx_filter()
2015-02-06 13:18 [PATCH net-next 0/9] be2net: patch set Sathya Perla
` (4 preceding siblings ...)
2015-02-06 13:18 ` [PATCH net-next 5/9] be2net: use offset based FW flashing for Skyhawk chip Sathya Perla
@ 2015-02-06 13:18 ` Sathya Perla
2015-02-06 13:18 ` [PATCH net-next 7/9] be2net: refactor be_set_rx_mode() and be_vid_config() for readability Sathya Perla
` (3 subsequent siblings)
9 siblings, 0 replies; 14+ messages in thread
From: Sathya Perla @ 2015-02-06 13:18 UTC (permalink / raw)
To: netdev
This patch passes BE_IF_FLAGS_XXX flags to be_cmd_rx_filter() routine
instead of the IFF_XXX flags. Doing this gets rid of the code to convert
the IFF_XXX flags to the BE_IF_FLAGS_XXX used by the FW cmd. The patch
also removes code for setting if_flags_mask that was duplicated for each
filter mode.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
---
drivers/net/ethernet/emulex/benet/be_cmds.c | 54 ++++++++++-------------------
drivers/net/ethernet/emulex/benet/be_cmds.h | 4 +++
drivers/net/ethernet/emulex/benet/be_main.c | 29 +++++++---------
3 files changed, 36 insertions(+), 51 deletions(-)
diff --git a/drivers/net/ethernet/emulex/benet/be_cmds.c b/drivers/net/ethernet/emulex/benet/be_cmds.c
index 2f59553..1c85bbf 100644
--- a/drivers/net/ethernet/emulex/benet/be_cmds.c
+++ b/drivers/net/ethernet/emulex/benet/be_cmds.c
@@ -1886,7 +1886,7 @@ err:
return status;
}
-int be_cmd_rx_filter(struct be_adapter *adapter, u32 flags, u32 value)
+static int __be_cmd_rx_filter(struct be_adapter *adapter, u32 flags, u32 value)
{
struct be_mcc_wrb *wrb;
struct be_dma_mem *mem = &adapter->rx_filter;
@@ -1906,31 +1906,13 @@ int be_cmd_rx_filter(struct be_adapter *adapter, u32 flags, u32 value)
wrb, mem);
req->if_id = cpu_to_le32(adapter->if_handle);
- if (flags & IFF_PROMISC) {
- req->if_flags_mask = cpu_to_le32(BE_IF_FLAGS_PROMISCUOUS |
- BE_IF_FLAGS_VLAN_PROMISCUOUS |
- BE_IF_FLAGS_MCAST_PROMISCUOUS);
- if (value == ON)
- req->if_flags =
- cpu_to_le32(BE_IF_FLAGS_PROMISCUOUS |
- BE_IF_FLAGS_VLAN_PROMISCUOUS |
- BE_IF_FLAGS_MCAST_PROMISCUOUS);
- } else if (flags & IFF_ALLMULTI) {
- req->if_flags_mask = cpu_to_le32(BE_IF_FLAGS_MCAST_PROMISCUOUS);
- req->if_flags = cpu_to_le32(BE_IF_FLAGS_MCAST_PROMISCUOUS);
- } else if (flags & BE_FLAGS_VLAN_PROMISC) {
- req->if_flags_mask = cpu_to_le32(BE_IF_FLAGS_VLAN_PROMISCUOUS);
-
- if (value == ON)
- req->if_flags =
- cpu_to_le32(BE_IF_FLAGS_VLAN_PROMISCUOUS);
- } else {
+ req->if_flags_mask = cpu_to_le32(flags);
+ req->if_flags = (value == ON) ? req->if_flags_mask : 0;
+
+ if (flags & BE_IF_FLAGS_MULTICAST) {
struct netdev_hw_addr *ha;
int i = 0;
- req->if_flags_mask = cpu_to_le32(BE_IF_FLAGS_MULTICAST);
- req->if_flags = cpu_to_le32(BE_IF_FLAGS_MULTICAST);
-
/* Reset mcast promisc mode if already set by setting mask
* and not setting flags field
*/
@@ -1942,24 +1924,26 @@ int be_cmd_rx_filter(struct be_adapter *adapter, u32 flags, u32 value)
memcpy(req->mcast_mac[i++].byte, ha->addr, ETH_ALEN);
}
- if ((req->if_flags_mask & cpu_to_le32(be_if_cap_flags(adapter))) !=
- req->if_flags_mask) {
- dev_warn(&adapter->pdev->dev,
- "Cannot set rx filter flags 0x%x\n",
- req->if_flags_mask);
- dev_warn(&adapter->pdev->dev,
- "Interface is capable of 0x%x flags only\n",
- be_if_cap_flags(adapter));
- }
- req->if_flags_mask &= cpu_to_le32(be_if_cap_flags(adapter));
-
status = be_mcc_notify_wait(adapter);
-
err:
spin_unlock_bh(&adapter->mcc_lock);
return status;
}
+int be_cmd_rx_filter(struct be_adapter *adapter, u32 flags, u32 value)
+{
+ struct device *dev = &adapter->pdev->dev;
+
+ if ((flags & be_if_cap_flags(adapter)) != flags) {
+ dev_warn(dev, "Cannot set rx filter flags 0x%x\n", flags);
+ dev_warn(dev, "Interface is capable of 0x%x flags only\n",
+ be_if_cap_flags(adapter));
+ }
+ flags &= be_if_cap_flags(adapter);
+
+ return __be_cmd_rx_filter(adapter, flags, value);
+}
+
/* Uses synchrounous mcc */
int be_cmd_set_flow_control(struct be_adapter *adapter, u32 tx_fc, u32 rx_fc)
{
diff --git a/drivers/net/ethernet/emulex/benet/be_cmds.h b/drivers/net/ethernet/emulex/benet/be_cmds.h
index 402d64f..cf9d870 100644
--- a/drivers/net/ethernet/emulex/benet/be_cmds.h
+++ b/drivers/net/ethernet/emulex/benet/be_cmds.h
@@ -586,6 +586,10 @@ enum be_if_flags {
BE_IF_FLAGS_PASS_L3L4_ERRORS | BE_IF_FLAGS_MULTICAST |\
BE_IF_FLAGS_UNTAGGED)
+#define BE_IF_FLAGS_ALL_PROMISCUOUS (BE_IF_FLAGS_PROMISCUOUS | \
+ BE_IF_FLAGS_VLAN_PROMISCUOUS |\
+ BE_IF_FLAGS_MCAST_PROMISCUOUS)
+
/* An RX interface is an object with one or more MAC addresses and
* filtering capabilities. */
struct be_cmd_req_if_create {
diff --git a/drivers/net/ethernet/emulex/benet/be_main.c b/drivers/net/ethernet/emulex/benet/be_main.c
index 2ec1d80..4f7a14b 100644
--- a/drivers/net/ethernet/emulex/benet/be_main.c
+++ b/drivers/net/ethernet/emulex/benet/be_main.c
@@ -1133,16 +1133,12 @@ static int be_vid_config(struct be_adapter *adapter)
MCC_ADDL_STATUS_INSUFFICIENT_RESOURCES)
goto set_vlan_promisc;
dev_err(dev, "Setting HW VLAN filtering failed\n");
- } else {
- if (adapter->flags & BE_FLAGS_VLAN_PROMISC) {
- /* hw VLAN filtering re-enabled. */
- status = be_cmd_rx_filter(adapter,
- BE_FLAGS_VLAN_PROMISC, OFF);
- if (!status) {
- dev_info(dev,
- "Disabling VLAN Promiscuous mode\n");
- adapter->flags &= ~BE_FLAGS_VLAN_PROMISC;
- }
+ } else if (adapter->flags & BE_FLAGS_VLAN_PROMISC) {
+ status = be_cmd_rx_filter(adapter, BE_IF_FLAGS_VLAN_PROMISCUOUS,
+ OFF);
+ if (!status) {
+ dev_info(dev, "Disabling VLAN Promiscuous mode\n");
+ adapter->flags &= ~BE_FLAGS_VLAN_PROMISC;
}
}
@@ -1152,7 +1148,7 @@ set_vlan_promisc:
if (adapter->flags & BE_FLAGS_VLAN_PROMISC)
return 0;
- status = be_cmd_rx_filter(adapter, BE_FLAGS_VLAN_PROMISC, ON);
+ status = be_cmd_rx_filter(adapter, BE_IF_FLAGS_VLAN_PROMISCUOUS, ON);
if (!status) {
dev_info(dev, "Enable VLAN Promiscuous mode\n");
adapter->flags |= BE_FLAGS_VLAN_PROMISC;
@@ -1204,7 +1200,7 @@ static void be_clear_promisc(struct be_adapter *adapter)
adapter->promiscuous = false;
adapter->flags &= ~(BE_FLAGS_VLAN_PROMISC | BE_FLAGS_MCAST_PROMISC);
- be_cmd_rx_filter(adapter, IFF_PROMISC, OFF);
+ be_cmd_rx_filter(adapter, BE_IF_FLAGS_ALL_PROMISCUOUS, OFF);
}
static void be_set_rx_mode(struct net_device *netdev)
@@ -1213,7 +1209,7 @@ static void be_set_rx_mode(struct net_device *netdev)
int status;
if (netdev->flags & IFF_PROMISC) {
- be_cmd_rx_filter(adapter, IFF_PROMISC, ON);
+ be_cmd_rx_filter(adapter, BE_IF_FLAGS_ALL_PROMISCUOUS, ON);
adapter->promiscuous = true;
goto done;
}
@@ -1240,7 +1236,8 @@ static void be_set_rx_mode(struct net_device *netdev)
}
if (netdev_uc_count(netdev) > be_max_uc(adapter)) {
- be_cmd_rx_filter(adapter, IFF_PROMISC, ON);
+ be_cmd_rx_filter(adapter, BE_IF_FLAGS_ALL_PROMISCUOUS,
+ ON);
adapter->promiscuous = true;
goto done;
}
@@ -1253,7 +1250,7 @@ static void be_set_rx_mode(struct net_device *netdev)
}
}
- status = be_cmd_rx_filter(adapter, IFF_MULTICAST, ON);
+ status = be_cmd_rx_filter(adapter, BE_IF_FLAGS_MULTICAST, ON);
if (!status) {
if (adapter->flags & BE_FLAGS_MCAST_PROMISC)
adapter->flags &= ~BE_FLAGS_MCAST_PROMISC;
@@ -1267,7 +1264,7 @@ set_mcast_promisc:
/* Set to MCAST promisc mode if setting MULTICAST address fails
* or if num configured exceeds what we support
*/
- status = be_cmd_rx_filter(adapter, IFF_ALLMULTI, ON);
+ status = be_cmd_rx_filter(adapter, BE_IF_FLAGS_MCAST_PROMISCUOUS, ON);
if (!status)
adapter->flags |= BE_FLAGS_MCAST_PROMISC;
done:
--
2.2.0
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH net-next 7/9] be2net: refactor be_set_rx_mode() and be_vid_config() for readability
2015-02-06 13:18 [PATCH net-next 0/9] be2net: patch set Sathya Perla
` (5 preceding siblings ...)
2015-02-06 13:18 ` [PATCH net-next 6/9] be2net: remove duplicate code in be_cmd_rx_filter() Sathya Perla
@ 2015-02-06 13:18 ` Sathya Perla
2015-02-06 13:18 ` [PATCH net-next 8/9] be2net: process port misconfig async event Sathya Perla
` (2 subsequent siblings)
9 siblings, 0 replies; 14+ messages in thread
From: Sathya Perla @ 2015-02-06 13:18 UTC (permalink / raw)
To: netdev
This patch re-factors the filter setting (uc-list, mc-list, promisc, vlan)
code in be_set_rx_mode() and be_vid_config() to make it more readable
and reduce code duplication.
This patch adds a separate field to track the state/mode of filtering,
along with moving all the filtering related fields to one place in be
be_adapter structure.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
---
drivers/net/ethernet/emulex/benet/be.h | 13 +-
drivers/net/ethernet/emulex/benet/be_main.c | 211 ++++++++++++++++------------
2 files changed, 127 insertions(+), 97 deletions(-)
diff --git a/drivers/net/ethernet/emulex/benet/be.h b/drivers/net/ethernet/emulex/benet/be.h
index 9869556..98716e1 100644
--- a/drivers/net/ethernet/emulex/benet/be.h
+++ b/drivers/net/ethernet/emulex/benet/be.h
@@ -364,8 +364,6 @@ enum vf_state {
#define BE_FLAGS_LINK_STATUS_INIT BIT(1)
#define BE_FLAGS_SRIOV_ENABLED BIT(2)
#define BE_FLAGS_WORKER_SCHEDULED BIT(3)
-#define BE_FLAGS_VLAN_PROMISC BIT(4)
-#define BE_FLAGS_MCAST_PROMISC BIT(5)
#define BE_FLAGS_NAPI_ENABLED BIT(6)
#define BE_FLAGS_QNQ_ASYNC_EVT_RCVD BIT(7)
#define BE_FLAGS_VXLAN_OFFLOADS BIT(8)
@@ -449,8 +447,6 @@ struct be_adapter {
struct be_drv_stats drv_stats;
struct be_aic_obj aic_obj[MAX_EVT_QS];
- u16 vlans_added;
- unsigned long vids[BITS_TO_LONGS(VLAN_N_VID)];
u8 vlan_prio_bmap; /* Available Priority BitMap */
u16 recommended_prio; /* Recommended Priority */
struct be_dma_mem rx_filter; /* Cmd DMA mem for rx-filter */
@@ -466,8 +462,15 @@ struct be_adapter {
/* Ethtool knobs and info */
char fw_ver[FW_VER_LEN];
char fw_on_flash[FW_VER_LEN];
+
+ /* IFACE filtering fields */
int if_handle; /* Used to configure filtering */
+ u32 if_flags; /* Interface filtering flags */
u32 *pmac_id; /* MAC addr handle used by BE card */
+ u32 uc_macs; /* Count of secondary UC MAC programmed */
+ unsigned long vids[BITS_TO_LONGS(VLAN_N_VID)];
+ u16 vlans_added;
+
u32 beacon_state; /* for set_phys_id */
bool eeh_error;
@@ -475,7 +478,6 @@ struct be_adapter {
bool hw_error;
u32 port_num;
- bool promiscuous;
u8 mc_type;
u32 function_mode;
u32 function_caps;
@@ -508,7 +510,6 @@ struct be_adapter {
struct phy_info phy;
u8 wol_cap;
bool wol_en;
- u32 uc_macs; /* Count of secondary UC MAC programmed */
u16 asic_rev;
u16 qnq_vid;
u32 msg_enable;
diff --git a/drivers/net/ethernet/emulex/benet/be_main.c b/drivers/net/ethernet/emulex/benet/be_main.c
index 4f7a14b..fbe7b6f 100644
--- a/drivers/net/ethernet/emulex/benet/be_main.c
+++ b/drivers/net/ethernet/emulex/benet/be_main.c
@@ -1104,6 +1104,43 @@ static int be_change_mtu(struct net_device *netdev, int new_mtu)
return 0;
}
+static inline bool be_in_all_promisc(struct be_adapter *adapter)
+{
+ return (adapter->if_flags & BE_IF_FLAGS_ALL_PROMISCUOUS) ==
+ BE_IF_FLAGS_ALL_PROMISCUOUS;
+}
+
+static int be_set_vlan_promisc(struct be_adapter *adapter)
+{
+ struct device *dev = &adapter->pdev->dev;
+ int status;
+
+ if (adapter->if_flags & BE_IF_FLAGS_VLAN_PROMISCUOUS)
+ return 0;
+
+ status = be_cmd_rx_filter(adapter, BE_IF_FLAGS_VLAN_PROMISCUOUS, ON);
+ if (!status) {
+ dev_info(dev, "Enabled VLAN promiscuous mode\n");
+ adapter->if_flags |= BE_IF_FLAGS_VLAN_PROMISCUOUS;
+ } else {
+ dev_err(dev, "Failed to enable VLAN promiscuous mode\n");
+ }
+ return status;
+}
+
+static int be_clear_vlan_promisc(struct be_adapter *adapter)
+{
+ struct device *dev = &adapter->pdev->dev;
+ int status;
+
+ status = be_cmd_rx_filter(adapter, BE_IF_FLAGS_VLAN_PROMISCUOUS, OFF);
+ if (!status) {
+ dev_info(dev, "Disabling VLAN promiscuous mode\n");
+ adapter->if_flags &= ~BE_IF_FLAGS_VLAN_PROMISCUOUS;
+ }
+ return status;
+}
+
/*
* A max of 64 (BE_NUM_VLANS_SUPPORTED) vlans can be configured in BE.
* If the user configures more, place BE in vlan promiscuous mode.
@@ -1116,11 +1153,11 @@ static int be_vid_config(struct be_adapter *adapter)
int status = 0;
/* No need to further configure vids if in promiscuous mode */
- if (adapter->promiscuous)
+ if (be_in_all_promisc(adapter))
return 0;
if (adapter->vlans_added > be_max_vlans(adapter))
- goto set_vlan_promisc;
+ return be_set_vlan_promisc(adapter);
/* Construct VLAN Table to give to HW */
for_each_set_bit(i, adapter->vids, VLAN_N_VID)
@@ -1128,32 +1165,14 @@ static int be_vid_config(struct be_adapter *adapter)
status = be_cmd_vlan_config(adapter, adapter->if_handle, vids, num);
if (status) {
+ dev_err(dev, "Setting HW VLAN filtering failed\n");
/* Set to VLAN promisc mode as setting VLAN filter failed */
if (addl_status(status) ==
MCC_ADDL_STATUS_INSUFFICIENT_RESOURCES)
- goto set_vlan_promisc;
- dev_err(dev, "Setting HW VLAN filtering failed\n");
- } else if (adapter->flags & BE_FLAGS_VLAN_PROMISC) {
- status = be_cmd_rx_filter(adapter, BE_IF_FLAGS_VLAN_PROMISCUOUS,
- OFF);
- if (!status) {
- dev_info(dev, "Disabling VLAN Promiscuous mode\n");
- adapter->flags &= ~BE_FLAGS_VLAN_PROMISC;
- }
+ return be_set_vlan_promisc(adapter);
+ } else if (adapter->if_flags & BE_IF_FLAGS_VLAN_PROMISCUOUS) {
+ status = be_clear_vlan_promisc(adapter);
}
-
- return status;
-
-set_vlan_promisc:
- if (adapter->flags & BE_FLAGS_VLAN_PROMISC)
- return 0;
-
- status = be_cmd_rx_filter(adapter, BE_IF_FLAGS_VLAN_PROMISCUOUS, ON);
- if (!status) {
- dev_info(dev, "Enable VLAN Promiscuous mode\n");
- adapter->flags |= BE_FLAGS_VLAN_PROMISC;
- } else
- dev_err(dev, "Failed to enable VLAN Promiscuous mode\n");
return status;
}
@@ -1195,80 +1214,99 @@ static int be_vlan_rem_vid(struct net_device *netdev, __be16 proto, u16 vid)
return be_vid_config(adapter);
}
-static void be_clear_promisc(struct be_adapter *adapter)
+static void be_clear_all_promisc(struct be_adapter *adapter)
{
- adapter->promiscuous = false;
- adapter->flags &= ~(BE_FLAGS_VLAN_PROMISC | BE_FLAGS_MCAST_PROMISC);
-
be_cmd_rx_filter(adapter, BE_IF_FLAGS_ALL_PROMISCUOUS, OFF);
+ adapter->if_flags &= ~BE_IF_FLAGS_ALL_PROMISCUOUS;
}
-static void be_set_rx_mode(struct net_device *netdev)
+static void be_set_all_promisc(struct be_adapter *adapter)
+{
+ be_cmd_rx_filter(adapter, BE_IF_FLAGS_ALL_PROMISCUOUS, ON);
+ adapter->if_flags |= BE_IF_FLAGS_ALL_PROMISCUOUS;
+}
+
+static void be_set_mc_promisc(struct be_adapter *adapter)
{
- struct be_adapter *adapter = netdev_priv(netdev);
int status;
- if (netdev->flags & IFF_PROMISC) {
- be_cmd_rx_filter(adapter, BE_IF_FLAGS_ALL_PROMISCUOUS, ON);
- adapter->promiscuous = true;
- goto done;
- }
+ if (adapter->if_flags & BE_IF_FLAGS_MCAST_PROMISCUOUS)
+ return;
- /* BE was previously in promiscuous mode; disable it */
- if (adapter->promiscuous) {
- be_clear_promisc(adapter);
- if (adapter->vlans_added)
- be_vid_config(adapter);
+ status = be_cmd_rx_filter(adapter, BE_IF_FLAGS_MCAST_PROMISCUOUS, ON);
+ if (!status)
+ adapter->if_flags |= BE_IF_FLAGS_MCAST_PROMISCUOUS;
+}
+
+static void be_set_mc_list(struct be_adapter *adapter)
+{
+ int status;
+
+ status = be_cmd_rx_filter(adapter, BE_IF_FLAGS_MULTICAST, ON);
+ if (!status)
+ adapter->if_flags &= ~BE_IF_FLAGS_MCAST_PROMISCUOUS;
+ else
+ be_set_mc_promisc(adapter);
+}
+
+static void be_set_uc_list(struct be_adapter *adapter)
+{
+ struct netdev_hw_addr *ha;
+ int i = 1; /* First slot is claimed by the Primary MAC */
+
+ for (; adapter->uc_macs > 0; adapter->uc_macs--, i++)
+ be_cmd_pmac_del(adapter, adapter->if_handle,
+ adapter->pmac_id[i], 0);
+
+ if (netdev_uc_count(adapter->netdev) > be_max_uc(adapter)) {
+ be_set_all_promisc(adapter);
+ return;
}
- /* Enable multicast promisc if num configured exceeds what we support */
- if (netdev->flags & IFF_ALLMULTI ||
- netdev_mc_count(netdev) > be_max_mc(adapter))
- goto set_mcast_promisc;
+ netdev_for_each_uc_addr(ha, adapter->netdev) {
+ adapter->uc_macs++; /* First slot is for Primary MAC */
+ be_cmd_pmac_add(adapter, (u8 *)ha->addr, adapter->if_handle,
+ &adapter->pmac_id[adapter->uc_macs], 0);
+ }
+}
- if (netdev_uc_count(netdev) != adapter->uc_macs) {
- struct netdev_hw_addr *ha;
- int i = 1; /* First slot is claimed by the Primary MAC */
+static void be_clear_uc_list(struct be_adapter *adapter)
+{
+ int i;
- for (; adapter->uc_macs > 0; adapter->uc_macs--, i++) {
- be_cmd_pmac_del(adapter, adapter->if_handle,
- adapter->pmac_id[i], 0);
- }
+ for (i = 1; i < (adapter->uc_macs + 1); i++)
+ be_cmd_pmac_del(adapter, adapter->if_handle,
+ adapter->pmac_id[i], 0);
+ adapter->uc_macs = 0;
+}
- if (netdev_uc_count(netdev) > be_max_uc(adapter)) {
- be_cmd_rx_filter(adapter, BE_IF_FLAGS_ALL_PROMISCUOUS,
- ON);
- adapter->promiscuous = true;
- goto done;
- }
+static void be_set_rx_mode(struct net_device *netdev)
+{
+ struct be_adapter *adapter = netdev_priv(netdev);
- netdev_for_each_uc_addr(ha, adapter->netdev) {
- adapter->uc_macs++; /* First slot is for Primary MAC */
- be_cmd_pmac_add(adapter, (u8 *)ha->addr,
- adapter->if_handle,
- &adapter->pmac_id[adapter->uc_macs], 0);
- }
+ if (netdev->flags & IFF_PROMISC) {
+ be_set_all_promisc(adapter);
+ return;
}
- status = be_cmd_rx_filter(adapter, BE_IF_FLAGS_MULTICAST, ON);
- if (!status) {
- if (adapter->flags & BE_FLAGS_MCAST_PROMISC)
- adapter->flags &= ~BE_FLAGS_MCAST_PROMISC;
- goto done;
+ /* Interface was previously in promiscuous mode; disable it */
+ if (be_in_all_promisc(adapter)) {
+ be_clear_all_promisc(adapter);
+ if (adapter->vlans_added)
+ be_vid_config(adapter);
}
-set_mcast_promisc:
- if (adapter->flags & BE_FLAGS_MCAST_PROMISC)
+ /* Enable multicast promisc if num configured exceeds what we support */
+ if (netdev->flags & IFF_ALLMULTI ||
+ netdev_mc_count(netdev) > be_max_mc(adapter)) {
+ be_set_mc_promisc(adapter);
return;
+ }
- /* Set to MCAST promisc mode if setting MULTICAST address fails
- * or if num configured exceeds what we support
- */
- status = be_cmd_rx_filter(adapter, BE_IF_FLAGS_MCAST_PROMISCUOUS, ON);
- if (!status)
- adapter->flags |= BE_FLAGS_MCAST_PROMISC;
-done:
- return;
+ if (netdev_uc_count(netdev) != adapter->uc_macs)
+ be_set_uc_list(adapter);
+
+ be_set_mc_list(adapter);
}
static int be_set_vf_mac(struct net_device *netdev, int vf, u8 *mac)
@@ -2947,11 +2985,7 @@ static int be_close(struct net_device *netdev)
be_tx_compl_clean(adapter);
be_rx_qs_destroy(adapter);
-
- for (i = 1; i < (adapter->uc_macs + 1); i++)
- be_cmd_pmac_del(adapter, adapter->if_handle,
- adapter->pmac_id[i], 0);
- adapter->uc_macs = 0;
+ be_clear_uc_list(adapter);
for_all_evt_queues(adapter, eqo, i) {
if (msix_enabled(adapter))
@@ -3235,14 +3269,9 @@ static void be_cancel_worker(struct be_adapter *adapter)
static void be_mac_clear(struct be_adapter *adapter)
{
- int i;
-
if (adapter->pmac_id) {
- for (i = 0; i < (adapter->uc_macs + 1); i++)
- be_cmd_pmac_del(adapter, adapter->if_handle,
- adapter->pmac_id[i], 0);
- adapter->uc_macs = 0;
-
+ be_cmd_pmac_del(adapter, adapter->if_handle,
+ adapter->pmac_id[0], 0);
kfree(adapter->pmac_id);
adapter->pmac_id = NULL;
}
@@ -3526,7 +3555,7 @@ static void be_setup_init(struct be_adapter *adapter)
adapter->phy.link_speed = -1;
adapter->if_handle = -1;
adapter->be3_native = false;
- adapter->promiscuous = false;
+ adapter->if_flags = 0;
if (be_physfn(adapter))
adapter->cmd_privileges = MAX_PRIVILEGES;
else
--
2.2.0
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH net-next 8/9] be2net: process port misconfig async event
2015-02-06 13:18 [PATCH net-next 0/9] be2net: patch set Sathya Perla
` (6 preceding siblings ...)
2015-02-06 13:18 ` [PATCH net-next 7/9] be2net: refactor be_set_rx_mode() and be_vid_config() for readability Sathya Perla
@ 2015-02-06 13:18 ` Sathya Perla
2015-02-06 13:18 ` [PATCH net-next 9/9] be2net: avoid unncessary swapping of fields in eth_tx_wrb Sathya Perla
2015-02-08 6:52 ` [PATCH net-next 0/9] be2net: patch set David Miller
9 siblings, 0 replies; 14+ messages in thread
From: Sathya Perla @ 2015-02-06 13:18 UTC (permalink / raw)
To: netdev
From: Vasundhara Volam <vasundhara.volam@emulex.com>
This patch adds support for processing the port misconfigure async
event generated by the FW. This event is generated typically when an
optical module is incorrectly installed or is faulty.
This patch also moves the port_name field to the adapter struct for
logging the event. As the be_cmd_query_port_name() call is now moved
to be_get_config(), it is modified to use the mailbox instead of MCCQ
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
---
drivers/net/ethernet/emulex/benet/be.h | 6 ++
drivers/net/ethernet/emulex/benet/be_cmds.c | 119 ++++++++++++++++++++++------
drivers/net/ethernet/emulex/benet/be_cmds.h | 16 +++-
drivers/net/ethernet/emulex/benet/be_main.c | 28 +++++--
4 files changed, 139 insertions(+), 30 deletions(-)
diff --git a/drivers/net/ethernet/emulex/benet/be.h b/drivers/net/ethernet/emulex/benet/be.h
index 98716e1..27de37a 100644
--- a/drivers/net/ethernet/emulex/benet/be.h
+++ b/drivers/net/ethernet/emulex/benet/be.h
@@ -368,6 +368,7 @@ enum vf_state {
#define BE_FLAGS_QNQ_ASYNC_EVT_RCVD BIT(7)
#define BE_FLAGS_VXLAN_OFFLOADS BIT(8)
#define BE_FLAGS_SETUP_DONE BIT(9)
+#define BE_FLAGS_EVT_INCOMPATIBLE_SFP BIT(10)
#define BE_UC_PMAC_COUNT 30
#define BE_VF_UC_PMAC_COUNT 2
@@ -377,6 +378,8 @@ enum vf_state {
#define LANCER_DELETE_FW_DUMP 0x2
struct phy_info {
+/* From SFF-8472 spec */
+#define SFP_VENDOR_NAME_LEN 17
u8 transceiver;
u8 autoneg;
u8 fc_autoneg;
@@ -390,6 +393,8 @@ struct phy_info {
u32 advertising;
u32 supported;
u8 cable_type;
+ u8 vendor_name[SFP_VENDOR_NAME_LEN];
+ u8 vendor_pn[SFP_VENDOR_NAME_LEN];
};
struct be_resources {
@@ -478,6 +483,7 @@ struct be_adapter {
bool hw_error;
u32 port_num;
+ char port_name;
u8 mc_type;
u32 function_mode;
u32 function_caps;
diff --git a/drivers/net/ethernet/emulex/benet/be_cmds.c b/drivers/net/ethernet/emulex/benet/be_cmds.c
index 1c85bbf..f0276f5 100644
--- a/drivers/net/ethernet/emulex/benet/be_cmds.c
+++ b/drivers/net/ethernet/emulex/benet/be_cmds.c
@@ -19,6 +19,22 @@
#include "be.h"
#include "be_cmds.h"
+static char *be_port_misconfig_evt_desc[] = {
+ "A valid SFP module detected",
+ "Optics faulted/ incorrectly installed/ not installed.",
+ "Optics of two types installed.",
+ "Incompatible optics.",
+ "Unknown port SFP status"
+};
+
+static char *be_port_misconfig_remedy_desc[] = {
+ "",
+ "Reseat optics. If issue not resolved, replace",
+ "Remove one optic or install matching pair of optics",
+ "Replace with compatible optics for card to function",
+ ""
+};
+
static struct be_cmd_priv_map cmd_priv_map[] = {
{
OPCODE_ETH_ACPI_WOL_MAGIC_CONFIG,
@@ -249,6 +265,29 @@ static void be_async_link_state_process(struct be_adapter *adapter,
evt->port_link_status & LINK_STATUS_MASK);
}
+static void be_async_port_misconfig_event_process(struct be_adapter *adapter,
+ struct be_mcc_compl *compl)
+{
+ struct be_async_event_misconfig_port *evt =
+ (struct be_async_event_misconfig_port *)compl;
+ u32 sfp_mismatch_evt = le32_to_cpu(evt->event_data_word1);
+ struct device *dev = &adapter->pdev->dev;
+ u8 port_misconfig_evt;
+
+ port_misconfig_evt =
+ ((sfp_mismatch_evt >> (adapter->hba_port_num * 8)) & 0xff);
+
+ /* Log an error message that would allow a user to determine
+ * whether the SFPs have an issue
+ */
+ dev_info(dev, "Port %c: %s %s", adapter->port_name,
+ be_port_misconfig_evt_desc[port_misconfig_evt],
+ be_port_misconfig_remedy_desc[port_misconfig_evt]);
+
+ if (port_misconfig_evt == INCOMPATIBLE_SFP)
+ adapter->flags |= BE_FLAGS_EVT_INCOMPATIBLE_SFP;
+}
+
/* Grp5 CoS Priority evt */
static void be_async_grp5_cos_priority_process(struct be_adapter *adapter,
struct be_mcc_compl *compl)
@@ -334,6 +373,16 @@ static void be_async_dbg_evt_process(struct be_adapter *adapter,
}
}
+static void be_async_sliport_evt_process(struct be_adapter *adapter,
+ struct be_mcc_compl *cmp)
+{
+ u8 event_type = (cmp->flags >> ASYNC_EVENT_TYPE_SHIFT) &
+ ASYNC_EVENT_TYPE_MASK;
+
+ if (event_type == ASYNC_EVENT_PORT_MISCONFIG)
+ be_async_port_misconfig_event_process(adapter, cmp);
+}
+
static inline bool is_link_state_evt(u32 flags)
{
return ((flags >> ASYNC_EVENT_CODE_SHIFT) & ASYNC_EVENT_CODE_MASK) ==
@@ -352,6 +401,12 @@ static inline bool is_dbg_evt(u32 flags)
ASYNC_EVENT_CODE_QNQ;
}
+static inline bool is_sliport_evt(u32 flags)
+{
+ return ((flags >> ASYNC_EVENT_CODE_SHIFT) & ASYNC_EVENT_CODE_MASK) ==
+ ASYNC_EVENT_CODE_SLIPORT;
+}
+
static void be_mcc_event_process(struct be_adapter *adapter,
struct be_mcc_compl *compl)
{
@@ -361,6 +416,8 @@ static void be_mcc_event_process(struct be_adapter *adapter,
be_async_grp5_evt_process(adapter, compl);
else if (is_dbg_evt(compl->flags))
be_async_dbg_evt_process(adapter, compl);
+ else if (is_sliport_evt(compl->flags))
+ be_async_sliport_evt_process(adapter, compl);
}
static struct be_mcc_compl *be_mcc_compl_get(struct be_adapter *adapter)
@@ -1171,9 +1228,15 @@ static int be_cmd_mccq_ext_create(struct be_adapter *adapter,
ctxt, 1);
}
- /* Subscribe to Link State and Group 5 Events(bits 1 and 5 set) */
- req->async_event_bitmap[0] = cpu_to_le32(0x00000022);
- req->async_event_bitmap[0] |= cpu_to_le32(1 << ASYNC_EVENT_CODE_QNQ);
+ /* Subscribe to Link State, Sliport Event and Group 5 Events
+ * (bits 1, 5 and 17 set)
+ */
+ req->async_event_bitmap[0] =
+ cpu_to_le32(BIT(ASYNC_EVENT_CODE_LINK_STATE) |
+ BIT(ASYNC_EVENT_CODE_GRP_5) |
+ BIT(ASYNC_EVENT_CODE_QNQ) |
+ BIT(ASYNC_EVENT_CODE_SLIPORT));
+
be_dws_cpu_to_le(ctxt, sizeof(req->context));
be_cmd_page_addrs_prepare(req->pages, ARRAY_SIZE(req->pages), q_mem);
@@ -2344,6 +2407,24 @@ int be_cmd_query_cable_type(struct be_adapter *adapter)
return status;
}
+int be_cmd_query_sfp_info(struct be_adapter *adapter)
+{
+ u8 page_data[PAGE_DATA_LEN];
+ int status;
+
+ status = be_cmd_read_port_transceiver_data(adapter, TR_PAGE_A0,
+ page_data);
+ if (!status) {
+ strlcpy(adapter->phy.vendor_name, page_data +
+ SFP_VENDOR_NAME_OFFSET, SFP_VENDOR_NAME_LEN - 1);
+ strlcpy(adapter->phy.vendor_pn,
+ page_data + SFP_VENDOR_PN_OFFSET,
+ SFP_VENDOR_NAME_LEN - 1);
+ }
+
+ return status;
+}
+
int lancer_cmd_delete_object(struct be_adapter *adapter, const char *obj_name)
{
struct lancer_cmd_req_delete_object *req;
@@ -3437,42 +3518,34 @@ err:
return status;
}
-int be_cmd_query_port_name(struct be_adapter *adapter, u8 *port_name)
+int be_cmd_query_port_name(struct be_adapter *adapter)
{
- struct be_mcc_wrb *wrb;
struct be_cmd_req_get_port_name *req;
+ struct be_mcc_wrb *wrb;
int status;
- if (!lancer_chip(adapter)) {
- *port_name = adapter->hba_port_num + '0';
- return 0;
- }
-
- spin_lock_bh(&adapter->mcc_lock);
-
- wrb = wrb_from_mccq(adapter);
- if (!wrb) {
- status = -EBUSY;
- goto err;
- }
+ if (mutex_lock_interruptible(&adapter->mbox_lock))
+ return -1;
+ wrb = wrb_from_mbox(adapter);
req = embedded_payload(wrb);
be_wrb_cmd_hdr_prepare(&req->hdr, CMD_SUBSYSTEM_COMMON,
OPCODE_COMMON_GET_PORT_NAME, sizeof(*req), wrb,
NULL);
- req->hdr.version = 1;
+ if (!BEx_chip(adapter))
+ req->hdr.version = 1;
- status = be_mcc_notify_wait(adapter);
+ status = be_mbox_notify_wait(adapter);
if (!status) {
struct be_cmd_resp_get_port_name *resp = embedded_payload(wrb);
- *port_name = resp->port_name[adapter->hba_port_num];
+ adapter->port_name = resp->port_name[adapter->hba_port_num];
} else {
- *port_name = adapter->hba_port_num + '0';
+ adapter->port_name = adapter->hba_port_num + '0';
}
-err:
- spin_unlock_bh(&adapter->mcc_lock);
+
+ mutex_unlock(&adapter->mbox_lock);
return status;
}
diff --git a/drivers/net/ethernet/emulex/benet/be_cmds.h b/drivers/net/ethernet/emulex/benet/be_cmds.h
index cf9d870..db761e8e 100644
--- a/drivers/net/ethernet/emulex/benet/be_cmds.h
+++ b/drivers/net/ethernet/emulex/benet/be_cmds.h
@@ -102,6 +102,8 @@ struct be_mcc_compl {
#define ASYNC_EVENT_PVID_STATE 0x3
#define ASYNC_EVENT_CODE_QNQ 0x6
#define ASYNC_DEBUG_EVENT_TYPE_QNQ 1
+#define ASYNC_EVENT_CODE_SLIPORT 0x11
+#define ASYNC_EVENT_PORT_MISCONFIG 0x9
enum {
LINK_DOWN = 0x0,
@@ -169,6 +171,15 @@ struct be_async_event_qnq {
u32 flags;
} __packed;
+#define INCOMPATIBLE_SFP 0x3
+/* async event indicating misconfigured port */
+struct be_async_event_misconfig_port {
+ u32 event_data_word1;
+ u32 event_data_word2;
+ u32 rsvd0;
+ u32 flags;
+} __packed;
+
struct be_mcc_mailbox {
struct be_mcc_wrb wrb;
struct be_mcc_compl compl;
@@ -1028,6 +1039,8 @@ enum {
#define SFP_PLUS_SFF_8472_COMP 0x5E
#define SFP_PLUS_CABLE_TYPE_OFFSET 0x8
#define SFP_PLUS_COPPER_CABLE 0x4
+#define SFP_VENDOR_NAME_OFFSET 0x14
+#define SFP_VENDOR_PN_OFFSET 0x28
#define PAGE_DATA_LEN 256
struct be_cmd_resp_port_type {
@@ -2259,6 +2272,7 @@ int be_cmd_get_beacon_state(struct be_adapter *adapter, u8 port_num,
int be_cmd_read_port_transceiver_data(struct be_adapter *adapter,
u8 page_num, u8 *data);
int be_cmd_query_cable_type(struct be_adapter *adapter);
+int be_cmd_query_sfp_info(struct be_adapter *adapter);
int be_cmd_write_flashrom(struct be_adapter *adapter, struct be_dma_mem *cmd,
u32 flash_oper, u32 flash_opcode, u32 img_offset,
u32 buf_size);
@@ -2326,7 +2340,7 @@ int lancer_initiate_dump(struct be_adapter *adapter);
int lancer_delete_dump(struct be_adapter *adapter);
bool dump_present(struct be_adapter *adapter);
int lancer_test_and_set_rdy_state(struct be_adapter *adapter);
-int be_cmd_query_port_name(struct be_adapter *adapter, u8 *port_name);
+int be_cmd_query_port_name(struct be_adapter *adapter);
int be_cmd_get_func_config(struct be_adapter *adapter,
struct be_resources *res);
int be_cmd_get_profile_config(struct be_adapter *adapter,
diff --git a/drivers/net/ethernet/emulex/benet/be_main.c b/drivers/net/ethernet/emulex/benet/be_main.c
index fbe7b6f..5936b24 100644
--- a/drivers/net/ethernet/emulex/benet/be_main.c
+++ b/drivers/net/ethernet/emulex/benet/be_main.c
@@ -3682,7 +3682,9 @@ static int be_get_config(struct be_adapter *adapter)
if (status)
return status;
- if (be_physfn(adapter)) {
+ be_cmd_query_port_name(adapter);
+
+ if (be_physfn(adapter)) {
status = be_cmd_get_active_profile(adapter, &profile_id);
if (!status)
dev_info(&adapter->pdev->dev,
@@ -5051,6 +5053,20 @@ static void be_func_recovery_task(struct work_struct *work)
msecs_to_jiffies(1000));
}
+static void be_log_sfp_info(struct be_adapter *adapter)
+{
+ int status;
+
+ status = be_cmd_query_sfp_info(adapter);
+ if (!status) {
+ dev_err(&adapter->pdev->dev,
+ "Unqualified SFP+ detected on %c from %s part no: %s",
+ adapter->port_name, adapter->phy.vendor_name,
+ adapter->phy.vendor_pn);
+ }
+ adapter->flags &= ~BE_FLAGS_EVT_INCOMPATIBLE_SFP;
+}
+
static void be_worker(struct work_struct *work)
{
struct be_adapter *adapter =
@@ -5089,6 +5105,9 @@ static void be_worker(struct work_struct *work)
be_eqd_update(adapter);
+ if (adapter->flags & BE_FLAGS_EVT_INCOMPATIBLE_SFP)
+ be_log_sfp_info(adapter);
+
reschedule:
adapter->work_counter++;
schedule_delayed_work(&adapter->work, msecs_to_jiffies(1000));
@@ -5157,10 +5176,9 @@ static inline char *nic_name(struct pci_dev *pdev)
static int be_probe(struct pci_dev *pdev, const struct pci_device_id *pdev_id)
{
- int status = 0;
struct be_adapter *adapter;
struct net_device *netdev;
- char port_name;
+ int status = 0;
dev_info(&pdev->dev, "%s version is %s\n", DRV_NAME, DRV_VER);
@@ -5254,10 +5272,8 @@ static int be_probe(struct pci_dev *pdev, const struct pci_device_id *pdev_id)
schedule_delayed_work(&adapter->func_recovery_work,
msecs_to_jiffies(1000));
- be_cmd_query_port_name(adapter, &port_name);
-
dev_info(&pdev->dev, "%s: %s %s port %c\n", nic_name(pdev),
- func_name(adapter), mc_name(adapter), port_name);
+ func_name(adapter), mc_name(adapter), adapter->port_name);
return 0;
--
2.2.0
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH net-next 9/9] be2net: avoid unncessary swapping of fields in eth_tx_wrb
2015-02-06 13:18 [PATCH net-next 0/9] be2net: patch set Sathya Perla
` (7 preceding siblings ...)
2015-02-06 13:18 ` [PATCH net-next 8/9] be2net: process port misconfig async event Sathya Perla
@ 2015-02-06 13:18 ` Sathya Perla
2015-02-08 6:52 ` [PATCH net-next 0/9] be2net: patch set David Miller
9 siblings, 0 replies; 14+ messages in thread
From: Sathya Perla @ 2015-02-06 13:18 UTC (permalink / raw)
To: netdev
The 32-bit fields of a tx-wrb are little endian. The driver is currently
using be_dws_le_to_cpu() routine to swap (cpu to le) all the fields of
a tx-wrb. So, the rsvd field is also unnecessarily swapped.
This patch fixes this by individually swapping the required fields.
Also, the type of the fields in eth_tx_wrb{} is now changed to __le32
from u32 to avoid sparse warnings.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
---
drivers/net/ethernet/emulex/benet/be_hw.h | 10 ++++-----
drivers/net/ethernet/emulex/benet/be_main.c | 35 ++++++++++++++++++-----------
2 files changed, 27 insertions(+), 18 deletions(-)
diff --git a/drivers/net/ethernet/emulex/benet/be_hw.h b/drivers/net/ethernet/emulex/benet/be_hw.h
index a8593aa..4884088 100644
--- a/drivers/net/ethernet/emulex/benet/be_hw.h
+++ b/drivers/net/ethernet/emulex/benet/be_hw.h
@@ -193,10 +193,10 @@ struct be_eq_entry {
/* TX Queue Descriptor */
#define ETH_WRB_FRAG_LEN_MASK 0xFFFF
struct be_eth_wrb {
- u32 frag_pa_hi; /* dword 0 */
- u32 frag_pa_lo; /* dword 1 */
- u32 rsvd0; /* dword 2 */
- u32 frag_len; /* dword 3: bits 0 - 15 */
+ __le32 frag_pa_hi; /* dword 0 */
+ __le32 frag_pa_lo; /* dword 1 */
+ u32 rsvd0; /* dword 2 */
+ __le32 frag_len; /* dword 3: bits 0 - 15 */
} __packed;
/* Pseudo amap definition for eth_hdr_wrb in which each bit of the
@@ -229,7 +229,7 @@ struct amap_eth_hdr_wrb {
#define TX_HDR_WRB_NUM_MASK 0x1F /* word 2: bits 13:17 */
struct be_eth_hdr_wrb {
- u32 dw[4];
+ __le32 dw[4];
};
/********* Tx Compl Status Encoding *********/
diff --git a/drivers/net/ethernet/emulex/benet/be_main.c b/drivers/net/ethernet/emulex/benet/be_main.c
index 5936b24..4abe2ab 100644
--- a/drivers/net/ethernet/emulex/benet/be_main.c
+++ b/drivers/net/ethernet/emulex/benet/be_main.c
@@ -682,9 +682,20 @@ static u32 skb_wrb_cnt(struct sk_buff *skb)
static inline void wrb_fill(struct be_eth_wrb *wrb, u64 addr, int len)
{
- wrb->frag_pa_hi = upper_32_bits(addr);
- wrb->frag_pa_lo = addr & 0xFFFFFFFF;
- wrb->frag_len = len & ETH_WRB_FRAG_LEN_MASK;
+ wrb->frag_pa_hi = cpu_to_le32(upper_32_bits(addr));
+ wrb->frag_pa_lo = cpu_to_le32(lower_32_bits(addr));
+ wrb->frag_len = cpu_to_le32(len & ETH_WRB_FRAG_LEN_MASK);
+ wrb->rsvd0 = 0;
+}
+
+/* A dummy wrb is just all zeros. Using a separate routine for dummy-wrb
+ * to avoid the swap and shift/mask operations in wrb_fill().
+ */
+static inline void wrb_fill_dummy(struct be_eth_wrb *wrb)
+{
+ wrb->frag_pa_hi = 0;
+ wrb->frag_pa_lo = 0;
+ wrb->frag_len = 0;
wrb->rsvd0 = 0;
}
@@ -765,16 +776,16 @@ static void unmap_tx_frag(struct device *dev, struct be_eth_wrb *wrb,
bool unmap_single)
{
dma_addr_t dma;
+ u32 frag_len = le32_to_cpu(wrb->frag_len);
- be_dws_le_to_cpu(wrb, sizeof(*wrb));
- dma = (u64)wrb->frag_pa_hi << 32 | (u64)wrb->frag_pa_lo;
- if (wrb->frag_len) {
+ dma = (u64)le32_to_cpu(wrb->frag_pa_hi) << 32 |
+ (u64)le32_to_cpu(wrb->frag_pa_lo);
+ if (frag_len) {
if (unmap_single)
- dma_unmap_single(dev, dma, wrb->frag_len,
- DMA_TO_DEVICE);
+ dma_unmap_single(dev, dma, frag_len, DMA_TO_DEVICE);
else
- dma_unmap_page(dev, dma, wrb->frag_len, DMA_TO_DEVICE);
+ dma_unmap_page(dev, dma, frag_len, DMA_TO_DEVICE);
}
}
@@ -806,7 +817,6 @@ static u32 be_xmit_enqueue(struct be_adapter *adapter, struct be_tx_obj *txo,
map_single = true;
wrb = queue_head_node(txq);
wrb_fill(wrb, busaddr, len);
- be_dws_cpu_to_le(wrb, sizeof(*wrb));
queue_head_inc(txq);
copied += len;
}
@@ -820,7 +830,6 @@ static u32 be_xmit_enqueue(struct be_adapter *adapter, struct be_tx_obj *txo,
goto dma_err;
wrb = queue_head_node(txq);
wrb_fill(wrb, busaddr, skb_frag_size(frag));
- be_dws_cpu_to_le(wrb, sizeof(*wrb));
queue_head_inc(txq);
copied += skb_frag_size(frag);
}
@@ -846,7 +855,7 @@ dma_err:
wrb = queue_head_node(txq);
unmap_tx_frag(dev, wrb, map_single);
map_single = false;
- copied -= wrb->frag_len;
+ copied -= le32_to_cpu(wrb->frag_len);
adapter->drv_stats.dma_map_errors++;
queue_head_inc(txq);
}
@@ -1037,7 +1046,7 @@ static void be_xmit_flush(struct be_adapter *adapter, struct be_tx_obj *txo)
/* compose a dummy wrb if there are odd set of wrbs to notify */
if (!lancer_chip(adapter) && (txo->pend_wrb_cnt & 1)) {
- wrb_fill(queue_head_node(txq), 0, 0);
+ wrb_fill_dummy(queue_head_node(txq));
queue_head_inc(txq);
atomic_inc(&txq->used);
txo->pend_wrb_cnt++;
--
2.2.0
^ permalink raw reply related [flat|nested] 14+ messages in thread* Re: [PATCH net-next 0/9] be2net: patch set
2015-02-06 13:18 [PATCH net-next 0/9] be2net: patch set Sathya Perla
` (8 preceding siblings ...)
2015-02-06 13:18 ` [PATCH net-next 9/9] be2net: avoid unncessary swapping of fields in eth_tx_wrb Sathya Perla
@ 2015-02-08 6:52 ` David Miller
9 siblings, 0 replies; 14+ messages in thread
From: David Miller @ 2015-02-08 6:52 UTC (permalink / raw)
To: sathya.perla; +Cc: netdev
From: Sathya Perla <sathya.perla@emulex.com>
Date: Fri, 6 Feb 2015 08:18:34 -0500
> Hi Dave, pls consider applying the following patch-set to the
> net-next tree. It has 5 code/style cleanup patches and 4 patches that
> add functionality to the driver.
Series applied.
^ permalink raw reply [flat|nested] 14+ messages in thread