From: Andrew Lunn <andrew@lunn.ch>
To: davem@davemloft.net, linux@roeck-us.net
Cc: netdev@vger.kernel.org, Andrew Lunn <andrew@lunn.ch>
Subject: [PATCH 1/2] net: dsa: mv88e6352: Refactor shareable code
Date: Sat, 14 Feb 2015 19:17:50 +0100 [thread overview]
Message-ID: <1423937871-9180-2-git-send-email-andrew@lunn.ch> (raw)
In-Reply-To: <1423937871-9180-1-git-send-email-andrew@lunn.ch>
The mv88e6352 allows access to the port phys via an internal mdio bus
which is accessed using registers in the GLOBAL 2 range. The mv88e6171
and probably other devices use the same mechanism. Move this code into
the shared mv88e6xxx.c library.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/dsa/mv88e6352.c | 77 +++++++--------------------------------------
drivers/net/dsa/mv88e6xxx.c | 53 +++++++++++++++++++++++++++++++
drivers/net/dsa/mv88e6xxx.h | 6 ++++
3 files changed, 71 insertions(+), 65 deletions(-)
diff --git a/drivers/net/dsa/mv88e6352.c b/drivers/net/dsa/mv88e6352.c
index e13adc7b3dda..1ebd8f96072a 100644
--- a/drivers/net/dsa/mv88e6352.c
+++ b/drivers/net/dsa/mv88e6352.c
@@ -22,59 +22,6 @@
#include <net/dsa.h>
#include "mv88e6xxx.h"
-static int mv88e6352_wait(struct dsa_switch *ds, int reg, int offset, u16 mask)
-{
- unsigned long timeout = jiffies + HZ / 10;
-
- while (time_before(jiffies, timeout)) {
- int ret;
-
- ret = REG_READ(reg, offset);
- if (!(ret & mask))
- return 0;
-
- usleep_range(1000, 2000);
- }
- return -ETIMEDOUT;
-}
-
-static inline int mv88e6352_phy_wait(struct dsa_switch *ds)
-{
- return mv88e6352_wait(ds, REG_GLOBAL2, 0x18, 0x8000);
-}
-
-static inline int mv88e6352_eeprom_load_wait(struct dsa_switch *ds)
-{
- return mv88e6352_wait(ds, REG_GLOBAL2, 0x14, 0x0800);
-}
-
-static inline int mv88e6352_eeprom_busy_wait(struct dsa_switch *ds)
-{
- return mv88e6352_wait(ds, REG_GLOBAL2, 0x14, 0x8000);
-}
-
-static int __mv88e6352_phy_read(struct dsa_switch *ds, int addr, int regnum)
-{
- int ret;
-
- REG_WRITE(REG_GLOBAL2, 0x18, 0x9800 | (addr << 5) | regnum);
-
- ret = mv88e6352_phy_wait(ds);
- if (ret < 0)
- return ret;
-
- return REG_READ(REG_GLOBAL2, 0x19);
-}
-
-static int __mv88e6352_phy_write(struct dsa_switch *ds, int addr, int regnum,
- u16 val)
-{
- REG_WRITE(REG_GLOBAL2, 0x19, val);
- REG_WRITE(REG_GLOBAL2, 0x18, 0x9400 | (addr << 5) | regnum);
-
- return mv88e6352_phy_wait(ds);
-}
-
static char *mv88e6352_probe(struct device *host_dev, int sw_addr)
{
struct mii_bus *bus = dsa_host_dev_to_mii_bus(host_dev);
@@ -346,12 +293,12 @@ static int mv88e6352_phy_page_read(struct dsa_switch *ds,
int ret;
mutex_lock(&ps->phy_mutex);
- ret = __mv88e6352_phy_write(ds, port, 0x16, page);
+ ret = mv88e6xxx_phy_write_indirect(ds, port, 0x16, page);
if (ret < 0)
goto error;
- ret = __mv88e6352_phy_read(ds, port, reg);
+ ret = mv88e6xxx_phy_read_indirect(ds, port, reg);
error:
- __mv88e6352_phy_write(ds, port, 0x16, 0x0);
+ mv88e6xxx_phy_write_indirect(ds, port, 0x16, 0x0);
mutex_unlock(&ps->phy_mutex);
return ret;
}
@@ -363,13 +310,13 @@ static int mv88e6352_phy_page_write(struct dsa_switch *ds,
int ret;
mutex_lock(&ps->phy_mutex);
- ret = __mv88e6352_phy_write(ds, port, 0x16, page);
+ ret = mv88e6xxx_phy_write_indirect(ds, port, 0x16, page);
if (ret < 0)
goto error;
- ret = __mv88e6352_phy_write(ds, port, reg, val);
+ ret = mv88e6xxx_phy_write_indirect(ds, port, reg, val);
error:
- __mv88e6352_phy_write(ds, port, 0x16, 0x0);
+ mv88e6xxx_phy_write_indirect(ds, port, 0x16, 0x0);
mutex_unlock(&ps->phy_mutex);
return ret;
}
@@ -482,7 +429,7 @@ mv88e6352_phy_read(struct dsa_switch *ds, int port, int regnum)
return addr;
mutex_lock(&ps->phy_mutex);
- ret = __mv88e6352_phy_read(ds, addr, regnum);
+ ret = mv88e6xxx_phy_read_indirect(ds, addr, regnum);
mutex_unlock(&ps->phy_mutex);
return ret;
@@ -499,7 +446,7 @@ mv88e6352_phy_write(struct dsa_switch *ds, int port, int regnum, u16 val)
return addr;
mutex_lock(&ps->phy_mutex);
- ret = __mv88e6352_phy_write(ds, addr, regnum, val);
+ ret = mv88e6xxx_phy_write_indirect(ds, addr, regnum, val);
mutex_unlock(&ps->phy_mutex);
return ret;
@@ -553,7 +500,7 @@ static int mv88e6352_read_eeprom_word(struct dsa_switch *ds, int addr)
if (ret < 0)
goto error;
- ret = mv88e6352_eeprom_busy_wait(ds);
+ ret = mv88e6xxx_eeprom_busy_wait(ds);
if (ret < 0)
goto error;
@@ -576,7 +523,7 @@ static int mv88e6352_get_eeprom(struct dsa_switch *ds,
eeprom->magic = 0xc3ec4951;
- ret = mv88e6352_eeprom_load_wait(ds);
+ ret = mv88e6xxx_eeprom_load_wait(ds);
if (ret < 0)
return ret;
@@ -657,7 +604,7 @@ static int mv88e6352_write_eeprom_word(struct dsa_switch *ds, int addr,
if (ret < 0)
goto error;
- ret = mv88e6352_eeprom_busy_wait(ds);
+ ret = mv88e6xxx_eeprom_busy_wait(ds);
error:
mutex_unlock(&ps->eeprom_mutex);
return ret;
@@ -681,7 +628,7 @@ static int mv88e6352_set_eeprom(struct dsa_switch *ds,
len = eeprom->len;
eeprom->len = 0;
- ret = mv88e6352_eeprom_load_wait(ds);
+ ret = mv88e6xxx_eeprom_load_wait(ds);
if (ret < 0)
return ret;
diff --git a/drivers/net/dsa/mv88e6xxx.c b/drivers/net/dsa/mv88e6xxx.c
index 3e7e31a6abb7..a83ace0803e7 100644
--- a/drivers/net/dsa/mv88e6xxx.c
+++ b/drivers/net/dsa/mv88e6xxx.c
@@ -596,6 +596,59 @@ error:
}
#endif /* CONFIG_NET_DSA_HWMON */
+static int mv88e6xxx_wait(struct dsa_switch *ds, int reg, int offset, u16 mask)
+{
+ unsigned long timeout = jiffies + HZ / 10;
+
+ while (time_before(jiffies, timeout)) {
+ int ret;
+
+ ret = REG_READ(reg, offset);
+ if (!(ret & mask))
+ return 0;
+
+ usleep_range(1000, 2000);
+ }
+ return -ETIMEDOUT;
+}
+
+int mv88e6xxx_phy_wait(struct dsa_switch *ds)
+{
+ return mv88e6xxx_wait(ds, REG_GLOBAL2, 0x18, 0x8000);
+}
+
+int mv88e6xxx_eeprom_load_wait(struct dsa_switch *ds)
+{
+ return mv88e6xxx_wait(ds, REG_GLOBAL2, 0x14, 0x0800);
+}
+
+int mv88e6xxx_eeprom_busy_wait(struct dsa_switch *ds)
+{
+ return mv88e6xxx_wait(ds, REG_GLOBAL2, 0x14, 0x8000);
+}
+
+int mv88e6xxx_phy_read_indirect(struct dsa_switch *ds, int addr, int regnum)
+{
+ int ret;
+
+ REG_WRITE(REG_GLOBAL2, 0x18, 0x9800 | (addr << 5) | regnum);
+
+ ret = mv88e6xxx_phy_wait(ds);
+ if (ret < 0)
+ return ret;
+
+ return REG_READ(REG_GLOBAL2, 0x19);
+}
+
+int mv88e6xxx_phy_write_indirect(struct dsa_switch *ds, int addr, int regnum,
+ u16 val)
+{
+ REG_WRITE(REG_GLOBAL2, 0x19, val);
+ REG_WRITE(REG_GLOBAL2, 0x18, 0x9400 | (addr << 5) | regnum);
+
+ return mv88e6xxx_phy_wait(ds);
+}
+
static int __init mv88e6xxx_init(void)
{
#if IS_ENABLED(CONFIG_NET_DSA_MV88E6131)
diff --git a/drivers/net/dsa/mv88e6xxx.h b/drivers/net/dsa/mv88e6xxx.h
index 03e397efde36..72942271bb67 100644
--- a/drivers/net/dsa/mv88e6xxx.h
+++ b/drivers/net/dsa/mv88e6xxx.h
@@ -82,6 +82,12 @@ int mv88e6xxx_get_regs_len(struct dsa_switch *ds, int port);
void mv88e6xxx_get_regs(struct dsa_switch *ds, int port,
struct ethtool_regs *regs, void *_p);
int mv88e6xxx_get_temp(struct dsa_switch *ds, int *temp);
+int mv88e6xxx_phy_wait(struct dsa_switch *ds);
+int mv88e6xxx_eeprom_load_wait(struct dsa_switch *ds);
+int mv88e6xxx_eeprom_busy_wait(struct dsa_switch *ds);
+int mv88e6xxx_phy_read_indirect(struct dsa_switch *ds, int addr, int regnum);
+int mv88e6xxx_phy_write_indirect(struct dsa_switch *ds, int addr, int regnum,
+ u16 val);
extern struct dsa_switch_driver mv88e6131_switch_driver;
extern struct dsa_switch_driver mv88e6123_61_65_switch_driver;
--
2.1.4
next prev parent reply other threads:[~2015-02-14 18:20 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-02-14 18:17 [PATCH 0/2] Indirect phy access for mv88e6171 Andrew Lunn
2015-02-14 18:17 ` Andrew Lunn [this message]
2015-02-16 3:09 ` [PATCH 1/2] net: dsa: mv88e6352: Refactor shareable code Guenter Roeck
2015-02-14 18:17 ` [PATCH 2/2] net: dsa: mv88e6171: Enable access to phys via internal mdio bus Andrew Lunn
2015-02-15 18:32 ` [PATCH 0/2] Indirect phy access for mv88e6171 Guenter Roeck
2015-02-15 20:25 ` Andrew Lunn
2015-02-15 21:05 ` Florian Fainelli
2015-02-15 22:20 ` Guenter Roeck
2015-02-19 20:54 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1423937871-9180-2-git-send-email-andrew@lunn.ch \
--to=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=linux@roeck-us.net \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).