From: Ondrej Zary <linux@rainbow-software.org>
To: netdev@vger.kernel.org
Cc: Francois Romieu <romieu@fr.zoreil.com>,
David Miller <davem@davemloft.net>,
Kernel development list <linux-kernel@vger.kernel.org>
Subject: [PATCH 2/3] dl2k: Reorder and cleanup initialization
Date: Thu, 19 Nov 2015 20:13:05 +0100 [thread overview]
Message-ID: <1447960386-3049-2-git-send-email-linux@rainbow-software.org> (raw)
In-Reply-To: <1447960386-3049-1-git-send-email-linux@rainbow-software.org>
Move HW init and stop into separate functions.
Request IRQ only after the HW has been reset (so interrupts are
disabled and no stale interrupts are pending).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
---
drivers/net/ethernet/dlink/dl2k.c | 95 ++++++++++++++++++++++---------------
1 file changed, 56 insertions(+), 39 deletions(-)
diff --git a/drivers/net/ethernet/dlink/dl2k.c b/drivers/net/ethernet/dlink/dl2k.c
index ec0eb7f..9e9baa0 100644
--- a/drivers/net/ethernet/dlink/dl2k.c
+++ b/drivers/net/ethernet/dlink/dl2k.c
@@ -252,19 +252,6 @@ rio_probe1 (struct pci_dev *pdev, const struct pci_device_id *ent)
if (err)
goto err_out_unmap_rx;
- if (np->chip_id == CHIP_IP1000A &&
- (np->pdev->revision == 0x40 || np->pdev->revision == 0x41)) {
- /* PHY magic taken from ipg driver, undocumented registers */
- mii_write(dev, np->phy_addr, 31, 0x0001);
- mii_write(dev, np->phy_addr, 27, 0x01e0);
- mii_write(dev, np->phy_addr, 31, 0x0002);
- mii_write(dev, np->phy_addr, 27, 0xeb8e);
- mii_write(dev, np->phy_addr, 31, 0x0000);
- mii_write(dev, np->phy_addr, 30, 0x005e);
- /* advertise 1000BASE-T half & full duplex, prefer MASTER */
- mii_write(dev, np->phy_addr, MII_CTRL1000, 0x0700);
- }
-
/* Fiber device? */
np->phy_media = (dr16(ASICCtrl) & PhyMedia) ? 1 : 0;
np->link_status = 0;
@@ -274,13 +261,11 @@ rio_probe1 (struct pci_dev *pdev, const struct pci_device_id *ent)
if (np->an_enable == 2) {
np->an_enable = 1;
}
- mii_set_media_pcs (dev);
} else {
/* Auto-Negotiation is mandatory for 1000BASE-T,
IEEE 802.3ab Annex 28D page 14 */
if (np->speed == 1000)
np->an_enable = 1;
- mii_set_media (dev);
}
err = register_netdev (dev);
@@ -531,25 +516,13 @@ static int alloc_list(struct net_device *dev)
return 0;
}
-static int
-rio_open (struct net_device *dev)
+static void rio_hw_init(struct net_device *dev)
{
struct netdev_private *np = netdev_priv(dev);
void __iomem *ioaddr = np->ioaddr;
- const int irq = np->pdev->irq;
int i;
u16 macctrl;
- i = alloc_list(dev);
- if (i)
- return i;
-
- i = request_irq(irq, rio_interrupt, IRQF_SHARED, dev->name, dev);
- if (i) {
- free_list(dev);
- return i;
- }
-
/* Reset all logic functions */
dw16(ASICCtrl + 2,
GlobalReset | DMAReset | FIFOReset | NetworkReset | HostReset);
@@ -560,6 +533,24 @@ rio_open (struct net_device *dev)
/* DebugCtrl bit 4, 5, 9 must set */
dw32(DebugCtrl, dr32(DebugCtrl) | 0x0230);
+ if (np->chip_id == CHIP_IP1000A &&
+ (np->pdev->revision == 0x40 || np->pdev->revision == 0x41)) {
+ /* PHY magic taken from ipg driver, undocumented registers */
+ mii_write(dev, np->phy_addr, 31, 0x0001);
+ mii_write(dev, np->phy_addr, 27, 0x01e0);
+ mii_write(dev, np->phy_addr, 31, 0x0002);
+ mii_write(dev, np->phy_addr, 27, 0xeb8e);
+ mii_write(dev, np->phy_addr, 31, 0x0000);
+ mii_write(dev, np->phy_addr, 30, 0x005e);
+ /* advertise 1000BASE-T half & full duplex, prefer MASTER */
+ mii_write(dev, np->phy_addr, MII_CTRL1000, 0x0700);
+ }
+
+ if (np->phy_media)
+ mii_set_media_pcs(dev);
+ else
+ mii_set_media(dev);
+
/* Jumbo frame */
if (np->jumbo != 0)
dw16(MaxFrameSize, MAX_JUMBO+14);
@@ -602,10 +593,6 @@ rio_open (struct net_device *dev)
dw32(MACCtrl, dr32(MACCtrl) | AutoVLANuntagging);
}
- setup_timer(&np->timer, rio_timer, (unsigned long)dev);
- np->timer.expires = jiffies + 1*HZ;
- add_timer (&np->timer);
-
/* Start Tx/Rx */
dw32(MACCtrl, dr32(MACCtrl) | StatsEnable | RxEnable | TxEnable);
@@ -615,6 +602,42 @@ rio_open (struct net_device *dev)
macctrl |= (np->tx_flow) ? TxFlowControlEnable : 0;
macctrl |= (np->rx_flow) ? RxFlowControlEnable : 0;
dw16(MACCtrl, macctrl);
+}
+
+static void rio_hw_stop(struct net_device *dev)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ void __iomem *ioaddr = np->ioaddr;
+
+ /* Disable interrupts */
+ dw16(IntEnable, 0);
+
+ /* Stop Tx and Rx logics */
+ dw32(MACCtrl, TxDisable | RxDisable | StatsDisable);
+}
+
+static int rio_open(struct net_device *dev)
+{
+ struct netdev_private *np = netdev_priv(dev);
+ const int irq = np->pdev->irq;
+ int i;
+
+ i = alloc_list(dev);
+ if (i)
+ return i;
+
+ rio_hw_init(dev);
+
+ i = request_irq(irq, rio_interrupt, IRQF_SHARED, dev->name, dev);
+ if (i) {
+ rio_hw_stop(dev);
+ free_list(dev);
+ return i;
+ }
+
+ setup_timer(&np->timer, rio_timer, (unsigned long)dev);
+ np->timer.expires = jiffies + 1 * HZ;
+ add_timer(&np->timer);
netif_start_queue (dev);
@@ -1764,17 +1787,11 @@ static int
rio_close (struct net_device *dev)
{
struct netdev_private *np = netdev_priv(dev);
- void __iomem *ioaddr = np->ioaddr;
-
struct pci_dev *pdev = np->pdev;
netif_stop_queue (dev);
- /* Disable interrupts */
- dw16(IntEnable, 0);
-
- /* Stop Tx and Rx logics */
- dw32(MACCtrl, TxDisable | RxDisable | StatsDisable);
+ rio_hw_stop(dev);
free_irq(pdev->irq, dev);
del_timer_sync (&np->timer);
--
Ondrej Zary
next prev parent reply other threads:[~2015-11-19 19:13 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-11-19 19:13 [PATCH 1/3 v2] dl2k: Handle memory allocation errors in alloc_list Ondrej Zary
2015-11-19 19:13 ` Ondrej Zary [this message]
2015-11-20 19:49 ` [PATCH 2/3] dl2k: Reorder and cleanup initialization David Miller
2015-11-19 19:13 ` [PATCH 3/3 v3] dl2k: Implement suspend Ondrej Zary
2015-11-20 19:49 ` David Miller
2015-11-20 19:48 ` [PATCH 1/3 v2] dl2k: Handle memory allocation errors in alloc_list David Miller
-- strict thread matches above, loose matches on Subject: below --
2015-11-18 21:36 Ondrej Zary
2015-11-18 21:36 ` [PATCH 2/3] dl2k: Reorder and cleanup initialization Ondrej Zary
2015-11-17 17:28 [PATCH 1/3] dl2k: Handle memory allocation errors in alloc_list Ondrej Zary
2015-11-17 17:28 ` [PATCH 2/3] dl2k: Reorder and cleanup initialization Ondrej Zary
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1447960386-3049-2-git-send-email-linux@rainbow-software.org \
--to=linux@rainbow-software.org \
--cc=davem@davemloft.net \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=romieu@fr.zoreil.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).