[PATCH net-next 1/2] net: l3mdev: address selection should only consider devices in L3 domain

[PATCH net-next 1/2] net: l3mdev: address selection should only consider devices in L3 domain

[David Ahern]

David Lamparter noted a use case where the source address selection fails
to pick an address from a VRF interface - unnumbered interfaces.

Relevant commands from his script:
    ip addr add 9.9.9.9/32 dev lo
    ip link set lo up

    ip link add name vrf0 type vrf table 101
    ip rule add oif vrf0 table 101
    ip rule add iif vrf0 table 101
    ip link set vrf0 up
    ip addr add 10.0.0.3/32 dev vrf0

    ip link add name dummy2 type dummy
    ip link set dummy2 master vrf0 up

    --> note dummy2 has no address - unnumbered device

    ip route add 10.2.2.2/32 dev dummy2 table 101
    ip neigh add 10.2.2.2 dev dummy2 lladdr 02:00:00:00:00:02

    tcpdump -ni dummy2 &

And using ping instead of his socat example:
    $ ping -I vrf0 -c1 10.2.2.2
    ping: Warning: source address might be selected on device other than vrf0.
    PING 10.2.2.2 (10.2.2.2) from 9.9.9.9 vrf0: 56(84) bytes of data.

>From tcpdump:
    12:57:29.449128 IP 9.9.9.9 > 10.2.2.2: ICMP echo request, id 2491, seq 1, length 64

Note the source address is from lo and is not a VRF local address. With
this patch:

    $ ping -I vrf0 -c1 10.2.2.2
    PING 10.2.2.2 (10.2.2.2) from 10.0.0.3 vrf0: 56(84) bytes of data.

>From tcpdump:
    12:59:25.096426 IP 10.0.0.3 > 10.2.2.2: ICMP echo request, id 2113, seq 1, length 64

Now the source address comes from vrf0.

The ipv4 function for selecting source address takes a const argument.
Removing the const requires touching a lot of places, so instead
l3mdev_master_ifindex_rcu is changed to take a const argument and then
do the typecast to non-const as required by netdev_master_upper_dev_get_rcu.
This is similar to what l3mdev_fib_table_rcu does.

IPv6 for unnumbered interfaces appears to be selecting the addresses
properly.

Cc: David Lamparter <david@opensourcerouting.org>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
---
No changes from last version.

 include/net/l3mdev.h |  4 ++--
 net/ipv4/devinet.c   |  5 +++++
 net/l3mdev/l3mdev.c  | 11 +++++++++--
 3 files changed, 16 insertions(+), 4 deletions(-)

diff --git a/include/net/l3mdev.h b/include/net/l3mdev.h
index 5567d46b3cff..c43a9c73de5e 100644
--- a/include/net/l3mdev.h
+++ b/include/net/l3mdev.h
@@ -39,7 +39,7 @@ struct l3mdev_ops {
 
 #ifdef CONFIG_NET_L3_MASTER_DEV
 
-int l3mdev_master_ifindex_rcu(struct net_device *dev);
+int l3mdev_master_ifindex_rcu(const struct net_device *dev);
 static inline int l3mdev_master_ifindex(struct net_device *dev)
 {
 	int ifindex;
@@ -179,7 +179,7 @@ struct dst_entry *l3mdev_rt6_dst_by_oif(struct net *net,
 
 #else
 
-static inline int l3mdev_master_ifindex_rcu(struct net_device *dev)
+static inline int l3mdev_master_ifindex_rcu(const struct net_device *dev)
 {
 	return 0;
 }
diff --git a/net/ipv4/devinet.c b/net/ipv4/devinet.c
index 3d835313575e..614904c29cbd 100644
--- a/net/ipv4/devinet.c
+++ b/net/ipv4/devinet.c
@@ -1194,6 +1194,7 @@ __be32 inet_select_addr(const struct net_device *dev, __be32 dst, int scope)
 	__be32 addr = 0;
 	struct in_device *in_dev;
 	struct net *net = dev_net(dev);
+	int master_idx;
 
 	rcu_read_lock();
 	in_dev = __in_dev_get_rcu(dev);
@@ -1214,12 +1215,16 @@ __be32 inet_select_addr(const struct net_device *dev, __be32 dst, int scope)
 	if (addr)
 		goto out_unlock;
 no_in_dev:
+	master_idx = l3mdev_master_ifindex_rcu(dev);
 
 	/* Not loopback addresses on loopback should be preferred
 	   in this case. It is important that lo is the first interface
 	   in dev_base list.
 	 */
 	for_each_netdev_rcu(net, dev) {
+		if (l3mdev_master_ifindex_rcu(dev) != master_idx)
+			continue;
+
 		in_dev = __in_dev_get_rcu(dev);
 		if (!in_dev)
 			continue;
diff --git a/net/l3mdev/l3mdev.c b/net/l3mdev/l3mdev.c
index 8e5ead366e7f..e925037fa0df 100644
--- a/net/l3mdev/l3mdev.c
+++ b/net/l3mdev/l3mdev.c
@@ -17,7 +17,7 @@
  *	@dev: targeted interface
  */
 
-int l3mdev_master_ifindex_rcu(struct net_device *dev)
+int l3mdev_master_ifindex_rcu(const struct net_device *dev)
 {
 	int ifindex = 0;
 
@@ -28,8 +28,15 @@ int l3mdev_master_ifindex_rcu(struct net_device *dev)
 		ifindex = dev->ifindex;
 	} else if (netif_is_l3_slave(dev)) {
 		struct net_device *master;
+		struct net_device *_dev = (struct net_device *)dev;
 
-		master = netdev_master_upper_dev_get_rcu(dev);
+		/* netdev_master_upper_dev_get_rcu calls
+		 * list_first_or_null_rcu to walk the upper dev list.
+		 * list_first_or_null_rcu does not handle a const arg. We aren't
+		 * making changes, just want the master device from that list so
+		 * typecast to remove the const
+		 */
+		master = netdev_master_upper_dev_get_rcu(_dev);
 		if (master)
 			ifindex = master->ifindex;
 	}
-- 
2.1.4

[PATCH net-next v3 0/2] net: l3mdev: Fix source address for unnumbered deployments

[David Ahern]

David Lamparter noted a use case where the source address selection fails
to pick an address from a VRF interface - unnumbered interfaces. The use
case has the VRF device as the VRF local loopback with addresses and
interfaces enslaved without an address themselves. e.g,

    ip addr add 9.9.9.9/32 dev lo
    ip link set lo up

    ip link add name vrf0 type vrf table 101
    ip rule add oif vrf0 table 101
    ip rule add iif vrf0 table 101
    ip link set vrf0 up
    ip addr add 10.0.0.3/32 dev vrf0

    ip link add name dummy2 type dummy
    ip link set dummy2 master vrf0 up

    --> note dummy2 has no address - unnumbered device

    ip route add 10.2.2.2/32 dev dummy2 table 101
    ip neigh add 10.2.2.2 dev dummy2 lladdr 02:00:00:00:00:02

ping to the 10.2.2.2 through the L3 domain:

    $ ping -I vrf0 -c1 10.2.2.2
    ping: Warning: source address might be selected on device other than vrf0.
    PING 10.2.2.2 (10.2.2.2) from 9.9.9.9 vrf0: 56(84) bytes of data.

picks up the wrong address -- the one from 'lo' not vrf0. And from tcpdump:
    12:57:29.449128 IP 9.9.9.9 > 10.2.2.2: ICMP echo request, id 2491, seq 1, length 64

This patch series changes address selection to only consider devices in
the same L3 domain and to use the VRF device as the L3 domains loopback.

    $ ping -I vrf0 -c1 10.2.2.2
    PING 10.2.2.2 (10.2.2.2) from 10.0.0.3 vrf0: 56(84) bytes of data.

>From tcpdump:
    12:59:25.096426 IP 10.0.0.3 > 10.2.2.2: ICMP echo request, id 2113, seq 1, length 64

Now the source address comes from vrf0.

David Ahern (1):
  net: l3mdev: address selection should only consider devices in L3
    domain

David Lamparter (1):
  net: l3mdev: prefer VRF master for source address selection

 include/net/l3mdev.h |  4 ++--
 net/ipv4/devinet.c   | 22 ++++++++++++++++++++++
 net/l3mdev/l3mdev.c  | 11 +++++++++--
 3 files changed, 33 insertions(+), 4 deletions(-)

-- 
2.1.4

[PATCH net-next 1/2] net: l3mdev: address selection should only consider devices in L3 domain

[David Ahern]

David Lamparter noted a use case where the source address selection fails
to pick an address from a VRF interface - unnumbered interfaces.

Relevant commands from his script:
    ip addr add 9.9.9.9/32 dev lo
    ip link set lo up

    ip link add name vrf0 type vrf table 101
    ip rule add oif vrf0 table 101
    ip rule add iif vrf0 table 101
    ip link set vrf0 up
    ip addr add 10.0.0.3/32 dev vrf0

    ip link add name dummy2 type dummy
    ip link set dummy2 master vrf0 up

    --> note dummy2 has no address - unnumbered device

    ip route add 10.2.2.2/32 dev dummy2 table 101
    ip neigh add 10.2.2.2 dev dummy2 lladdr 02:00:00:00:00:02

    tcpdump -ni dummy2 &

And using ping instead of his socat example:
    $ ping -I vrf0 -c1 10.2.2.2
    ping: Warning: source address might be selected on device other than vrf0.
    PING 10.2.2.2 (10.2.2.2) from 9.9.9.9 vrf0: 56(84) bytes of data.

>From tcpdump:
    12:57:29.449128 IP 9.9.9.9 > 10.2.2.2: ICMP echo request, id 2491, seq 1, length 64

Note the source address is from lo and is not a VRF local address. With
this patch:

    $ ping -I vrf0 -c1 10.2.2.2
    PING 10.2.2.2 (10.2.2.2) from 10.0.0.3 vrf0: 56(84) bytes of data.

>From tcpdump:
    12:59:25.096426 IP 10.0.0.3 > 10.2.2.2: ICMP echo request, id 2113, seq 1, length 64

Now the source address comes from vrf0.

The ipv4 function for selecting source address takes a const argument.
Removing the const requires touching a lot of places, so instead
l3mdev_master_ifindex_rcu is changed to take a const argument and then
do the typecast to non-const as required by netdev_master_upper_dev_get_rcu.
This is similar to what l3mdev_fib_table_rcu does.

IPv6 for unnumbered interfaces appears to be selecting the addresses
properly.

Cc: David Lamparter <david@opensourcerouting.org>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
---
 include/net/l3mdev.h |  4 ++--
 net/ipv4/devinet.c   |  5 +++++
 net/l3mdev/l3mdev.c  | 11 +++++++++--
 3 files changed, 16 insertions(+), 4 deletions(-)

diff --git a/include/net/l3mdev.h b/include/net/l3mdev.h
index 5567d46b3cff..c43a9c73de5e 100644
--- a/include/net/l3mdev.h
+++ b/include/net/l3mdev.h
@@ -39,7 +39,7 @@ struct l3mdev_ops {
 
 #ifdef CONFIG_NET_L3_MASTER_DEV
 
-int l3mdev_master_ifindex_rcu(struct net_device *dev);
+int l3mdev_master_ifindex_rcu(const struct net_device *dev);
 static inline int l3mdev_master_ifindex(struct net_device *dev)
 {
 	int ifindex;
@@ -179,7 +179,7 @@ struct dst_entry *l3mdev_rt6_dst_by_oif(struct net *net,
 
 #else
 
-static inline int l3mdev_master_ifindex_rcu(struct net_device *dev)
+static inline int l3mdev_master_ifindex_rcu(const struct net_device *dev)
 {
 	return 0;
 }
diff --git a/net/ipv4/devinet.c b/net/ipv4/devinet.c
index 29b8d3a7b19b..18d510fa7ee2 100644
--- a/net/ipv4/devinet.c
+++ b/net/ipv4/devinet.c
@@ -1194,6 +1194,7 @@ __be32 inet_select_addr(const struct net_device *dev, __be32 dst, int scope)
 	__be32 addr = 0;
 	struct in_device *in_dev;
 	struct net *net = dev_net(dev);
+	int master_idx;
 
 	rcu_read_lock();
 	in_dev = __in_dev_get_rcu(dev);
@@ -1214,12 +1215,16 @@ __be32 inet_select_addr(const struct net_device *dev, __be32 dst, int scope)
 	if (addr)
 		goto out_unlock;
 no_in_dev:
+	master_idx = l3mdev_master_ifindex_rcu(dev);
 
 	/* Not loopback addresses on loopback should be preferred
 	   in this case. It is important that lo is the first interface
 	   in dev_base list.
 	 */
 	for_each_netdev_rcu(net, dev) {
+		if (l3mdev_master_ifindex_rcu(dev) != master_idx)
+			continue;
+
 		in_dev = __in_dev_get_rcu(dev);
 		if (!in_dev)
 			continue;
diff --git a/net/l3mdev/l3mdev.c b/net/l3mdev/l3mdev.c
index 8e5ead366e7f..e925037fa0df 100644
--- a/net/l3mdev/l3mdev.c
+++ b/net/l3mdev/l3mdev.c
@@ -17,7 +17,7 @@
  *	@dev: targeted interface
  */
 
-int l3mdev_master_ifindex_rcu(struct net_device *dev)
+int l3mdev_master_ifindex_rcu(const struct net_device *dev)
 {
 	int ifindex = 0;
 
@@ -28,8 +28,15 @@ int l3mdev_master_ifindex_rcu(struct net_device *dev)
 		ifindex = dev->ifindex;
 	} else if (netif_is_l3_slave(dev)) {
 		struct net_device *master;
+		struct net_device *_dev = (struct net_device *)dev;
 
-		master = netdev_master_upper_dev_get_rcu(dev);
+		/* netdev_master_upper_dev_get_rcu calls
+		 * list_first_or_null_rcu to walk the upper dev list.
+		 * list_first_or_null_rcu does not handle a const arg. We aren't
+		 * making changes, just want the master device from that list so
+		 * typecast to remove the const
+		 */
+		master = netdev_master_upper_dev_get_rcu(_dev);
 		if (master)
 			ifindex = master->ifindex;
 	}
-- 
2.1.4

[PATCH net-next v3 2/2] net: l3mdev: prefer VRF master for source address selection

[David Ahern]

From: David Lamparter <equinox@diac24.net>

When selecting an address in context of a VRF, the vrf master should be
preferred for address selection.  If it isn't, the user has a hard time
getting the system to select to their preference - the code will pick
the address off the first in-VRF interface it can find, which on a
router could well be a non-routable address.

Signed-off-by: David Lamparter <equinox@diac24.net>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
[dsa: Fixed comment style and removed extra blank link ]
---
v3
- removed blank link

v2
- fixed comment to use preferred style for net code

 net/ipv4/devinet.c | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/net/ipv4/devinet.c b/net/ipv4/devinet.c
index 18d510fa7ee2..8c3df2ccba45 100644
--- a/net/ipv4/devinet.c
+++ b/net/ipv4/devinet.c
@@ -1217,6 +1217,23 @@ __be32 inet_select_addr(const struct net_device *dev, __be32 dst, int scope)
 no_in_dev:
 	master_idx = l3mdev_master_ifindex_rcu(dev);
 
+	/* For VRFs, the VRF device takes the place of the loopback device,
+	 * with addresses on it being preferred.  Note in such cases the
+	 * loopback device will be among the devices that fail the master_idx
+	 * equality check in the loop below.
+	 */
+	if (master_idx &&
+	    (dev = dev_get_by_index_rcu(net, master_idx)) &&
+	    (in_dev = __in_dev_get_rcu(dev))) {
+		for_primary_ifa(in_dev) {
+			if (ifa->ifa_scope != RT_SCOPE_LINK &&
+			    ifa->ifa_scope <= scope) {
+				addr = ifa->ifa_local;
+				goto out_unlock;
+			}
+		} endfor_ifa(in_dev);
+	}
+
 	/* Not loopback addresses on loopback should be preferred
 	   in this case. It is important that lo is the first interface
 	   in dev_base list.
-- 
2.1.4

Re: [PATCH net-next v3 0/2] net: l3mdev: Fix source address for unnumbered deployments

[David Miller]

From: David Ahern <dsa@cumulusnetworks.com>
Date: Wed, 24 Feb 2016 11:47:01 -0800

> David Lamparter noted a use case where the source address selection fails
> to pick an address from a VRF interface - unnumbered interfaces. The use
> case has the VRF device as the VRF local loopback with addresses and
> interfaces enslaved without an address themselves. e.g,
 ...
> ping to the 10.2.2.2 through the L3 domain:
 ...
> picks up the wrong address -- the one from 'lo' not vrf0. And from tcpdump:
>     12:57:29.449128 IP 9.9.9.9 > 10.2.2.2: ICMP echo request, id 2491, seq 1, length 64
> 
> This patch series changes address selection to only consider devices in
> the same L3 domain and to use the VRF device as the L3 domains loopback.
 ...

Series applied, thanks David.