[PATCH 1/9] net: mediatek: update the IRQ part of the binding document

[PATCH 1/9] net: mediatek: update the IRQ part of the binding document

[John Crispin]

The current binding document only describes a single interrupt. Update the
document by adding the 2 other interrupts.

The driver currently only uses a single interrupt. The HW is however able
to using IRQ grouping to split TX and RX onto separate GIC irqs.

Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: devicetree@vger.kernel.org
---
 Documentation/devicetree/bindings/net/mediatek-net.txt |    6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/mediatek-net.txt b/Documentation/devicetree/bindings/net/mediatek-net.txt
index 5ca7929..2f142be 100644
--- a/Documentation/devicetree/bindings/net/mediatek-net.txt
+++ b/Documentation/devicetree/bindings/net/mediatek-net.txt
@@ -9,7 +9,7 @@ have dual GMAC each represented by a child node..
 Required properties:
 - compatible: Should be "mediatek,mt7623-eth"
 - reg: Address and length of the register set for the device
-- interrupts: Should contain the frame engines interrupt
+- interrupts: Should contain the three frame engines interrupts
 - clocks: the clock used by the core
 - clock-names: the names of the clock listed in the clocks property. These are
 	"ethif", "esw", "gp2", "gp1"
@@ -42,7 +42,9 @@ eth: ethernet@1b100000 {
 		 <&ethsys CLK_ETHSYS_GP2>,
 		 <&ethsys CLK_ETHSYS_GP1>;
 	clock-names = "ethif", "esw", "gp2", "gp1";
-	interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_LOW>;
+	interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_LOW
+		      GIC_SPI 199 IRQ_TYPE_LEVEL_LOW
+		      GIC_SPI 198 IRQ_TYPE_LEVEL_LOW>;
 	power-domains = <&scpsys MT2701_POWER_DOMAIN_ETH>;
 	resets = <&ethsys MT2701_ETHSYS_ETH_RST>;
 	reset-names = "eth";
-- 
1.7.10.4

[PATCH 2/9] net: mediatek: watchdog_timeo was not set

[John Crispin]

The original commit failed to set watchdog_timeo. This patch sets
watchdog_timeo to HZ.

Signed-off-by: John Crispin <blogic-p3rKhJxN3npAfugRpC6u6w@public.gmane.org>
---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c |    1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
index e0b68af..bb10d57 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -1645,6 +1645,7 @@ static int mtk_add_mac(struct mtk_eth *eth, struct device_node *np)
 	mac->hw_stats->reg_offset = id * MTK_STAT_OFFSET;
 
 	SET_NETDEV_DEV(eth->netdev[id], eth->dev);
+	eth->netdev[id]->watchdog_timeo = HZ;
 	eth->netdev[id]->netdev_ops = &mtk_netdev_ops;
 	eth->netdev[id]->base_addr = (unsigned long)eth->base;
 	eth->netdev[id]->vlan_features = MTK_HW_FEATURES &
-- 
1.7.10.4

[PATCH 3/9] net: mediatek: mtk_cal_txd_req() returns bad value

[John Crispin]

The code used to also support the PDMA engine, which had 2 packet pointers
per descriptor. Because of this we had to divide the result by 2 and round
it up. This is no longer needed as the code only supports QDMA.

Signed-off-by: John Crispin <blogic-p3rKhJxN3npAfugRpC6u6w@public.gmane.org>
---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
index bb10d57..94cceb8 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -681,7 +681,7 @@ static inline int mtk_cal_txd_req(struct sk_buff *skb)
 		nfrags += skb_shinfo(skb)->nr_frags;
 	}
 
-	return DIV_ROUND_UP(nfrags, 2);
+	return nfrags;
 }
 
 static int mtk_start_xmit(struct sk_buff *skb, struct net_device *dev)
-- 
1.7.10.4

[PATCH 4/9] net: mediatek: remove superfluous reset call

[John Crispin]

HW reset is triggered in the mtk_hw_init() function. There is no need to
also reset the core during probe.

Signed-off-by: John Crispin <blogic-p3rKhJxN3npAfugRpC6u6w@public.gmane.org>
---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c |    4 ----
 1 file changed, 4 deletions(-)

diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
index 94cceb8..a4982e4 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -1679,10 +1679,6 @@ static int mtk_probe(struct platform_device *pdev)
 	struct mtk_eth *eth;
 	int err;
 
-	err = device_reset(&pdev->dev);
-	if (err)
-		return err;
-
 	match = of_match_device(of_mtk_match, &pdev->dev);
 	soc = (struct mtk_soc_data *)match->data;
 
-- 
1.7.10.4

[PATCH 5/9] net: mediatek: fix stop and wakeup of queue

[John Crispin]

The driver supports 2 MACs. Both run on the same DMA ring. If we go
above/below the TX rings threshold value, we always need to wake/stop
the queue of both devices. Not doing to can cause TX stalls and packet
drops on one of the devices.

Signed-off-by: John Crispin <blogic-p3rKhJxN3npAfugRpC6u6w@public.gmane.org>
---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c |   37 +++++++++++++++++++--------
 1 file changed, 27 insertions(+), 10 deletions(-)

diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
index a4982e4..4ebc42e 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -684,6 +684,28 @@ static inline int mtk_cal_txd_req(struct sk_buff *skb)
 	return nfrags;
 }
 
+static void mtk_wake_queue(struct mtk_eth *eth)
+{
+	int i;
+
+	for (i = 0; i < MTK_MAC_COUNT; i++) {
+		if (!eth->netdev[i])
+			continue;
+		netif_wake_queue(eth->netdev[i]);
+	}
+}
+
+static void mtk_stop_queue(struct mtk_eth *eth)
+{
+	int i;
+
+	for (i = 0; i < MTK_MAC_COUNT; i++) {
+		if (!eth->netdev[i])
+			continue;
+		netif_stop_queue(eth->netdev[i]);
+	}
+}
+
 static int mtk_start_xmit(struct sk_buff *skb, struct net_device *dev)
 {
 	struct mtk_mac *mac = netdev_priv(dev);
@@ -695,7 +717,7 @@ static int mtk_start_xmit(struct sk_buff *skb, struct net_device *dev)
 
 	tx_num = mtk_cal_txd_req(skb);
 	if (unlikely(atomic_read(&ring->free_count) <= tx_num)) {
-		netif_stop_queue(dev);
+		mtk_stop_queue(eth);
 		netif_err(eth, tx_queued, dev,
 			  "Tx Ring full when queue awake!\n");
 		return NETDEV_TX_BUSY;
@@ -720,10 +742,10 @@ static int mtk_start_xmit(struct sk_buff *skb, struct net_device *dev)
 		goto drop;
 
 	if (unlikely(atomic_read(&ring->free_count) <= ring->thresh)) {
-		netif_stop_queue(dev);
+		mtk_stop_queue(eth);
 		if (unlikely(atomic_read(&ring->free_count) >
 			     ring->thresh))
-			netif_wake_queue(dev);
+			mtk_wake_queue(eth);
 	}
 
 	return NETDEV_TX_OK;
@@ -897,13 +919,8 @@ static int mtk_poll_tx(struct mtk_eth *eth, int budget, bool *tx_again)
 	if (!total)
 		return 0;
 
-	for (i = 0; i < MTK_MAC_COUNT; i++) {
-		if (!eth->netdev[i] ||
-		    unlikely(!netif_queue_stopped(eth->netdev[i])))
-			continue;
-		if (atomic_read(&ring->free_count) > ring->thresh)
-			netif_wake_queue(eth->netdev[i]);
-	}
+	if (atomic_read(&ring->free_count) > ring->thresh)
+		mtk_wake_queue(eth);
 
 	return total;
 }
-- 
1.7.10.4

[PATCH 8/9] net: mediatek: move the pending_work struct to the device generic struct

[John Crispin]

The worker always touches both netdevs. It is ethernet core and not MAC
specific. We only need one worker, which belongs into the ethernets core
struct.

Signed-off-by: John Crispin <blogic-p3rKhJxN3npAfugRpC6u6w@public.gmane.org>
---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c |   10 ++++------
 drivers/net/ethernet/mediatek/mtk_eth_soc.h |    4 ++--
 2 files changed, 6 insertions(+), 8 deletions(-)

diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
index 8434355..f9f8851 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -1193,7 +1193,7 @@ static void mtk_tx_timeout(struct net_device *dev)
 	eth->netdev[mac->id]->stats.tx_errors++;
 	netif_err(eth, tx_err, dev,
 		  "transmit timed out\n");
-	schedule_work(&mac->pending_work);
+	schedule_work(&eth->pending_work);
 }
 
 static irqreturn_t mtk_handle_irq(int irq, void *_eth)
@@ -1438,7 +1438,7 @@ static void mtk_pending_work(struct work_struct *work)
 
 	/* stop all devices to make sure that dma is properly shut down */
 	for (i = 0; i < MTK_MAC_COUNT; i++) {
-		if (!netif_oper_up(eth->netdev[i]))
+		if (!eth->netdev[i])
 			continue;
 		mtk_stop(eth->netdev[i]);
 		__set_bit(i, &restart);
@@ -1463,15 +1463,13 @@ static int mtk_cleanup(struct mtk_eth *eth)
 	int i;
 
 	for (i = 0; i < MTK_MAC_COUNT; i++) {
-		struct mtk_mac *mac = netdev_priv(eth->netdev[i]);
-
 		if (!eth->netdev[i])
 			continue;
 
 		unregister_netdev(eth->netdev[i]);
 		free_netdev(eth->netdev[i]);
-		cancel_work_sync(&mac->pending_work);
 	}
+	cancel_work_sync(&eth->pending_work);
 
 	return 0;
 }
@@ -1659,7 +1657,6 @@ static int mtk_add_mac(struct mtk_eth *eth, struct device_node *np)
 	mac->id = id;
 	mac->hw = eth;
 	mac->of_node = np;
-	INIT_WORK(&mac->pending_work, mtk_pending_work);
 
 	mac->hw_stats = devm_kzalloc(eth->dev,
 				     sizeof(*mac->hw_stats),
@@ -1761,6 +1758,7 @@ static int mtk_probe(struct platform_device *pdev)
 
 	eth->dev = &pdev->dev;
 	eth->msg_enable = netif_msg_init(mtk_msg_level, MTK_DEFAULT_MSG_ENABLE);
+	INIT_WORK(&eth->pending_work, mtk_pending_work);
 
 	err = mtk_hw_init(eth);
 	if (err)
diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.h b/drivers/net/ethernet/mediatek/mtk_eth_soc.h
index 48a5292..eed626d 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.h
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.h
@@ -363,6 +363,7 @@ struct mtk_rx_ring {
  * @clk_gp1:		The gmac1 clock
  * @clk_gp2:		The gmac2 clock
  * @mii_bus:		If there is a bus we need to create an instance for it
+ * @pending_work:	The workqueue used to reset the dma ring
  */
 
 struct mtk_eth {
@@ -389,6 +390,7 @@ struct mtk_eth {
 	struct clk			*clk_gp1;
 	struct clk			*clk_gp2;
 	struct mii_bus			*mii_bus;
+	struct work_struct		pending_work;
 };
 
 /* struct mtk_mac -	the structure that holds the info about the MACs of the
@@ -398,7 +400,6 @@ struct mtk_eth {
  * @hw:			Backpointer to our main datastruture
  * @hw_stats:		Packet statistics counter
  * @phy_dev:		The attached PHY if available
- * @pending_work:	The workqueue used to reset the dma ring
  */
 struct mtk_mac {
 	int				id;
@@ -406,7 +407,6 @@ struct mtk_mac {
 	struct mtk_eth			*hw;
 	struct mtk_hw_stats		*hw_stats;
 	struct phy_device		*phy_dev;
-	struct work_struct		pending_work;
 };
 
 /* the struct describing the SoC. these are declared in the soc_xyz.c files */
-- 
1.7.10.4

[PATCH 9/9] net: mediatek: do not set the QID field in the TX DMA descriptors

[John Crispin]

The QID field gets set to the mac id. This made the DMA linked list queue
the traffic of each MAC on a different internal queue. However during long
term testing we found that this will cause traffic stalls as the multi
queue setup requires a more complete initialisation which is not part of
the upstream driver yet.

This patch removes the code setting the QID field, resulting in all
traffic ending up in queue 0 which works without any special setup.

Signed-off-by: John Crispin <blogic-p3rKhJxN3npAfugRpC6u6w@public.gmane.org>
---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c |    3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
index f9f8851..8163047 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -603,8 +603,7 @@ static int mtk_tx_map(struct sk_buff *skb, struct net_device *dev,
 			WRITE_ONCE(txd->txd1, mapped_addr);
 			WRITE_ONCE(txd->txd3, (TX_DMA_SWC |
 					       TX_DMA_PLEN0(frag_map_size) |
-					       last_frag * TX_DMA_LS0) |
-					       mac->id);
+					       last_frag * TX_DMA_LS0));
 			WRITE_ONCE(txd->txd4, 0);
 
 			tx_buf->skb = (struct sk_buff *)MTK_DMA_DUMMY_DESC;
-- 
1.7.10.4

Re: [PATCH 1/9] net: mediatek: update the IRQ part of the binding document

[David Miller]

Every patch series must begin with a postings labelled "[PATCH 0/9] ..."
which explains what the series is doing, how it is implementing that,
and why it is implemented that way.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 6/9] net: mediatek: fix mtk_pending_work

[John Crispin]

The driver supports 2 MACs. Both run on the same DMA ring. If we hit a TX
timeout we need to stop both netdevs before restarting them again. If we
don't do this, mtk_stop() wont shutdown DMA and the consecutive call to
mtk_open() wont restart DMA and enable IRQs.

Signed-off-by: John Crispin <blogic@openwrt.org>
---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c |   31 ++++++++++++++++++---------
 1 file changed, 21 insertions(+), 10 deletions(-)

diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
index 4ebc42e..60b66ab 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -1430,19 +1430,30 @@ static int mtk_do_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
 
 static void mtk_pending_work(struct work_struct *work)
 {
-	struct mtk_mac *mac = container_of(work, struct mtk_mac, pending_work);
-	struct mtk_eth *eth = mac->hw;
-	struct net_device *dev = eth->netdev[mac->id];
-	int err;
+	struct mtk_eth *eth = container_of(work, struct mtk_eth, pending_work);
+	int err, i;
+	unsigned long restart = 0;
 
 	rtnl_lock();
-	mtk_stop(dev);
 
-	err = mtk_open(dev);
-	if (err) {
-		netif_alert(eth, ifup, dev,
-			    "Driver up/down cycle failed, closing device.\n");
-		dev_close(dev);
+	/* stop all devices to make sure that dma is properly shut down */
+	for (i = 0; i < MTK_MAC_COUNT; i++) {
+		if (!netif_oper_up(eth->netdev[i]))
+			continue;
+		mtk_stop(eth->netdev[i]);
+		__set_bit(i, &restart);
+	}
+
+	/* restart DMA and enable IRQs */
+	for (i = 0; i < MTK_MAC_COUNT; i++) {
+		if (!test_bit(i, &restart))
+			continue;
+		err = mtk_open(eth->netdev[i]);
+		if (err) {
+			netif_alert(eth, ifup, eth->netdev[i],
+			      "Driver up/down cycle failed, closing device.\n");
+			dev_close(eth->netdev[i]);
+		}
 	}
 	rtnl_unlock();
 }
-- 
1.7.10.4

[PATCH 7/9] net: mediatek: fix TX locking

[John Crispin]

Inside the TX path there is a lock inside the tx_map function. This is
however too late. The patch moves the lock to the start of the xmit
function right before the free count check of the DMA ring happens.
If we do not do this, the code becomes racy leading to TX stalls and
dropped packets. This happens as there are 2 netdevs running on the
same physical DMA ring.

Signed-off-by: John Crispin <blogic@openwrt.org>
---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c |   20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)

diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
index 60b66ab..8434355 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -536,7 +536,6 @@ static int mtk_tx_map(struct sk_buff *skb, struct net_device *dev,
 	struct mtk_eth *eth = mac->hw;
 	struct mtk_tx_dma *itxd, *txd;
 	struct mtk_tx_buf *tx_buf;
-	unsigned long flags;
 	dma_addr_t mapped_addr;
 	unsigned int nr_frags;
 	int i, n_desc = 1;
@@ -568,11 +567,6 @@ static int mtk_tx_map(struct sk_buff *skb, struct net_device *dev,
 	if (unlikely(dma_mapping_error(&dev->dev, mapped_addr)))
 		return -ENOMEM;
 
-	/* normally we can rely on the stack not calling this more than once,
-	 * however we have 2 queues running ont he same ring so we need to lock
-	 * the ring access
-	 */
-	spin_lock_irqsave(&eth->page_lock, flags);
 	WRITE_ONCE(itxd->txd1, mapped_addr);
 	tx_buf->flags |= MTK_TX_FLAGS_SINGLE0;
 	dma_unmap_addr_set(tx_buf, dma_addr0, mapped_addr);
@@ -632,8 +626,6 @@ static int mtk_tx_map(struct sk_buff *skb, struct net_device *dev,
 	WRITE_ONCE(itxd->txd3, (TX_DMA_SWC | TX_DMA_PLEN0(skb_headlen(skb)) |
 				(!nr_frags * TX_DMA_LS0)));
 
-	spin_unlock_irqrestore(&eth->page_lock, flags);
-
 	netdev_sent_queue(dev, skb->len);
 	skb_tx_timestamp(skb);
 
@@ -661,8 +653,6 @@ err_dma:
 		itxd = mtk_qdma_phys_to_virt(ring, itxd->txd2);
 	} while (itxd != txd);
 
-	spin_unlock_irqrestore(&eth->page_lock, flags);
-
 	return -ENOMEM;
 }
 
@@ -712,14 +702,22 @@ static int mtk_start_xmit(struct sk_buff *skb, struct net_device *dev)
 	struct mtk_eth *eth = mac->hw;
 	struct mtk_tx_ring *ring = &eth->tx_ring;
 	struct net_device_stats *stats = &dev->stats;
+	unsigned long flags;
 	bool gso = false;
 	int tx_num;
 
+	/* normally we can rely on the stack not calling this more than once,
+	 * however we have 2 queues running ont he same ring so we need to lock
+	 * the ring access
+	 */
+	spin_lock_irqsave(&eth->page_lock, flags);
+
 	tx_num = mtk_cal_txd_req(skb);
 	if (unlikely(atomic_read(&ring->free_count) <= tx_num)) {
 		mtk_stop_queue(eth);
 		netif_err(eth, tx_queued, dev,
 			  "Tx Ring full when queue awake!\n");
+		spin_unlock_irqrestore(&eth->page_lock, flags);
 		return NETDEV_TX_BUSY;
 	}
 
@@ -747,10 +745,12 @@ static int mtk_start_xmit(struct sk_buff *skb, struct net_device *dev)
 			     ring->thresh))
 			mtk_wake_queue(eth);
 	}
+	spin_unlock_irqrestore(&eth->page_lock, flags);
 
 	return NETDEV_TX_OK;
 
 drop:
+	spin_unlock_irqrestore(&eth->page_lock, flags);
 	stats->tx_dropped++;
 	dev_kfree_skb(skb);
 	return NETDEV_TX_OK;
-- 
1.7.10.4

Re: [PATCH 1/9] net: mediatek: update the IRQ part of the binding document

[Rob Herring]

On Thu, Apr 07, 2016 at 07:57:48PM +0200, John Crispin wrote:
> The current binding document only describes a single interrupt. Update the
> document by adding the 2 other interrupts.
> 
> The driver currently only uses a single interrupt. The HW is however able
> to using IRQ grouping to split TX and RX onto separate GIC irqs.

I assume you aren't breaking existing DTs, and the driver will continue 
to work with a single irq specified?

> 
> Signed-off-by: John Crispin <blogic@openwrt.org>
> Cc: devicetree@vger.kernel.org
> ---
>  Documentation/devicetree/bindings/net/mediatek-net.txt |    6 ++++--
>  1 file changed, 4 insertions(+), 2 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/net/mediatek-net.txt b/Documentation/devicetree/bindings/net/mediatek-net.txt
> index 5ca7929..2f142be 100644
> --- a/Documentation/devicetree/bindings/net/mediatek-net.txt
> +++ b/Documentation/devicetree/bindings/net/mediatek-net.txt
> @@ -9,7 +9,7 @@ have dual GMAC each represented by a child node..
>  Required properties:
>  - compatible: Should be "mediatek,mt7623-eth"
>  - reg: Address and length of the register set for the device
> -- interrupts: Should contain the frame engines interrupt
> +- interrupts: Should contain the three frame engines interrupts

Need to define what each irq is and the order.

>  - clocks: the clock used by the core
>  - clock-names: the names of the clock listed in the clocks property. These are
>  	"ethif", "esw", "gp2", "gp1"
> @@ -42,7 +42,9 @@ eth: ethernet@1b100000 {
>  		 <&ethsys CLK_ETHSYS_GP2>,
>  		 <&ethsys CLK_ETHSYS_GP1>;
>  	clock-names = "ethif", "esw", "gp2", "gp1";
> -	interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_LOW>;
> +	interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_LOW
> +		      GIC_SPI 199 IRQ_TYPE_LEVEL_LOW
> +		      GIC_SPI 198 IRQ_TYPE_LEVEL_LOW>;
>  	power-domains = <&scpsys MT2701_POWER_DOMAIN_ETH>;
>  	resets = <&ethsys MT2701_ETHSYS_ETH_RST>;
>  	reset-names = "eth";
> -- 
> 1.7.10.4
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html