* [PATCH 1/2] ethtool-copy.h: sync with net
2016-02-17 20:37 [PATCH 0/2] Add support for PHY packet generator to ethtool(1) Andrew Lunn
@ 2016-02-17 20:37 ` Andrew Lunn
2016-02-17 20:37 ` [PATCH 2/2] ethtool: Add --phy_pkt_gen command Andrew Lunn
1 sibling, 0 replies; 4+ messages in thread
From: Andrew Lunn @ 2016-02-17 20:37 UTC (permalink / raw)
To: Ben Hutchings; +Cc: Florian Fainelli, netdev, Andrew Lunn
Additional, add MAX_INT to internal.h, which is now required by
ethtool-copy.h.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
ethtool-copy.h | 119 ++++++++++++++++++++++++++++++++++++++++++++++++++++-----
internal.h | 3 ++
2 files changed, 113 insertions(+), 9 deletions(-)
diff --git a/ethtool-copy.h b/ethtool-copy.h
index 57fa390..bce6c95 100644
--- a/ethtool-copy.h
+++ b/ethtool-copy.h
@@ -31,7 +31,7 @@
* physical connectors and other link features that are
* advertised through autonegotiation or enabled for
* auto-detection.
- * @speed: Low bits of the speed
+ * @speed: Low bits of the speed, 1Mb units, 0 to INT_MAX or SPEED_UNKNOWN
* @duplex: Duplex mode; one of %DUPLEX_*
* @port: Physical connector type; one of %PORT_*
* @phy_address: MDIO address of PHY (transceiver); 0 or 255 if not
@@ -47,7 +47,7 @@
* obsoleted by &struct ethtool_coalesce. Read-only; deprecated.
* @maxrxpkt: Historically used to report RX IRQ coalescing; now
* obsoleted by &struct ethtool_coalesce. Read-only; deprecated.
- * @speed_hi: High bits of the speed
+ * @speed_hi: High bits of the speed, 1Mb units, 0 to INT_MAX or SPEED_UNKNOWN
* @eth_tp_mdix: Ethernet twisted-pair MDI(-X) status; one of
* %ETH_TP_MDI_*. If the status is unknown or not applicable, the
* value will be %ETH_TP_MDI_INVALID. Read-only.
@@ -748,6 +748,56 @@ struct ethtool_usrip4_spec {
__u8 proto;
};
+/**
+ * struct ethtool_tcpip6_spec - flow specification for TCP/IPv6 etc.
+ * @ip6src: Source host
+ * @ip6dst: Destination host
+ * @psrc: Source port
+ * @pdst: Destination port
+ * @tclass: Traffic Class
+ *
+ * This can be used to specify a TCP/IPv6, UDP/IPv6 or SCTP/IPv6 flow.
+ */
+struct ethtool_tcpip6_spec {
+ __be32 ip6src[4];
+ __be32 ip6dst[4];
+ __be16 psrc;
+ __be16 pdst;
+ __u8 tclass;
+};
+
+/**
+ * struct ethtool_ah_espip6_spec - flow specification for IPsec/IPv6
+ * @ip6src: Source host
+ * @ip6dst: Destination host
+ * @spi: Security parameters index
+ * @tclass: Traffic Class
+ *
+ * This can be used to specify an IPsec transport or tunnel over IPv6.
+ */
+struct ethtool_ah_espip6_spec {
+ __be32 ip6src[4];
+ __be32 ip6dst[4];
+ __be32 spi;
+ __u8 tclass;
+};
+
+/**
+ * struct ethtool_usrip6_spec - general flow specification for IPv6
+ * @ip6src: Source host
+ * @ip6dst: Destination host
+ * @l4_4_bytes: First 4 bytes of transport (layer 4) header
+ * @tclass: Traffic Class
+ * @l4_proto: Transport protocol number (nexthdr after any Extension Headers)
+ */
+struct ethtool_usrip6_spec {
+ __be32 ip6src[4];
+ __be32 ip6dst[4];
+ __be32 l4_4_bytes;
+ __u8 tclass;
+ __u8 l4_proto;
+};
+
union ethtool_flow_union {
struct ethtool_tcpip4_spec tcp_ip4_spec;
struct ethtool_tcpip4_spec udp_ip4_spec;
@@ -755,6 +805,12 @@ union ethtool_flow_union {
struct ethtool_ah_espip4_spec ah_ip4_spec;
struct ethtool_ah_espip4_spec esp_ip4_spec;
struct ethtool_usrip4_spec usr_ip4_spec;
+ struct ethtool_tcpip6_spec tcp_ip6_spec;
+ struct ethtool_tcpip6_spec udp_ip6_spec;
+ struct ethtool_tcpip6_spec sctp_ip6_spec;
+ struct ethtool_ah_espip6_spec ah_ip6_spec;
+ struct ethtool_ah_espip6_spec esp_ip6_spec;
+ struct ethtool_usrip6_spec usr_ip6_spec;
struct ethhdr ether_spec;
__u8 hdata[52];
};
@@ -1111,6 +1167,31 @@ struct ethtool_ts_info {
__u32 rx_reserved[3];
};
+enum ethtool_phy_pkg_gen_flags {
+ ETH_PKT_RANDOM = (1 << 0),
+ ETH_PKT_ERROR = (1 << 1),
+};
+
+/**
+ * struct ethtool_phy_pkt_get - command to request the phy to generate packets.
+ * @cmd: command number = %ETHTOOL_PHY_PKT_GEN
+ * @count: number of packets to generate
+ * @len: length of generated packets
+ * @ipg: inter packet gap in bytes.
+ * @flags: a bitmask of flags from &enum ethtool_phy_pkg_gen_flags
+ *
+ * PHY drivers may not support all of these parameters. If the
+ * requested parameter value cannot be supported an error should be
+ * returned.
+ */
+struct ethtool_phy_pkt_gen {
+ __u32 cmd;
+ __u32 count;
+ __u32 len;
+ __u32 ipg;
+ __u32 flags;
+};
+
/*
* %ETHTOOL_SFEATURES changes features present in features[].valid to the
* values of corresponding bits in features[].requested. Bits in .requested
@@ -1228,6 +1309,7 @@ enum ethtool_sfeatures_retval_bits {
#define ETHTOOL_GTUNABLE 0x00000048 /* Get tunable configuration */
#define ETHTOOL_STUNABLE 0x00000049 /* Set tunable configuration */
#define ETHTOOL_GPHYSTATS 0x0000004a /* get PHY-specific statistics */
+#define ETHTOOL_PHY_PKT_GEN 0x0000004b /* Gnerate packets in the PHY */
/* compatibility with older code */
#define SPARC_ETH_GSET ETHTOOL_GSET
@@ -1303,7 +1385,7 @@ enum ethtool_sfeatures_retval_bits {
* it was forced up into this mode or autonegotiated.
*/
-/* The forced speed, 10Mb, 100Mb, gigabit, [2.5|5|10|20|25|40|50|56|100]GbE. */
+/* The forced speed, in units of 1Mb. All values 0 to INT_MAX are legal. */
#define SPEED_10 10
#define SPEED_100 100
#define SPEED_1000 1000
@@ -1319,11 +1401,28 @@ enum ethtool_sfeatures_retval_bits {
#define SPEED_UNKNOWN -1
+static inline int ethtool_validate_speed(__u32 speed)
+{
+ return speed <= INT_MAX || speed == SPEED_UNKNOWN;
+}
+
/* Duplex, half or full. */
#define DUPLEX_HALF 0x00
#define DUPLEX_FULL 0x01
#define DUPLEX_UNKNOWN 0xff
+static inline int ethtool_validate_duplex(__u8 duplex)
+{
+ switch (duplex) {
+ case DUPLEX_HALF:
+ case DUPLEX_FULL:
+ case DUPLEX_UNKNOWN:
+ return 1;
+ }
+
+ return 0;
+}
+
/* Which connector port. */
#define PORT_TP 0x00
#define PORT_AUI 0x01
@@ -1367,15 +1466,17 @@ enum ethtool_sfeatures_retval_bits {
#define UDP_V4_FLOW 0x02 /* hash or spec (udp_ip4_spec) */
#define SCTP_V4_FLOW 0x03 /* hash or spec (sctp_ip4_spec) */
#define AH_ESP_V4_FLOW 0x04 /* hash only */
-#define TCP_V6_FLOW 0x05 /* hash only */
-#define UDP_V6_FLOW 0x06 /* hash only */
-#define SCTP_V6_FLOW 0x07 /* hash only */
+#define TCP_V6_FLOW 0x05 /* hash or spec (tcp_ip6_spec; nfc only) */
+#define UDP_V6_FLOW 0x06 /* hash or spec (udp_ip6_spec; nfc only) */
+#define SCTP_V6_FLOW 0x07 /* hash or spec (sctp_ip6_spec; nfc only) */
#define AH_ESP_V6_FLOW 0x08 /* hash only */
#define AH_V4_FLOW 0x09 /* hash or spec (ah_ip4_spec) */
#define ESP_V4_FLOW 0x0a /* hash or spec (esp_ip4_spec) */
-#define AH_V6_FLOW 0x0b /* hash only */
-#define ESP_V6_FLOW 0x0c /* hash only */
-#define IP_USER_FLOW 0x0d /* spec only (usr_ip4_spec) */
+#define AH_V6_FLOW 0x0b /* hash or spec (ah_ip6_spec; nfc only) */
+#define ESP_V6_FLOW 0x0c /* hash or spec (esp_ip6_spec; nfc only) */
+#define IPV4_USER_FLOW 0x0d /* spec only (usr_ip4_spec) */
+#define IP_USER_FLOW IPV4_USER_FLOW
+#define IPV6_USER_FLOW 0x0e /* spec only (usr_ip6_spec; nfc only) */
#define IPV4_FLOW 0x10 /* hash only */
#define IPV6_FLOW 0x11 /* hash only */
#define ETHER_FLOW 0x12 /* spec only (ether_spec) */
diff --git a/internal.h b/internal.h
index b5ef646..ce137fe 100644
--- a/internal.h
+++ b/internal.h
@@ -29,6 +29,9 @@ typedef uint16_t u16;
typedef uint8_t u8;
typedef int32_t s32;
+/* and from <linux/kernel.h> */
+#define INT_MAX ((int)(~0U>>1))
+
#include "ethtool-copy.h"
#include "net_tstamp-copy.h"
--
2.1.4
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH 2/2] ethtool: Add --phy_pkt_gen command
2016-02-17 20:37 [PATCH 0/2] Add support for PHY packet generator to ethtool(1) Andrew Lunn
2016-02-17 20:37 ` [PATCH 1/2] ethtool-copy.h: sync with net Andrew Lunn
@ 2016-02-17 20:37 ` Andrew Lunn
2016-02-17 21:08 ` Ben Hutchings
1 sibling, 1 reply; 4+ messages in thread
From: Andrew Lunn @ 2016-02-17 20:37 UTC (permalink / raw)
To: Ben Hutchings; +Cc: Florian Fainelli, netdev, Andrew Lunn
This command is used to cause the PHY to generate packets. The count
of packets must always be given. Optionally, the length of the packet,
if the packet should contain random or fixed data, if errored packets should
be sent and the inter packet gap can be configured. However not all PHYs
are expected to support all options.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
ethtool.8.in | 30 ++++++++++++++++++++++++++++++
ethtool.c | 44 ++++++++++++++++++++++++++++++++++++++++++++
2 files changed, 74 insertions(+)
diff --git a/ethtool.8.in b/ethtool.8.in
index 2316556..ec5ca80 100644
--- a/ethtool.8.in
+++ b/ethtool.8.in
@@ -339,6 +339,14 @@ ethtool \- query or control network driver and hardware settings
.B2 tx-lpi on off
.BN tx-timer
.BN advertise
+.HP
+.B ethtool \-\-phy\-pkt\-gen
+.I devname
+.I count
+.B2 random on off
+.BN len
+.B2 error off on
+.BN ipg
.
.\" Adjust lines (i.e. full justification) and hyphenate.
.ad
@@ -885,6 +893,28 @@ Values are as for
.BI tx-timer \ N
Sets the amount of time the device should stay in idle mode prior to asserting
its Tx LPI (in microseconds). This has meaning only when Tx LPI is enabled.
+.TP
+.B \-\-phy\-pkt\-get\-eee
+Cause the PHY to generate packets using its in built packet
+generator. PHYs may not support all options and may differ on
+supported packet size, packet contents, etc.
+.TP
+.I count
+Number of packets to send. Typically this can be between 1 and 255.
+.TP
+.A2 random on off
+Send packets with random contents, or fixed. Fixed content packets
+often contain 0x5a,0xa5,0x5a,0xa5,... but may have different contents.
+.TP
+.BI len \ N
+Length of the packet to send, typically 64 or 1518 bytes, but other
+lengths may be supported.
+.TP
+.A2 error off on
+Generate packets with errors.
+.TP
+.BI ipg \ N
+Set the inter packet gap length, in bytes.
.SH BUGS
Not supported (in part or whole) on all network drivers.
.SH AUTHOR
diff --git a/ethtool.c b/ethtool.c
index 480c14c..448395f 100644
--- a/ethtool.c
+++ b/ethtool.c
@@ -4046,6 +4046,44 @@ static int do_seee(struct cmd_context *ctx)
return 0;
}
+static int do_phy_pkt_gen(struct cmd_context *ctx)
+{
+ struct ethtool_phy_pkt_gen cmd;
+ int random, error, changed;
+ struct cmdline_info cmdline_phy_pkt_gen[] = {
+ { "random", CMDL_BOOL, &random, NULL },
+ { "len", CMDL_U32, &cmd.len, NULL },
+ { "error", CMDL_BOOL, &error, NULL },
+ { "ipg", CMDL_U32, &cmd.ipg, NULL },
+ };
+
+ if (ctx->argc < 1)
+ exit_bad_args();
+
+ memset(&cmd, 0, sizeof(cmd));
+
+ cmd.count = get_uint_range(ctx->argp[0], 0, 0xffffffff);
+ ctx->argc--;
+ ctx->argp++;
+
+ parse_generic_cmdline(ctx, &changed, cmdline_phy_pkt_gen,
+ ARRAY_SIZE(cmdline_phy_pkt_gen));
+
+ cmd.cmd = ETHTOOL_PHY_PKT_GEN;
+ cmd.flags = 0;
+ if (error)
+ cmd.flags |= ETH_PKT_ERROR;
+ if (random)
+ cmd.flags |= ETH_PKT_RANDOM;
+
+ if (send_ioctl(ctx, &cmd)) {
+ perror("Cannot perform PHY packet generation");
+ return 1;
+ }
+
+ return 0;
+}
+
#ifndef TEST_ETHTOOL
int send_ioctl(struct cmd_context *ctx, void *cmd)
{
@@ -4205,6 +4243,12 @@ static const struct option {
" [ advertise %x ]\n"
" [ tx-lpi on|off ]\n"
" [ tx-timer %d ]\n"},
+ { "--phy-pkt-gen", 1, do_phy_pkt_gen, "PHY packet generation",
+ " count\n"
+ " [ random on|off ]\n"
+ " [ len N ]\n"
+ " [ error off|on ]\n"
+ " [ ipg N ]\n" },
{ "-h|--help", 0, show_usage, "Show this help" },
{ "--version", 0, do_version, "Show version number" },
{}
--
2.1.4
^ permalink raw reply related [flat|nested] 4+ messages in thread